Topone Kitchen EV-S1M User manual

ELECTRIC OVEN
Operation and Installation instructions
Please read this instruction carefully before using it
This instruction contains a service guide, please keep it safe
The company specializes in the production of "electric oven"
series, single-layer / double-layer / three-layer series of products.
Our products are designed with the advantages of similar foreign
products, and have the characteristics of unique design, excellent
manufacture, convenient operation, fast heating, good heat preservation,
low energy consumption and so on. It is an ideal equipment
for large food central factories, bakeries, shops and unit canteens
to process ordinary bread, cakes, moon cakes and other food.
Thank you for purchasing our products. Please read the operating
instructions carefully before using this product. There are general
troubleshooting methods in this book that are easy to learn. Please
take good care of this manual for a rainy day. Please strictly abide
by the special precautions mentioned below.
Special Remarks
1.Users should strictly follow the instructions, according to the oven
special warning board to do a good job of prevention.
2.The type of power used by the equipment must be the same as
that marked on the nameplate of this machine.
3.This machine must be reliably grounded and installed with leakage
protection circuit breaker.
Foreword
01 02
Safety instructions Installation Use method fault handling
4.This machine cable needs to be replaced due to aging or other
reasons, be sure to use oil-resistant cable (YΣM series cable),
not ordinary rubber sheathed cable.

8. It is strictly forbidden to bake flammable, explosive and
corrosive items.
9. This machine must have a special guard and operation after
electrification.
10. Represents the danger caused by a dangerous voltage.
11.Use trunks to identify terminals that connect to each other
so that all parts of the equipment or system reach the same
potential, which is not necessarily a grounding potential,
such as a local interconnect.
(Model: E V- S 1 M )
Clock usage
1. Adjust Time Press
key increase time
Key reduce time
2. Start clock function
After adjusting the time, press
the START/STOP key, the clock
starts to work;
3.End clock function
Press the START/STOP key
and the clock stops working;
4.The clock function in the
working process , the red dot
in the lower right corner of the
number will always flicker, when
the time countdown is 0.
03 04
Safety instructions Installation Use method fault handling Safety instructions Installation Use method fault handling
The OUT indicator lights up and sends out a long bee sound.
When the warning has arrived, press the START/STOP key,
the OUT indicator lights out, the buzzer disappears, the red
dot in the lower right corner of the number will stop flashing,
and the clock function will turn off.
5.For persons with physical, sensory or intellectual defects, or with
a lack of experience and knowledge, including children, it is not suitable
to operate the equipment.
7.Only qualified professional maintenance personnel can install, inspect,
repair and maintain this machine.
6.When replacing electrical parts and repairing electrical circuits, the
power supply must be completely disconnected and the gas source must
be completely turned off.

05 06
Product parameters
Model Rate d v oltage Rate d p ower Net weight Gross weight
EV-S1M 220V/50Hz 3200W 30.5kg 42.5kg
EV-S2M 220V/50Hz 6400W 61kg 78kg
EV-S3M 220V/50Hz 9600W 92kg 112kg
I. Overview
1.Features: Electric oven type electric oven (far infrared
heating tube heating)
2.Main uses: suitable for baking all kinds of ordinary bread,
cakes, moon cakes and other Chinese and Western food,
special or ultra-thin baking products need to be specially
designed and customized to produce perfect results.
Door handle / Installation diagramDisassembly
Safety instructions Installation Use method fault handling
3.Varieties and specifications: single-layer electric oven,
double-layer electric oven and three-layer electric oven.
II. Structural characteristics and working principles
1.Each layer can be used independently and simultaneously
, and can also be used by single layer and single fire.
2.The upper and lower fire of each floor can be controlled
independently.
3.The furnace temperature can be adjusted arbitrarily in
the range of room temperature ~ 300 degrees Celsius, and
the furnace temperature can be kept constant automatically.
4.Equipped with non-self-reset circuit breaker and all-pole
disconnection device to ensure that the oven works more safely.
5.When it is necessary to control the temperature at a fixed
time, a timer can be installed.
III. Installation and commissioning
1.Customers according to the rated power of the equipment,
equipped with leakage protection circuit breaker.
2.After checking the electric oven and confirming that there is no
collision or damage in the transportation process, push the equipment
to the ventilated position to install, and connect the furnace outlet
cable to the circuit breaker with leakage protection.
3.After the wiring is completed, turn on the power and check
whether the thermostat and related switches are abnormal.
4.When the new oven heats up, there will be a strange smell
in the oven. It is recommended to put a plate of onions into the
oven to bake, remove the smell and then bake the food.
Safety instructions Installation Use method fault handling
Disassembly Installation

5.The new oven in the first few days of use, please pay more
attention to observe, one is familiar with the performance of the
equipment to facilitate baking, and the other is to find problems
can be communicated in time. Because the violent vibration in
transportation may make the screw loose, and even affect the
normal work of the digital display instrument, we must pay
attention to check and deal with it in time when installing the
new machine.
6.This oven belongs to the appliance of "permanently connecting
to fixed wiring". According to the working environment,the user
can connect the self-provided power cord (YZM) to the terminal
of the electric oven of the oven according to the working
environment. For the convenience of users, the oven
has been provided with a power cord at random when it leaves
the factory. When using the power cord, please do not connect
the plug directly, be sure to connect the power cord to the circuit
breaker with leakage protector.
7.The equipotential connection terminal on the oven shell
is a special grounding terminal, which is not the protective
grounding terminal used to connect the universal wire, but
the terminal used to connect the external equipotential wire
in the apparatus should be allowed to connect the wire with
a nominal cross-sectional area of 2.5-6mm², and the well tool
should not be used to provide grounding continuity between
different parts of the instrument. These wires should not be
loosened without the help of tools.
8.Bake at least 50cm away from the wall.
9.Ovens can not be stored and used in the open air or in
particularly wet or water dripping places.
07 08
IV. Use and operation
1.Close the leakage circuit breaker, set the oven temperature,
turn on the power switch of each layer, and heat up the electric
heating pipe.
3.According to the different requirements of the baked food,
the temperature of "upper fire" and "lower fire" can be adju
sted respectively to make the food get the best fire color.
4.If the furnace fire is uneven in use, the method of
adjusting the cake plate (commonly known as the adjusting
plate) can be used to solve the problem.
5.Avoid opening and closing the furnace door as much as
possible when in use.
6.Do not install fans above or in front of the furnace door.
Note ∶ In order to avoid the danger caused by the wrong
reset of the thermal circuit breaker, the appliance can not
supply power through the external device, such as timer
or connected to the circuit that is timed and broken by the
general component.
V. Fault analysis and troubleshooting
Affected by power supply, operation, quality of accessories
, environment and other factors, the machine will occasionally
have local faults that need to be repaired and dealt with.
All kinds of possible faults are listed as follows:
Safety instructions Installation Use method fault handling Safety instructions Installation Use method fault handling
2.The temperature of lower fire and upper fire can be
controlled separately: close the switch of lower fire, work
separately; close the switch of upper and lower fire, work
alone, close the switch of upper and lower fire and fire at
the same time, and work at the same time.

VI. Daily maintenance
1.After using the oven every day, the thermostat of each layer
must be returned to zero. Disconnect the total power leakage
circuit breaker.
2.When cleaning and maintaining the oven, be sure to disconnect
the leakage protection switch, and direct flushing of the water pipe
is strictly prohibited when cleaning.
3.Before getting off work every day, clean up the food residue in
the furnace so as not to affect the heat transfer in the furnace.
4.Wipe the furnace body and observation window with a wiping
cloth regularly to keep the furnace body clean.
5.Operate in strict accordance with the instructions.
09 10
Fault phenomenon Cause analysis
Processing methods
When the power
switch is closed,
the oven lights
are not on
①Power switch
failure
②Fuse fault
①Replace the
power switch
②Replace the
molten core
The color of baked
food is uneven, raw
and cooked, the
furnace temperature
rises slowly, and the
baking time is longer
than normal.
①External connection
line of heating tube
is broken
②Burn-out of electric
heating wire in
heating tube
③AC contactor failure
④Furnace bottom plate
or baking dish is out
of shape.
⑤The power cord is
loose or out of phase.
①Connect the external
connection cable of
the heating tube
②Replacement of
broken heating tubes
③Replace AC contactor
④Repair of flat furnace
bottom or baking disk
⑤Reconnect the power
cord
Can not automatically
control the temperature
(red light / green light
can not be automatically
converted)
Temperature
control failure
Send the thermostat
and sensor back to
repair or replace the
oven with professional
thermostat
Furnace door
deformation
After working for a
period of time, the
furnace door may
produce thermal
expansion deformation,
resulting in air leakage.
Put the wood block on
the corner of the air-tight
furnace door and knock
on the corner of the
air-leaking furnace door
with Bakelite until it is
flattened (a small amount
of air leakage is allowed
in the oven door).
NO.
1
2
3
4
Thank you for choosing our equipment, which is mainly
used for the manufacture or baking of ordinary cakes,
cakes and other products, and shows excellent performance.
In order to better serve the users, the following instructions
are made:
1. When purchasing equipment, you must fill in the warranty
card and sign it by the distributor before it can take effect, and
then repair it with this order.
2. Within one year from the date of purchase, due to the quality
problems of our equipment parts or the whole machine, our
company will carry out three guarantees and repair them free
of charge.
3. Our company will not be responsible for the damage caused
by the collision caused by the installation, use or transportation
not in accordance with the operating instructions.
Safety instructions Installation Use method fault handling Safety instructions Installation Use method fault handling

11 12
4. When there is something wrong with the equipment, the user
should first ask the professional to check and repair. If the fault
cannot be removed, the after-sales service technician of our
company should be informed by telephone as soon as possible
to solve the problem.
5. Our company is responsible for providing free replacement of
accessories within one year (need to trade in old parts for new
ones).All expenses outside the scope of the three packages shall
be borne by the user.
Warranty card
Warranty commitment
1. On the premise that users abide by the rules of use and
maintenance, the company will provide an one-year free warranty
(calculated from the date of purchase) for damage to parts caused
by product quality problems.
2. The following circumstances are not covered by the warranty,
and the user is required to pay the corresponding material fee and
maintenance fee.
(1) Damage caused by violation of operating procedures.
(2) Damage caused by unmatched power supply and parts.
(3) Damage caused by non-compliance with the requirements of
the instructions during installation and use.
(4) All man-made or accidental damage to the product.
(5) Damage caused by self-repair or alteration without the approval
of the Company.
(6)The aging, damage or scratches of the shell on the surface of
the product.
(7) A free warranty period of more than 1 year.
(1) after the expiration of the free warranty, users can still get the paid
maintenance service provided by our company and charge the cost
of maintenance.
4. Please save this warranty card properly after purchasing the
product. This warranty card must be provided during the warranty,
otherwise it will be invalid.
Safety instructions Installation Use method fault handling Safety instructions Installation Use method fault handling
User information
User name Telephone Zip code
Address
Product name
Purchase date
Product model
Factory code
Maintenance
date
Fault content
Fault situation Replacement accessories
Maintenance unit Maintenance man
After the product maintenance during the warranty period, the maintenance
personnel shall fill in the product maintenance contents in the 《Product maintenance
record form》.
Matters needing attention
※
3. If users find quality problems in use, please contact customer
service and provide a clear photo of this warranty card. After
customer service checks user information and factory number,
we will provide warranty service to users as soon as possible.

13 14
Manufacturer: Foshan Topone Electrical Appliances Co., Ltd
Address: No. 16 Fuyuan Industry Zone, Longchong,
Ronggui,Shunde District, Foshan City
Free Customer Service Telephone: [phone]
Safety instructions Installation Use method fault handling Safety instructions Installation Use method fault handling
Statement
With the technical innovation and improvement of the product,
some of the parameters may be changed, the changed
parameters have no retroactive effect on this product, please
take the product nameplate parameters as standard.
All the illustrations shown in this manual are based on the
appearance of the standard model and are only used as
examples to illustrate the use. the actual appearance should
be based on the products purchased.
If there is any change in the contents of this manual, we will
make an announcement through the company's official website
without further notice, unless it is clearly stated in the notice
that in principle, the content of the change has no traceability
to the product.
The right to interpret the relevant terms of this manual
belongs to Foshan Topone Electrical Appliances Co., Ltd
Manufacturer: Foshan Topone Electrical Appliances Co., Ltd
Address: No. 16 Fuyuan Industry Zone, Longchong, Ronggui,
Shunde District, Foshan City