Topper 100M User manual

1
Audio and Video Extender 100M
ⅠProduct Introduction
This product includes a Sender (VGA Extender Sender) and a Receiver (VGA
Extender Receiver). It can extend Audio and Video of the computer through a
single cable. User can see the picture and listen to the sound of the computer from
a long distance. Besides, the brightness and clearness of remote picture image is
adjustable by hand.
This product can be widely used in computer and monitor field, large screen
advertisement, education, bank and industry, etc.
ⅡTechnical Specification
Size: 110mm*70mm*25mm
Weight: 1.0kg
Extend Length: VGA-100H 1m----100m
Cable Type: CAT5, CAT5E, CAT6, UTP, CAT5E and UTP is
suggested.
Resolution: Max support 1920*1440
Video type: VGA, SVGA, XGA, SXGA, UXGA
Video Standard: 0.7Vpp
Connector: HDB15, RJ45, RCA
Sender Power: DC12V/1A
Receiver Power: DC12V/1A
ⅢPacking Instruction
When you open the packing, you will find:
1. 1 x Sender (Video Extender Sender)
2. 1 x Receiver Video Extender Receiver)
3.2 x DC12V Power adapter
4. 1 x VGA cable (1.5m)
5. 1 x Audio Link Cable (male to male,1m) for Sender
6. 1 x User Guide
2
ⅣInstallation
Typical application
Installation Steps:
Please adjust the computer, VGA display equipment and prepare enough cable.
CAT5E cable sequence should be: orange-white (1), orange (2),
green-white(3), blue(4), blue-white(5), green(6), brown-white(7), brown(8).
Make sure you switch off the power before you install it. Please follow the
following steps
(1) Connect VGA Video port of the Sender (VGA IN) with VGA Video port of
the display card by using 1.5m VGAcable.
(2) Connect local monitor with VGA video port of the Sender if it is needed to
display.
(3) Connect the port of the sound card of the computer with Audio port of the
Sender by using 1m Audio Link Cable (Audio)
(4) Insert the CAT5E cable to RJ45 port of the Sender.
(5) Insert the power adapter to the power of the Sender, and insert the power
adapter to the AC socket.
(6) Insert Video port of the remote monitor to VGAport of the Receiver (VGA)

3
(7) Connect Audio port of the Receiver (Audio) with the sound broadcast
equipment.
(8) Connect CAT5E cable with RJ45 of the Receiver.
(9) Insert the power adapter to the power of the Receiver, and insert the power
adapter to the AC socket.
(10) Switch on power of the Receiver, then user can see the light of the Receiver
is on.
(11) Switch on the power of the Sender, and then user can see the light of the
Sender is on. Switch on the computer. Use screwdriver to adjust the
brightness and clearness of remote picture image (B and C port on the
Receiver). ¡B¡ is for brightness and chromaticity, ¡C¡ port is clearness.
Ⅴ. Light Instruction
1 Sender: red light: Sender is on if the light is on.
Blue light: Video signal is normal if the light is on
2 Receiver: red light: Receiver is on if the light is on
Blue light:Audio signal is normal if the light is on
4
Ⅵ. Trouble Shooting
S/N Problem Solution
1 Remote red light is not on 1 Check whether the power of the
Receiver is tighten
2 Check the credibility of the connector of
the CAT5E
3 Check whether the VGA port becomes
less crowded
4 Check CAT5 cable sequence
2 Remote display equipment
can not use
1 check whether the CAT5E cable is
connected well
2 VGA video cable is not connected