Tormach PCNC 440 User manual

TECHNICAL DOCUMENT
TORMACH.COM
Page 1
©Tormach® 2020. All rights reserved.
Specicaons subject to change without noce.
TD10403_PCNC440_Stand_0120A
INSTALLATION GUIDE: PCNC 440 STAND
Product Idencaon: PCNC 440 Stand (PN 35671)
Purpose: This document details assembly of the PCNC 440 stand.
Item# PCNC 440 Stand Qty.
1Back Panel 1
2Side Panel 2
3Upper Support 2
4Lower Support 2
5 Door Assembly 1
6 Mounng Block 4
7Leg 4
8Middle Shelf 1
9Lower Shelf 1
10 Top Panel 1
11 10-32 x 1/2” Phillips Screw 8
12 10-32 x 3/8” Phillips Screw 60
13 M12 x 20 mm Socket Head Cap Screw 12
14 1/4-20 x 3/8” Phillips Screw 4
15 Door Lock 2
16 M12 Lock Washer 12
17 M12 Flat Washer 4
18 Leveling Foot 4
19 10-32 Nut 12
20 M12 Nut 4
NOTE: Some fasteners in this kit may include extras.
If any of these items are missing, contact Tormach
Customer Service at [phone] for a replacement.

Tormach, Inc.
P: 608.849.8381 / F: 209.885.4534
tormach.com
TECHNICAL DOCUMENT
Page 2
©Tormach® 2020. All rights reserved.
Specicaons subject to change without noce.
TD10403_PCNC440_Stand_0120A
1 2 5
6 7
8 9 10
11 12
17
14 15 16
4
3
Stand Parts
13
20
19
18

Tormach, Inc.
P: 608.849.8381 / F: 209.885.4534
tormach.com
TECHNICAL DOCUMENT
Page 3
©Tormach® 2020. All rights reserved.
Specicaons subject to change without noce.
TD10403_PCNC440_Stand_0120A
Stand Assembly
NOTE: Operator may choose to use thread-locking
uid (not included) on stand screws during assembly.
1. Using 12 10-32 x 3/8” Phillips Screws, aach
four Legs to two Side Panels (see Figure 1).
NOTE: Middle Shelf holes should be oriented as shown
in Figure 1.
2. Using six 10-32 x 3/8” Phillips Screws, aach
Back Panel (see Figure 2).
Using 10-32 X3/8 Screw fasten
the side panels the the legs as
shown
Figure 1
Using 10-32X3/8 screw fasten the rear
panel as shown
Figure 2

Tormach, Inc.
P: 608.849.8381 / F: 209.885.4534
tormach.com
TECHNICAL DOCUMENT
Page 4
©Tormach® 2020. All rights reserved.
Specicaons subject to change without noce.
TD10403_PCNC440_Stand_0120A
3. Using eight 10-32 x 3/8” Phillips Screws, aach
Lower Shelf (see Figure 3).
NOTE: In this step, do not put any screws in back side
of the Lower Shelf; these will be added later.
4. Using 12 10-32 x 3/8” Phillips Screws, aach
Middle Shelf (see Figure 4).
Using 10-32 X3/8 Screw fasten
the bottom shelf as shown
In this step do notput any
screws in the back side of the
bottom shelf.
They will be added at a later
step
Figure 3
Using 10-32 X3/8 Screw fasten
the middle shelf as shown
Figure 4

Tormach, Inc.
P: 608.849.8381 / F: 209.885.4534
tormach.com
TECHNICAL DOCUMENT
Page 5
©Tormach® 2020. All rights reserved.
Specicaons subject to change without noce.
TD10403_PCNC440_Stand_0120A
5. Using six 10-32 x 3/8” Phillips Screws, aach
Door Assembly (see Figure 5).
NOTE: In this step, do not put any screws in front
surface of Lower Shelf; these will be added later.
6. Using 16 10-32 x 3/8” Phillips Screws, aach
Top Panel to assembly (see Figure 6).
Figure 5
Figure 6

Tormach, Inc.
P: 608.849.8381 / F: 209.885.4534
tormach.com
TECHNICAL DOCUMENT
Page 6
©Tormach® 2020. All rights reserved.
Specicaons subject to change without noce.
TD10403_PCNC440_Stand_0120A
7. Place four Mounng Blocks
on stand and align each with
pre-drilled holes in stand
top (see Figure 7).
8. Place one Upper Support
underneath stand top with
support angles oriented as
shown in Figure 7; align with
pre-drilled holes in stand
top.
9. Using two M12 x 20 mm
Socket Head Cap Screws
and two M12 Lock Washers,
aach Upper Support from
underside of stand top into
two Mounng Blocks (see
Figure 7).
10. Repeat Steps 8-9 for second
Upper Support.
Figure 7

Tormach, Inc.
P: 608.849.8381 / F: 209.885.4534
tormach.com
TECHNICAL DOCUMENT
Page 7
©Tormach® 2020. All rights reserved.
Specicaons subject to change without noce.
TD10403_PCNC440_Stand_0120A
11. Using one M12 x 20 mm Socket Head Cap
Screw and one M12 Lock Washer, secure
Mounng Block to stand top; repeat for all
four Mounng Blocks.
NOTE: Center hole in each Mounng Block is used
for mounng mill to chip pan. For informaon on
assembly, refer to PCNC 440 Operator Manual.
12. Using one M12 x 20 mm Socket Head Cap
Screw and one M12 Flat Washer, secure end
of Upper Support to corner of stand top (see
Figure 8); repeat for all four ends of Upper
Support.
13. Ax each M12 x 20 mm Socket Head Cap
Screw and M12 Flat Washer assembly on
Upper Support with one M12 Lock Washer
and one M12 Nut as shown in Figure 8.
14. Place one Lower Support at front of
stand as shown in Figure 9;insert
two 1/4-20 x 3/8” Phillips Screws
through stand front, through Leg,
and screw into Lower Support;
repeat for back of stand.
NOTE: Some previously installed items not
shown in Figure 9.
15. Insert four 10-32 x 1/2” Phillips
Screws through front of stand and
screw into Lower Support; repeat
for back of stand.
Figure 8
Upper Support
Stand Top
M12 Nut
M12 Flat Washer
M12 Lock Washer
M12 x 20 mm
Socket Head Cap
Screw
Figure 9
Front of
stand

Tormach, Inc.
P: 608.849.8381 / F: 209.885.4534
tormach.com
TECHNICAL DOCUMENT
Page 8
©Tormach® 2020. All rights reserved.
Specicaons subject to change without noce.
TD10403_PCNC440_Stand_0120A
16. Place cardboard (or similar) on oor to protect
stand; lay stand on its back (see Figure 9).
17. Screw one M12 Nut onto each of the four
Leveling Feet; screw Leveling Feet into four
Legs as shown in Figure 10.
18. Return Stand to upright posion; aach one
Door Lock to each door (see Figure 11).
19. Adjust feet as needed to level stand.
Figure 11
Figure 10