Toro WiFi-LoRa TEMPUS-AG-WF User manual

TEMPUS-AG-WF
USER’S GUIDE
EN
TEMPUS-AG-WF
Base Station WiFi
Base Station WiFi
WiFi-LoRaTM Gateway
WiFi-LoRaTM Gateway

Toro TEMPUS-AG-WF
2
TEMPUS-AG-WF is a WiFi-LoRaTM gateway that allows data transmission between the MyToroTempus application or
platform and TEMPUS-AG devices (CT, MS, PR, MV).
TEMPUS-AG-WF connects to the MyToroTempus, application or web platform, via Internet WiFi.
TEMPUS-AG-WF can communicate via LoRaTM(long range radio connection) with up to 30 devices among TEMPUS-AG-
CT/MV/MS/PR.
INTRODUCTION
SPECIFICATION
DIMENSIONS
Width: 8 cm
Height: 8,2 cm
Depth: 1,3 cm
INSTALLATION
Permissible humidity: 90% (relative humidity)
Ambient temperature of product use: 0°C to 40°C
Warranty: 2 years
POWER SUPPLY
Power supply unit: INPUT : 100-240V ~ 0.2A Max 50/60Hz
OUTPUT: 12V 0.5A
FEATURES
Frequency band used and power emitted max :
Bluetooth®: [2400-2483.5]Mhz, 1mW
WiFi: 2.4Ghz , 25mW
LoRaTM: [868-868.6]Mhz, 25mW
RECOMMENDATION
TEMPUS-AG product installation requires a pre-audit phase in order to check the connection of the products in their
intended locations.
To optimize the connection between the TEMPUS-AG-WF and the TEMPUS-AG devices, it is strongly recommended :
1. Position the TEMPUS-AG-WF or its remote antenna as high as possible, with a clear environment.
2. Test the LoRaTM connection between TEMPUS-AG-WF and the devices using the test tool present in the
MyToroTempus App.
LoRaTM connection frequency between TEMPUS-AG-WF and his devices is 3 minutes.
Remotely, each modification of program or manual control will be eective after 3 minutes.
On the TEMPUS-AG-MS device :
- Recording of the count, every 15 minutes.
- Feedback, every 3 minutes.
Read the following safety instructions carefully before installing or using the TEMPUS-AG-WF.
Be sure to striclty respect precautions of use.
TEMPUS-AG-WF must be installed indoors or under cover.
Install your product so that the socket outlet is near the equipment.
The socket is a disconnecting device, in case of problem, it must be easily accessible at all times. Make sure the
outlet on which your power transformer is plugged has overcurrent protection and circuit breaker type short circuit
protection 16mA.
Use only the power supply unit provided with the product (model MU06-T120050-C5),
INPUT : 100-240V ~ 0.2A Max 50/60Hz OUTPUT : 12V - 0.5A.

Toro TEMPUS-AG-WF
3
Step 2
INSTALLATION AND ASSOCIATION
1. Make sure the place where you want to install the TEMPUS-AG-WF is covered by the Wi-Fi connection of
your internet box.
2. Screw on the antenna, and connect the 120VAC power supply provided with the TEMPUS-AG-WF
3. Verify that the Bluetooth® is activated on the settings of your smartphone.
4. Launch MyToroTempus app from your smartphone or tablet.
5. Click on the «Add a controller» button or on the «+» button
Step 1
1. On your smartphone or tablet, go to the «App Store» or to the «Play Store».
2. Search for «The Toro Company» in the search bar.
Developer
The Toro Company
4. Once installed, activate the Bluetooth® of your smartphone or tablet.
APP DOWNLOAD
3. Once found, download the MyToroTempus App
To use TEMPUS-AG-WF you need to create your MyToroTempus account.
1. Launch MyToroTempus app from your smartphone and/or tablet.
2. Select the "Registration" button.
3. Follow the step described on the app.
CREATE AN ACCOUNT
Note: if you already have an account on the MyToroTempusAG.com platform, you must use the same credentials
No device already
installed
Devices are already
installed
TEMPUS-AG-WF

Toro TEMPUS-AG-WF
4
Select the TEMPUS-AG-
WF icon from the devices
list
Select the required TEMPUS-AG-WF
to be installed from
the list of the available devices
Note: To identify your
TEMPUS-AG-WF among
the nearby WF gateways,
please refer to the
«Default name» present
on its product label."
Select the WiFi network access
to which you want to connect
your TEMPUS-AG-WF by clicking
on the corresponding line or
«Ignore» if your TEMPUS-AG-WF
has already been assigned to a
WiFi network.
Enter the password for the WiFi network access point, then confirm.
To check that your TEMPUS-AG-WF is correctly connected to the WiFi network, check that the LED on the front
panel is solid green.
Step 3
PAIRING
Association between a TEMPUS-AG device (CT/MS/PR/MV) and the TEMPUS-AG-WF:
You must first have associated your TEMPUS-AG device with your account in MyToroTempus application before
proceeding with the association of the device on your TEMPUS-AG-WF gateway. Refer to the device user
manual to associate it and then perform the following step.
1. Select the product in the
list of devices.
(Remember that you must be
connected to your device via
Bluetooth®).
Push on on the top
right of the screen to
access to information of
the products.
(Example refers to
TEMPUS-AG-CT)
TEMPUS-AG-WF
TEMPUS-AG-MS
TEMPUS-AG-MV
TEMPUS-AG-CT
TEMPUS-AG-4G
TEMPUS-AG-PR
TEMPUS-AG CT4
TEMPUS-AG S4
TEMPUS-AG-WF
TEMPUS-AG S1
SELECT A TEMP-AG-WF CONTROLLER
TEMPUS-AG-WF

Toro TEMPUS-AG-WF
5
2. Push on
« Remote access »
3. Select your
TEMPUS-AG-WF
(Refer to the «Default
name» present on its
product label)
4. Push on
Transmit to
validate the
operation.
5. Your TEMPUS-AG-WF
is now associated.
(Push red button to
test it)
Security key
The security key allows to protect your gateway. You can define it by clicking on the icon at the top right
of your screen (you must be connected via Bluetooth).

Toro TEMPUS-AG-WF
6
4. The message indicate
that the LoRaTM connection
between the TEMPUS-AG-WF
and the device is reliable.
3. Push the red
button to test the
connection LoRaTM
If the connection is not established, a "No connection established" message appears. Repeat this test several
times to confirm that the connection cannot be made. In this case, the distance between the TEMPUS-AG-WF
and the TEMPUS-AG device will need to be reduced.
1. Enter the TEMPUS-AG
device in Bluetooth® Then in the parameters
(small pencil at the top right) 2. Push on « Remote access »
Step 4
LoRaTM TEST CONNECTION
If the association of the devices is carried out before the final installation of the TEMPUS-AG-WF, this connection
test can be used to validate the positioning of the latter by going to temporarily install the TEMPUS-AG-WF in
its intended location then by going to position a device in each of the valve boxes to verify good communication
with the TEMPUS-AG-WF. The connection test can also allow you to verify at any time the correct operation of
the LoRaTM radio between your device and the TEMPUS-AG-WF.
(Example: the product fell into the upside-down valve box and no longer communicates with the TEMPUS-AG-
WF). To test the LoRaTM connection, do the following:
TEMPUS-AG CT4
TEMPUS-AG S4
TEMPUS-AG-WF
TEMPUS-AG S1

Toro TEMPUS-AG-WF
7
LED STATUS
INFORMATIONS ON THE STATUS OF THE TEMPUS-AG-WF LED
• Green LED: normal running
• Green LED flashing : Firmware update in progress
• Red LED flashing 3 times :
Possible causes :
1. Loss of Wi-Fi access point (router) or connection not etablished.
Restart your router and the product.
2. During initialization, the password entered is not correct.
Trick : Enter the password of the your router in a « Notes » application on your mobile. Copy the password
with a long press and paste it into the corresponding field. Repeat the initialization procedure.
3. During initialization, the product may be too far from the box : bring the product closer.
•Red LED flashing 2 times : alarm time : the TEMPUS-AG-WF is no longer on time. If your product is
connected to the MyToroTempusAG platform, the time setting will be automatic. Otherwise, connect to the
TEMPUS-AG-WF from the application and check that the message « Synchronization OK » is displayed.
•LED o : the product is not powered.
In the case of mounting the antenna outdoors with the optional extension of 10 meters, we recommend
protecting the antenna with a plastic tube with an internal diameter of 15mm minimum. This tube will be
clogged on his upper part to protect the antenna from the rain. The cord will have to be protected by a sheath.
MOUNTING (Outdoor Antenna)
Step 5
LoRaTM STATUS CONNECTION
The communication periodicity in LoRaTM mode :
The communication interval of the LoRaTM radio between the TEMPUS-AG devices and TEMPUS-AG-WF is
approximately 3 minutes.
Status of LoRaTM radio communication between the devices and the TEMPUS-AG-WF. The icons indicate
when TEMPUS-AG-WF was last connected to the device via LoRaTM. If you press the icon a message will inform
you of the last connection."
Last connection < 6 minutes
Connection never done or very long
time without communication with the
gateway.
Last connection >6 minutes
Changes not transmitted

Toro TEMPUS-AG-WF
8
This symbol indicates that the product uses a LoRaTM technology radio.
The symbol «CE» indicates that this device complies with the European standards on safety,
health, environment and user protection. Devices with the symbol «CE» are intended for sale in
Europe.
This symbol indicates that these types of electrical and electronic equipment must be disposed of
separately in European countries. Do not dispose of this device with your household waste.
Please use the collection and recycling points available in your Country when you no longer need
this device.
GENERAL INFORMATION
VI
In case of contrary use to the indications given in this user manual, the device protection may
be compromised.
This symbol indicates that the supply voltage is a direct voltage.
This symbol indicates that the supply voltage is an alternating voltage.
This symbol indicates the polarity of the DC supply voltage.
This symbol indicates that the power supply unit is intended for indoor use only.
This symbol indicates that the power supply unit is a double insulation class 2 type.
This symbol indicates that the eciency of the external power supply is level 6.

Toro TEMPUS-AG-WF
9
DECLARATION OF CONFORMITY
The Toro Company (Toro AG), 1588 N. Marshall Avenue, El Cajon, CA, 92020-1523, USA declare that TEMPUS-
AG-4G conform(s) to the following directives, standards and/or other normative documents:
CAN ICES-003B NMB-003B FCC Part 15B
Directive 2014/53/UE (RED)
Following standards:
BLE/WiFi standard : ETSI EN 300 328 v2.2.2
RADIO standard : ETSI EN 300 220-2 v3.1.1 & ETSI EN 300 220-1 v3.1.1
EMF standard : EN 62311 (2008) and the recommendation 1999/519/CE
EMC standard : EN 301 489-1 v.1.9.2 et EN 301 489-17 2.2.1
Safety standard : EN 62368-1:2014
RoHS Directive 2011/65/EU & Directive amendment (EU)2015/863
This declaration has been issued under the sole responsibility of the manufacturer. The object of the
declaration is in conformity with relevant union harmonization legislation.
TEMPUS-AG-WF
WiFi-LoRaTM Gateway
For Technical Assistance:
[email protected]
© 2021 The Toro Company
Toro ag
1588 N. Marshall Avenue, El Cajon, CA 92020-1523, USA

Toro TEMPUS-AG-WF
10
FCC/IC STATEMENT TEMPUS-AG-WF
This product contain a modular approval with FCC ID : YWW-BLEMOD, T9JRN2903, 2AC7Z-ESPWROOM02
and IC : 9319A-BLEMOD, 6514A-RN2903, 21098-ESPWROOM02.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions
: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Caution : the user that changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note : this equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction, may cause harmful
interference to radio communication. However, there is no guarantee that interference will not occurin a
particular installationi. If this equipment does cause harmful inteference to radio or television reception
which can be determined by tunning the equipment o and on ,the user is encouraged to try to correct
interference by one or more of the following measures :
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with innovation, science
and Economic development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions : (1) this device may not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
L’émetteur/recepteur exempt de license contenu dans le présent appareil est conforme aux CNR
d’innovation, Science et Dévellopement économique Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux condtions suivantes : (1) l’appareil ne doit pas produire de
brouillage, et (2) l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est suceptible d’en compromettre le fonctionnement.
This device complies with FCC and ISED RF radiation exposure limits set forth for general population.
This device must be installed to provide a separation distance of at least 20cm from all persons and
must not be co-located or operating in conjunction with any other antenna or transmitter.
Le present appareil est conforme aux niveaux limites d’exigences d’exposition RF aux personnes
définies par ISDE. L’appareil doit être installé afin d’orir une distance de séparation d’au moins 20cm
avec les personnes et ne doit pas être installé à proximité ou être utilisé en conjonction avec une autre
antenne ou un autre émetteur.
TEMPUS-AG-WF
WiFi-LoRaTM Gateway
For Technical Assistance:
[email protected] © 2021 The Toro Company
Toro ag
1588 N. Marshall Avenue, El Cajon, CA 92020-1523, USA