Toro groundmaster 7210 User manual

Form No. 3354-815 Rev B
Groundsmaster® 7200 and7210 Mower
Model No. 30360 —Serial No. 270000001 and Up
Model No. 30360TE —Serial No. 270000001 and Up
Model No. 30361 —Serial No. 270000001 and Up
Model No. 30362 —Serial No. 270000001 and Up
Model No. 30363 —Serial No. 270000001 and Up
Model No. 30363TC —Serial No. 270000001 and Up
Model No. 30363TE —Serial No. 270000001 and Up
Model No. 30364 —Serial No. 270000001 and Up
Model No. 30364TC —Serial No. 270000001 and Up
Model No. 30365 —Serial No. 270000001 and Up
Register your product at www.Toro.com Original Instructions (EN)

Warning
CALIFORNIA
Pr oposition 65 W ar ning
Diesel engine exhaust and some of its
constituents ar e kno wn to the State of
Calif or nia to cause cancer , bir th defects, and
other r epr oducti v e har m.
Because in some areas there are local, state , or
federal regulations requiring that a spark ar rester
be used on the engine of this mac hine , a spark
ar rester is a v ailable as an option. If y ou require a
spark ar restor , contact y our A uthorized Ser vice
Dealer .
Gen uine T oro spark ar resters are appro v ed b y the
USD A F orestr y Ser vice .
Important: It is a violation of Calif or nia
Public R esource Code Section 4442 to use
or operate the engine on an y f or est-co v er ed,
br ush-co v er ed, or g rass-co v er ed land without
a spar k ar r ester muf fler maintained in w or king
order , or the engine constricted, equipped, and
maintained f or the pr ev ention of fir e. Other
states or federal ar eas may ha v e similar la ws.
Introduction
R ead this infor mation carefully to lear n ho w to
operate and maintain y our product properly and
to a v oid injur y and product damag e . Y ou are
responsible for operating the product properly
and safely .
Y ou ma y contact T oro directly at www .T oro .com
for product and accessor y infor mation, help
finding a dealer , or to register y our product.
W henev er y ou need ser vice , g en uine T oro par ts ,
or additional infor mation, contact an A uthorized
Ser vice Dealer or T oro Customer Ser vice and ha v e
the model and serial n umbers of y our product
ready . Figure 1 identifies the location of the model
and serial n umbers on the product. W rite the
n umbers in the space pro vided.
Figure 1
1. Model and serial number location
Model No.
Serial No.
T his man ual identifies potential hazards and has
safety messag es identified b y the safety aler t
symbol ( Figure 2 ), whic h signals a hazard that ma y
cause serious injur y or death if y ou do not follo w
the recommended precautions .
Figure 2
1. Safety alert symbol
T his man ual also uses 2 w ords to highlight
infor mation. Impor tant calls attention to special
mec hanical infor mation and Note emphasizes
g eneral infor mation w or th y of special attention.
© 2006—The Toro® Company8111 Lyndale Avenue SouthBloomington, MN 55420
2
Contact us at www.Toro.com.
Printed in the USA.All Rights Reserved

Contents
Introduction .......................................................2
Safety ..................................................................5
Safe Operating Practices . . . . . . . . . . . . . . . . . . . . . . 5
T oro Riding Mo w er Safety . . . . . . . . . . . . . . . . . . . 6
Sound Pressure Lev el ...........................8
Sound P o w er Lev el ..............................8
Vibration Lev el ....................................8
Slope Char t ......................................... 9
Safety and Instr uctional
Decals .............................. 10
Setup ................................................................ 16
1 Installing the Left R ear Tire
(Model 30360TC and
30363TC Only) .................. 16
2 Acti v ating and Charging the
Batter y (Model 30360TC
and 30363TC Only) . . . . . . . . . . . 16
3 Adjusting the R OPS ........................ 18
4 Chec king the Tire Pressure . . . . . . . . . . . . . . 19
5 Installing W eights
(Groundsmaster 7210
Models in Europe
Only) ................................. 20
6 Chec king Fluid Lev els . . . . . . . . . . . . . . . . . . . . . 21
7 R eading the Man uals and Viewing
the D VD ........................... 21
Product Ov er view ............................................. 22
Controls ........................................... 22
Specifications ................................... 24
Operation .......................................................... 25
Adding Fuel ...................................... 25
Chec king the Engine Oil Lev el . . . . . . . . . . . 26
Chec king the Cooling System . . . . . . . . . . . . . 26
Chec king the Hy draulic
System ............................... 26
Using the R ollo v er Protection
System (R OPS) .................. 27
T hink Safety First .............................. 28
Operating the P arking Brak e . . . . . . . . . . . . . . 28
Star ting and Stopping the
Engine .............................. 29
Dri ving the Mac hine .......................... 30
Stopping the Mac hine ........................ 31
Operating the Mo w er ......................... 31
T he Safety Interloc k System . . . . . . . . . . . . . . . 35
P ositioning the Seat ........................... 36
Unlatc hing the Seat ............................ 37
Pushing the Mac hine b y Hand . . . . . . . . . . . . 37
Loading Mac hines ............................. 38
T ranspor ting Mac hines . . . . . . . . . . . . . . . . . . . . . . 39
Operating Tips .................................. 39
Maintenance ...................................................... 41
R ecommended Maintenance
Sc hedule(s) ............................... 41
Daily Maintenance Chec klist . . . . . . . . . . . . . . 42
Lubrication ................................................ 43
Greasing the Bearings and
Bushings ........................... 43
Ser vicing the Mo w er Dec k Gear
Bo x Lubricant ................... 45
Engine Maintenance .................................. 46
Air Cleaner Maintenance . . . . . . . . . . . . . . . . . . . 46
Ser vicing the Engine Oil . . . . . . . . . . . . . . . . . . . . 47
Fuel System Maintenance .......................... 49
Ser vicing the W ater Se parator . . . . . . . . . . . . 49
Cleaning the Fuel T ank . . . . . . . . . . . . . . . . . . . . . . 49
R e placing the Fuel Pre-Filter . . . . . . . . . . . . . . 49
Fuel Lines and Connections . . . . . . . . . . . . . . . 50
Bleeding the Fuel System . . . . . . . . . . . . . . . . . . . 50
Bleeding Air F rom the
Injectors ............................ 51
Electrical System Maintenance . . . . . . . . . . . . . . . . . . . 51
Ser vicing the Batter y .......................... 51
Storing the Batter y ............................. 52
Chec king the Fuses ............................ 52
Dri v e System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 52
Chec king the Tire Pressure . . . . . . . . . . . . . . . . . 52
R e placing the Castor W heels and
Bearings ............................ 53
Cooling System Maintenance . . . . . . . . . . . . . . . . . . . . . 53
Chec king the Cooling System . . . . . . . . . . . . 54
Cleaning the Radiator ........................ 54
Brak e Maintenance .................................... 55
Adjusting the P arking Brak e
Interloc k Switc h . . . . . . . . . . . . . . . . 55
Belt Maintenance ....................................... 55
Chec king the Alter nator Belt . . . . . . . . . . . . . 55
R e placing the Blade Dri v e
Belts .................................. 56
Controls System Maintenance . . . . . . . . . . . . . . . . . . . . 56
Adjusting the Control Lev er
Neutral Interloc k
Switc h ............................... 56
Adjusting the Control Lev er
Neutral R etur n .................. 57
Adjusting the T raction Dri v e for
Neutral .............................. 58
Adjusting the Maxim um Ground
Speed ................................ 59
Adjusting the T rac king . . . . . . . . . . . . . . . . . . . . . . . 60
3

Hy draulic System Maintenance . . . . . . . . . . . . . . . . . . 61
Chec king the Hy draulic
System ............................... 61
Changing the Hy draulic Oil And
Filter ................................. 62
Mo w er Dec k Maintenance ......................... 62
Ser vicing the Cutting Blades . . . . . . . . . . . . . . . 63
Cor recting Mo w er Dec k
Mismatc h .......................... 66
Adjusting the Mo w er Dec k
Pitc h .................................. 66
R e placing the Grass Deflector . . . . . . . . . . . . 67
Cleaning .................................................... 67
Cleaning Under the Mo w er . . . . . . . . . . . . . . . . 67
W aste Disposal .................................. 68
Storag e .............................................................. 69
Mac hine ............................................ 69
Engine .............................................. 69
Sc hematics ........................................................ 70
4

Safety
Mac hines with model n umbers 30360TC ,
30360TE, 30361, 30362, 30363TC , 30363TE,
30364, or 30365 meet or ex ceed CEN standard
EN 836:1997 and ANSI B71.4-2004 specifications
in effect at the time of production. Mac hines with
model n umbers 30360 or 30363 meet or ex ceed
ANSI B71.4-2004 specifications in effect at the
time of production.
Improper use or maintenance b y the operator
or o wner can result in injur y . T o reduce the
potential for injur y , comply with these safety
instr uctions and alw a ys pa y attention to the safety
aler t symbol, whic h means Caution, W ar ning , or
Danger —personal safety instr uction. F ailure to
comply with the instr uction ma y result in personal
injur y or death.
Safe Operating Practices
T he follo wing instr uctions are from the CEN
standard EN 836:1997 and ANSI B71.4-2004.
T his product is capable of amputating hands and
feet and thro wing objects . Alw a ys follo w all safety
instr uctions to a v oid serious injur y or death.
Training
•R ead the Operator’ s Manual and other training
material carefully . Be familiar with the
controls , safety signs , and the proper use of the
equipment.
•Nev er allo w c hildren or people unfamiliar with
these instr uctions to use the la wn mo w er .
Local regulations can restrict the ag e of the
operator .
•Nev er mo w while people , especially c hildren,
or pets are nearb y .
•K ee p in mind that the operator or user is
responsible for accidents or hazards occur ring
to other people or their proper ty .
•Do not car r y passeng ers .
•All dri v ers should seek and obtain professional
and practical instr uction. Suc h instr uction
should emphasize:
– the need for care and concentration when
w orking with ride-on mac hines;
– control of a ride-on mac hine sliding on a
slope will not be reg ained b y the application
of the control lev ers . T he main reasons for
loss of control are:
◊ insufficient wheel g rip , especially on
w et g rass;
◊ being dri v en too fast;
◊ inadequate braking;
◊ the type of mac hine is unsuitable for its
task;
◊ lac k of a w areness of the effect of
g round conditions , especially slopes;
◊ incor rect load distribution.
Preparation
•W hile mo wing, alw a ys w ear substantial
footw ear and long trousers . Do not operate
the equipment when barefoot or w earing open
sandals .
•T horoughly inspect the area where the
equipment is to be used and remo v e all objects
whic h ma y be thro wn b y the mac hine .
• W ar ning —fuel is highly flammable .
– Store fuel in containers specifically designed
for this pur pose .
– R efuel outdoors only and do not smok e
while refueling .
– Add fuel before star ting the engine . Nev er
remo v e the cap of the fuel tank or add fuel
while the engine is r unning or when the
engine is hot.
– If fuel is spilled, do not attempt to star t the
engine but mo v e the mac hine a w a y from
the area of spillag e and a v oid creating any
source of ignition until fuel v apors ha v e
dissipated.
– R e place all fuel tank and container caps
securely .
•R e place faulty silencers/m ufflers .
•Before using, alw a ys visually inspect to see that
the blades , blade bolts and cutter assembly
are not w or n or damag ed. R e place w or n or
damag ed blades and bolts in sets to preser v e
balance .
•On m ulti-bladed mac hines , tak e care as rotating
one blade can cause other blades to rotate .
5

Operation
•Be aler t, slo w do wn and use caution when
making tur ns . Look behind and to the side
before c hanging directions .
•Do not operate the engine in a confined space
where dang erous carbon mono xide fumes can
collect.
•Mo w only in da ylight or in g ood ar tificial light.
•Before attempting to star t the engine ,
diseng ag e all blade attac hment clutc hes and
shift into neutral.
•R emember there is no suc h thing as a safe
slope . T ra v el on g rass slopes requires par ticular
care . T o guard ag ainst o v er tur ning:
– do not stop or star t suddenly when on a
slope;
– use slo w speeds on slopes and during tight
tur ns;
– sta y aler t for humps and hollo ws and other
hidden hazards;
•W atc h out for traffic when crossing or near
roadw a ys .
•Stop the blades from rotating before crossing
surfaces other than g rass .
•W hen using any attac hments , nev er direct
disc harg e of material to w ard b ystanders
nor allo w any one near the mac hine while in
operation.
•Nev er operate the mac hine with damag ed
guards , shields , or without safety protecti v e
devices in place .
•Do not c hang e the engine g o v er nor settings or
o v erspeed the engine . Operating the engine
at ex cessi v e speed ma y increase the hazard of
personal injur y .
•Before lea ving the operator’ s position:
– diseng ag e the po w er tak e-off and lo w er the
attac hments;
– c hang e into neutral and set the parking
brak e;
– stop the engine and remo v e the k ey .
•Diseng ag e dri v e to attac hments , stop the
engine , and remo v e the ignition k ey:
– before clearing bloc kag es or unclog ging
c hute;
– before c hec king, cleaning or w orking on
the la wn mo w er;
– after striking a foreign object. Inspect
the la wn mo w er for damag e and mak e
re pairs before restar ting and operating the
equipment;
– if the mac hine star ts to vibrate abnor mally
(c hec k immediately).
•Diseng ag e dri v e to attac hments when
transpor ting or not in use .
•Stop the engine and diseng ag e dri v e to
attac hment before refuelling .
Maintenance and Storage
•K ee p all n uts , bolts and screws tight to be sure
the equipment is in safe w orking condition.
•Nev er store the equipment with fuel in the
tank inside a building where fumes ma y reac h
an open flame or spark.
•Allo w the engine to cool before storing in any
enclosure .
•T o reduce the fire hazard, k ee p the engine ,
silencer/m uffler , batter y compar tment and fuel
storag e area free of g rass , lea v es , or ex cessi v e
g rease .
•R e place w or n or damag ed par ts for safety .
•If the fuel tank has to be drained, do this
outdoors .
•On m ulti-bladed mo w ers , tak e care as man ually
rotating one blade can cause other blades to
rotate .
•W hen mac hine is to be park ed, stored or left
unattended, lo w er the mo w er dec k.
Toro Riding Mower Safety
T he follo wing list contains safety infor mation
specific to T oro products or other safety
infor mation that y ou m ust kno w that is not
included in the CEN standard.
•Engine exhaust contains carbon mono xide ,
whic h is an odorless , deadly poison that can
kill y ou. Do not r un engine indoors or in an
enclosed area.
•K ee p hands , feet, hair and loose clothing a w a y
from attac hment disc harg e area, underside of
mo w er and any mo ving par ts while engine is
r unning .
•Do not touc h equipment or attac hment par ts
whic h ma y be hot from operation. Allo w to
6

cool before attempting to maintain, adjust, or
ser vice .
•Batter y acid is poisonous and can cause bur ns .
A v oid contact with skin, eyes and clothing .
Protect y our face , eyes , and clothing when
w orking with a batter y .
•T his mac hine is not designed or equipped for
on-road use and is a “slo w-mo ving v ehicle . ”
If y ou m ust cross or tra v el on a public road,
y ou should be a w are of and comply with
local regulations , suc h as required lights , slo w
mo ving v ehicle signs , and reflectors .
•Batter y g ases can explode . K ee p cig arettes ,
sparks and flames a w a y from batter y .
•Use only g en uine T oro re placement par ts to
ensure that original standards are maintained.
•Use only T oro appro v ed attac hments .
W ar ranty ma y be v oided if used with
unappro v ed attac hments .
Slope Operation
•Do not mo w near drop-offs , ditc hes , stee p
banks or w ater . W heels dropping o v er edg es
can cause rollo v ers , whic h ma y result in serious
injur y , death, or dro wning .
•Do not mo w slopes when g rass is w et. Slipper y
conditions reduce traction and could cause
sliding and loss of control.
•Do not mak e sudden tur ns or rapid speed
c hang es .
•Use a w alk behind mo w er and/or a hand
trimmer near drop-offs , ditc hes , stee p banks
or w ater .
•R educe speed and use extreme caution on
slopes .
•R emo v e or mark obstacles suc h as roc ks , tree
limbs , etc . from the mo wing area. T all g rass
can hide obstacles .
•W atc h for ditc hes , holes , roc ks , dips , and rises
that c hang e the operating angle , as rough
ter rain could o v er tur n the mac hine .
•A v oid sudden star ts when mo wing uphill
because the mo w er ma y tip bac kw ards .
•Be a w are that loss of traction ma y occur g oing
do wnhill. W eight transfer to the front wheels
ma y cause dri v e wheels to slip and cause loss
of braking and steering .
•Alw a ys a v oid sudden star ting or stopping on
a slope . If tires lose traction, diseng ag e the
blades and proceed slo wly off the slope .
•F ollo w the man ufacturer’ s recommendations
for wheel w eights or counterw eights to
impro v e stability .
•Use extreme care with attac hments . T hese can
c hang e the stability of the mac hine and cause
loss of control.
Using the Rollover Protection System(ROPS)
•K ee p the roll bar in the raised and loc k ed
position and use the seat belt when operating
the mac hine .
•Be cer tain that the seat belt can be released
quic kly in the ev ent of an emerg ency .
•Be a w are there is no rollo v er protection when
the roll bar is do wn.
•Chec k the area to be mo w ed and nev er fold
the R OPS in areas where there are slopes , drop
offs or w ater .
•Lo w er the rollbar only when absolutely
necessar y . Do not w ear the seat belt with
the r oll bar f olded do wn.
•Chec k carefully for o v erhead clearances (i.e .
branc hes , doorw a ys , electrical wires) before
dri ving under any objects and do not contact
them.
7

Sound Pressure Level
Note: T he data contained in this section only
per tains to units mark ed with the CE log o ( ).
T his unit has an equi v alent contin uous A-w eighted
sound pressure lev el at the operator ear of 90 dB A,
based on measurements of identical mac hines per
EN 11201.
Sound Power Level
Note: T he data contained in this section only
per tains to units mark ed with the CE log o ( ).
T his unit has a guaranteed sound po w er lev el of
105 dB A, based on measurements of identical
mac hines per EN 11094.
Vibration Level
Hand-Arm
T his unit does not ex ceed a hand/ar m vibration
lev el of 2.5 m/s
2
, based on measurements of
identical mac hines per EN 1033.
Whole Body
T his unit does not ex ceed a whole body vibration
lev el of 0.5 m/s
2
, based on measurements of
identical mac hines per EN 1032.
8

Slope Chart
9

Safety and Instructional
Decals
Safety decals and instr uctions are easily visible to the operator and are located near any
area of potential dang er . R e place any decal that is damag ed or lost.
112-1461
1. Belt routing
107-2908
1. Thrown object hazard—keep bystanders a safe distance fromthe machine.
2. Thrown object hazard—do not operate the mower with thedeector up or removed, keep the deector in place.3. Cutting/dismemberment hazard of hand or foot, mowerblade—stay away from moving parts.
110-9772
1. Warning—read the Operator’s Manual and receive training.
8. Warning—engage the parking brake, stop the engine andremove the ignition key before leaving the machine.2. Crushing/dismemberment hazard of bystanders—do not carrypassengers, keep bystanders a safe distance from the machine.
9. Cutting hazard of hand or foot—remove the ignition keyand read the instructions before servicing or performingmaintenance, keep away from moving parts.3. Warning—do not use drugs or alcohol. 10. Thrown object hazard—keep bystanders a safe distance fromthe machine; keep all deectors and shields in place.4. Warning—wear hearing protection.
11. Disengage5. Tipping, drop off hazard—do not operate near water drop-offs,stay a safe distance from drop-offs, slow machine beforeturning, do not turn at high speeds, wear a seat belt when aROPS is in place, do not wear a seat belt when ROPS is lowered.
12. Engage
6. To start the engine: clear any debris from mower belt,disengage the PTO, move the motion control levers to theneutral position, engage the parking brake, turn the ignitionto Run and wait for the glow plug light to turn off, turn theignition key to Start. 13. Parking brake
7. Read the Operator’s Manual.
10

110-8253
1. PTO–Off 4. Continuous variable setting2. PTO—On
5. Slow3. Fast
110-8254
1. Engine–Stop 3. Engine—Start2. Engine—Run
110-9796
1. Read the Operator’s Manual for information on fuses.
110-8252
1. Read the Operator’s Manual.
3. Hydraulic oil 5. Engine coolant2. Parking brake 4. Fuel 6. Engine oil
11

110-9774
1. Forward 3. Slow
5. Reverse
7. Tow valve location; torquethe tow valves to 6.78 ± 1.13N⋅m (60 ± 10 in-lbs).2. Fast
4. Neutral 6. Backward
8. Read the Operator’s Manualfor more information on thehydraulic oil.
93-7818
1. Warning—read the Operator’s Manual for instructions ontorquing the blade bolt/nut to 115-149 N•m (85-110 ft-lb).
93-6696
1. Stored energy hazard—read the Operator’s Manual .
93-6687
1. Do not step here.
93-6697
1. Read the Operator’s
Manual .
2. Check the oil every 50hours. Add SAE 80w-90(API GL-5) oil if needed.
100-6578
1. Entanglement hazard, belt—do not operate the machinewith the shields or guards removed; always keep the shieldsand guards in place; stay away from moving parts.
106-6753
1. Thrown object hazard—keep bystanders a safe distance fromthe machine.
2. Cutting/dismemberment hazard of hand or foot, mowerblade—stay away from moving parts.
12

106-6755
1. Engine coolant underpressure. 3. Warning—do not touch thehot surface.2. Explosion hazard—read theOperator’s Manual.
4. Warning—read theOperator’s Manual.
106-9206
1. Wheel torque specications2. Read the Operator’s Manual .
107-3069
1. Warning—there is no rollover protection when the roll bar isdown.
2. To avoid injury or death from a rollover accident, keep theroll bar in the raised and locked position and wear the seatbelt. Lower the roll bar only when absolutely necessary; donot wear the seat belt when the roll bar is down.3. Read the Operator’s Manual ; drive slowly and carefully.
107-2916
Side Discharge Models Only
1. Remove the ignition key and read theOperator’s Manual before servicing orperforming maintenance. 2. Thrown object hazard—do not operatethe mower with the deector up orremoved, keep the deector in place;keep bystanders a safe distance fromthe machine. 3. Cutting/dismemberment hazard ofhand or foot, mower blade—stay awayfrom moving parts.
13

106-9290
1. Inputs 5. In seat
9. Outputs 13. Start2. (not active on this machine) 6. Power Take-off (PTO) 10. Power Take-off (PTO)
14. Power3. High temperature shutdown 7. Parking brake Off
11. Start4. High temperature warning 8. Neutral
12. Energize to Run (ETR)
110-9781
1. Warning—read the Operator’s Manual.2. Poison and caustic liquid/chemical burn hazard—keep children a safe distance from the battery.3. Warning—do not touch the hot surface.4. Cutting/dismemberment hazard, fan and entanglement hazard, belt—stay away from moving parts.5. Hydraulic oil in system under pressure, escaping hydraulic oil penetrating skin hazard, broken hydraulic lines hazard—wearprotective hand protection when handling hydraulic system components.
106-6754
CE Marked Models Only (With the CE Kit Installed)
1. Warning—do not touch the hot surface.2. Cutting/dismemberment hazard, fan and entanglementhazard, belt—stay away from moving parts.
112-1689
CE Marked Models Only (With the CE Kit Installed)* T h i s s a f e t y d e c a l i n c l u d e s a s l o p e w a r n i n g r e q u i r e d o n t h e m a c h i n e f o r
c o m p l i a n c e t o t h e E u r o p e a n L a w n M o w e r S a f e t y S t a n d a r d E N 8 3 6 : 1 9 9 7 .
T h e c o n s e r v a t i v e m a x i m u m s l o p e a n g l e s i n d i c a t e d f o r o p e r a t i o n o f t h i s
m a c h i n e a r e p r e s c r i b e d b y a n d r e q u i r e d b y t h i s s t a n d a r d .
1. Tipping hazard—do not operate on slopes greater than 14degrees.
14

107-1866
1. Sliding and loss of control hazard and tipping hazard,drop-offs—do not operate the machine near drop-offs,slopes greater than 15 degrees, or water; keep a safedistance from drop-offs; do not turn sharply while travelingfast, instead, slow down and turn gradually; if the roll bar israised, wear the seat belt; if the roll bar is lowered, do notwear the seat belt.
Manufacturer’s Mark
1. Indicates the blade is identied as a part from the originalmachine manufacturer.
Battery Symbols
Some or all of these symbols are on your battery
1. Explosion hazard 6. Keep bystanders a safedistance from the battery.2. No re, open ame, orsmoking.
7. Wear eye protection;
explosive gases can causeblindness and other injuries3. Caustic liquid/chemical
burn hazard
8. Battery acid can causeblindness or severe burns.4. Wear eye protection
9. Flush eyes immediately
with water and get medicalhelp fast.5. Read the Operator’s
Manual.
10. Contains lead; do notdiscard.
15

Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Step
Description
Qty.
Use
Tire
11
Lug nut 5
Install the left rear tire (model30360TC and 30363TC only).
2
No parts required
–
Activate and charge the battery(model 30360TC and 30363TConly).
3
No parts required
–
Adjust the ROPS.
4
No parts required
–
Check the tire pressure.
5
No parts required
–
Install weights.
6
No parts required
–
Check the hydraulic uid, engineoil, and coolant levels.
Operator’s Manual
1
Engine Operator’s Manual
1
Parts Catalog
1
Operator Training DVD
1
Pre-delivery Inspection Sheet
1
Engine warranty
1
CE certicate
1
7
Certicate of Quality
1
Read the manuals and watch theDVD before operating the machine.Use the remaining parts for theinstallation of attachments.
Step
1
Installing the Left RearTire (Model 30360TC and30363TC Only)
Parts needed for this step:
1
Tire
5 Lug nut
Procedure
1. Suppor t the left rear of the mac hine with jac k
stands .
2. R emo v e the lug n uts from the tire mounting
studs .
3. Pull the crate and brac k et off of the wheel hub .
4. Install the rear tire onto the hub and secure it
using the lug n uts remo v ed previously .
5. T or que the lug n uts to 75 to 80 ft-lb (102 to
108 N ⋅m).
16

Step
2
Activating and Chargingthe Battery (Model 30360TCand 30363TC Only)
No Parts Required
Procedure
Use only electrolyte (1.265 Specific Gra vity) to fill
batter y initially .
1. R emo v e the batter y from the mac hine .
Important: Do not add electr ol yte while
the batter y is in the machine. Y ou could
spill it, causing cor r osion.
2. Clean the top of the batter y and remo v e the
v ent caps ( Figure 3 ).
Figure 3
1. Vent caps
3. Carefully fill eac h cell with electrolyte until the
plates are co v ered with about 1/4 inc h (6 mm)
of fluid ( Figure 4 ).
Figure 4
1. Electrolyte
4. Allo w appro ximately 20 to 30 min utes for the
electrolyte to soak into the plates . R efill as
necessar y to bring the electrolyte to within
about 1/4 inc h (6 mm) of the bottom of the
fill w ell ( Figure 4 ).
Charging the batter y pr oduces gasses
that can explode.
Nev er smok e near the batter y and k eep
spar ks and flames a w ay fr om batter y .
5. Connect a 3 to 4 amp batter y c harg er to the
batter y posts . Charg e the batter y at a rate of
3 to 4 amps until the specific g ra vity is 1.250
or higher and the temperature is at least 60°F .
(16°C) with all cells g asing freely .
6. W hen the batter y is c harg ed, disconnect the
c harg er from the electrical outlet and batter y
posts .
Note: After the batter y has been acti v ated,
add only distilled w ater to re place nor mal loss ,
although maintenance-free batteries should
not require w ater under nor mal operating
conditions .
17

Warning
CALIFORNIA
Pr oposition 65 W ar ning
Batter y posts, ter minals, and r elated
accessories contain lead and lead
compounds, chemicals kno wn to the
State of Calif or nia to cause cancer and
r epr oducti v e har m. W ash hands after
handling .
Batter y ter minals or metal tools could
shor t a gainst metal tractor components
causing spar ks. Spar ks can cause the
batter y gasses to explode, r esulting in
per sonal injur y .
• W hen r emo ving or installing the
batter y , do not allo w the batter y
ter minals to touch an y metal par ts of
the tractor .
• Do not allo w metal tools to shor t
betw een the batter y ter minals and
metal par ts of the tractor .
7. Install the batter y into the mac hine and secure
it.
Important: T he batter y must not be a ble
to mo v e or wig g le when pushed.
8. First, install the positi v e cable (red) to the
positi v e (+) ter minal and then the neg ati v e
cable (blac k) to the neg ati v e (-) ter minal of
the batter y . Slide the r ubber boot o v er the
positi v e ter minal to prev ent a possible shor t
from occur ring .
Incor r ect batter y ca ble r outing could
dama ge the machine and ca bles causing
spar ks. Spar ks can cause the batter y
gasses to explode, r esulting in per sonal
injur y .
• Al w ays disconnect the negati v e
(black) batter y ca ble bef or e
disconnecting the positi v e (r ed)
ca ble.
• Al w ays connect the positi v e (r ed)
batter y ca ble bef or e connecting the
negati v e (black) ca ble.
Connecting ca bles to the wr ong post
could dama ge the electrical system and
r esult in per sonal injur y .
Note: Ensure that the batter y cables are
routed a w a y from any shar p edg es or mo ving
par ts .
Step
3
Adjusting the ROPS
No Parts Required
Procedure
1. R emo v e the hair pin cotter pins and remo v e the
tw o pins from the roll bar ( Figure 5 ).
18

Figure 5
Right Side Shown
1. Roll bar
3. Hairpin cotter pin2. Pin
2. Raise the roll bar to the upright position and
install the tw o pins and secure them with the
hair pin cotter pins ( Figure 5 ).
Note: If y ou m ust lo w er the roll bar , push
the bar forw ard to reliev e pressure on the
pins , remo v e the pins , lo w er the bar slo wly ,
and secure it with the pins so that it does not
damag e the hood.
Step
4
Checking the Tire Pressure
No Parts Required
Procedure
T he tires are o v er inflated for shipping . T herefore ,
release some of the air to reduce the pressure . T he
cor rect air pressure is 15 psi (103 kP a) in the rear
tires and 25 psi (172 kP a) in the caster wheels .
19

Step
5
Installing Weights (Groundsmaster 7210 Models in EuropeOnly)
No Parts Required
Procedure
T he Groundsmaster 7210 mac hine does not need added w eight to meet CE standards so long as there are
no attac hments added to it. Ho w ev er , y ou ma y need to purc hase and install additional w eight de pending
on mo w er dec k size/type and the attac hments y ou install on the mac hine . T he follo wing table lists the
v arious attac hment configurations and the additional front w eight needed for eac h model:
Note: T he Groundsmaster 7200 mac hine does not need w eight in any configuration to meet the CE
standards .
Attachment
Conguration
Weight Required witha 62 inch (157.5 cm)Guardian Mower Weight Required witha 72 inch (183 cm)Guardian Mower Weight Required witha 72 inch (183 cm)Side-discharge Mower
Groundsmaster 7210Traction Unit with noAdded Attachments
22 lb (10 kg) 0 lb (0 kg) 0 lb (0 kg)
Groundsmaster 7210Traction Unit and HardCanopy
75 lb (34 kg) 21 lb (9.5 kg) 33 lb (15 kg)
Groundsmaster 7210Traction Unit, Hard Canopy,and Road Light Kit
71 lb (32.2 kg) 63 lb (28.5 kg) 22 lb (10 kg)
Groundsmaster 7210Traction Unit, Hard Canopy,Road Light Kit, and JackStand
40 lb (18 kg) 37 lb (17 kg) 22 lb (10 kg)
Groundsmaster 7210Traction Unit, Hard Canopy,and Jack Stand
31 lb (14 kg) 22 lb (10 kg) 22 lb (10 kg)
Groundsmaster 7210Traction Unit, Road LightKit, and Jack Stand
0 lb (0 kg) 0 lb (0 kg) 0 lb (0 kg)
Groundsmaster 7210Traction Unit and RoadLight Kit
25 lb (11.3 kg) 0 lb (0 kg) 0 lb (0 kg)
Groundsmaster 7210Traction Unit and Jack Stand
0 lb (0 kg) 0 lb (0 kg) 0 lb (0 kg)
Contact y our A uthorized T oro Distributor to obtain the appropriate kits and w eights for y our mac hine .
20