Toro TITAN series Manual

FormNo.3382-315RevA
TITAN®RidingMower
ModelNo.Allmodels
SetupInstructions
Setup
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
1Nopartsrequired–Connectthebattery.
Rearhitch1
Bolt(5/16x2-1/2inches)2
2Locknut(5/16inch)2
Installtherearhitch.
3Nopartsrequired–Setupthemotion-controllevers.
4Nopartsrequired–SetuptheRolloverProtectionSystem
(ROPS)bar.
5Nopartsrequired–Checkthemoweradjustment.
Ignitionkey1
Hosecoupling(notincludedwithCE
models)1
Operator'sManual1
EngineOperator'sManual1
6
Operatortrainingmaterial1
Completethesetup.
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
©2013—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA.
AllRightsReserved*3382-315*A

1
ConnectingtheBattery
NoPartsRequired
Procedure
1.Locatethebatteryandnegativebatterycable.
2.Removetheplasticcapfromthenegativebatterypost.
3.Removethefastenersonthenegativebatterycable,
andusethemtosecurethenegativebatterycableto
thenegativebatterypost(Figure1).
G018395
2
1
4
3
6
5
Figure1
1.Negativebatterycable4.Negativebatterypostcap
2.Wingnut5.Carriagebolt
3.Washer6.Negativebatterypost
2
InstallingtheRearHitch
Partsneededforthisprocedure:
1Rearhitch
2Bolt(5/16x2-1/2inches)
2Locknut(5/16inch)
Procedure
InstallthebrackettotheframeasshowninFigure2and
Figure3.
g015397
1
2
Figure2
Beforeassembly
1.Bolts2.Locknuts
Figure3
Afterassembly
2

3
SettinguptheMotion-control
Levers
NoPartsRequired
Procedure
1.Locatethemotion-controlleversattached,butfolded
downonthemachine.
2.Removetheupperbolt(3/8x1inch)andwasher;
loosenthelowerbolt(3/8x1inch).
3.Raisethemotioncontrolleverstotheuprightposition.
4.Aligntheholesinthemotion-controlleverwiththe
holesinthecontrol-armshaft,andinstallthebolt
andwasherremovedpreviously.Repeatthisforboth
controlslevers.
Note:Handtightenallfasteners.
5.Movethemotion-controlleverstotheparkposition,
raisetheseat,andmovethecontrolleversbacktothe
centerposition(neutral).
6.Verifythatthemotion-controlleversareproperly
aligned.
Note:Adjustasnecessary.Tightenallfasteners.
4
SettinguptheRollover
ProtectionSystem(ROPS)Bar
NoPartsRequired
Procedure
1.Removethebolts(1/2x3inches),washers,andnuts
fromthemiddleholeontheROPSplate(Figure4).
Figure4
Leftsideshown;repeatontherightside
1.Washer3.Middlehole
2.Bolt(1/2x3inches)4.Nut
2.RotatetheROPStotheuprightposition.
3.Installthebolts(1/2x3inches),washers,andnuts
removedpreviouslyintothemiddlehole(Figure4).
4.Removethebolts(1/2x3inches),washers,andnuts
fromthefourthholeintheROPSplate(Figure5).
3

Figure5
Leftsideshown;repeatontherightside
1.Washer3.Fourthhole
2.Bolt(1/2x3inches)4.Nut
5.Installtheremovedbolts(1/2x3inches),washers,and
nutsintothelowestholeintheROPSplate(Figure6).
Figure6
Leftsideshown;repeatontherightside
1.Washer3.Lowesthole
2.Bolt(1/2x3inches)4.Nut
6.Torqueallofthefastenerstoapproximately45N-m
(400in-lbs).
5
CheckingtheMower
Adjustment
NoPartsRequired
Procedure
Adjusttheside-to-sidelevelandthefront-to-rearbladeslope.
UsetherelevantproceduresintheOperator'sManualtoverify
thatthedeckislevel,andmakeanyadjustmentsasnecessary.
RefertotheOperator'sManualformoreinformation.
6
CompletingtheSetup
Partsneededforthisprocedure:
1Ignitionkey
1Hosecoupling(notincludedwithCEmodels)
1Operator'sManual
1EngineOperator'sManual
1Operatortrainingmaterial
Procedure
CheckingtheTirePressure
Checkthefrontandreartiresforproperination;referto
CheckingtheTirePressureintheOperator'sManualforthe
recommendedinationpressure.
CheckingtheSide-DischargeChute
Removethepackingrestraintholdingthesidedischargechute
upandlowerthechuteintoplace.
CheckingtheEngine-OilLevel
Beforeyoustarttheengineandusethemachine,checkthe
oillevelintheenginecrankcase;refertoCheckingtheOil
LevelintheOperator'sManual.
Keepallthefollowingitemswiththemachine:
•Ignitionkey
•Hosecoupling(notincludedinCEmodels)
•Operator'sManual
•EngineOperator'sManual
•ViewtheOperatortrainingmaterialbeforeoperatingthe
machine.
4