Toro 93-3903 User manual

All Rights Reserved
Printed in the USA
1
2002 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
Work Light Kit
Workman3000 Series
Part No. 93-3903
Form No. 3316-907 Rev A
Installation Instructions
Installation
Note: The vehicle must be equipped with a Wire Harness Kit,
Part No. 93-3900, before the Work Light Kit can be installed.
1. Raise the bed and install the safety support on the fully
extended lift cylinder rod (if so equipped).
2. Stop the engine, set the parking brake, and remove the
key from the ignition switch.
3. Remove the positive (+) battery cable from the battery.
4. Remove the front hood from the vehicle if it is not
already removed; refer to the wire harness Installation
Instructions.
5. Plug the spade terminal of the red wire from the light
kit harness into the new fuse block. Affix the fuse decal
to the corresponding circuit on the vehicle fuse block
decal (Fig. 1).
6. Insert a 15 amp fuse into the fuse block at the location
shown on the decal (Fig. 1).
1
2
3
Figure 1
1. Fuse block
2. Fuse decals 3. 15 amp fuse
7. Affix the work light switch decal around 2 of the
mounting holes in the switch bracket (Fig. 2).
8. Mount each work light switch in the hole of the switch
bracket with a washer and 2 hex nuts (Fig. 2). Position
the washer between the top nut and switch bracket.
9. Remove the protective coverings from the terminals of
the brown/white and red wires from the wiring harness.
Secure the terminals to the front work light switch with
2 screws and washers (Fig. 2).
10.Remove the protective coverings from the terminals of
the blue and red wires from the wiring harness. Secure
the terminals to ther rear work light switch with 2
screws and washers (Fig. 2).
1
2
3
Figure 2
1. Decal
2. Switch bracket 3. Switch
11. Using the locations shown in Figure 3, loosely mount
each work light to the work light bracket with a stop
tab, 2 Belleville washers, and a nut. Point the outside
light forward (Fig. 3).
1
3
4
5
2
Figure 3
1. Work light
2. Work light bracket
3. Stop tab
4. Belleville washers (2)
5. Nut
Note: If you are mounting a Signal Light Kit, Part No.
93-3901, do so per the instructions supplied with the kit
before installing the light channels.

2
12.Mount the work light bracket to the end holes of the
light channels with 2 capscrews (5/16 x 3/4 in.), flat
washers, and locknuts (Fig. 3).
13.Plug the ROPS harness connectors into the appropriate
light connectors. The brown/white wire is for the front
lights; the blue wire is for the rear light.
14.Mount the light channels to the ROPS as instructed in
the wire harness Installation Instructions.
15.Connect the positive (+) battery cable to the battery.
Operation
To operate the work lights, move the toggle switches to the
On position.
Schematic
+12 VDC HEADLIGHT
SWITCH
EXISTING
BLUE
+12 VDC
EXISTING
BRAKE SWITCH
GRAY/ BLACK GRAY/
BLACK
SIGNAL FLASHER
GREEN
GREEN YELLOW
PINK
BLACK
BLACK
BLACK
BLACK
BLACKBLACK
PINK
BLUE
BROWN/WHITE
RED
RED
REVERSE SWITCH
AUDIO
RED
REAR LAMP SWITCH
FRONT LAMP SWITCH
BROWN/WHITE
BROWN/WHITE
WARNING LIGHT SWITCH
WARNING LIGHT FLASHER
WARNING LIGHT
WARNING LIGHT
YELLOW
YELLOWYELLOWORANGE
+12 VDC
YELLOW
BLACK
RED
VIOLET
GREEN
SIGNAL FLASHER BRAKE SWITCH
RIGHT
FRONT
LEFT
FRONT
RELAY
LEFT REAR
RIGHT REAR
WHITE
GRAY
BLACK
LOW
HIGH
WHITE/GREEN
YELLOW/BLACK
AUX HEAD LIGHTS
WHITE/GREEN
YELLOW/BLACK
TRAILER PLUG
BLACK WHITE
GREEN
YELLOW
BROWN
GRAY
VIOLET
BLACK
BLACK BLACK
BLACK
WHITE/BLACK
WHITE/BLACK
VIOLET
VIOLET
GRAY
RH ROPS SIGNAL LH ROPS SIGNAL
GRAY
GRAY
GRAY
VIOLET
VIOLET
WHITE/BLACK
WHITE/BLACK
LH FRONT SIGNALS
RH FRONT SIGNALS
BLACK
BLACK
VIOLET
VIOLET
GREEN
RED
VIOLET
VIOLET
RH TAIL LIGHTS LH TAIL
LIGHTS
G
S
ILT
EXISTING
ORANGE
FUEL GAGE