TaoTronics TT-DL095 User manual
Model: TT-DL095
TaoTronics LED Floor Lamp
User Guide
E-mail
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology Development Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II, Shenzhen, China
www.taotronics.com
Made in China TT-DL095_V1.2_EN
01 ENGLISH ENGLISH 02
Thanks for choosing TaoTronics LED Floor Lamp. Please read this User Guide thoroughly before use
and retain it for future reference.
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS. KEEP
FOR FUTURE REFERENCE.
When using electrical appliances, basic precautions should always be followed to reduce the risk of
fire, electric shock, and injury to persons, including the following:
• To ensure correct and safe installation,
usage and functioning of the product,
always follow these instructions care-
fully and keep for future reference.
• Use only the supplied AC power adapter.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning the use of the appli-
ance by person responsible for their safety.
• Never use any optical devices such
as a lens to look directly into the light
beam. This can cause eye damage.
• Do not allow to be used as a toy.
Close attention is necessary when
used by or near children. Children
should be supervised to ensure that
they do not play with the product.
• Keep packaging materials out
of children's reach (e.g. plastic
bags...). Danger of suffocation.
• Do not operate any light with a dam-
aged cord or after malfunction occurs,
or damaged in any manner. Discard the
light, or return it to an authorized ser-
vice facility for examination or repair.
• Do not place this unit near extreme heat
sources, moisture, or corrosive substances.
• Always switch off the power prior to instal-
lation, maintenance or repair activities.
• Do not remove the power plug with wet
hands as it may cause electrical shock.
• If you notice any smoke, unusual noises
or strange smells, turn off the unit im-
mediately and remove the plug from the
wall outlet. Stop using the device and
check by authorized service personnel.
• Do not dismantle the product by your-
self, always ask professional electricians
or authorized technicians for repair.
• The external flexible cable or cord of this
luminaire cannot be replaced; if the cord is
damaged, the luminaire shall be destroyed.
• Follow local ordinances and recycling in-
structions regarding disposal or recycling
of the device and device components.
• If you have any product problems or
report an unexpected situation during
use, please contact the Customer Sup-
port at support@taotronics.com.
FOR HOUSEHOLD USE ONLY
READ AND SAVE THESE INSTRUCTIONS
Product Features
Your new TaoTronics LED Floor Lamp is perfect for lighting up your whole room:
• Convenient Remote Control & Controller
• Ultra Extended Lifespan: 50000-Hour Long Lasting LED
• Safe & Stable with a Well Weighed Base
• Easy to Assemble & Move
03 ENGLISH ENGLISH 04
Knowing Your Floor Lamp
USER GUID E
Thank you
Main Lamp
Pole Section 4
Pole Section 3
Pole Section 2
Pole Section 1
Side Lamp
Controller
Power Connector
Base
Power Adapter
User Guide
Thank You Card
Assembly
1
2
3
4
5Fully Insert
05 ENGLISH ENGLISH 06
Assembly
6
Using Your Floor Lamp
Getting Started
1Connect to power adapter.
2Plug into an appropriate electrical outlet.
1
2
07 ENGLISH ENGLISH 08
Using Your Floor Lamp
Controlling via Controller
Turn ON
• Press once.
Brightness Adjustment
• With lamp on, repeatedly short press to cycle through brightness level 1->2->3->4-> OFF.
Color Temperature Adjustment
• With lamp on, press and hold to steplessly adjust color temperature.
Main Lamp
Side Lamp
Using Your Floor Lamp
Controlling via Remote
32.8ft / 10m Remote Distance
Side Lamp Control (Same set as Main Lamp)
Main Lamp Control (ON/OFF/Brightness Adjustment)
• Turn ON: Press once.
• Turn OFF: Press and hold for 1 second.
• With lamp on, repeatedly short press to cycle through
4 brightness levels.
Turn ON/OFF
• Press once to turn on both lamps.
• Press once again to turn off.
Main Lamp Control (Color Temperature Adjustment)
• With lamp on, repeatedly short press to cycle through 4
color temperatures.
Side Lamp Control (Same set as Main Lamp)
Main Lamp Control
Side Lamp Control
09 ENGLISH ENGLISH 10
Using Your Floor Lamp
Charging Remote Control
Charging
Flashes Slowly
Battery Low ≤ 10%
Flashes Quickly
Fully Charged
Solid ON
Using Your Floor Lamp
Adjusting Lamp Head
90°
90°
90°
90°
11 ENGLISH ENGLISH 12
Model TT-DL095
Power 36W
Input DC 24V 1.5A
Color Temperature 2700K-6500K
Lumens 1400lm
CRI >80
Specifications
Cleaning and Maintenance
• Unplug the power cord from the power outlet before cleaning.
• To avoid the risk of electric shock, do not clean the base or the power cord with water and do
not immerse them.
• Wipe the lamp with a soft damp cloth.
• Clean the unit on a regular basis.
• Please store in a dry and cool place if not using for a long period of time.
Troubleshooting
The following troubleshooting guide addresses the most common problems. If problems persist,
contact the Customer Support at support@TaoTronics.com
Problem Possible Cause Solution
The stand light does not
light up
No power supply Correctly plug in the power
adapter.
The lamp is not turned on Refer to the Using Your Floor
Lamp section.
The touch control panel is
not responsive
Hands are wet Tap the panel with dry hands.
Voltage fluctuation Disconnect the power
adapter to restart the lamp.
LED failure LED component failed Please contact TaoTronics
Customer Support.
Bad smell
Power adapter failed Please contact TaoTronics
Customer Support.
Short circuit Please contact TaoTronics
Customer Support.
13 ENGLISH
Warranty
This product is covered with TaoTronics product and labor warranty for 12 months from the date of
its original purchase. If any problems occur, please contact the TaoTronics Customer Care Centre via
the contact information listed in this User Guide.
We can only provide after sales service for products that are sold by TaoTronics or TaoTronics
authorized retailers and distributors. If you have purchased your unit from a different place, please
contact your seller for return and warranty issues.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Remote control does not
respond to the lamp
Remote control is not paired
with your lamp automatically
The remote control is already
paired with your lamp
by default. If not, please
manually pair as instructed
below.
1. Press and hold both
buttons on Lamp Controller
for more than 1 second, both
lamps will flash indicating it is
under pairing mode now.
2. Press and hold the Power
button on Remote Control
until both lamps stay solid
on. Then your lamp is
successfully paired with the
remote control.
Clear Pairing History
Remote control is missing
or more than one remote
controls are connected
To disconnect the paired
remote control(s),
1. Press and hold both
buttons on Lamp Controller
for more than 1 second, both
lamps will flash.
2. To clear all pairing history,
press and hold the Main
Lamp button on Lamp
Controller for more than 3
seconds until both lamps
turn off.
3. To cancel one of the
remote controls, press and
hold the Power button on
Remote Control until both
lamps turn off.
Table of contents
Other TaoTronics Work Light manuals
