torvan ipac TorvAIR 2500 ET User manual

TorvAIR 2500/3000 115VAC ET Portable Air Filtration System Manual 2020
TorvAIR Portable
Air Filtration
System
Instruction Manual
Read and
keep this manual for
reference purposes
Models 2500 ET & 3000 ET

TorvAIR2500/3000 115VAC ET Portable Air Filtration System Manual 2020
Specifications (all models)
CLASSIFICATION
• Portable HEPA (High Eiciency Particulate Air)
100% Sealed Air Cleaning Device
• C.S.A. approved
MATERIALS: 24 gauge cold rolled steel
FINISH: Powder coated baked enamel
COLORS: Black, White
INTAKE (Upper Section)
Perforated steel enclosure surrounding a three-
stage filter assembly.
OUTFLOW (Lower Section)
Encloses motor/fan.
MOTOR/FAN
• Thermally protected Class “B” insulated motor
• Designed for continuous operation
• Run tested for 50,000 hours
• Service: 115 Volt, 60 Hz.
CONTROL: 3 Speed Electronic Control
Model 2500
DIMENSIONS: 16” W, 13.5”H
WEIGHT: 15 lbs.
AIR FLOW (C.F.M.): 50-175
POWER USAGE: 52/65 Watts @
max.
Model 3000
DIMENSIONS: 16” W 23”H
WEIGHT: 22 lbs.
AIR FLOW (C.F.M.): 50-225
POWER USAGE: 52/65 Watts @
max.
Thank you for purchasing a TorvAIR portable air filtration system. With proper care
and maintenance, your TorvAIR system will provide many years of reliable service,
improving the quality of your air.
ABOUT FILTERS AND SERVICE LIFE
The life spans of the individual filters are:
STAGE 1 PREFILTER: 3 to 6 months
STAGE 2 HEPA FILTER: 2 to 5 years
STAGE 3 V.O.C. BLANKET: 6 to 8 months
OPTIONAL V.O.C. CANISTER: 6 to 12 months
The useful service life of the filters is directly related to the volume of air passed through
the system and the amount of contaminants in the air. If your indoor air contains
abnormally high levels of airborne contaminants (such as cigarette smoke) the life of the
filters may be shortened. The HEPA filter’s particulate removal efficiency actually improves
with use as it loads up with particulates. However, as it loads up it also becomes more
difficult to move air through the system. If you notice a significant drop in air flow from the
unit, the HEPA filter should be replaced.
THREE-STAGE FILTRATION
STAGE 1: Foam Prefilter
Removes large particulates and odors. Extends the life of the HEPA
filter.
STAGE 2: HEPA Filter
99.97% eicient @ 0.3 microns. Removes dust, pollen, bacteria,
animal dander, attached viruses, cigarette smoke, radon daughters
and more.
STAGE 3: V.O.C. Blanket
Removes odors and hazardous chemicals that may o-gas from
cleaners, paints, solvents, carpets, furniture and other items
containing synthetic materials.
OPTIONAL V.O.C. Canister
For heavy-duty removal of gases and odors.

TorvAIR 2500/3000 115VAC ET Portable Air Filtration System Manual 2020
OPERATING YOUR TORVAIR HEPA AIR FILTRATION SYSTEM
OPERATION
1. Place the unit in the area where you want the cleanest air.
2. Plug the electrical cord provided into a compatible grounded outlet.
3. To operate, select the desired speed by pressing firmly on one of the buttons marked
“HIGH”, “MEDIUM” or “SILENT”. The appropriate white LED light will illuminate
and dim after 3 seconds.
4. To stop the unit operation, press firmly on the button marked “OFF”.
FILTER LIGHT INDICATORS
Your HEPA system is equipped with an electronic filter timer. This timer monitors
the life expectancy of each filter in the unit. By default, the Pre-Filter, HEPA Filter and
V.O.C. Blanket lights will turn on when the unit is powered on. After approximately 5
seconds these lights will turn off.
When a blue LED filter indicator light flashes, it is time to check and replace that filter.
-Turn the unit off and see instructions for “filter removal” to determine if filter
replacement is needed. See ‘Maintenance” on next page.
Once the filters have been checked or replaced, turn the unit back on and reset the
control panel.
-To reset, press and hold the flashing filter button until the light is constant. After
approximately 5 seconds, all of the blue LEDs will turn off.
STAGE THREE FILTER OPTION
If you have upgraded your V.O.C. Blanket to a V.O.C. Canister, you must activate the
corresponding timer.
-With the unit operating on “MEDIUM”, press and hold the V.O.C. Canister button until
the light comes on. The V.O.C. Blanket light will automatically go off. After
approximately 5 seconds, all of the blue LEDs will turn off. The control panel will now
monitor the life expectancy of the
V.O.C. Canister.
If you are switching your V.O.C. Canister to a V.O.C. Blanket, you must activate the
corresponding timer.
-With the unit operating on “MEDIUM”, press and hold the V.O.C. Blanket button until
the light comes on. The V.O.C. Canister light will automatically go off. After
approximately 5 seconds, all of the blue LEDs will turn off. The control panel will now
monitor the life expectancy of the
V.O.C. Blanket.
CAUTION
1. Make sure the cord is not in the path of people walking or where anything can be
rolled over it.
2. Do not place any objects on top of the unit or allow anyone to sit on it.
3. NEVER place any liquids or plants on the unit. Moisture could leak into the unit and
damage the filter media or electrical components.
4. The air filtration system discharges the cleaned air through the vents near the bottom
on four of the six sides. On “HIGH” the velocity of the air coming out is high to
enhance circulation throughout the area being cleaned. If the airflow is bothersome
or creates a draft, turn the unit until the air is directed toward an unoccupied area of
the room.

TorvAIR2500/3000 115VAC ET Portable Air Filtration System Manual 2020
Opening the cabinet
1. Turn the unit o and unplug it.
2. Unscrew the 5 lid screws. Once all five screws
are out, remove the
metal cover.
3. Bracing the unit so
it does not move,
turn the HEPA
cartridge counter-
clockwise and li/
pull out.
Prefilter
1. From the bottom up, pull the foam prefilter
over itself until the outside of the filter is
covered. Pull the entire foam prefilter o
of the HEPA cartridge. Discard the used
prefilter.
NOTE: The pre-fiter may contain contaminants,
remove it slowly to avoid releasing particles
back into the air.
3. Remove the plastic
shrink wrap from the new
prefilter.
4. Stretch the new filter
around the top of the
HEPA cartridge and slide
it down into place.
HEPA filter
1. With each annual filter replacement kit, a
new ‘o’ ring is provided. The old one is
removed by pinching it between two fingers
and pulling it o the collar on the blower
deck.
2. Discard old ‘o’ ring.
3. Place the new ‘o’ ring onto the collar and
slide it down to the base of the blower deck.
4. Place the new HEPA cartridge gently into
the unit.
5. When the HEPA cartridge is in place, brace
the unit, press down and gently turn it
clockwise to lock it into place. If too much
force is used, the cartridge may be diicult
to remove!
6. If replacing the HEPA filter with a new filter,
discard the old HEPA filter and use the new
filter when replacing the HEPA filter into the
unit.
Inner Carbon Filter Replacement
1. Look inside the HEPA cartridge to locate the
two ends of the inner carbon filter.
2. Pull one end of the old inner carbon filter
in and bend it into a loose roll so it can be
removed.
3. Remove the inner carbon filter from the HEPA
cartridge.
4. Remove plastic shrink wrap from the new
inner carbon filter.
5. Unroll the inner carbon filter and roll it
up in the opposite direction (this makes
the filter follow a more contoured profile
against the inner HEPA filter
surfaces and helps keep it in
place), place the rolled inner
carbon filter inside the HEPA
cartridge and gently unroll it
until the ends ‘butt’ together
and the filter is snug against
the HEPA filter.
V.O.C. Canister (OPTIONAL)
1. Remove old Carbon Filter by pulling it out
from the inside of the HEPA filter.
2. Remove the plastic shrink wrap from the
new carbon canister.
3. Place the carbon canister inside the Air
Filtration System, larger end first.
4. Slide the HEPA Filter over the V.O.C. Canister
and down into the Air Filteration System.
5. Gently, turn the HEPA Filter until it locks into
place.
Closing the cabinet
1. Position the top cover on the unit with the
centered screw hole at the rear of the unit.
2. To replace the lid screws, apply firm pressure
to the top cover to align the holes and then
insert and fasten screws.
3. Plug the unit in and turn it on.
MAINTENANCE: FILTER REPLACEMENT INSTRUCTIONS
When a red LED filter light is flashing...
HEPA Filter Replacement
As the HEPAfilter captures particulates, it will
darken over time. Replace the HEPA filter
when it darkens to example D.
A. New B. Used C. Used D. Replace

TorvAIR 2500/3000 115VAC ET Portable Air Filtration System Manual 2020
TORVAN IPAC
Questions? Comments? Email us at: [email protected]
406 Watline Avenue, Mississauga ON, L4z 1X2
TorvanIPAC is a registered trade mark of Torvan Medical Inc.
Torvan Medical Inc reserves the right to change or modify any specifications without notice.
Printed in Canada 2020..
Visit our website at: www.torvanipac.com
REPLACEMENT PARTS
Item Item Number
2500
Replacement HEPA Cartridge - 8” ET 90-A-08WG-ET
Annual Filter Kit: Standard - 8” ET 93-A-08ST00-ET
Annual Filter Kit: Plus - 8” ET 93-A-08PL02-ET
3000
Replacement HEPA Cartridge - 16” ET 90-A-16WG-ET
Annual Filter Kit: Standard - 16” ET 93-A-16ST00-ET
Annual Filter Kit: Plus - 16” ET 93-A-16PL02-ET

TorvAIR2500/3000 115VAC ET Portable Air Filtration System Manual 2020
TORVAN IPAC LIMITED WARRANTY
Torvan Medical Inc warrants TorvanIPAC HEPA Air Filtration Systems to the
original retail purchaser as follows:
The motor/fan part is warranted for five (5) years from the date of purchase under
the following conditions:
All other component parts (except filters) are warranted for one (1) year from the
date of purchase under the following conditions:
i. The TorvanIPAC HEPA Air Filtration System has failed under normal use, due
to defects in material or workmanship.
ii. The TorvanIPAC HEPA Air Filtration System has been operated according to
the manufacturers recommendations.
iii. The TorvanIPAC HEPA Air Filtration System has been operated in compliance
with the voltages specified on the product.
iv. An authorized TorvanIPAC dealer or a service provider agreed upon by both
the consumer and the manufacturer has performed an inspection.
v. There have been no attempts to modify the TorvanIPAC HEPA Air Filtration
System from its original condition.
Actions contrary to the above will void the TorvanIPAC warranty.
TorvanIPAC HEPA Air Filtration Systems that have qualified for warranty and met
all of the above conditions will, at the discretion of the manufacturer, have the
failing components repaired or replaced or, at the option of the manufacturer, be
replaced with a new system.
MAKING A WARRANTY CLAIM
The consumer may make a warranty claim by contacting TorvanIPAC.
The consumer should directly contact the Torvan Medical Inc, at 1 888 832 0355
or [email protected] to obtain a Repair or Return Authorization.
To obtain a Repair or Return Authorization, the original proof of purchase must
be presented.
RETURNING THE SYSTEM FOR WARRANTY INSPECTION AND/OR REPAIR
Prior to returning any product for warranty consideration, the consumer must
remove all filter components.
In the interest of hygiene, consumer and employee safety, TorvanIPAC will not
receive any filter media that has left the TorvanIPAC premises. Any Systems
returned for inspection with the filters included will not be received by
TorvanIPAC and will be returned to the consumer/dealer at the consumer/
dealer’s expense.
Excluding the filters, the consumer is required to return all other original system
components, including adapters if applicable. The consumer/dealer is
responsible for packaging the product appropriately to be shipped back to the
manufacturer. Torvan Medical will not be responsible for damages incurred
during return shipment due to improper packaging.
Due to issues of hygiene, consumer safety and the safety of Torvan Medical
Staff, Torvan Medical will not accept returned products on the basis of buyer’s
remorse.