Toshiba Photofact gold 43a61 User manual

SAFETY PRECASAFETY PRECA

SAFETY PRECAUTIONSUTIONS

UTIONSUTIONS

UTIONS

INDEXINDEX

INDEX

PF GOLD 15PF GOLD 15

PF GOLD 15

MODEL 43A61 (CHASSISMODEL 43A61 (CHASSIS

MODEL 43A61 (CHASSIS TT

TAA

AC0175)C0175)

C0175)C0175)

C0175)

TOSHIBOSHIB

OSHIBOSHIB

OSHIBAA

Important Parts Information ..................... 1

Miscellaneous Adjustments ...................... 1

Parts List ................................................... 6

Placement Chart ....................................... 5

Safety Precautions .................................... 1

Schematic Component Location .............. 6

Schematic Notes ....................................... 1

Schematics

Audio ................................................. 3

A/V .................................................... 4

Comb Filter ....................................... 4

Convergence ...................................... 4

Power Supply .................................... 3

System Control .................................. 3

Television .......................................... 2

VM .................................................... 1

Service Precautions .................................. 1

Test Equipment ......................................... 4

Tuner Information

H001 Main ........................................ 1

HY01 PIP .......................................... 1

For Supplier AdFor Supplier Ad

For Supplier Address,dress,

dress,dress,

dress,

See PHOSee PHO

See PHOTT

TOFOF

OFOF

OFAA

ACT AnnCT Ann

CT AnnCT Ann

CT Annual Indeual Inde

ual Indeual Inde

ual Indexx

SEPTEMBERSEPTEMBER

SEPTEMBER 2002 PG GOLD 152002 PG GOLD 15

2002 PG GOLD 152002 PG GOLD 15

2002 PG GOLD 15

TOSHIBOSHIB

OSHIBOSHIB

OSHIBAA

Model 43A61 (ChassisModel 43A61 (Chassis

Model 43A61 (Chassis TT

TAA

AC0175)C0175)

C0175)C0175)

C0175)

PF GOLD 15

Technical Service Data

PF GOLD 15

SERSER

SERVICEVICE

VICEVICE

VICE WARNINGWARNING

WARNINGWARNING

WARNING

Only qualified service technicians who are familiar with safety checks

and guidelines should perform service work. Before replacing parts,

disconnect power source to protect electrostatically sensitive parts. Do

not attempt to modify any circuit unless so recommended by the

manufacturer. When servicing the receiver, use an isolation transformer

between the line cord and power receptacle.

SERSER

SERVICINGVICING

VICINGVICING

VICING THE HIGHTHE HIGH

THE HIGHTHE HIGH

THE HIGH VV

VOLOL

OLOL

OLTT

TAA

AGE AND CRGE AND CR

GE AND CRGE AND CR

GE AND CRTT

Use EXTREME CAUTION when servicing the high voltage circuits. To

discharge static high voltage, connect a 10K ohms resistor in series with a

test lead between the receiver ground and CRT anode lead. DO NOT lift

the CRT by the neck. Always wear shatterproof goggles when handling

the CRT to protect eyes in case of implosion.

X-RAX-RA

X-RAY RADIAY RADIA

Y RADIAY RADIA

Y RADIATION AND HIGHTION AND HIGH

TION AND HIGHTION AND HIGH

TION AND HIGH VV

VOLOL

OLOL

OLTT

TAA

AGE LIMITSGE LIMITS

GE LIMITSGE LIMITS

GE LIMITS

Be aware of the instructions and procedures covering X-ray radiation. In

solid-state receivers and monitors, the CRT is the only potential source of

X-rays. Keep an accurate high voltage meter available at all times. Check

meter calibration periodically. Whenever servicing a receiver, check the

high voltage at various brightness levels to be sure it is regulating

properly. Keep high voltage at rated value, NO HIGHER. Excessive high

voltage may cause X-ray radiation or failure of associated components.

DO NOT depend on protection circuits to keep voltage at rated value.

When troubleshooting a receiver with excessive high voltage, avoid close

contact with the CRT. DO NOT operate the receiver longer than

necessary. To locate the cause of excessive high voltage, use a variable

AC transformer to regulate voltage. In present receivers, many electrical

and mechanical components have safety related characteristics which are

not detectable by visual inspection. Such components are identified by a

# on both the schematic and the parts list. For SAFETY, use only

equivalent replacement parts when replacing these components.

GENERAL GUIDELINESGENERAL GUIDELINES

GENERAL GUIDELINES

Perform a final SAFETY CHECK before returning receiver to customer.

Check repaired area for poorly soldered connections, and check entire

circuit board for solder splashes. Check board wiring for pinched wires or

wires contacting any high wattage resistors. Check that all control knobs,

shields, covers, grounds, and mounting hardware have been replaced. Be

sure to replace all insulators and restore proper lead dress.

SAFETY CHECKS — FIRE AND SHOCK HAZARDSAFETY CHECKS — FIRE AND SHOCK HAZARD

SAFETY CHECKS — FIRE AND SHOCK HAZARD

Cold LeakaCold Leaka

Cold Leakagg

ge Chece Chec

e Chece Chec

e Checks fks f

ks fks f

ks for Receiveror Receiver

or Receiveror Receiver

or Receivers with Isolated Grs with Isolated Gr

s with Isolated Grs with Isolated Gr

s with Isolated Groundound

oundound

ound

Unplug the AC cord, connect a jumper across the plug prongs, and turn

the power switch on (if applicable). Use an ohmmeter to measure the

resistance between the jumped AC plug and any exposed metal cabinet

parts such as antenna screw heads, control shafts, or handle brackets.

Exposed metal parts with a return path should measure between 1M

ohms and 5.2M ohms. Parts without a return path must measure infinity.

Hot LeakaHot Leaka

Hot Leakagg

ge Current Chece Current Chec

e Current Chece Current Chec

e Current Checkk

Plug the AC cord directly into an AC outlet. DO NOT use an isolation

transformer. Use a 1500 ohms, 10W resistor in parallel with a .15µF

capacitor to connect between any exposed metal parts on the receiver and

a good earth ground. (See figure below.) Use an AC voltmeter with at

least 5000 ohms per volt sensitivity to measure the voltage across the

resistor. Check all exposed metal parts and measure voltage at each point.

Voltage measurements should not exceed .75VAC, 500µA. Any value

exceeding this limit constitutes a potential shock hazard and must be

corrected. If the AC plug is not polarized, reverse the AC plug and repeat

exposed metal part voltage measurement at each point.

The listing of any available replacement part herein in no case constitutes a recommendation, warranty, or guarantee by

SAMS Technical Publishing as to the quality and suitability of such replacement part. The numbers of the listed parts have

been compiled from information furnished to SAMS Technical Publishing by the manufacturers of the specific type of

replacement part listed.

Reproduction or use, without express permission, of editorial or pictorial content, in any manner, is prohibited. No patent

liability is assumed with respect to the use of the information contained herein.

5436 West 78th Street

Indianapolis, IN 46268-4149

Printed in the United States of America 5 4 3 2 1

02PT01996

Paa

agg

ge 1e 1

e 1e 1

e 1 PF GOLD 15PF GOLD 15

PF GOLD 15PF GOLD 15

PF GOLD 15

• ScSc

ScSc

Schematicshematics

hematicshematics

hematics

• Component locationsComponent locations

Component locationsComponent locations

Component locations

•PP

Parar

arar

arts listts list

ts listts list

ts list

Essential coEssential co

Essential coveravera

veravera

veragg

gee

for seror ser

or seror ser

or servicing a televicing a tele

vicing a televicing a tele

vicing a television receivervision receiver

vision receivervision receiver

vision receiver......

......

...

Representative Model

UPC

HERE

Paa

agg

ge 1e 1

e 1e 1

e 1 PF GOLD 15PF GOLD 15

PF GOLD 15PF GOLD 15

PF GOLD 15

ImporImpor

Important Ptant P

tant Ptant P

tant Parar

arar

arts Infts Inf

ts Infts Inf

ts Informationormation

ormationormation

ormation

νThe parts listed here are those not usually available from a well-stocked supply cabinet or bin.

νWhere items may be replaced with equivalent parts, several alternates are shown from participating vendors.

νOn the parts lists, safety items are marked with a ##

# to remind you that only exact replacements are recommended for

these items.

νWhen ordering parts, state the model number, part number, and description.

Obtaining PObtaining P

Obtaining Parar

arar

artsts

tsts

Many of these parts are available from your local Sams authorized distributor or the manufacturer of the equipment. Call

Sams for the name of your nearest distributor:

800-428-7267

Or consult the Sams

Annual Index

for the address of the original equipment manufacturer.

Parar

arar

articipatingticipating

ticipatingticipating

ticipating VV

Vendorendor

endorendor

endorss

Information on test equipment and replacement parts is listed in these pages for the following participating vendors.

Consult the Sams

Annual Index

for their current address.

νNTE Electronics, Inc. (NTE) νSencore, Inc.

τ(1)

τ(9)

τ(7)

τ(5)

τ(3)

(2)

(4)

(6)

(8)

H001 MAINH001 MAIN

H001 MAIN TUNERTUNER

TUNERTUNER

TUNER TERMINAL GUIDETERMINAL GUIDE

TERMINAL GUIDETERMINAL GUIDE

TERMINAL GUIDE

(10)

τ(11)

(12)

τ(13)

(14)

τ(15)

(16)

τ(17)

(18)

τ(19)

(20)

τ(21)

(22)

τ(23)

(24)

τ(25)

(26)

τ(27)

H001 MAIN TUNER INFORMATION

H001 MAIN MAINH001 MAIN MAIN

H001 MAIN MAIN VV

VOLOL

OLOL

OLTT

TAA

AGE CHARGE CHAR

GE CHARGE CHAR

GE CHARTT

PinPin

Pin VHF LoVHF Lo

VHF LoVHF Lo

VHF Low Bandw Band

w Bandw Band

w Band VHF High BandVHF High Band

VHF High BandVHF High Band

VHF High Band UHF BandUHF Band

UHF BandUHF Band

UHF Band

(1) RF AGC 1.6V 1.6V 1.6V

(2) VT 1.1V 4.4V 5.4V

(3) AOS 5.0V 5.0V 5.0V

(4) SCL 4.3V 4.3V 4.3V

(5) SDA 4.3V 4.3V 4.3V

(6) NC 0V 0V 0V

(7) +5V 5.0V 5.0V 5.0V

(8) NC 0V 0V 0V

(9) BTL 33.5V 33.5V 33.5V

(10) NC 0V 0V 0V

(11) IF 0V 0V 0V

(12) IF AGC 0V 0V 0V

(13) +9V 9.0V 9.0V 9.0V

(14) NC 0V 0V 0V

(15) GND 0V 0V 0V

(16) AFT 2.6V 4.2V 1.9V

(17) AGC OUT 1.6V 1.6V 1.6V

(18) VOUT 2.3V 2.3V 2.3V

(19) NC 0V 0V 0V

(20) GND 0V 0V 0V

(21) ST 0V 0V 0V

(22) BILI/SAP 9.0V 9.0V 9.0V

(23) MODE .05V .05V .05V

(24) F MONO .13V .13V .13V

(25) MUTE 0V 0V 0V

(26) TV ROUT 4.1V 4.1V 4.1V

(27) TV LOUT 4.1V 4.1V 4.1V

NOTE: VHF Low Band voltages taken on channel 2.

VHF High Band voltages taken on channel 7.

UHF Band voltages taken on channel 14.

PF GOLD 15 PPF GOLD 15 P

PF GOLD 15 Paa

agg

ge 1e 1

e 1e 1

e 1

HY01 PIPHY01 PIP

HY01 PIP TUNERTUNER

TUNERTUNER

TUNER VV

VOLOL

OLOL

OLTT

TAA

AGE CHARGE CHAR

GE CHARGE CHAR

GE CHARTT

PinPin

Pin VHF LoVHF Lo

VHF LoVHF Lo

VHF Low Bandw Band

w Bandw Band

w Band VHF High BandVHF High Band

VHF High BandVHF High Band

VHF High Band UHF BandUHF Band

UHF BandUHF Band

UHF Band

(1) RF AGC 1.6V 1.6V 1.7V

(2) VT 1.2V 4.2V 6.0V

(3) ADRS 0V 0V 0V

(4) SCL 4.3V 4.3V 4.3V

(5) SDA 4.3V 4.3V 4.3V

(6) NC 0V 0V 0V

(7) +5V 5.0V 5.0V 5.0V

(8) NC 0V 0V 0V

(9) +32V 33.5V 33.5V 33.5V

(10) NC 0V 0V 0V

(11) IF 0V 0V 0V

(12) NC 0V 0V 0V

(13) +9V 9.0V 9.0V 9.0V

(14) AOUT 2.9V 2.9V 2.9V

(15) GND 0V 0V 0V

(16) AFT 4.8V 3.9V 3.6V

(17) RF AGC 1.6V 1.6V 1.7V

(18) V-OUT 2.4V 2.4V 2.4V

NOTE: VHF Low Band voltages taken on channel 2.

VHF High Band voltages taken on channel 7.

UHF Band voltages taken on channel 14.

τ(1)

τ(5)

τ(3)

(2)

HY01 PIPHY01 PIP

HY01 PIP TUNERTUNER

TUNERTUNER

TUNER TERMINAL GUIDETERMINAL GUIDE

TERMINAL GUIDETERMINAL GUIDE

TERMINAL GUIDE

(12)

τ(13)

(14)

τ(15)

(16)

τ(17)

(18)

τ(7)

(4)

(6)

(8)

τ(9)

τ(11)

(10)

HY01 PIP TUNER INFORMATION

PF GOLD 15 PPF GOLD 15 P

PF GOLD 15 Paa

agg

ge 1e 1

e 1e 1

e 1

TOSHIBOSHIB

OSHIBOSHIB

OSHIBA MODEL 43A61 (CHASSISA MODEL 43A61 (CHASSIS

A MODEL 43A61 (CHASSISA MODEL 43A61 (CHASSIS

A MODEL 43A61 (CHASSIS TT

TAA

AC0175)C0175)

C0175)C0175)

C0175)

MISCELLANEOUS ADJUSTMENTS

HIGHHIGH

HIGH VV

VOLOL

OLOL

OLTT

TAA

AGE CHECKGE CHECK

GE CHECKGE CHECK

GE CHECK

Tune in a picture. Set brightness, contrast, and color to MINIMUM. Turn

the set off. Remove one of the high voltage cables. Insert a High Voltage

probe tip into the vacant hole. Turn the set on, high voltage should read

31kV to 32kV. Turn the power off and insert the high voltage cable back

into the vacant hole.

ENTERINGENTERING

ENTERING THE SERTHE SER

THE SERTHE SER

THE SERVICE AND DESIGN MODESVICE AND DESIGN MODES

VICE AND DESIGN MODESVICE AND DESIGN MODES

VICE AND DESIGN MODES

To enter the service mode, press the mute button on the remote. Press the

mute button again and keep pressing while simultaneously pressing the

menu button on the receiver. The letter S will appear on the screen

indicating that the receiver is in the service mode.

When in the service mode, press the menu button on the receiver to display

the adjustment menu. To select the item to be adjusted, press the channel up

or down button. To adjust the reference value, press the volume up or down

button. To exit from the service mode or the design mode, press the power

button to turn off the receiver.

SELF DIASELF DIA

SELF DIAGNOSTIC FUNCTIONGNOSTIC FUNCTION

GNOSTIC FUNCTIONGNOSTIC FUNCTION

GNOSTIC FUNCTION

Enter the service mode. Press the 9 button on the remote to check for

proper execution of IC interfacing. The following is an explanation of what

is displayed on screen:

DisplaDispla

Displayy

yExplanationExplanation

ExplanationExplanation

Explanation

[SELF CHECK] Self diagnostic function.

No. 23000868 Part number of QA01.

POWER : 000 Operation number of protecting circuit.

000 display is normal.

BUS LINE : OK BUS line check. OK is normal.

NG indicates a short to ground of

the SCL or SDA signal or a short

between SCL and SDA.

BUS CONT : OK Bus line acknowledge check. OK is

normal. A location number is NG.

NG QA02 indicates QA02 is bad.

BLOCK : MAIN SUB Green display is normal. Cyan display is

no check. Red display is NG. UV is TV

mode, V1 is Video 1 mode, and

V2 is Video 2 mode.

SET ID : 01

EEP VER: 04

OPT1: 80

OPT2: 08

ITEM BITEM B

ITEM BUTTUTT

UTTUTT

UTTONSONS

ONSONS

ONS

The following is a list of the buttons on the remote that will go to an item

or perform a different function of the service mode:

1RCUT 5 COLC

2GCUT 6 TNTC

3BCUT 8 Toggles audio test signal on and off.

4SCNT 9 Self diagnostics

SERSER

SERVICE MODE ADJUSTMENT CHARVICE MODE ADJUSTMENT CHAR

VICE MODE ADJUSTMENT CHARVICE MODE ADJUSTMENT CHAR

VICE MODE ADJUSTMENT CHARTT

AdjustmentAdjustment

Adjustment RefRef

RefRef

Referenceerence

erenceerence

erence On SetOn Set

On SetOn Set

On Set

ItemItem

Item NameName

NameName

Name VV

Valuealue

aluealue

alue VV

Valuealue

aluealue

alue

RCUT Red Cutoff 80H 84H

GCUT Green Cutoff 80H 80H

BCUT Blue Cutoff 80H 88H

GDRV Green Drive 40H 40H

BDRV Blue Drive 40H 40H

CNTX Sub Contrast Max 7FH 7FH

BRTC Sub Brightness 80H 80H

COLC Sub Color 50H 50H

TNTC Sub Tint 44H 3AH

SCOL Sub Color 05H 08H

SCNT Sub Contrast 10H 0FH

HPOS Horizontal Position 16H 15H

VPOS Vertical Position 00H 00H

HIT Height 64H 61H

LIN Vertical Linearity 12H 13H

VSC V-S Correction 10H 10H

VPS Vertical Shift 18H 18H

VCP Vert Compensation 0AH 0AH

WID Width 28H 2CH

PARA E-W Parabola 29H 29H

CNR E-W Corner 08H 08H

TRAP Trapezium 10H 10H

HCP Horiz Compensation 00H 00H

VFC V-F Correction 00H 00H

PHUE PIP Tint 00H 00H

PCNT PIP Contrast 00H 00H

PCOL PIP Color 0FH 0FH

RGBB RGB Bright 54H 54H

PROF PIP R Offset 00H 00H

PBOF PIP B Offset 00H 00H

PGOF PIP G Offset 00H 00H

STRH Start H 67H 67H

STRP Start Ptn 88H 87H

VLD VLD 41H 42H

VCEN Vert Position 81H 8DH

OPT1 Option 1 80H 80H

OPT2 Option 2 08H 08H

TVOP TV Option 00H 00H

INITIALIZAINITIALIZA

INITIALIZATION OF QA02TION OF QA02

TION OF QA02TION OF QA02

TION OF QA02

NOTE: QA02 must be initialized after replacement.

Enter the service mode. Press and hold the recall button on the remote

while simultaneously pressing the channel up button on the receiver. The

initialization of QA02 is complete. Program channels into memory.

SUB COLOR (COLC) & SUBSUB COLOR (COLC) & SUB

SUB COLOR (COLC) & SUB TINT (TNTC)TINT (TNTC)

TINT (TNTC)TINT (TNTC)

TINT (TNTC)

Tune in a color bar pattern. Set contrast to maximum and brightness to

midrange. Connect an oscilloscope to the red cathode. Enter the service

mode. Select item COLC and adjust reference value to obtain 150Vp-p.

Tune in an active channel. Select item TNTC and adjust reference value for

proper flesh tones.

SUB BRIGHTNESS (BRSUB BRIGHTNESS (BR

SUB BRIGHTNESS (BRTC)TC)

TC)TC)

TC)

Tune in a picture. Set contrast to MINIMUM. Enter the service mode.

Select item BRTC, adjust reference value until vertical retrace line just

disappears. Adjust contrast for normal picture. Perform Height (HIT)

adjustment.

HORIZONTHORIZONT

HORIZONTAL POSITION (HPOS) &AL POSITION (HPOS) &

AL POSITION (HPOS) &AL POSITION (HPOS) &

AL POSITION (HPOS) & VERVER

VERVER

VERTICAL POSITIONTICAL POSITION

TICAL POSITIONTICAL POSITION

TICAL POSITION

(VPOS)(VPOS)

(VPOS)

Enter the service mode. Press the TV/video button on remote until a

crossbar pattern is displayed. Select item HPOS or VPOS and adjust

reference value for the horizontal and vertical position alternately until the

pattern is centered on the screen. Check the position of the picture with off-

air signal.

HEIGHT (HIT)HEIGHT (HIT)

HEIGHT (HIT)

Enter the service mode. Press the TV/video button on remote until a

crosshatch pattern is displayed. Select item HIT and adjust reference value

for slight underscan. Advance the data value by 8 steps and check the

vertical position of the picture.

WIDTH (WID)WIDTH (WID)

WIDTH (WID)

Enter the service mode. Press the TV/video button on remote until a

crosshatch pattern is displayed. Select item WID, adjust reference value for

slight underscan. Advance the reference value by 7 steps. Check for proper

horizontal position of the picture.

E-W PE-W P

E-W PARABOLA (DPC)ARABOLA (DPC)

ARABOLA (DPC)ARABOLA (DPC)

ARABOLA (DPC)

Enter the service mode. Press the TV/video button on remote until a

crosshatch pattern is displayed. Select item DPC, adjust reference value for

straight vertical lines on both sides of the pattern.

WHITE BWHITE B

WHITE BALANCE (RCUTALANCE (RCUT

ALANCE (RCUTALANCE (RCUT

ALANCE (RCUT,,

,GCUTGCUT

GCUTGCUT

GCUT,,

,BCUTBCUT

BCUTBCUT

BCUT,,

,GDRGDR

GDRGDR

GDRVV

V,,

,BDRBDR

BDRBDR

BDRV)V)

V)V)

Turn receiver on. Allow a 10 to 30 minute warm up time. Adjust contrast to

center and brightness to maximum. Enter the service mode. Press the TV/

video button on remote until the white screen pattern is displayed. Select

items RCUT, GCUT, BCUT, GDRV, and BDRV and set the reference value

for each to 40H. Press the video button on the remote to obtain a single

horizontal line. Advance the screen control until a faint line of one

predominant color appears on the screen. Adjust the other two cutoff items

to obtain a dim white line. Press the video button on the remote to get full

deflection. Select items GDRV and BDRV and adjust reference value of

each for the best black and white picture on screen.

CONVERGENCE ADJUSTMENTCONVERGENCE ADJUSTMENT

CONVERGENCE ADJUSTMENT

Select the Adjustment mode RCUT, GCUT, or BCUT of the service mode.

Adjust convergence from center to circumference in order. Press “7” button

to display the built-in crosshatch pattern, it includes the three colors (R, G,

B). The cursor should be blinking in Red, this means that the Red conver-

gence around the cursor can be done. Press “3” button to select the Green

color to be adjusted. Press “2” up, “8” down, “4” left, “6” right to move

the cursor to other point to be adjusted. Press “5” button to stop the cursor

from blinking, or to start the cursor blinking again. If necessary a specified

color line can be erased from the screen, press “100” button to erase Red

line. Press “0” button to erase Green line. Press “ENT” or “RTN” button to

erase Blue line. Repeat these steps to adjust the Red and Blue colors.

Converge the selected color into the Green line. Press “7” button to save the

adjustment changes. Press “7” button again to return to normal picture.

SERVICE PRECAUTIONS

Do not use a magnetized screw driver for screws of Deflection Yoke and

Velocity Modulation Coil, to avoid magnetization of electron gun.

Magnetization of electron gun will degrade basic function, and result in

unbalance of right and left shift of user static convergence, and result in no

variable quantity.

When replacing a CRT:

DO NOT LOOSEN OR ADJUST ANY OF THE HEX HEAD SCREWS.

These screws are for sealing of CRT coolant fluid, loosening any of

these screws will cause fluid leakage.

When replacing the anode cap assembly, or the anode lead assembly

remove the anode lead holder from old assembly and attach it to the new

anode lead, and make sure the point of the anode lead would be straight

coming out of the lead holder.

Paa

agg

ge 2e 2

e 2e 2

e 2 PF GOLD 15PF GOLD 15

PF GOLD 15PF GOLD 15

PF GOLD 15

PF GOLD 15 PPF GOLD 15 P

PF GOLD 15 Paa

agg

ge 2e 2

e 2e 2

e 2

Paa

agg

ge 2e 2

e 2e 2

e 2 PF GOLD 15PF GOLD 15

PF GOLD 15PF GOLD 15

PF GOLD 15

PF GOLD 15 PPF GOLD 15 P

PF GOLD 15 Paa

agg

ge 2e 2

e 2e 2

e 2

TOSHIBOSHIB

OSHIBOSHIB

OSHIBA MODEL 43A61 (CHASSISA MODEL 43A61 (CHASSIS

A MODEL 43A61 (CHASSISA MODEL 43A61 (CHASSIS

A MODEL 43A61 (CHASSIS TT

TAA

AC0175)C0175)

C0175)C0175)

C0175)

Paa

agg

ge 3 PF GOLD 15e 3 PF GOLD 15

e 3 PF GOLD 15e 3 PF GOLD 15

e 3 PF GOLD 15

PF GOLD 15 PPF GOLD 15 P

PF GOLD 15 Paa

agg

ge 3e 3

e 3e 3

e 3

PF GOLD 15 PPF GOLD 15 P

PF GOLD 15 Paa

agg

ge 3e 3

e 3e 3

e 3

Paa

agg

ge 3e 3

e 3e 3

e 3 PF GOLD 15PF GOLD 15

PF GOLD 15PF GOLD 15

PF GOLD 15

PF GOLD 15 PPF GOLD 15 P

PF GOLD 15 Paa

agg

ge 3e 3

e 3e 3

e 3

TOSHIBOSHIB

OSHIBOSHIB

OSHIBA MODEL 43A61 (CHASSISA MODEL 43A61 (CHASSIS

A MODEL 43A61 (CHASSISA MODEL 43A61 (CHASSIS

A MODEL 43A61 (CHASSIS TT

TAA

AC0175)C0175)

C0175)C0175)

C0175)

Paa

agg

ge 4 PF GOLD 15e 4 PF GOLD 15

e 4 PF GOLD 15e 4 PF GOLD 15

e 4 PF GOLD 15

PF GOLD 15 PPF GOLD 15 P

PF GOLD 15 Paa

agg

ge 4e 4

e 4e 4

e 4

Paa

agg

ge 4e 4

e 4e 4

e 4 PF GOLD 15PF GOLD 15

PF GOLD 15PF GOLD 15

PF GOLD 15

PF GOLD 15 PPF GOLD 15 P

PF GOLD 15 Paa

agg

ge 4e 4

e 4e 4

e 4

TOSHIBOSHIB

OSHIBOSHIB

OSHIBA MODEL 43A61 (CHASSISA MODEL 43A61 (CHASSIS

A MODEL 43A61 (CHASSISA MODEL 43A61 (CHASSIS

A MODEL 43A61 (CHASSIS TT

TAA

AC0175)C0175)

C0175)C0175)

C0175)

TEST EQTEST EQ

TEST EQUIPMENTUIPMENT

UIPMENTUIPMENT

UIPMENT

Test equipment listed by participating manufacturer illustrates typical or

equivalent equipment used by Sams engineers to obtain measurements.

This equipment is compatible with most types used by field service

technicians.

EquipmentEquipment

Equipment Sencore No.Sencore No.

Sencore No.Sencore No.

Sencore No.

Oscilloscope SC3100

Generators

RGB CM2125

Multiburst Signal VG91

Color Bar VG91

TV Stereo VG91

Digital VOM SC3100

Frequency Meter SC3100

Hi-Voltage Probe HP200

Accessory Probes TP212

Isolation Transformer PR570

Capacitance Analyzer LC102

CRT Analyzer CR7000

AC Leakage Tester PR570

Inductance Analyzer LC102

Flyback Yoke Tester TVA92

Field Strength Meter SL753

Transistor Tester TF46

Horizontal Analyzer HA-2500

Video Analyzer VG91, TVA92

Paa

agg

ge 5e 5

e 5e 5

e 5 PF GOLD 15PF GOLD 15

PF GOLD 15PF GOLD 15

PF GOLD 15

PF GOLD 15 PPF GOLD 15 P

PF GOLD 15 Paa

agg

ge 5e 5

e 5e 5

e 5

PF GOLD 15 PPF GOLD 15 P

PF GOLD 15 Paa

agg

ge 5e 5

e 5e 5

e 5

Paa

agg

ge 5e 5

e 5e 5

e 5 PF GOLD 15PF GOLD 15

PF GOLD 15PF GOLD 15

PF GOLD 15

PF GOLD 15 PPF GOLD 15 P

PF GOLD 15 Paa

agg

ge 5e 5

e 5e 5

e 5

TOSHIBOSHIB

OSHIBOSHIB

OSHIBA MODEL 43A61 (CHASSISA MODEL 43A61 (CHASSIS

A MODEL 43A61 (CHASSISA MODEL 43A61 (CHASSIS

A MODEL 43A61 (CHASSIS TT

TAA

AC0175)C0175)

C0175)C0175)

C0175)

Other manuals for Photofact Gold 43A61

Table of contents

Other Toshiba Air Conditioner manuals

Toshiba

Toshiba RAS-B10N3KVP Series User manual

Toshiba

Toshiba RAC-PT1411HWRU User manual

Toshiba

Toshiba RAS-05BKVG-E User manual

Toshiba

Toshiba TCB-SIR41U-E User manual

Toshiba

Toshiba RAV-RM401MUT-E User manual

Toshiba

Toshiba BMS-IFMB0TLR-E User manual

Toshiba

Toshiba RAV-133TU-PE User manual

Toshiba

Toshiba Carrier TCB-IFDMR01UP-UL User manual

Toshiba

Toshiba RAV-GM802ATW-E User manual

Toshiba

Toshiba MMU-UP0071MH-UL User manual

Toshiba

Toshiba RAV-GP561ATP-E User manual

Toshiba

Toshiba RAS-18J2KVG-TR User manual

Toshiba

Toshiba RAS-16BAVG-E User manual

Toshiba

Toshiba RAV-SM560KRT-E User manual

Toshiba

Toshiba MMU-AP0091H Guide

Toshiba

Toshiba MMY-MAP1006FT8(J)P-E User manual

Toshiba

Toshiba RAS-25S4KVDG-ND User manual

Toshiba

Toshiba RAS-24NKHD-E4 User manual

Toshiba

Toshiba RAV-GM561DTP-A User manual

Toshiba

Toshiba RAV-GM301ATP-NZ User manual

Toshiba

Toshiba RAS-24N3K-M User manual

Toshiba

Toshiba RAV-GV1601ATP-TR User manual

Toshiba

Toshiba MMC-UP0151HP-E User manual

Toshiba

Toshiba RBC-AXU31UM-E User manual

Popular Air Conditioner manuals by other brands

Lloyd

Lloyd LS18HC user manual

American Standard

American Standard 4A6V8024A1000B Service facts

LG I27TTC owner's manual

Friedrich

Friedrich WallMaster WS10 Installation and operation manual

Honeywell

Honeywell CL30XC owner's manual

Whynter

Whynter ARC-12SDH instruction manual

AirStage

AirStage ASUA7RLAV installation manual

Airxcel

Airxcel Marvair ComPac II AVHDA90 Installation & operation manual

Eberg

Eberg QUBO Q40HD instruction manual

Hitachi

Hitachi RAK-18PSPA installation manual

Arbonia

Arbonia SABIANA OCEAN Series Installation and maintenance manual

Samsung

Samsung AW05F05EA Owner's instructions

Airwell

Airwell AWSI-HDD018-H11 Service manual

Technibel

Technibel KPAFP165R5IA Series installation manual

Samsung

Samsung SH18BW6 Series user manual

INVENTOR

INVENTOR OMI-09 owner's manual

Haier

Haier HSU-18LEK03/R2 Service manual

LG LS243HLV3 Engineering manual

Toshiba Photofact Gold 43A61 User manual

Popular Air Conditioner manuals by other brands