Toshiba SD-K780KU User manual

SD-K780KU
Owner’s Record
The model number and serial number are on the back
of your DVD Player. Record these numbers in the spaces
belowRefer to these numbers whenever you
communicate with your Toshiba dealer about this DVD
Player.
Model number:
Serial number:

1
English
Introduction
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE.
DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND.
CAUTION:
PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS OWNER'S
MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
CAUTION:
USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
FCC NOTICE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rule.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modications made to this equipment, not expressly approved by Toshiba, or parties
authorized by Toshiba, could void the user' s authority to operate the equipment.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
 ampliers)thatproduceheat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third
CAUTION: VISIBLE LASER RADIATION WHEN
OPEN. DO NOT STARE INTO BEAM.
 Thelightningashwitharrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated 'dangerous voltage'within
the product' s enclosure that may be of
sufcientmagnitudetoconstituteariskof
electric shock to persons.
The exclamation point within an equila-
teral triangle is intended to alert the user
to the presence of important operating
andmaintenance(servicing)instructions
in the literature accompanying the
appliance.
The symbol for CLASS II (Double
 Insulation)
SAFETY PRECAUTIONS
IMPORTANT SAFETY INSTRUCTIONS

2
English
Introduction
prongareprovidedforyoursafety.Iftheprovidedplugdoesnottintoyouroutlet,consultanelectricianfor
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Onlyuseattachments/accessoriesspeciedbythemanufacturer.
12. Useonlywiththecart,stand,tripod,bracket,ortablespeciedbythemanufacturer,orsoldwith
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Referallservicingtoqualiedservicepersonnel.Servicingisrequiredwhentheapparatushasbeendamagedin
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Additional Safety Instructions
15. Donotoverloadwalloutlets;extensioncords,orintegralconveniencereceptaclesasthiscanresultinariskofre
or electric shock.
16. Apparatusshallnotbeexposedtodrippingorsplashingandnoobjectslledwithliquids,suchasvases,shallbe
placed on the apparatus.
17. Keepyourngerswellclearofthedisctrayasitisclosing.Neglectingtodosomaycauseseriouspersonalinjury.
18. Do not place a heavy object on or step on the apparatus. The object may fall, causing serious personal injury and
serious damage to the apparatus.
19. Do not use a cracked , deformed, or repaired disc. These discs are easily broken and may cause serious personal
injury and apparatus malfunction.
20. If the apparatus should smoke or smell,immediately disconnect the power cord from the wall outlet. Wait until the
smokeorsmellstops,thenaskyourdealerforacheckandrepair.Neglectingtodosomaycausere.
21. While it is thundering, do not touch the connecting cables or the apparatus.
22. Warning:Topreventthespreadofre,keepcandlesorotheropenamesawayfromthisproductatalltimes.
CAUTION:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference
Should the unit require maintenance, contact an authorized service location.
 Useofcontrolsoradjustmentsorperformanceofproceduresotherthanthosespeciedhereinmayresultin
hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible and invisible laser radiation when open and interlocks defeated.
DO NOT STARE INTO BEAM.
Location of the required label:
CERTIFICATION:This product complies
with FDA Rule 21 CFR Subchapter J in
effect at date of manufacture.
CAUTION:Theseservicinginstructionsareforusebyqualiedservicepersonnelonly.Toreducetheriskof
electric shock do not perform any servicing other than that contained in the operating instructions unless you are
qualiedtodoso.
Be aware that this equipment is still powered when in standby mode. To disconnect this equipment completely from the
mains power, pull out the power plug from the wall outlet.
Environmental Information
All unnecessary packaging has been omitted. The packaging has been made easy to separate into three materials;
cardboard(box),polystyrenefoam(buffer)andpolyethylene(bags,protectivefoamsheet).
Your DVD player consists of materials which can be recycled and reused if disassembled by a specialised company.
Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old
equipment.
LASER
Type Semiconductor laser
  InGaAIP(DVD)
  AIGaAs(CD)
Wavelength658nm(DVD)
  790nm(CD)
OutputPower10.0mW(DVD)
  7.0mW(VCD/CD)
Beam divergence 60 degrees

3
English
CAUTION!
Do not use solvents such as benzene, thinner,
commercially available cleaners, or anti-static sprays
intended for analog discs. Since the optical unit
 (laser)oftheDVDsystemoperatesatahigher
power than regular DVD or CD players, cleaning
CDs intended for DVD or CD players may damage
theopticalunit(laser).Therefore,refrainfromusing
a cleaning CD.
Moisture Condensation
Moisture condensation damages the DVD player.
Please read the following carefully. Moisture
condensation occurs, for example, when you pour a
cold drink into a glass on a warm day. Drops of water
form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts
of the DVD player.
If you use the DVD player in such a situation, it may
damage discs and internal parts. Remove the disc,
connect the power cord of the DVD player to the wall
outlet, turn on the DVD player, and leave it for two or
three hours. After two or three hours, the DVD player
will have warmed up and evaporated any moisture.
Keep the DVD player connected to the wall outlet
and moisture
condensation will seldom occur.
Region Codes
This DVD player is designed to support the Region
Management System. Check the regional code
number on the disc package. If the number does
not match the player's region number (see table on
page4),theplayermaybeunabletoplaybackthe
disc.
Tips:
-It may not be possible to play CD-R/RW , DVD+R/
RW , or DVD+R DL in all cases due to the type of
disc or condition of the recording.
-If you are having trouble playing a certain disc,
remove the disc and try a different one. Improperly
formatted disc will not play on this DVD Player.
WARNING:
RISK OF ELECTRIC SHOCK!
Never attempt to service this product yourself.
Opening and removing the covers may expose you
to dangerous voltage or other hazards. Failure to
follow this WARNING may result in death or serious
injury.Referallservicingnotspeciedinthismanual
to a Toshiba Authorized Service Center.
Setup
Finding a suitable location
 -Placethesetonaat,hardandstablesurface.
-Do not place the set on a carpet.
-Do not position the set on top of other equipment
 thatmightheatitup(e.g.,receiveroramplier).
-Do not put anything under the set
 (e.g.CDs,magazines).
-Install this unit near the AC outlet and where the
AC power plug can be reached easily.
Space for ventilation
-Place the apparatus in a location with adequate
ventilation to prevent internal heat build up. Allow at
least 10 cm (4.0'')clearancefromtherearandthe
top of the set and 5 cm (2.0'')fromtheleftandright
to prevent overheating.
10cm (4.0") 10cm (4.0")
5cm (2.0")
5cm (2.0")
Avoid high temperatures, moisture, water and
dust
-Apparatus shall not be exposed to dripping or
splashing.
-Do not place any sources of danger on the
 apparatus(e.g.,liquidlledobjects,lightedcandles).
Cleaning discs
Some problems occur because the disc inside the
system is dirty (frozen picture, sound disruptions,
picturedistortions).Toavoidtheseproblems,discs
should be cleaned on a regular basis.
 Tocleanadisc,useamicrobrecleaningcloth
and wipe the disc from the center to the edge in a
straight line. Do not touch the playback side of the
disc.
Introduction

4
English
Introduction
ALL 4
Region
U.S.A. and
Canada regions
U.K.,
Europe regions and
Asia Paci c,
Taiwan, Korea
Australia,
New Zealand,
Latin America
Russia and
India regions
China, Calcos Islands,
Walls and Futuna
Islands
ALL
ALL
5
6
Discs that can
be played
ALL 1
ALL
ALL
2
3
Japan
Helpful hint: Before making or changing any connections, make sure that all the devices are
disconnected from the power outlet.
This product incorporates copyright protection tech-
nology that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.
Notes on copyright
The unauthorized recording, use, distribution, or revision
of television programs, videotapes, DVDs and other
materials, is prohibited under the Copyright Laws of the
United States and other countries, and may subject you
to civil and/or criminal liability.

5
English
Introduction
Introduction
SAFETY PRECAUTIONS 1
IMPORTANT SAFETY INSTRUCTIONS 1-2
Setup 3
Cleaning discs 3
Moisture Condensation 3
Region Codes 3-4
Table of Contents 5
Connections
Connecting to television 6-7
Connecting to a Stereo System 7
Connecting to a Digital AV Receiver 8
Connecting the power cord 8
Product Overview
Front and Rear panels 9
Remote Control 10
Getting Started
Inserting Batteries 11
Finding your viewing channel 11
Setting up Progressive Scan feature 11-12
Setting the language 12
.Playback from Disc
Playable discs 12-13
Playback Feature
Starting disc playback 13
Basic playback control 13-14
Operationsforvideoplayback(DVD/VCD/SVCD)     14
Selecting various repeat functions 14-15
Viewing the disc playback Information 15
Special DVD Features 15
Special VCD and SVCD Features 15
Playing MP3/JPEG/Kodak picture CD 16-17
DVD menu Options
Using the Language setup menu 17
Using the Video setup menu 17-18
Using the Audio setup menu 18-19
Using the Rating setup menu 19-20
UsingtheMisc(Miscellaneous)setupmenu     20
Tray Lock 20
Others
Specications       21
Troubleshooting 22-23
Glossary 24
Limited United States Warranty 25
Canadian Warranty Information 26-27
Table of Contents

6
English
Connecting to television
IMPORTANT!
– You only need to make one video connection
from the following options, depending on the
capabilities of your television.
– Connect the DVD player directly to the
television.
Using Composite Video Jack(CVBS)
A Usethecompositevideocable(yellow)toconnect
the DVD player'sVIDEO(CVBS)jacktothevideo
input jack(or the labeled as A/V in,Video In or
 Composite)ontheTV(cablesupplied).
To hear the sound of this DVD player through your
TV,usetheaudiocables(white/red)toconnect
 AUDIOOUT(L/R)jacksoftheDVDplayerto
corresponding AUDIO IN jacks on the TV(cable
 supplied).
Using Component Video Jacks(Y, PB, PR)
IMPORTANT!
-The progressive scan video quality is only
possible when using Y, PB, PRand a progressive
scan TV is required.
A Usethecomponentvideocables(red/blue/green)to
connect the DVD player's Y, PB, PRjacks to the
corresponding Component video input jacks (or
labeled as Y, Pb, Pr)ontheTV(cablenotsupplied).
B Usetheaudiocables(white/red)toconnectAUDIO
OUT(L/R)jacksoftheDVDplayertothe
corresponding AUDIO IN jacks on the TV.
CProceed to page 11 for detailed Progressive Scan set
up.
Using a RF modulator
IMPORTANT!
-If your TV only has a single Antenna In jack (or
labeled as 75 ohm or RF In), you will need an RF
modulator in order to view the DVD playback on
the TV.
A Usethecompositevideocable(yellow)toconnect
the DVD player'sVIDEO(CVBS)jacktothevideo
inputjackontheRFmodulator(cablesupplied).
To hear the sound of this DVD player through your
TV,usetheaudiocables(white/red)toconnect
 AUDIOOUT(L/R)jacksoftheDVDplayertothe
corresponding AUDIO IN jacks on the RF modulator
(cablesupplied).
B UsetheRFcoaxialcable(notsupplied)toconnect
ANTENNA OUT or TO TV jack on the RF modulator
to the ANTENNA IN jack on the television.
CConnect the Antenna or Cable TV service signal to
the ANTENNA IN or RF IN jack on the RF modulator.
(It may have been connected to your TV previously.
DisconnectitfromtheTV.)
Connections
Helpful hint: Before making or changing any connections, make sure that all the devices are
disconnected from the power outlet.

7
English
Connections
Helpful hint: Before making or changing any connections, make sure that all the devices are
disconnected from the power outlet.
Using S -VIDEO Jack
AUse the S - Video cable to connect the DVD player's
S-VIDEO jack to the S-VIDEO jack on the TV(cable
notsupplied).
BTo hear the sound of this DVD Player through your
TV,usetheaudiocables(white/red)toconnect
AUDIOOUT(L/R)jacksoftheDVDplayertothe
corresponding AUDIO IN jacks on the TV.
CSet Video Out to S-VIDEO to enable output of
S-Video signal (see page 18{VideoOut}).
Tip:
-Using S-Video and Component Video jacks in
combination is not recommended when you connect
to television.
(1)Connect the Audio out (L/R) cables .
(2)Press “SETUP” button on the remote control .
(3)Select "Video Out" in “Video”.
(4)Select "S-VIDEO".
(5)Connect a S-Video cable.
Connecting to a Stereo System
MAINS
MAINS
Stereo system has Dolby Pro Logic or Right/Left
Audio In Jacks
ASelect one of the video connections (CVBS VIDEO
IN,S-VIDEOINorCOMPONENTVIDEOIN)
depending on the options available on your TV.
B Usetheaudiocables(white/red)toconnectAUDIO
OUT(L/R)jacksoftheDVDPlayertothe
corresponding AUDIO IN jacks on the stereo system .

8
English
Connections
Helpful hint: Before making or changing any connections, make sure that all the devices are
disconnected from the power outlet.
Connecting to a Digital AV Receiver
Receiver has a PCM, Dolby Digital or MPEG
decoder
ASelect one of the video connections (CVBS VIDEO
IN,S-VIDEOINorCOMPONENTVIDEOIN)
depending on the options available on your TV.
BConnect the COAXIAL jack of the DVD player to the
corresponding Digital Audio In jack on your Receiver
(cablenotsupplied).
CSet the DVD Player' s Digital Output to PCM-Only or
ALL depending on the capabilities of your Receiver
(seepage19{DigitalOutput}).
Tip:
-If the audio format of the Digital Output does not
match the capabilities of your receiver, the receiver
will produce a strong, distorted sound or no sound at
all.
Connecting the power cord
MAINS
After everything is connected properly, plug in the AC
power cord to the power outlet.
Never make or change any connections with the
power switched on.
“----” will appear on the display window when you
press the ON/STANDBY button with no disc loaded.

9
English
Disc tray
- Place a disc here
Display
- Shows information about the current status of the
DVD Player
IR Sensor
- Points the remote control towards this sensor
MAINS ~
- Connects to a standard AC outlet
AUDIO OUT (Left/Right)
-ConnectstoAudioinputofaTV,anamplier,
receiver or stereo system
COAXIAL(Digital audio out)
- Connects to coaxial Audio input of a digital audio
equipment
DVD display
The indicators vary depending on the kinds of disc
you play.
Multifunctional indicator (indicates
operating status or messages, etc.)
Chapter/Track
number indicator
Product Overview
Front and Rear panels
I/2ON/STANDBY
-Turns the player on or switches it to
standby mode
B/X PLAY/ PAUSE
-Starts or pauses playback
STOP
- Stops playback
çOPEN/CLOSE
- Opens or closes the disc tray
S-VIDEO
- Connects to S-Video input of a TV
Y, PB, PRComponent Video Out
- Connects to Y, PB, PRinput of a TV
VIDEO Out (CVBS)
- Connects to CVBS Video input of a TV
No disc Bad disc
OPEN LOAD/CLOSE
DVD video disc VIDEO CD Audio CD
•During playback: •During playback: •During playback:
Example Example Example
Some discs may only
display chapter
numbers.
Some discs may only
display track
numbers.
Some discs may only
display track
numbers.

10
English
Product Overview
Remote Control
[ 15 ]DISPLAY
-Displays information on
TV screen during playback
[ 13 ]OPEN/CLOSE
-Open/close the disc tray
[ 13, 15, 19 ]Number Buttons
-Selects numbered items in a menu
-Press to enter track/chapter/title
numbers or password directly
[ 13 ]+10 button
-Press to enter number greater than 9
-Press +10 button repeatedly to select
10,20,30...etc
[ 14, 15 ]MENU
-Enters or exits the disc menu
-Switches on or off the Playback
Control(PBC)mode(forVCD2.0/
SVCDonly)
[ 12 ]OK
-Acknowledge menu selection
[ 15 ]RETURN
-To go back to previous menu
[ 15 ]TITLE
-Show title menu
[ 14, 16 ]F.R & F.F
-Do a forward/reverse search
[ 13, 15, 16 ]PREV & NEXT
-Skip to previous / next chapter /track
[ 14 ]REPEAT
-Selects various repeat mode
[ 15 ]A-B
-Repeats playback from point A to B on
a disc
[ 14 ]SLOW
-Do a slow forward
[ 14 ]CLEAR
-Delete the mistyped entries or cancel
some functions
REMOTE SIGNAL EMITTER
[ 11 ]
-Point remote control to the sensor on
the front panel
2ON / STANDBY[ 8, 11, 13 ]
-To switch the DVD player to ON or
standby mode
T - SEARCH[ 15 ]
-Start playback from a designated
point
SETUP[ 11, 17 ]
-Enters or exits the system setup
menu
[ 14, 16, 17 ]
-Cursor buttons for moving to the left
/ right / up / down
-To rotate the JPEG picture during
playback
STEP
-Play video frame by frame
PLAY/PAUSE [ 13, 14 ]
-Starts or pauses playback
STOP [ 13 ]
-Stops play
SUBTITLE[ 15 ]
-To access subtitle language
ANGLE[ 15 ]
-Switch the camera angle during
playback
AUDIO[ 15 ]
-Selectsanaudiosetting(DVD)oran
audiochannel(VCD)
ZOOM[ 14, 16 ]
-Enlarge a picture on the TV
RANDOM [ 16 ]
-Toggles between Normal and
Random playback
PROG[ 14 ]
-To program playback or cancel the
program playback
See the page in [ ] for details.

11
English
Inserting Batteries
AOpen the battery compartment.
BInsert two batteries type R03 or AAA, following the
indications(+/-)insidethecompartment.
CClose the cover.
CAUTION:
Neverthrowbatteriesintoare.
Note:
- Be sure to use AAA size batteries.
- Dispose of batteries in a designated disposal area.
- Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in
accordance with applicable laws and regulations.
- If the remote control does not operate correctly, or if
the operating range becomes reduced, replace batteries
with new ones.
- When necessary to replace batteries in the remote
control, always replace both batteries with new ones.
Never mix battery types or use new and used batteries
in combination.
- Always remove batteries from remote control if they
are dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid
from leaking into the battery compartment.
Using the Remote Control to Operate
the System
OPEN/CLOSE DISPLAY
1 2 3
6
5
4
7 8 9
+10 0
T-SEARCH
SETUP
MENU
RETURN TITLE
OK
F.R F.F PREV NEXT
STEP STOP
PLAY/PAUSE
REPEAT A-B
SUBTITLE ANGLE AUDIO ZOOM
SLOW
PROGRANDOM
S E -R 0 2 6 8
ON/STANDBY
CLEAR
30 30
Within about 6m (19 feet)
AAim the Remote Control directly at the remote sensor
(IR)onthefrontpanel.
BDo not put any objects between the Remote Control
and DVD Player while operating the DVD Player.
Finding your viewing channel
APress I/2ON/STANDBY on the DVD player to turn it
on.
BTurn on the TV and set it to the correct video-in
channel. You should see the blue DVD background
screen.
Usually these channels are between the lowest
and highest channels and may be called FRONT,
A/V IN or VIDEO. See your TV' s manual for more
details.
Or, you may go to channel 1 on your TV, then
press the Channel down button repeatedly until you
see the Video In channel.
Or, the TV remote control may have a button that
chooses different video modes.
Or, set the TV to channel 3 or 4 if you are using an
RF modulator.
CIf you are using external equipment, (such as
audiosystemorreceiver),turnitonandselectthe
appropriate input source for the DVD player output.
Refer to the equipment user’s manual for detail.
Setting up Progressive Scan feature
(For Progressive Scan TV only)
The progressive scan display twice the number
of frames per seconds than interlaced scanning
(ordinarynormalTVsystem).Withnearlydouble
the number of lines, progressive scan offers higher
picture resolution and quality.
Before you start...
-Ensure that you have connected this DVD player
to a progressive scan TV using the Y, PB, PR
connection(seepage6).
-Ensure that you have completed the basic
installation and set up.
ATurn on your TV and select the video input
connected to the DVD player (refer to your TV user
manual).
BPress 2ON/STANDBY on the remote control to turn
on the DVD player.
The blue DVD background screen will appear on
the TV.
CPress SETUP.
DPress /to select { Video }, then press .
Aspect Ratio :
View Mode :
4:3
Auto Fit
Aspect Ratio
View Mode
4:3
Auto Fit
Language
Video
Audio
Misc
Rating
P-Scan
Video Out S - VIDEO
Smart Picture Component
EPress /to select { Video Out }, then press .
FSelect { P- Scan},thenpressOKtoconrm.
The menu will appear on the TV.
Activating Progressive Scan 1. Ensure
your TV supports Progressive Mode
2. If there is a distorted picture on the
TV, wait 15 seconds for automatic
recover
NoYes
Video Out
Getting Started
Helpful hint: Press to go back to previous menu item.
Press SETUP to exit the menu item.

12
English
GPress to highlight { Yes}andpressOKtoconrm.
 ThereconrmationmenuwillappearontheTV.
Confirm again to use new setting
14
NoYes
Video Out
HPress to highlight { Yes}andpressOKtoconrm.
The setup is now completed and you can start
enjoying the high quality picture.
To deactivate Progressive Scan
manually:
AWait for 15 seconds for the auto recovery.
OR
APress OPEN/CLOSE çon the DVD player to open
the disc tray.
BPress number button ' 1 'on the remote control for a
few seconds.
The DVD background screen appears.
Tip:
-There are some progressive scan TVs and High-
Denition TVs that are not fully compatible with this
unit, resulting in the unnatural picture when playing
back a DVD VIDEO disc in the progressive scan
mode. In such a case, turn off the progressive scan
feature on both the DVD player and your TV.
Setting the language
 ChooseyourdesiredOn-ScreenDisplay(OSD)language
including English, French and Spanish.
On-Screen Display (OSD) Language
The On-screen language for the system setup menu
will remain as you set it, regardless of various disc
languages.
Audio : English
DVD Menu :English
OSD language English
Subtitle French
Spanish
Language
Video
Audio
Misc
Rating
APress SETUP.
BPress /to select { Language }
CPress to highlight { OSD language }, then press
.
DPress /to select a language and press OK.
Audio, Subtitle and DVD menu
language
You can choose your own preferred language or
soundtrack from audio, subtitles and DVD menu
languages. If the language selected is not available
on the disc, the disc’s default language will be used
instead.
OSD language
: English
Subtitle : Auto
Language
Video
Audio
Misc
Rating
DVD Menu
Audio
English
French
Spanish
APress SETUP.
BPress /to select { Language }, then press .
CPress /to highlight one of the options below,
then press .
{ Subtitle }
Select this to change the subtitle language.
{ Audio }
Select this to change the disc soundtrack language.
{ DVD Menu }
Select this to change the language of the disc menu.
DUse /to select a language and press OK to
conrm.
ERepeat steps C- Dfor other language settings.
IMPORTANT!
-DVD discs and players are designed with regional
restrictions. Before playing a disc, make sure the
disc is for the same zone as your player.
-If ' 'appears on the TV screen when a button is
pressed, it means the function is not available on
the current disc or at the current time.
Playable discs
Using this DVD player, you can playback on the
following discs. Some of these discs may be
incompatible.
DVD Videodisc(DigitalVersatileDisc)
DVD+R/RW (DVD Recordable / Re-
 writable),DVD+RDL(Duallayer)
Audio/Video formats or MP3/
 JPEGles.
CD-R(CD-Recordable)
Audio/Video format or
 MP3/JPEGles.
Getting Started/Playback from disc
Helpful hint: Press to go back to previous menu item.
Press SETUP to exit the menu item.

13
English
CD-RW(CD-Rewritable)
Audio/Video format or
 MP3/JPEGles.
Audio CD (Compact Disc
 DigitalAudio)
Video CD
 (Formats1.0,1.1,2.0)
Super Video CD
MP3-Disc
is a trademark of DVD Format/Logo Licensing
Corporation.
Because of problems and errors that can occur
during the creation of DVD and CD software and/or
the manufacture of DVD and CD discs, Toshiba
cannot assure that this DVD player will successfully
play every disc bearing the DVD and CD logos. If you
happen to experience any difficulty playing a DVD
and/or CD disc on this DVD player, please contact
Toshiba Customer Service.
This DVD player requires discs/recordings to meet
certain technical standards in order to achieve
optimal playback quality. There are many different
types of recordable disc formats (including CD-R
containingMP3files).Notallrecordablediscswill
operate or produce optimal playback quality. The
technical criteria set forth in this owner's manual are
meantonlyasaguide.UseofCD-RWforMP3les
is not recommended.
You must obtain any required permission from
copyright owners to download or use copyrighted
content. Toshiba cannot and does not grant such
permission.
Supported Formats
MP3 tracks
 -Theleextensionshastobe'.mp3 '.
-JPEG/ISO format.
-Maximum 15 characters display.
-Supported sampling frequencies & corresponding
bit-rates;
32kHz, 64-320 kbps
44.1kHz, 48kHz 80-320 kbps
JPEG/Pictures
 -Theleextensionshastobe'.JPG 'and not
'.JPEG' .
-JPEG/ISO format.
-Maximum of 5760×3840 resolution can be
supported.
 -Maximumlesize:10M.
-It can only display DCF-standard still pictures or
JPEG pictures such as TIFF.
Tips:
– Maximum 100 sessions for CD and 10 multi border
for DVD are supported.
– For DVD-R, DVD-RW multi border, only finalized
disc can be supported.
– For DVD+R and DVD+RW multi border both
nalized and unnalized disc cannot be supported.
Starting disc playback
ATurn on the TV and select the video input connected
to the DVD player.
BPress 2ON / STANDBY to turn on the DVD player.
CPress OPEN/CLOSE to open the disc tray.
DPlace a disc onto the disc tray with the label facing
up, then press OPEN/CLOSE.
 For double-sided discs, load the side which you
want to play facing up.
EPlayback may start automatically. If not, press PLAY/
PAUSE .
 If a disc menu appears on the TV, see page 14
'Using the disc menu'.
 If the parental control was activated for the
inserted disc, you have to enter your four-digit
password, see page 20.
 For more playback features, see pages 13 - 16.
Tips:
-Do not overturn the DVD player while disc loading,
playing or ejecting.
-Do not close the disc tray manually even if the
power is switched off.
Basic playback control
Unless otherwise stated, all operations described are
based on Remote Control use.
Pausing playback
ADuring playback, press PLAY/PAUSE to pause
playback and display a still picture.
 Sound will be muted.
BTo resume normal playback, press PLAY/PAUSE
again.
Skipping chapter/track
Press PREV / NEXT to go to the previous
or next chapter/track during playback.
 When PREV ispressedaftertherst5
seconds of playback, playback will start from the
beginning of the current chapter/track. If you press
thebuttonwithintherst5seconds,playbackwill
start from the beginning of the preceding chapter/
track.
  Press DISPLAY to display the disc
information for title/chapter/track.
  Use Number buttons to enter valid chapter / track
number directly. For the track/chapter numbers which
are greater than ＂9＂, use ＂+10＂button. Each
presses increases the number by 10. Then press the
second digit of track/Chapter number.
 The playback skips to the selected chapter / track.
la
ybac Stopping playback
ADuring playback, press STOP .
The DVD player memorises the stopped point.
Playback from disc/Playback Feature
Helpful hint:SamediscscannotbeplayeronthisDVDplayerduetothecongurationandcharacteristics
of the disc, or due to the condition of recording and authorizing software

14
English
Press PLAY/ PAUSE to resume playback from the
location where you stopped playback.
If you press STOP again, the DVD player will
cancel the resume function.
Tips:
-Screen saver will start automatically if the disc
playback is stopped for about 2 minutes.
-The player will automatically switch to Power
Standby mode if you do not press any buttons for
about 22 minutes after the disc has stopped playing.
Program playback
During playback, press PROG, then the OSD will
appear as below:
For VCD:
Program
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
Play Clear Clear All
For DVD:
Program
Title 1
Title 2
Title 3
Title 4
Title 5
Title 6
Play Clear Clear All
AUse the /and OK button to select your desired
title/chapter/track in the list.
BWhenyouhavenishedprogramming,pressto
move the cursor to the 'Play', then press the OK
button or directly press PLAY/PAUSE button to
start the program playback.
CPress CLEAR or select ' Clear ' to delete one by one
from last chosen track / title /chapter or select 'Clear
All' to clear all the programmed tracks/titles.
DPress STOP twice to cancel program playback.
Operations for video playback (DVD/
VCD/SVCD)
Using the disc menu
Depending on the disc, a menu may appear on the
TV screen once you load in the disc.
To select a playback feature or item
 Use ///or number buttons on the remote
control, then press OK to start playback.
To access or remove the menu.
 Press MENU on the remote control.
Zooming In
This function allows you to enlarge the picture on the
TV screen and to pan through the enlarged picture.
ADuring playback, press ZOOM repeatedly to display
the picture with different scales.
 Use ///to pan through the enlarged picture.
 Playback will continue.
BPress ZOOM repeatedly to return to the original size.
Slow Motion
APress SLOW during playback to select the required
speed:1/2,1/4,1/8(forwardonly).
 Sound will be muted.
BTo return to normal speed, press PLAY/ PAUSE .
Forward/ Reverse Searching
You can fast forward or fast reverse a disc during
playback and select a desired search speed.
For DVD,VCD, SVCD,CD, MP3
ADuring playback, press F.R/ F.F to select the required
speed:X2,X4,X8,X16(backwardorforward).
Soundwillbemuted(DVD/VCD/SVCD/MP3)or
intermittent(CD).
BTo return to normal speed, press PLAY / PAUSE .
Selecting various repeat functions
Repeat play mode
The repeat play options vary depending on the disc
type.
AWhile playing a disc, press REPEAT repeatedly to
choose a repeat options.
For DVD
 -RepeatChapter(currentlyplayingchapter)
 -RepeatTitle(currentlyplayingtitle)
 -Off(cancel)
For Video CD, Audio CD
 -RepeatSingle(currentlyplayingtrack)
 -RepeatAll(entiredisc)
 -Off(cancel)
For MP3, JPEG
 -RepeatSingle(currentlyplayingle)
 -RepeatALL(currentfolder)
 -Off(cancel)
Tip:
-For VCD2.0/SVCD discs, repeat playback is not
possible if the PBC mode is turned on.
Repeating a section within a chapter/
track
 Youcanrepeattheplaybackofaspecicsegment
within a chapter or track. To do this, you must mark
the start and end of the segment you want.
Playback Feature
Helpful hint：The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.

15
English
AWhile playing a disc, press A - B at your chosen
starting point.
BPress A - B again at your chosen end point.
  The section will now repeat continuously.
CTo exit the sequence, press A - B.
Viewing the disc playback Information
You can view the disc information (such as current
title/chapter/track number, total playing time or
remainingtimeonthedisc)withoutinterruptingthe
disc playback.
ADuring playback, press DISPLAY repeatedly on the
remote control.
 The available disc information appears on the TV
screen with the following sequence.
Time
Time 00：03：33/01：24：46  (DVD)
Title
Title 1/1  (DVD)
Chapter
Chapter 2/8
Audio
Audio 1/1 6Ch  (DVD)
Subtitle
Subtitle 1/8 Eng  (DVD)
Angle
Angle 1/4  (DVD)
Time
Time 00：03：33/00：05：00  (VCD)
Track
Track 3/24  (VCDPBCOFF)
OR
Time
Time 00：03：33/00：05：00 (VCDPBCON)
PBC On  (VCDPBCON)
Title/Chapter/Track/Time selection
APress T-SEARCH, then press /to select
{ Time }, { Title }, { Chapter } or { Track }.
For VCD：
PBC OFF
Track ---
Time --:--:-- (desiredtimeofthecurrenttrack)
Disc Time --:--:-- (desiredtimeofthedisc)
For DVD:
Title ---
Chapter ---
Time --:--:-- (desiredtimeofthedisc)
BUsethenumberbuttons(0-9)toinputavalid
numberortime(suchas00:34:27).(Thisfunction
onlyapplytoDVD/VCD/CD/SVCD.)
CPressOKtoconrm.
 The playback skips to the selected title/chapter/
track/time.
Angle
  When {Angle} information appears on the screen,
press A N G L E b u t t o n o n t h e r e m o t e c o n t r o l
repeatedly to switch between different angles.
Playback Feature
 Playback will go to the selected angle.
Special DVD Features
Playing a Title
APress TITLE.
The disc title menu appears on the TV screen.
BUse ///ornumberbuttons(0-9)toselecta
play option.
CPressOKtoconrm.
Changing the Audio Language
For DVD：
Press AUDIO repeatedly to select different audio
languages.
Changing the Audio Channel
For VCD：
 Press AUDIO to select the available audio channels
providedbythedisc(Left,Right,Mix,Stereo).
Subtitles
Press SUBTITLE repeatedly to select different
subtitle languages.
Special VCD and SVCD Features
For VCD with Playback Control ( PBC ) feature
(version 2.0 only)
 Press MENU to toggle between 'PBC On 'and '
PBC Off '.
If you select 'PBC On ', the disc menu ( if
available)willappearontheTV.
Usethenumberbuttons(0-9)toselectaplay
option.
 Press PREV / NEXT to go to the previous
or next track.
 When PREV ispressedaftertherst5
seconds of playback, playback will start from the
beginning of the current track. If you press the button
withintherst5seconds,playbackwillstartfromthe
beginning of the preceding track.
 During playback, pressing RETURN will return to
themenuscreen(ifPBCison).
If you want to skip the index menu and playback
directly from the beginning.
 Press MENU on the remote control to turn the PBC
off.
Helpful hint：The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.

16
English
Playback Feature
original view list.
CSelect Add To Program in the toolkit then press
OK. ' √'will disappear from screen. It means that the
les/tracksyouhaveselectedalreadyaddedintothe
Program View list.
DSelect Program View in the toolkit then press OK to
openthele/trackintheProgramViewlistthatyou
already selected in step B.
EPress PLAY / PAUSE toplaybackallles/tracks
in the Program View list.
The Toolkit has the following play mode items:
Filter ( Audio/Photo/Video ):Setslelters
Repeat (Off/Single/ All):
Off: Resumes normal playback
Single:Repeatsthecurrenttrack/le.
All: Repeatsalllesonthecurrentfolderorall
tracks on the disc.
Mode(Normal/Shufe)
This mode can also be toggled by using RANDOM
button.
Normal: Resumes Normal playback
 Shufe:Playbackstrack/leinrandomorder.
Edit Mode: Program operation works only when
 EditModeisselected.Afternishedstoringtheles/
tracks you want into the Program View list, select
“Edit Mode” again and press OK to release edit
mode.
Program View:Toviewtracks/lesinthe
Program View list. It is disabled if the Program View
list is empty.
Add To Program:Addles/trackstotheProgram
View list. It is disabled if Edit Mode is not selected.
(Themaximumnumberofles/trackscanbeadded
is30.)
Browser View:Toviewles/tracksintheOriginal
View list.
Clear Program:Deletetheles/tracksinthe
Program View list.
Selectale/trackormoreyouwanttodeletein
stop mode.'√'willappearbesidesthedeletedle/
track.Select Clear Program and then press OK . It is
disabled if Edit mode is not selected.
Zoom picture ( JPEG)
During playback, press ZOOM repeatedly to
display the picture with different scales.
Use / / / to view the zoomed picture.
Rotate picture (JPEG)
During playback, press / / / to rotate the
picture on the TV screen.
/ ：ipthepictureverticallyby180º
 ：rotatethepictureanti-clockwiseby90º
 ：rotatethepictureclockwiseby90º
Helpful hint：The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.
Playing MP3/JPEG/ Kodak picture CD
IMPORTANT!
You have to turn on your TV and set to
the correct Video In channel. (See page
11, ‘ Finding your viewing channel ‘ ).
General Operation
ALoad a disc.
 The disc reading time may exceed 30 seconds
duetothecomplexityofthedirectory/le
conguration.
 ThedatadiscmenuandID3(MP3)information
(includingatleasttitle,singerandalbum)appears
on the TV screen.
BPress / to select the folder and press OK to
open the folder.
CPress / toselectatrack/le.
DPress OKtoconrm.
Tips:
- If you highlight on a jpeg le, a preview will appear.
- During MP3 playback, the LED will display the track
number.
- During JPEG playback, the LED will display the le
number.
Playback Selection
During playback, you can;
Press PREV / NEXT to select the
previous/nexttrack/leinthecurrentfolder.
Press PLAY/PAUSE repeatedly to pause/
resume playback.
For MP3
Withintherst5seconds,pressPREV to go
back to the previous track.
Aftertherst5secondsofplayback,pressPREV
to go back to the beginning of current track.
During playback, press / to access fast
forward or fast reverse with the required speed: X2,
X4, X8, X16.
Play modes for MP3/Audio CD/JPEG
You are able to modify the play modes through the
toolkit which appears on the right of below picture
on the screen. Press / to navigate between the
windows and / buttonstoselectles/tracksor
play mode items. Then press OK . Please refer to
belowstepstoplaybackles/tracksinthe Program
View list:
ASelect Edit Mode in the toolkit then press OK to
start edit mode.
B Selectale/trackormoreles/tracksyouwantinthe

17
English
DVD Menu Options
Using the Video setup menu
APress SETUP on the remote control.
 The system setup menu appears.
Aspect Ratio :
View Mode :
4:3
Auto Fit
Aspect Ratio :
View Mode :
4:3
Auto Fit
Aspect Ratio :
View Mode :
4:3
Auto Fit
Video Out
Smart Picture :
:S-VIDEO
Standard
Language
Video
Audio
Misc
Rating
BPress / to select { Video }, then press 
CPress / to select an item, then press to
access.
Example: { Video Out }
 The options for the selected item appears.
 If the selection in the menu is greyed out, that
means the feature is not available or not possible to
change at the current state.
DUse / to select a setting and press OK to
 conrm.
Example: { P-Scan }
 The setting is selected and setup is completed.
ETo exit, press SETUP.
Aspect Ratio
 ThepictureshapecanbeadjustedtotyourTVand
the format must be available on the playback disc.
Otherwise, the TV display will not affect the picture
during playback.
AIn ' Video ', press / to select {Aspect Ratio },
then press .
{ 4:3 }
Select this if you have a normal TV. A 'wide-screen'
source display with black bars on the top and bottom
will be displayed on the TV screen.
{ 16:9 }
 Selectthisforwide-screenTV(frameratio16:9).
BUse / to select a setting and press OK to
 conrm.
View Mode
UseviewmodetoscaleanimagethattstotheTV
screen's width and height.
AIn ' Video ', press / to select { View Mode },
then press .
{ Fill }
Fill the screen with decoded image.
{ Original }
Display image as its original size.
{ Height Fit }
Fit the screen height with image height.
{ Width Fit }
Fit the screen width with image width.
{ Auto Fit }
 Automaticallytthedecodedimageonscreen
Tip:
-It may not be possible to play certain MP3/JPEG
disc due to the conguration and characteristics of
the disc or condition of the recording.
This DVD Player setup is carried out via the TV,
enabling you to customise the DVD player to suit
your particular requirement.
Using the Language setup menu
APress SETUP on the remote control.
  The system setup menu appears.
OSD language :
Subtitle :
:
Audio
:
DVD Menu
English
Auto
English
English
Language
Video
Audio
Misc
Rating
BPress / to select {Language }, then press .
CPress / to select an item, then press to
access.
Example: { OSD Language }
 The options for the selected item appears.
 If the selection in the menu is greyed out, that
means the feature is not available or not possible to
change at the current state.
DUse /to select a setting and press OK to
conrm.
Example: { English }
The setting is selected and setup is completed.
ETo exit, press SETUP.
OSD Language
This menu contains various language options for the
language displayed on the screen.
Subtitle/Audio/DVD Menu Subtitle
These menus contains various language options
for audio, subtitle, and DVD menu which may be
recorded on the DVD.
Tips:
-Some DVD video discs may be set to display
subtitles in a different language other than
you selected. A prior subtitle language may be
programmed on the disc.
-Some DVD video discs allow you to change subtitle
selections only via the disc menu. If this is the case,
press the MENU button and choose the appropriate
subtitle language from the selection on the disc
menu.
-Some DVD video discs may not be played in a
different audio language that you selected. A prior
language may be programmed on the disc.
-Some DVD discs may not include your pre-selected
language . In this case, the DVD player
automatically displays discs menus consistent with
the disc’s initial language setting.
Helpful hint: Press to go back to previous menu item.
Press SETUP to exit the menu item.

18
English
DVD Menu Options
without distortion.
{ Pan Scan }
Automatically display decoded image on full screen
without distortion.
BUse / to select a setting and press OK to
 conrm.
Tip:
-Depending on the type of disc, you may not be able
to view the mode as selected.
Video Out
The video output of the DVD player can be selected
as “ S-VIDEO “ , “ Component “ or “ P-Scan”.
AIn ＇Video＇, press / to select { Video Out },
then press .
{ S-VIDEO }
 SelectthisforVideo(CVBS)orS-Videoconnection.
{ Component }
Select this for component video connection.
{ P-Scan }
Select this when you connect your DVD player to
your TV, which has component video inputs that
supports progressive scan.
BUse / to select a setting and press OK to
conrm.
Smart Picture
ThisDVDplayerprovidesfourpredenedsetsof
picture color settings.
AIn ' Video ', press / to select {Smart Picture },
then press .
{ Standard }
Select this for a preset standard picture setting.
{ Vivid }
Select this to make the picture brighter.
{ Cool }
Select this to make the picture softer.
{ Personal }
Select this to personalize your picture color by
adjusting the brightness, contrast, tint and color
(saturation).
BUse / to select a setting and press OK to
 conrm.
CIf you select { Personal }, then proceed to steps
D~G.
 The setup menu appears.
Brightness
Contrast
Tint
Color
0
0
0
0
Close
DPress / to highlight one of the following options.
Brightness
Increase the value to brighten the picture or vice
versa.Choosezero(0)foraveragesetting.
Contrast
Increase the value to sharpen the picture or vice
versa.Choosezero(0)tobalancethecontrast.
Tint
Increase the value to darken the picture or vice
versa.Choosezero(0)foraveragesetting.
Color
Increase the value to enhance the color in your
pictureorviceversa.Choosezero(0)tobalancethe
color.
EPress / to adjust the setting that best suits
your personal preference.
FRepeat steps D~ Eto adjust your picture
preference.
GPress / to select ＇Close＇and press OK to
conrm.
Using the Audio setup menu
APress SETUP on the remote control.
 The system setup menu appears.
:
:
:
Digital Output
Night Mode
Down Sampling
All
Off
On
Language
Video
Audio
Misc
Rating
:
3D Effects Off
BPress / to select { Audio }, then press .
CPress / to select an item, then press to
access.
Example: { Night Mode }
 The options for the selected item appears.
 If the selection in the menu is greyed out, that
means the feature is not available or not possible to
change at the current state.
DUse / to select a setting and press OK to
 conrm.
Example: { On }
 The setting is selected and setup is completed.
ETo exit, press SETUP.
Digital Output
Select this if you connect to a multichannel decoder/
receiver.
AIn 'Audio', press / to select { Digital Output },
then press .
{ All }
Select this if the connected device has a built-in
multichannel decoder that supports one of the
 multichannelaudioformat(DolbyDigital,DTS).
{ PCM }
Select this if the connected device is not capable of
decoding multichannel audio. The DVD player will
convert the Dolby Digital signal to PCM (Pulse Code
Modulation).
{ Off }
To deactivate the digital audio output. For example, if
you use the AUDIO OUT jacks to connect to a TV or
stereo system.
BUse / to select a setting and press OK to
conrm.
Tip:
-When playing MPEG, MP3 and set Digital Output to
{ALL}, the player will output PCM signals.
Helpful hint: Press to go back to previous menu item.
Press SETUP to exit the menu item.

19
English
Night Mode
This mode optimizes playback of sound at low
volume. High volume outputs will be softened and
low volume outputs are brought upward to an audible
level.
AIn ＇ Audio＇, press / to select { Night Mode },
then press .
{ On }
Select this to set low volume output. This feature
is only available for movie discs with Dolby Digital
mode.
{ Off }
Turns off night mode feature. Select this to enjoy the
surround sound with its full dynamic range.
BUse / to select a setting and press OK to
 conrm.
Down Sampling
You can enable and disable the digital signal for
better sound output quality.
AIn ＇Audio＇, press / to select { Down
Sampling }, then press .
{ Off }
 Ifyouramplier/decoderiscompatiblewith96KHz
PCM, select “ Off “ . Sound is sampled at 96 KHz.
{ On }
Ifyouramplier/decoderisnotcompatiblewith96
KHz PCM, select “ On “ . Sound recorded at 96 KHz
is down sampled to 48 KHz.
BUse / to select a setting and press OK to
 conrm.
Tip:
- When playing back disc with copyright protection,
the sound will be down sampled to 48 KHz even
when you select Down Sampling off.
3D Effects
To obtain expansive virtual surround sound effects
from two speakers, set 3D Effects to on. This
enhancement sounds only output from the Analog
AUDIOOUT(L/R)jacksoftheDVDplayer.
AIn 'Audio', press / to select { 3D Effects }, then
press .You can set to { Off } or { On }.
BUse / to select a setting and press OK to
 conrm.
Tip:
- Only effective in playback of a DVD Video disc with
Dolby Digital 5.1 bitstream.
Using the Rating setup menu
APress SETUP on the remote control.
The system setup menu appears.
Parental control : 8.Aduit
Set Password
Language
Video
Audio
Misc
Rating
BPress / to select {Rating }, then press .
DVD Menu Options
Helpful hint: Press to go back to previous menu item.
Press SETUP to exit the menu item.
CPress / to select an item, then press to
access.
Example: { Parental control }
 The options for the selected item appears.
 If the selection in the menu is greyed out, that
means the feature is not available or not possible to
change at the current state.
DUse / to select a setting and press OK to
 conrm.
Example: { 8 Adult }
 The setting is selected and setup is completed.
ETo exit, press SETUP.
Rating Level settings
Depending on the DVD, you may be asked to
change the parental level while playing the disc. The
rating levels are from 1 to 8 and are country
dependent. You can prohibit the playing of certain
discs that are not suitable for your children, or have
certain discs played with alternative scenes.
AIn ' Rating ', press / to select {Parental control },
then press .
BUse the number buttons to enter the four-digit
password, then press OK.(See ‘Changing the
Password’onpage20.)
CPress OK again to list the parental level.
{ 1.Kid Safe }
Suitable for children.
{ 2. G }
General Audience; recommended as acceptable for
viewers of all ages.
{ 3. PG }
Parental Guidance suggested.
{ 4. PG-13 }
Unsuitable for children under 13.
{ 5. PG-R }
Parental Guidance Recommended.
{ 6. R }
Restricted; under 17 requires accompanying parent
or adult guardian.
{ 7. NC-17 }
No one under 17 admitted.
{ 8. Adult }
 DVDsoftwaresofanygrades(adult/general/children)
can be played back. Should be viewed only by adults
due to graphic sexual material, violence or language.
DUse / to select a rating level and press OK to
conrm.
 Select { 8 Adult } to disable parental level and
allow all discs to play.
DVDs that are rated higher than the level you
selected will not play unless you enter your four-digit
password.
Tips:
-This feature will not limit viewing if the disc
manufacturer did not code the disc.
-VCD, SVCD, CD have no level indication, so
parental control has no effect on these type of discs.
This also applies to most illegal DVDs.
-Some DVDs are not coded with a rating though the
movie rating may be printed on the disc cover. The
rating level feature does not prohibit play of such
discs.