Toshiba SD-340ESE User manual

2
18
26
34
53
62
Introduction
Connections
Basic playback
Advanced playback
Function setup
Others
DVD VIDEO PLAYER
SD-340ESE
SD-340ESB
OWNER’S MANUAL
DIGITAL VIDEO
© 2004Toshiba Corporation

2
Introduction
Model No. Serial No.
Retain this information for future reference.
The following information applies only to the model for U.K.
SAFETY PRECAUTIONS
In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD player.
CLASS 1
LASER PRODUCT
WARNING: TO REDUCETHE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSETHIS
APPLIANCETO RAIN OR MOISTURE. DANGEROUS HIGHVOLTAGES ARE PRESENT
INSIDETHE ENCLOSURE. DO NOT OPENTHE CABINET. REFER SERVICINGTO
QUALIFIED PERSONNEL ONLY.
CAUTION: This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for
future reference. Should the unit require maintenance, contact an authorized service location -
see service procedure.
Use of controls of adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible laser radiation may be present when the enclosure is opened.
DO NOT STARE INTO BEAM.
General Information
If the socket outlets in your home are not suitable for the plug supplied with this unit,
the plug must be cut off and an appropriate one fitted.
The plug severed from this mains lead must be destroyed as it is hazardous if
inserted into a live socket.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code:
BLUE: NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this unit may not correspond with
the coloured markings identifying the terminals in your plug, proceed as follows:
The wire that is coloured blue must be connected to the terminal in the plug
which is marked with the letter N or coloured black.
The wire that is coloured brown must be connected to the terminal which is
marked with the Letter L or coloured red.
Do not connect either wire to the earth terminal which is marked by the letter E or by
the safety earth symbol or coloured green or green-and-yellow.
Use a 5A fuse which is approved by ASTA or BSI to BS1362.
Always replace the fuse cover after changing the fuse.

3
Introduction
Location of the required label
The rating plate and the safety caution are
on the rear of the unit.

4
Introduction
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALLWARNINGS AND INSTRUCTIONS GIVEN INTHIS
OWNER’S MANUAL ANDTHOSE MARKED ONTHE UNIT. RETAINTHIS BOOKLET FOR
FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard.The safeguards incorporated in this unit will protect you if you observe the following
procedures for installation, use and servicing.This unit is fully transistorized and does not contain any parts that
can be repaired by the user.
DO NOT REMOVETHE CABINET COVER, ORYOU MAY BE EXPOSEDTO DANGEROUSVOLTAGE.
REFER SERVICINGTO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.

5
Introduction
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
10.Only use attachments/accessories specified by the manufacturer.
11.Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus.When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
S3125A
12.Unplug this apparatus during lightning storms or when unused for long periods of time.

6
Introduction
IMPORTANT SAFETY INSTRUCTIONS
13.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
14.When you use headphones, keep the volume at a moderate level.If you use the headphones continuously
with high volume sound, it may cause hearing damage.
15.Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a
risk of fire or electric shock.
16.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
ADDITIONAL SAFETY INSTRUCTIONS
17.Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious
personal injury.

7
Introduction
18.Do not place a heavy object on or step on the apparatus.The object may fall, causing serious personal
injury and serious damage to the apparatus.
19.Do not use a cracked, deformed, or repaired disc.These discs are easily broken and may cause serious
personal injury and apparatus malfunction.

8
Introduction
Precautions
Notes on handling
When shipping the DVD video player, the original
shipping carton and packing materials come in handy.
For maximum protection, repack the unit as it was
originally packed at the factory.Take care not to give
it a shock or shake when carrying.
Do not use volatile liquids, such as insect spray, near
the DVD video player. Do not leave rubber or plastic
products in contact with the DVD video player for a
long time.They will leave marks on the finish.
The top and rear panels of the DVD video player may
become warm after a long period of use.This is not a
malfunction.
When the DVD video player is not in use, be sure to
remove the disc and turn off the power.
If you do not use the DVD video player for a long
period, the unit may not function properly in the
future.Turn on and use the DVD video player
occasionally.
Notes on locating
Place the DVD video player on a level surface.Do not
use it on a shaky or unstable surface such as a
wobbling table or inclined stand.The loaded disc may
come off the proper position and cause damage to
the DVD video player.
When you place this DVD video player near aTV,
radio, or VCR, the playback picture may become poor
and the sound may be distorted. In this case, place
the DVD video player away from the TV, radio, or
VCR.
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe.Use a dry cloth to wipe
it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the DVD
video player.
If you use a chemical saturated cloth to clean the
unit, follow that product’s instructions.
To obtain a clear picture
The DVD video player is a high technology, precision
device. If the optical pick-up lens and disc drive parts
are dirty or worn down, the picture quality becomes
poor.To obtain a clear picture, we recommend regular
inspection and maintenance (cleaning or parts
replacement) every 1,000 hours of use depending on
the operating environment.For details, contact your
nearest dealer.
Notes on moisture condensation
Moisture condensation damages the DVD video
player. Please read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts of
the DVD video player.
Moisture condensation occurs during the
following cases.
When you bring the DVD video player directly from a
cold place to a warm place.
When you use the DVD video player in a room where
you just turned on the heater, or a place where the
cold wind from the air conditioner directly hits the
unit.
In summer, when you use the DVD video player in a
hot and humid place just after you move the unit from
an air conditioned room.
When you use the DVD video player in a humid place.
Do not use the DVD video player when moisture
condensation may occur.
If you use the DVD video player in such a situation, it
may damage discs and internal parts.Remove the
disc, connect the power cord of the DVD video player
to the wall outlet, turn on the DVD video player, and
leave it for two or three hours.After two or three
hours, the DVD video player will have warmed up and
evaporated any moisture.Keep the DVD video player
connected to the wall outlet and moisture
condensation will seldom occur.

9
Introduction
Notes on Discs
On handling discs
Do not touch the playback side of the disc.
Do not attach paper or tape to discs.
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration.Wipe the disc from the center
outwards with a soft cloth.Always keep the disc
clean.
If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs.It may damage the disc.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
Playback side
DVD video disc
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3
Track 1 Track 2 Track 3 Track 4 Track 5
Structure of disc contents
Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters.VIDEO CDs and
audio CDs are divided into tracks.
DVD video disc
VIDEO CD/audio CD
Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.
Notes on copyright
It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, and rent copyrighted
material without permission.
DVD video discs are copy protected, and any
recordings made from these discs will be distorted.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.
VIDEO CD/audio CD

10
Introduction
Playable discs
This DVD video player can play the following discs.
• You cannot play discs other than those listed above.
• You cannot play DVD-RAM discs or
non-standardized discs, etc., even if they may be
labeled as above.
• This DVD video player uses the NTSC/PAL color
system, and cannot play DVD video discs recorded in
any other color system (SECAM, etc.).
Notes on Discs (continued)
DVD
video
discs
Disc Mark Contents
Disc
Size Maximum
playback time
VIDEO
CDs
Approx.4 hours
(single sided disc)
Approx.8 hours
(double sided disc)
Approx.80 minutes
(single sided disc)
Approx.160 minutes
(double sided disc)
Approx.74 minutes
Approx.20 minutes 8 cm
12 cm
8 cm
12 cm
Audio
+
video
(moving
pictures)
Audio
+
video
(moving
pictures)
Audio
CDs
Approx.74 minutes
Approx.20 minutes
8 cm
(CD
single)
12 cm
Audio
The following discs are also available.
DVD-R discs of DVD video format
CD-R/CD-RW discs of CD-DA format
Some of these discs may be incompatible.
DIGITAL VIDEO
About this owner’s manual
This owner’s manual explains the basic instructions of
this DVD video player. Some DVD video discs are
produced in a manner that allows specific or limited
operation during playback.As such, the DVD video
player may not respond to all operating commands.This
is not a defect in the DVD video player. Refer to
instruction notes of discs.
“ ” may appear on theTV screen during operation.
A “ ” means that the operation is not permitted by the
DVD video player or the disc.
Notes on region numbers
The region number of this DVD video player is 2.If
region numbers, which stand for their playable area, are
printed on your DVD video disc and you do not find
or , disc playback will not be allowed by the player.
(In this case, the DVD video player will display a
message on-screen.)
OnVIDEO CDs
This DVD video player supports VIDEO CDs equipped
with the PBC (Version 2.0) function.(PBC is the
abbreviation of Playback Control.)You can enjoy two
playback variations depending on types of discs.
• VIDEO CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this DVD video
player in the same way as an audio CD.
• VIDEO CD equipped with PBC function
(Version 2.0)
In addition to operation of a VIDEO CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.

11
Introduction
Table of Contents
Introduction
SAFETY PRECAUTIONS .......................... 2
IMPORTANT SAFETY INSTRUCTIONS ... 4
Precautions .............................................. 8
Notes on Discs ......................................... 9
Notes on region numbers............................... 10
Table of Contents ................................... 11
Identification of Controls....................... 12
Front panel ..................................................... 12
Rear panel...................................................... 12
DVD display .................................................... 13
Remote control ............................................... 14
Loading batteries ........................................... 15
Operating with the remote control .................. 15
Connections
Connecting to aTV................................. 18
Connecting to a TV......................................... 18
Connecting to an audio system and TV
equipment with component video jacks ....... 19
Connecting to Optional Equipment ...... 20
Connecting to an amplifier equipped with a
Dolby Digital decoder................................... 21
Connecting to an amplifier equipped with
Dolby Surround Pro Logic............................ 21
Connecting to an amplifier equipped with a
DTS decoder ................................................ 22
Connecting to an amplifier equipped with an
MPEG2 audio decoder................................. 22
Connecting to an amplifier equipped with a
digital audio input......................................... 23
Basic playback
Playing a Disc......................................... 26
Basic playback ............................................... 26
Variable Speed Playback ....................... 28
Playing in fast reverse or fast forward
directions...................................................... 28
Playing frame by frame .................................. 28
Playing in slow-motion ................................... 29
Resuming playback from the same location .. 29
Locating a Desired Section ................... 30
Locating a title using the top menu ................ 30
Locating a desired section by entering the
corresponding number ................................. 31
Locating a specific chapter or track ............... 31
Advanced playback
Accessing a Specific Location Directly ... 34
Entering the time counter of the desired
location......................................................... 34
Repeating a Specific Segment .............. 35
Repeating a specific segment ........................ 35
Playing in aVaried Order ....................... 36
Playing titles, chapters or tracks in a varied
order.............................................................36
Playing in a Favourite Order.................. 37
Setting titles, chapters, or tracks in a favourite
order.............................................................37
Zooming a Picture.................................. 38
Zooming a picture .......................................... 38
Selecting the Picture Enhancement
(E.P.M.) .................................................... 39
Selecting the picture enhancement................ 39
Selecting the Sound Enhancement
(E.A.M.) ................................................... 40
Selecting the sound enhancement................. 40
Selecting the Camera Angle.................. 41
Changing the camera angle ........................... 41
Selecting Subtitles ................................. 42
Selecting a subtitle language ......................... 42
Selecting a Language ............................ 43
Selecting a playback audio setting................. 43
On-screen Display Operation................ 44
On-screen display operation ..........................44
Playing MP3/WMA Files ......................... 46
Playing MP3/WMA files ..................................46
Viewing JPEG Files................................ 48
Starting from a thumbnail view.......................48
Viewing DivXTM / MPEG-4 Files.............. 49
Playing DivXTM / MPEG-4 files........................49
Function setup
Customizing the Function Settings ...... 53
Setting procedure...........................................54
Setting details................................................. 55
Table of Languages................................ 61
Others
Before Calling Service Personnel ......... 64
Specifications......................................... 65

12
Introduction
Identification of Controls
See the page in for details.
Front panel
Rear panel
TOP MENU button
MENU button
RETURN button
ENTER button
13
30
60
30
When connecting the optical digital cable, remove
the cap and fit the connector into the jack firmly.
When not using the jack, keep the cap inserted to
protect it from dust intrusion.

13
Introduction
DVD
VCD
TITLETOTAL
CHPGROUP TRK
MA
-
B
R
MR
DVD display
The indicators vary depending on the kinds of discs you play.
DVD video disc VIDEO CD Audio CD
• During playback:
Example
Playing chapter 3 of title 2
Some discs may not display chapter
numbers or elapsed time.
• During playback:
Example
Playing track 6
Some discs may not display track
numbers or elapsed time.
• During playback:
Example
Playing track 6
Play mode
indicator
Total playing
time indicator
Chapter number
indicator
Track number
indicator
Memory playback indicator
Random (shuffle)
playback indicator
DVD / VIDEO CD /
CD indicator
Multifunctional indicator (indicates
operating status or messages, etc.) Angle icon
indicator
Repeat playback
indicator
Title number
indicator
DVD
TITLE
CHP
VCD
TRK
CD
TRK
When you start playback, the elapsed time indicators appear. Pressing the FL.SELECT button switches
them to the title/chapter/track number indicators. Some discs may not permit this operation.

14
Introduction
Identification of Controls (continued)
The instructions in this manual describe the functions on the remote control. See the page in for details.
Remote control
* MENU button
Use the MENU button to display the menu included on
many DVD video discs.To operate a menu, follow the
instructions in “Locating a title using the top menu.”
30
FL.SELECT button
MENU
MENU button *
FL.SELECT
37
42
41
43
45
40
54
38
39
35
36

15
Introduction
Open the cover.
Insert batteries (R03 size).
Make sure to match the + and – on the batteries
to the marks inside the battery compartment.
Notes on batteries
Improper use of batteries may cause battery leakage and
corrosion.To operate the remote control correctly, follow the
instructions below.
• Do not insert batteries into the remote control in the
wrong direction.
• Do not charge, heat, open, or short-circuit the batteries.
Do not throw batteries into a fire.
• Do not leave dead or exhausted batteries in the remote
control.
• Do not use different types of batteries together, or mix old
and new batteries.
• If you do not use the remote control for a long period of
time, remove the batteries to avoid possible damage from
battery corrosion.
• If the remote control does not function correctly or if the
operating range becomes reduced, replace all batteries
with new ones.
• If battery leakage occurs, wipe the battery liquid from the
battery compartment, then insert new batteries.
1
Operating with the remote control
Point the remote control at the remote
sensor and press the buttons.
Distance: About 7 m (23 feet) from the front of the
remote sensor
Angle: About 30° in each direction of the front of
the remote sensor
* Do not expose the remote sensor of the DVD video
player to a strong light source such as direct
sunlight or other illumination. If you do so, you may
not be able to operate the DVD video player via the
remote control.
Notes on the remote control
• Direct the remote control at the remote sensor of the DVD
video player.
• When using the remote control, press the buttons at
intervals of about 1 second to ensure the correct mode of
operation.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot or
humid place.
• Do not spill water or put anything wet on the remote
control.
• Do not open the remote control.
2
Loading batteries

Connections
Read this chapter first to make all necessary
preparations.
Connecting to aTV
(Using the SCART socket)
Connecting to aTV
(Using the phone type jacks)
Connecting to aTV
(Using the component video
jacks)
Connecting to an amplifier
equipped with a Dolby Digital
decoder
Connecting to an amplifier
equipped with Dolby Surround
Pro Logic
Connecting to an amplifier
equipped with a DTS decoder
Connecting to an amplifier
equipped with an MPEG2 audio
decoder
Connecting to an amplifier
equipped with a digital audio
input

18
Connections
To audio
input To audio input
(yellow)
Normal TV
Audio cable
To VIDEO
OUT
(yellow) To 2ch AUDIO OUT
(R: red, L:white)
To AV
To SCART input
SCART cable
Normal TV
Connecting to a TV
Connect the DVD video player to your TV.
For details of output sound, see
43
.
Connecting to aTV (Using the SCART socket)
• Make the following setting.
On-screendisplay Select:
Page
“VideoOutput” CVBS
RGB
*YUV
* With progressive scan off.
• Make the following setting.
On-screendisplay Select:
Page
“PCM”or “Raw”“Digital Out”
“VideoOutput” CVBS
RGB
*YUV
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD video player to your TV, be sure to turn off the power and unplug both units from the wall outlet
before making any connections.
• If your television set has one audio input, connect the left and right audio outputs of the DVD video player to a Y cable
adapter (not supplied) and then connect to your TV.
• Connect the DVD video player directly to your TV. If you connect the DVD video player to a VCR, TV/VCR combination or
video selector, the playback picture may be distorted as DVD video discs are copy protected.
• Analog audio out will not have sound if DTS playback is selected.
Connecting to aTV (Using a phono type jacks)
* With progressive scan off.
54 58
54
54
59
58

19
Connections
Connecting to aTV (Using the component video jacks)
• Make the following setting.
On-screendisplay Select:
Page
Digital Out
Video output
PCM or Raw
YUV
Switching the output signal (interlaced/
progressive) using the remote control
You can temporarily switch the output signal for better
picture quality.
Press PROGRESSIVE on the remote control during stop
mode.
Press PROGRESSIVE again to turn off progressive mode.
Notes
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
• If you place the DVD video player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD
video player away from the tuner and radio.
• The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, high volume sound may damage your hearing as well as the speakers.
• Turn off the amplifier before you connect or disconnect the DVD video player’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
• Progressive can be on/off only when video output is set to YUV.
58
• When Progressive is on, only component video will be output.
• When the TV system is set to PAL mode, all output will be forced to PAL type (e.g. 625p, 625i, etc.).
58
• When the TV system is set to NTSC mode, all output will be forced to NTSC type (e.g. 525p, 525i, etc.).
58
• Analog audio out will not have sound if DTS playback is selected.
Interlaced outputs/inputs
SomeTVs or monitors are equipped with component video inputs.
Connecting to these inputs allows you to enjoy higher quality picture
playback.
Actual labels for component video inputs may vary depending on the
TV manufacturer.(ex.Y, R-Y, B-Y orY, CB, CR)
In someTVs or monitors, the color levels of the playback picture may
be reduced slightly or the tint may change.In such a case, adjust the
TV or monitor for optimum performance.
Progressive outputs/inputs
SomeTVs or monitors are equipped with component video inputs that
are capable of reproducing a progressively scanned video signal.
Connecting to these inputs allows you to view the highest quality
pictures with less flicker.
Consumers should note that not all high definition television sets are
fully compatible with this product and may cause artifacts to be
displayed in the picture.In case of 525 or 625 progressive scan
picture problems, it is recommended that the user switch the
connection to the “standard definition”output.If there are questions
regarding ourTV set compatibility with this model 525p and 625p DVD
player, please contact our customer service center.
Audio cable
To audio
input
ToY video input
To PBvideo
input
To PRvideo
input
To 2ch AUDIO OUT
(R: red, L:white)
54
54
59
58

20
Connections
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD video player
to optional audio equipment.
Warning
• When you are connecting (via the OPTICAL or
COAXIAL DIGITAL AUDIO OUT jack) an AV decoder
that does not have Dolby Digital, Digital Theater
Systems (DTS) or MPEG2 decoding function, be sure
to set “Digital Out” to “PCM” from the on-screen
displays
54 59
. Otherwise, high volume sound may
damage your hearing as well as the speakers.
• When playing DTS-encoded discs (audio CDs),
excessive noise may be output from the analog audio
output jacks. To avoid possible damage to the audio
system, you should take proper precautions when the
analog audio output jacks of the DVD video player are
connected to an amplification system. To enjoy DTS
Digital Surround™ playback, an external 5.1 channel
DTS Digital Surround™ decoder system must be
connected to the OPTICAL or COAXIAL DIGITAL
AUDIO OUT jack of the DVD video player.
Notes
• DO NOT connect the OPTICAL or COAXIAL DIGITAL
AUDIO OUT jack of the DVD video player to the AC-3 RF
input of a Dolby Digital Receiver. This input on your A/V
Receiver is reserved for Laserdisc use only and is
incompatible with the OPTICAL / COAXIAL DIGITAL
AUDIO OUT jack of the DVD video player.
• Connect the COAXIAL DIGITAL AUDIO OUT jack of the
DVD video player to the “DIGITAL (COAXIAL)” input of a
Receiver or Processor.
• Connect the OPTICAL DIGITAL AUDIO OUT jack of the
DVD video player to the “DIGITAL (OPTICAL)” input of a
Receiver or Processor.
• Refer to the owner’s manual of the connected equipment
as well.
• When you connect the DVD video player to other
equipment, be sure to turn off the power and unplug all of
the equipment from the wall outlet before making any
connections.
• The output sound of the DVD video player has a wide
dynamic range. Be sure to adjust the receiver’s volume to
a moderate listening level. Otherwise, the speakers may
be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect
the DVD video player’s power cord. If you leave the
amplifier power on, the speakers may be damaged.
• For connection to yourTV, see “Connecting to aTV”
18 19
.
• For details of output sound, see
43
.
• This section uses the following reference marks.
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow

21
Connections
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic”and the
double-D symbol are trademarks of Dolby
Laboratories. Confidentialunpublished
works. Copyright 1992-1997 Dolby
Laboratories. All rights reserved.
• Use DVD video discs encoded via
the Dolby Digital recording
system.
• Make the following setting.
On-screendisplay Select: Page
“Raw”
or
‘PCM”
“Digital Out”
Recordingsystem D
Connecting to an amplifier equipped with a Dolby Digital decoder
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the
latest movies, and is now available to reproduce this realistic effect in the home.
You can enjoy motion picture and live concert DVD video discs with this dynamic
realistic sound by connecting the DVD video player to a 6 channel amplifier
equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a
Dolby Surround Pro Logic decoder, you will obtain the full benefit of Pro Logic
from the same DVD movies that provide full 5.1-channel Dolby Digital
soundtracks, as well as from titles with the Dolby Surround mark.
Connecting to an amplifier equipped with Dolby Surround Pro Logic
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by
connecting an amplifier and speaker system (right and left front speakers, a
center speaker, and one or two rear speakers).
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an
amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s
owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro
Logic sound.
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
* Connect one or two rear speakers.
The output sound from the rear speakers
will be monaural even if you connect two
rearspeakers.
Amplifier equipped with a
Dolby Digital decoder
75 Ωcoaxial cable
To COAXIAL
type digital
audioinput
Amplifier equipped with
Dolby Surround Pro Logic
To audio input
Audio cable
*
To ANALOG
AUDIO OUT
• Make the following setting.
On-screendisplay Select: Page
“Digital Out”
Connect
either.
“Raw”
or
“PCM”
43
To OPTICAL
type digital
audio input
Optical digital cable
54
59
54
59