Toshiba 27WL56P User manual

SERVICE MANUAL
LCD Color Television
27WL56P
FILE NO. 030-200503
Published in Japan, Apr. 2005 (YC)
TOSHIBA CORPORATION, 2005
All manuals and user guides at all-guides.com
all-guides.com

- 2 -
TABLE OF CONTENTS
SERVICE SAFETY PRECAUTIONS .................................................................................................................................... 3
HANDLING THE LCD MODULE .......................................................................................................................................... 5
SERVICE MODE .................................................................................................................................................................. 7
LOCATION OF CONTROLS ............................................................................................................................................... 12
LAYOUT OF MAJOR BOARDS .......................................................................................................................................... 14
MECHANICAL DISASSEMBLY .......................................................................................................................................... 15
EXPLODED VIEW .............................................................................................................................................................. 17
PACKING DISASSEMBLY ................................................................................................................................................. 19
CHASSIS AND CABINET REPLACEMENT PARTS LIST ................................................................................................. 20
PC BOARDS TOP & BOTTOM VIEW ................................................................................................................................ 26
CIRCUIT BLOCK DIAGRAM .............................................................................................................................................. 40
SPECIFICATIONS ............................................................................................................................................................. 41
APPENDIX:
SCHEMATIC DIAGRAM
All manuals and user guides at all-guides.com

- 3 -
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
SERVICE SAFETY PRECAUTIONS
• The caution items shown here describe major safety issues and should always be observed.
• The meanings of the various indications are as follows.
WARNING
CAUTION
Indicates a hypothetical situation in which service personnel and nearby third parties, or even
end users due to a product defect after the service operation is completed, could possibly be in
danger of injury or even death in the event of operational error.
Indicates a hypothetical situation in which service personnel and nearby third parties, or even
end users after the service operation is completed, could possibly be in danger of injury, or
where there could be physical damage in the event of operational error.
* Physical damage means major damage to a home, furnishings and other possessions.
Examples of marks
SHOCK HAZARD
PROHIBIT DISASSEM-
BLING
UNPULUG
The " indicates caution (including danger and warning).
The actual meaning of this caution is indicated inside the
" or nearby illustrations or text.
The example shown to the left indicates the danger of "electrical shock".
The indicates a forbidden action.
The actual meaning of this caution is indicated inside the or nearby illustrations or text.
The example shown to the left indicates that disassembly is forbidden.
The
- indicates a forced action (an action that must be performed).
The actual meaning of this forced action is indicated by
- or nearby illustrations or text.
The example shown to the left indicates that the power plug must be disconnected.
All manuals and user guides at all-guides.com

- 4 -
WARNING
KEEP CHILDREN
AWAY
UNPULUG
SHOCK HAZARD
USE SPECIFIED
PARTS
CAUTION FOR
WIRING
CAUTION FOR
ASSEMBLING /
WIRING
CHECK INSULATION
RESISTANCE
PROHIBIT
REMODELING
• Always advise users to keep children away.
There is danger of injury to children from tools, disassembled products, etc.
• Always disconnect the power plug before starting work whenever power is not required.
Failure to disconnect the power plug before starting work can result in electrical shock.
• Depending on the model, use an insulation transformer or wear gloves when servicing with the
power on, and disconnect the power plug to avoid electrical shock when replacing parts.
In some cases, alternating current is also impressed in the chassis, so electrical shock is pos-
sible if the chassis is contacted with the power on.
• Always use the replacement parts specified for the particular model when making repairs.
The parts used in products have the necessary safety characteristics such as inflammability,
voltage resistance, etc.; therefore, use only replacement parts that have these same character-
istics.
Use only the specified parts when the mark is included in a circuit diagram or parts list.
• Parts mounting and routing of the wiring should be the same as that used originally.
For safety purposes, insulating materials such as tubing or tape is sometimes used and printed
circuit boards are sometimes mounted floating.
Also make sure that wiring is routed and clamped to avoid parts that generate heat and which
use high voltage. Always follow the original scheme.
• After a repair has been completed, reassemble all disassembled parts, and route and recon-
nect the wiring, in accordance with the original scheme.
Do not allow internal wiring to be pinched by cabinets, panels, etc.
Any error in reassembly or wiring can result in electrical leakage, flame, etc., and may be
hazardous.
• After completing the work, disconnect the power plug from the outlet, remove the antenna, turn
on the power switch. Then, use a 500V insulation resistance meter to check the insulation
resistance of the antenna terminal, other metallic parts and between the prongs of the power
plug to make sure that the insulation resistance is 1M 1or more.
The set will require inspection and repair if the insulation resistance is below this value.
• Never remodel the product in any way.
Remodeling can result in improper operation, malfunction, or electrical leakage and flame,
which may be hazardous
All manuals and user guides at all-guides.com

- 5 -
GENERAL ADJUSTMENTSSPECIFIC INFORMATIONS
HANDLING THE LCD MODULE
Safety Precautions
In the event that the screen is damaged or the liquid crystal
(fluid) leaks, do not breathe in or drink this fluid. Also, never
touch this fluid.
Such actions could cause toxicity or skin irritation. If this fluid
should enter the mouth, rinse the mouth thoroughly with wa-
ter. If the fluid should contact the skin or clothing, wipe off
with alcohol, etc., and rinse thoroughly with water. If the fluid
should enter the eyes, immediately rinse the eyes thoroughly
with running water.
Precautions for Handling the LCD Module
The LCD module can easily be damaged during disassembly
or reassembly; therefore, always observe the following pre-
cautions when handling the module.
1. When attaching the LCD module to the LCD cover, posi-
tion it appropriately and fasten at the position where the
display can be viewed most conveniently.
2. Carefully align the holes at all four corners of the LCD
module with the corresponding holes in the LCD cover
and fasten with screws. Do not strongly push on the mod-
ule because any impact can adversely affect the perform-
ance. Also use caution when handling the polarized screen
because it can easily be damaged.
CAUTION The metal edges of the LCD module
are sharp, so use caution to avoid in-
jury.
3. If the panel surface becomes soiled, wipe with cotton or a
soft cloth. If this does not remove the soiling, breathe on
the surface and then wipe again.
If the panel surface is extremely solied, use a CRT cleaner
as a cleaner. Wipe off the panel surface by drop the cleaner
on the cloth. Do not drop the cleaner on the panel. Pay
attention not to scratch the panel surface.
4. Leaving water or other fluids on the panel screen for an
extended period of time can result in discoloration or
stripes. Immediately remove any type of fluid from the
screen.
5. Glass is used in the panel, so do not drop or strike with
hard objects. Such actions can damage the panel.
6. CMOS-LSI circuitry is used in the LCD module, so avoid
damage due to static electricity. When handling the mod-
ule, use a wrist ground or anchor ground.
All manuals and user guides at all-guides.com

- 6 -
7. Do not expose the LCD module to direct sunlight or strong
ultraviolet rays for an extended period of time.
8. Do not store the LCD module below the temperature con-
ditions described in the specifications. Failure to do so
could result in freezing of the liquid crystal due to cold air
or loss of resilience or other damage.
9. Do not disassemble the LCD module. Such actions could
result in improper operation.
10. When transporting the LCD module, do not use packing
containing epoxy resin (amine) or silicon resin (alcohol or
oxim). The gas generated by these materials can cause
loss of polarity.
All manuals and user guides at all-guides.com
all-guides.com

- 7 -
Test signal selection : abutton (on Remote)
Selection of the adjustment items : Channel s/t(on TV or Remote)
Change of the data value : Volume ;+/– (on TV or Remote)
Adjustment menu mode ON/OFF : MENU button (on TV)
Initialization of the memory : CALL + Channel button on TV (s)
Reset the count of operating protect
circuit to “00”: CALL + Channel button on TV (t)
“RCUT” selection : 1 button
“GCUT” selection : 2 button
“BCUT” selection : 3 button
“SCNT” selection : 4 button
“COLP” selection : 5 button
“TNTC” selection : 6 button
Color thickness correction
note: Displayed differently as shown below, de-
pending on the setting of the receiving color
system.
COLP (PAL)
COLC (NTSC)
COLS (SECAM)
Automatic A/D Adjustment(PC, Component) : 7 button
Self diagnostic display ON/OFF : 9 button
CAUTION : Never try to perform initialization unless you have changed the memory IC.
SERVICE MODE
1. ENTERING SERVICE MODE
1) Press button once on 2) Press button again and 3) While pressing the button,
Remote Control. keep pressing. press MENU button on TV set.
(Service mode display)
2. DISPLAYING THE ADJUSTMENT MENU
1) Press MENU button on TV.
Service mode Adjustment mode
3. KEY FUNCTION IN THE SERVICE MODE
The following key entry during display of adjustment menu provides special functions.
Press
Press
or Sound Mute
All manuals and user guides at all-guides.com

- 8 -
4. SELECTING THE ADJUSTING ITEMS
1) Every pressing of CHANNEL sbutton in the service mode changes the adjustment items in the order of table-2.
(tbutton for reverse order)
5. ADJUSTING THE DATA
1) Pressing of VOLUME ;+/– button will change the value of data in the range from 00H to FFH. The variable range
depends on the adjusting item.
6. EXIT FROM SERVICE MODE
1) Pressing POWER button to turn off the TV once.
■INITIALIZATION OF MEMORY DATA
After replacing EEPROM IC, the following initialization is required.
1. Enter the service mode, then select any register item.
2. Press and hold the CALL button on the Remote, then press the CHANNEL sbutton on the TV.The initialization of EEPROM IC
has been complated.
3. Check the picture carefully. If necessary, adjust any adjustment item above.
Perform “Auto tune” on the owner’s manual.
CAUTION: Never attempt to initialize the data unless EEPROM IC has been replaced.
7. TEST SIGNAL SELECTION
1) Every pressing of abutton on the Remote Control changes the built-in test patterns on screen as described below
in SERVICE MODE.
Signals Picture
• Red raster
• Green raster
• Blue raster
• All Black
• All White
R
All BlackAll White
BSignal off G
All manuals and user guides at all-guides.com

- 9 -
8. SELF DIAGNOSTIC FUNCTION
1) Press “9” button on Remote Control during display of adjustment menu in the service mode.
The diagnosis will begin to check if interface among IC’s is executed properly.
2) During diagnosis, the following displays are shown.
1Firmware :
Version information of microprocessor
In case of file name : WL56_EU and Version : 0100 indicates[WL56_EU_0100].
2Time : Total hour of turn the TV on. (Unit : H)
3Power :Operation number of protecting circuit ----"000" is normal.
When indication is other than "000", overcurrent apt to flow, and circuit parts may possibly be damaged.
4Bus line : --"OK" is normal
"SCL-GND"(Red indication) : SCL-GND short circuit
"SDA-GND"(Red indication) : SDA-GND short circuit
"SCL-SDA"(Red indication) : SCL-SDA short circuit
5Bus cont : --- "OK" is normal.
NG is abnormal(Red indication).
When type name of semiconductor indicates.
6Block
UV : TV reception mode
V1 : VIDEO 1 input mode ( 1)
V2 : VIDEO 2 input mode ( 2)
V3 : VIDEO 3 input mode ( 3)
V4 : VIDEO 4 input mode ( HDMI)
78 digit : CD number
8Model name (7 digit)
000
000000
27WL56P
27WL56P
WL56_EU_0100
WL56_EU_0100
1
2
3
4
5
6
78
All manuals and user guides at all-guides.com

- 10 -
9. VERSION CHECK MODE
1) Press “9” button twice on Remote Control during display of adjustment menu in the service mode. The version of main
MPU will begin to check.
2) During Version Check, the following displays are shown.
1MAIN MPU :
Version information of microprocessor
In case of file name : WL56_EU, Version 0100 for Code Program Version
and (E16) for OSD Version indicates [WL56_EU_0100(E16)]
2EEPROM :
Version information of EEPROM : Display 1 byte data.
3SUB MPU :
Version information of SUB MPU : Display 1 byte data.
4OPTION :
Option information : Display six numbers of 1 byte data.
5HDMI ID :
HDMI ID information : Display 4 byte data.
6CD number : Display 8 digit number
7Model name : Display 7 digit number
8LCD Panel Vender information display
The following Panel Vender and screen size are displayed.
WL56_EU_0100 (E16)
2E
27WL56P 27
1
2
3
4
5
6
78
Panel Vender Screen Size(Inch)
LPL -23
SHP -26
CMO -32
-37
-47
Example : SHP-32 indicates that Vender is SHP and Screen Size is 32 inch.
All manuals and user guides at all-guides.com

- 11 -
10. STATUS CHECK MODE
1) Press “9” button thrice on Remote Control during display of adjustment menu in the service mode. The status of this model
will begin to check.
2) During Status Check, the following displays are shown.
1MAIN :
Main source information :
Display RF position number (0 - 99) on the main screen, or Input Source (EXT1/2/3/HDMI etc.)
2MAIN FORMAT :
Display Video and PC format information
3MAIN PLL :
Main PLL information : Display 1 byte data at five.
4SCREEN SIZE :
Display the screen size as follows.
5OTHER STATUS :
Other status information : Display three numbers of 2 byte data.
Super live
Cinema
Subtitle
14:9
Wide
4:3
EXT1
1080i-50
C6 38 54 CE 08
0000 0000 0000
1
2
4
5
3
All manuals and user guides at all-guides.com
all-guides.com

- 12 -
LOCATION OF CONTROLS
Front
Back
Standby
RED – Power On
GREEN – On-timer set
HDMI
HDMI
media recorder
decoder*
CABLE HOLDER
FIXING STRAP
HDMI™ INPUT
SCART 2 (EXT2)
SCART 1 (EXT1)
IN/OUT
MEDIA REC.
TV
SAT
All manuals and user guides at all-guides.com

- 13 -
Remote control
To mute the sound
Text control buttons
To exit Menus
Bass Boost
Stereo/Bilingual reception
To bring up on-screen information and
for the text initial/index function
To select input from external sources
To access sub-pages when in text mode
To select mode
On-screen Menus
Selectable picture preferences Widescreen viewing
Number buttons
To return to the previous programme
For On/Standby mode
To display text services
When using a TOSHIBA VCR or DVD:
press
m
to PAUSE
press
w
to EJECT
press
l
q
to SKIP-REWIND
press
s
l
to SKIP-FORWARD
press
r
to PLAY
press
p
to STOP
press
q
to REWIND
press
s
to FAST FORWARD
To change programme positions and
text pages
To alter the volume
When using menus the arrows move the
cursor on the screen up, down, left or
right. OK to confirm your selection
When in TV mode:
8
/
9
Time display
When in Text mode:
r
To reveal concealed text
q
To hold a wanted page
s
To enlarge text display size
8
/
9
To select a page whilst viewing a
normal picture
All manuals and user guides at all-guides.com

- 14 -
LAYOUT OF MAJOR BOARDS
U004
AV OTHER BOARD
U003
SIGNAL BOARD
U006
KEY BOARD
U005
LED/RMT BOARD
U002
AC-IN BOARD
U007
PC-IN BOARD
U001
POWER BOARD
All manuals and user guides at all-guides.com

- 15 -
BITTB3×16 SBN ×10
PP3×8+SW+W ×4
PP5×16 SW+W SBN
×3
A450
A401
A445
A420
MECHANICAL DISASSEMBLY
1. Remove the stand (foot) and back cover.
2. Remove the boards (KEY, PC-IN) and piece key ass'y.
P801
A315
PP4×8+SW+W
×2
BITTB3×8 SBN
×2
PP3×8+SW+W
×2
PP4×8+SW+W
PP4×8+SW+W
PP4×8+SW+W×6
PP4×8+SW+W×2
4-40UNC
JFS-4S L=13
BITTB3×12
SBN ×2
U007
U006
A340
A320
All manuals and user guides at all-guides.com

- 16 -
W661
W661
BITTB4×16 SBN
×4
BITTB4×16 SBN ×4
H001
PP12
PP08
PP08
BITTB3×12 SBN
×2
PP3×8+SW+W
×6
PP3×8+SW+W
×4
PP3×8+SW+W
×5
PP3×8+SW+W
×5
U005 U003
U004
U002
U001
3. Remove the boards (POWER, AC-IN, SIGNAL, AV OTHER, LED/RMT) and speaker.
4. Remove the display.
PP08
B001
A201
PP4×12 +SW+W SBN
×4 BITTB4×16 SBN
×14
All manuals and user guides at all-guides.com
all-guides.com

- 17 -
EXPLODED VIEWS
1. Chassis Block
PP4×8+SW+W SBN
×2
BITTB3×12 SBN
×2
PP4×8+SW+W SBN
PP4×8+SW+W SBN
PP4×8+SW+W SBN
×6
4-40UNC
JFS-4S L=13
BITTB3×8 SBN
×2
PP4×8+SW+W
SBN ×2
BITTB3×16 S B N
×10
PP3×8+SW+W SBN
×4
A450
A445
A401
A420
PP5×16 SW+W SBN
×5
U007
U006
A340
A320
All manuals and user guides at all-guides.com

- 18 -
PP3×8+SW+W SBN
×4
PP3×8+SW+W SBN
×6
BITTB4×16 SBN
×4
BITTB4×16 SBN
×4
PP3×8+SW+W SBN
×5
PP3×8+SW+W SBN
×5
BITTB3×12 SBN
×2
PP4×12+SW+W SBN
×4
BITTB4×16 SBN
×14
PP08
PP12
H001
U003
U004
U001
U002
PP08
PP08
W661
W661
A201
B001
PP3×8+SW+W SBN
×2P801
A315
U005
2. Main Block
All manuals and user guides at all-guides.com

- 19 -
PACKING DISASSEMBLY
A702B
A702B
A702A
A702A
Y130Y170 Y101E
Y101
A701A
A703
All manuals and user guides at all-guides.com

- 20 -
Location Parts No. Description
No.
Location Parts No. Description
No.
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “SERVICE SAFETY PRECAUTIONS” ON PAGE 3 OF
THIS MANUAL.
CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate com-ponents
which have special characteristics important for safety and should be replaced only with types identical to those in
the original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals.
Before replacing any of these components, read carefully the SERVICE SAFETY PRECAUTIONS. Do not degrade
the safety of the receiver through improper servicing.
NOTICE:
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the
Model number and Description.
• The PC board assembly with ∗ mark is no longer available after the end of the production.
CHASSIS AND CABINET REPLACEMENT PARTS LIST
Model : 27WL56P
Capacitors ............. CD : Ceramic Disk PF : Plastic Film EL : Electrolytic
Resistors ............... CF : Carbon Film CC : Carbon Composition MF : Metal Film
OMF : Oxide Metal Film VR : Variable Resistor FR : Fusible Resistor
(All CD and PF capacitors are ±5%, 50V and all resistors, ±5%, 1/6W unless otherwise noted.)
CAPACITORS
C101 76109103 CERAMIC CHIP, 50V B 0.01UF K
C102 76073019 ELECTROLYTIC, 10V 470UF M 3A
C103 76109102 CERAMIC CHIP, 50V B 1000PF K
C104 76073084 ELECTROLYTIC, 50V 4.7UF M 3A
C105 76073019 ELECTROLYTIC, 10V 470UF M 3A
C162 76105101 CERAMIC CHIP, 50V CH 100PF J
C164 76100103 CERAMIC CHIP, 50V F 0.01UF Z
C190 76092730 CERAMIC CHIP, 16V B 0.1UF K
C501 76092730 CERAMIC CHIP, 16V B 0.1UF K
C502 76092730 CERAMIC CHIP, 16V B 0.1UF K
C503 76794470 ELECTROLYTIC, 16V 47UF M
C504 76109103 CERAMIC CHIP, 50V B 0.01UF K
C505 76794470 ELECTROLYTIC, 16V 47UF M
C506 76109103 CERAMIC CHIP, 50V B 0.01UF K
C514 76763221 ELECTROLYTIC, 16V 220UF M
C516 76105110 CERAMIC CHIP, 50V CH 11PF J
C517 76206478 ELECTROLYTIC, 50V 0.47UF M 7L 3A
C519 76797479 ELECTROLYTIC, 50V 4.7UF M
C521 76092733 CERAMIC CHIP, 50V B 0.022UF K
C524 76109103 CERAMIC CHIP, 50V B 0.01UF K
C526 76109103 CERAMIC CHIP, 50V B 0.01UF K
C527 76797229 ELECTROLYTIC, 50V 2.2UF M
C660 76669479 ELECTROLYTIC, 50V 4.7UF M
C661 76669479 ELECTROLYTIC, 50V 4.7UF M
C662 76109681 CERAMIC CHIP, 50V B 680PF K
C663 76109681 CERAMIC CHIP, 50V B 680PF K
C668 76766100 ELECTROLYTIC, 50V 10UF M
C670 76669100 ELECTROLYTIC, 50V 10UF M
C671 76669100 ELECTROLYTIC, 50V 10UF M
C673 76667470 ELECTROLYTIC, 25V 47UF M 3A
C674 76073081 ELECTROLYTIC, 50V 1UF M 3A
C675 76669339 ELECTROLYTIC, 50V 3.3UF M
C676 76765101 ELECTROLYTIC, 35V 100UF M
C678 76503041 PLASTIC FILM , 63V 0.1UF J
C679 76503041 PLASTIC FILM , 63V 0.1UF J
C680 76073072 ELECTROLYTIC, 35V 1000UF M 3A
C681 76073072 ELECTROLYTIC, 35V 1000UF M 3A
C682 76073072 ELECTROLYTIC, 35V 1000UF M 3A
C684 76109103 CERAMIC CHIP, 50V B 0.01UF K
C685 76109103 CERAMIC CHIP, 50V B 0.01UF K
C688 76109103 CERAMIC CHIP, 50V B 0.01UF K
C694 76109103 CERAMIC CHIP, 50V B 0.01UF K
C699 76206478 ELECTROLYTIC, 50V 0.47UF M 7L 3A
C699B 23960136 ADHESIVE, SILICONE, TSE3843-W
C801 76503507 PLASTIC FILM, AC275V 0.22UF K
C802 76503507 PLASTIC FILM, AC275V 0.22UF K
C803 24503437 PLASTIC FILM CQ92 T 630V 0.15UF J
C804 76214103 CERAMIC DISC, 500V B 0.01UF K
C805 76092281 CERAMIC DISC, AC250V E 4700PF
C810 76125008 ELECTROLYTIC CE692R 450V 220UF M
C811 76092567 CERAMIC DISC, AC250V E 1000PF M
C812 76092567 CERAMIC DISC, AC250V E 1000PF M
C813 76503047 PLASTIC FILM, 63V 0.33UF J
C815 76503049 PLASTIC FILM, 63V 0.47UF J
C816 76073090 ELECTROLYTIC, 50V 100UF M 3A
C817 76567224 PLASTIC FILM, 50V 0.22UF J
C819 76214101 CERAMIC DISC, 500V B 100PF K
C820 76567224 PLASTIC FILM, 50V 0.22UF J
C821 76092343 CERAMIC DISC, 2KV 680PF K
C822 76092344 CERAMIC DISC, 2KV 820PF K
C823 76092341 CERAMIC DISC, 2KV R 470PF K
C824 76591102 PLASTIC FILM, 50V 1000PF J
C825 76503053 PLASTIC FILM, 63V 1UF J
C826 76092341 CERAMIC DISC, 2KV R 470PF K
C827 76678229 ELECTROLYTIC, 200V 2.2UF M 3A
C851 76092538 CERAMIC CHIP, 10V F 1UF Z
C852 76109102 CERAMIC CHIP, 50V B 1000PF K
C883 76073193 ELECTROLYTIC, 35V 2200UF M 3A
C884 76073193 ELECTROLYTIC, 35V 2200UF M 3A
C889 76073094 ELECTROLYTIC, 50V 1000UF M 3A
C890 76503047 PLASTIC FILM, 63V 0.33UF J
C6600 76797470 ELECTROLYTIC, 50V 47UF M
C6601 76085944 ELECTROLYTIC, NP, 50V 2.2UF M 11L
C6602 76085944 ELECTROLYTIC, NP, 50V 2.2UF M 11L
C6603 76766229 ELECTROLYTIC, 50V 2.2UF M
C6604 76766229 ELECTROLYTIC, 50V 2.2UF M
C6605 76766100 ELECTROLYTIC, 50V 10UF M
C8001 76073072 ELECTROLYTIC, 35V 1000UF M 3A
C8110 76125008 ELECTROLYTIC CE692R 450V 220UF M
CB01 76202221 ELECTROLYTIC, 10V 220UF M 7L 3A
CB02 76202221 ELECTROLYTIC, 10V 220UF M 7L 3A
CB03 76100104 CERAMIC CHIP, 25V F 0.1UF Z
CB04 76100104 CERAMIC CHIP, 25V F 0.1UF Z
CB05 76202221 ELECTROLYTIC, 10V 220UF M 7L 3A
CB38 76100104 CERAMIC CHIP, 25V F 0.1UF Z
CC01 76109102 CERAMIC CHIP, 50V B 1000PF K
CC02 76109102 CERAMIC CHIP, 50V B 1000PF K
All manuals and user guides at all-guides.com