Toshiba 32W301Ps User manual

(*1) GREEN PRODUCT PROCUREMENT
The EC is actively promoting the WEEE & RoHS Directives that define standards for recycling
and reuse of Waste Electrical and Electronic Equipment and for the Restriction of the use of
certain Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any
marketing of new products containing the restricted substances.
Increasing attention is given to issues related to the global environmental. Toshiba Corporation
recognizes environmental protection as a key management tasks, and is doing its utmost to
enhance and improve the quality and scope of its environmental activities. In line with this,
Toshiba proactively promotes Green Procurement, and seeks to purchase and use products,
parts and materials that have low environmental impacts.
Green procurement of parts is not only confined to manufacture. The same green parts used in
manufacture must also be used as replacement parts.
(*2) LEAD-FREE SOLDER
This product is manufactured using lead-free solder as a part of a movement within the consumer
products industry at large to be environmentally responsible. Lead-free solder must be used in
the servicing and repair of this product.
WARNING
This product is manufactured using lead free solder.
DO NOT USE LEAD BASED SOLDER TO REPAIR THIS PRODUCT !
The melting temperature of lead-free solder is higher than that of leaded solder by 86°F to 104°F
(30°C to 40°C). Use of a soldering iron designed for lead-based solders to repair product made
with lead-free solder may result in damage to the component and or PCB being soldered. Great
care should be made to ensure high-quality soldering when servicing this product especially
when soldering large components, through-hole pins, and on PCBs as the level of heat
required to melt lead-free solder is high.
A1-1

SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES
As for the places which need special attentions,
they are indicated with the labels or seals on the
cabinet, chassis and parts. Make sure to keep the
indications and notices in the operation manual.
3. USE THE DESIGNATED PARTS
5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
HOW TO ORDER PARTS
When you exchange IC and Transistor with a heat sink, apply silicon grease on the contact section of
the heat sink. Befor applying new silicon grease, remove all the old silicon grease.
(Old grease may cause damages to the IC and Transistor.)
IMPORTANT
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an
electric shock while the electric current is
flowing.
The parts in this equipment have the specific
characters of incombustibility and withstand
voltage for safety. Therefore, the part which is
replaced should be used the part which has
the same character.
Especially as to the important parts for safety
which is indicated in the circuit diagram or the
table of parts as a mark, the designated
parts must be used.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING
There are parts which use the insulation
material such as a tube or tape for safety, or
which are assembled in the condition that
these do not contact with the printed board.
The inside wiring is designed not to get closer
to the pyrogenic parts and high voltage parts.
Therefore, put these parts in the original
positions.
In the condition that an explosion-proof cathode-
ray tube is set in this equipment, safety is
secured against implosion. However, when
removing it or serving from backward, it is
dangerous to give a shock. Take enough care to
deal with it.
PERFORM A SAFETY CHECK AFTER
SERVICING
6.
Confirm that the screws, parts and wiring which
were removed in order to service are put in the
original positions, or whether there are the
portions which are deteriorated around the
serviced places serviced or not. Check the
insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
1.
2.
3.
4.
Unplug the plug from the AC outlet.
Remove the antenna terminal on TV and turn
on the TV.
Insulation resistance between the cord plug
terminals and the eternal exposure metal
[Note 2] should be more than 1M ohm by
using the 500V insulation resistance meter
[Note 1].
If the insulation resistance is less than 1M
ohm, the inspection repair should be
required.
[Note 1]
If you have not the 500V insulation
resistance meter, use a Tester.
[Note 2]
External exposure metal:
A1-2
Antenna terminal
Headphone jack

TABLE OF CONTENTS
GREEN PRODUCT PROCUREMENT ........................................................................................
LEAD-FREE SOLDER ................................................................................................................
SERVICING NOTICES ON CHECKING.....................................................................................
HOW TO ORDER PARTS ..........................................................................................................
IMPORTANT ...............................................................................................................................
TABLE OF CONTENTS..............................................................................................................
GENERAL SPECIFICATIONS ...................................................................................................
DISASSEMBLY INSTRUCTIONS ............................................................................................
SERVICE MODE LIST ................................................................................................................
WHEN REPLACING EEPROM (MEMORY) IC ..........................................................................
ELECTRICAL ADJUSTMENTS..................................................................................................
BLOCK DIAGRAMS
MAIN ........................................................................................................................................
POWER ...................................................................................................................................
PRINTED CIRCUIT BOARDS
MAIN ........................................................................................................................................
POWER/OPERATION/REMOCON .........................................................................................
SCHEMATIC DIAGRAMS
21 PIN ......................................................................................................................................
POWER 3 ................................................................................................................................
REGULATOR...........................................................................................................................
AV JACK/SWITCH...................................................................................................................
SOUND AMP/HEADPHONE AMP ..........................................................................................
TUNER.....................................................................................................................................
SCALER...................................................................................................................................
SUB MICON/RS-232C ............................................................................................................
JACK ........................................................................................................................................
PANEL INTERFACE................................................................................................................
INTERFACE_HDMI IC ............................................................................................................
POWER 1 ................................................................................................................................
POWER 2 ................................................................................................................................
OPERATION/REMOCON ........................................................................................................
INTERCONNECTION..................................................................................................................
WAVEFORMS .............................................................................................................................
MECHANICAL EXPLODED VIEWS...........................................................................................
MECHANICAL REPLACEMENT PARTS LIST .........................................................................
ELECTRICAL REPLACEMENT PARTS LIST...........................................................................
A1-1
A1-1
A1-2
A1-2
A1-2
A2-1
A3-1~A3-5
B-1, B-2
C-1
C-2
D-1~D-7
E-1, E-2
E-3, E-4
F-1~F-4
F-5~F-8
G-1, G-2
G-3, G-4
G-5, G-6
G-7, G-8
G-9, G-10
G-11, G-12
G-13, G-14
G-15, G-16
G-17, G-18
G-19, G-20
G-21, G-22
G-23, G-24
G-25, G-26
G-27, G-28
G-29, G-30
H-1, H-2
I-1~I-3
J1-1, J1-2
J2-1~J2-17
A2-1

GENERAL SPECIFICATIONS
G-1 TV LCD LCD Size / Visual Size 31.51 inch / 800.4mmV
System LCD Type Color TFT LCD
Number of Pixels 1366(H) x 768(V)
View Range Left/Right 89/89 degree
Up/Down 89/89 degree
Color System PAL / SECAM
Speaker 2 Speaker
Position Front
Size 2.2 x 5.0 inch
Impedance 4 ohm
Sound Output MAX 10W + 10W
10%(Typical) ---
NTSC3.58+4.43 /PAL60Hz Yes
G-2 Tuning Broadcasting System
System Tuner and System 1Tuner
Receive CH Destination UK, I.R., CCIR Hyper+France CATV
CH Coverage IreE2~E4, X~Z+2, S1~S10, E5~E12,S11~S41,E21~E69
Intermediate
Frequency Picture(FP) 38.9 / 38.9 / 38.9 / 33.9MHz
Sound(FS) 33.4 / 32.9 / 32.4 / 40.4MHz
FP-FS 5.5 / 6.0 / 6.5 / 6.5MHz
Auto Tuning Method ALL Band (Not C.C.I.R. CH Plan)
Preset CH 99
Stereo/Dual TV Sound Nicam/A2 Dual
Tuner Sound Muting Yes
G-3 Power Power Source AC 220-240V AC 50Hz/60Hz
DC ---
Power Consumption at AC 150 W at AC 230 V 50 Hz
at DC --
Stand by (at AC) 1 W at 230V 50Hz
Per Year -- kWh/Year
Protector Power Fuse Yes
G-4 Regulation Safety CE(EN60065:2002)
Radiation CE
X-Radiation ---
G-5 Temperature Operation +
5
o
C
~ +4
0
o
C
Storage -2
0
o
C
~ +
60
o
C
G-6 Operating Humidity Less than 80% RH
G-7 OSD Language English, Spanish, German, French, Italian,
Swedish, Dutch, Russian, Portuguese,
Turkish, Greek, Finnish, Polish
G-8 Clock and Sleep Timer Max Time 120 Min
Timer Step 10 Min
On/Off Timer Program(On Timer / Off Timer) -- Program
Wake Up Timer No
Timer Back-up (at Power Off Mode) more than -- Min Sec
U.K., I.R., CCIR, FRENCH System
B/G, D/K, I/I, L
BG / II / DK, L / L' (SECAM VL)
A3-1

GENERAL SPECIFICATIONS
G-9 Remote Unit RC-NZ
Control Glow in Dark Remocon Yes
Remocon Format TOSHIBA
Format NEC
Custom Code 40-BF h
Power Source Voltage(D.C) 3V
UM size x pcs UM-3 x 2 pcs
Total Keys 33 Keys
Keys Power (Stand By) Yes
Display / (Status) Yes
Input Select Yes
Picture Size Yes
1 Yes
2 Yes
3 Yes
4 Yes
5 Yes
6 Yes
7 Yes
8 Yes
9 Yes
0 Yes
Sleep Yes
Mute Yes
Volume Up / Right Yes
Volume Down / Left Yes
CH Down No
CH Up No
Menu Yes
Up No
Down No
Left No
Right No
Enter Yes
Exit Yes
Freeze frame No
T'TEXT Keys TEXT / TAP / TV Yes
Reveal / Skip No
Reveal Yes
Display Cancel No
HOLD / Freeze Yes
Red Yes
Green Yes
Yellow Yes
Cyan Yes
Normal No
F/T/B(Expand) Yes
F/T/B(Expand) / Normal No
Quick View No
Sub Page / Quick View Yes
Up/CH Up No
Up / CH Up / Page Up Yes
Down / CH Down No
Down / CH Down / Page Down Yes
Reset No
Audio 1/2 Yes
Reset / Audio 1/2 No
A3-2

GENERAL SPECIFICATIONS
G-10 Features Power On Memory Yes
Auto Shut Off Yes
Just Clock Function No
Game Position No
DNR Yes
3D
Comb Filter Yes
3D
Auto Set Up (Fast installation) Auto tuning (Analog tuner) Yes
CH sort Yes
ATS Yes
Auto clock (Analog tuner) No
Plug in start Yes
Picture Setting(TV) Picture Preference Yes
Brightness , Contrast , Color Yes
Tint Yes
Sharpness Yes
DNR Yes
Color Temperature Yes
Blue Back Yes
Backlight Control Yes
Film Mode No
Picture Setting(PC) BRIGHTNESS , CONTRAST Yes
HOR POSITION , VER POSITION Yes
PHASE , CLOCK Yes
AUTO ADJUST No
RED , GREEN , BLUE Yes
Backlight Yes
WXGA INPUT Yes
WVGA INPUT No
Audio Nicam Yes
Tone Control (Bass/Treble/Balance) Yes
Surround Yes
BBE No
SRS WOW (SRS 3D/Focus/Tru Bass) No
Variable Audio Out Yes
Tuning Auto Tuning Yes
Manual Tuning Yes
CH Allocation Yes
Lock (Analog) Panel Lock No
Channel Lock No
Hotel Lock No
Screen Saver Inversion No
Full White No
Screen Saver No
Static Image No
Black Side Panel No
CH Label Yes
T'Text Yes
Text type Fastext / Toptext
Text Language English , French, Swedish, Hungarian
Turkish, German, Portuguese, Spanish,
Italian, Greek, Slovakian, Russian, Polish,
Czech, Rumanian, Estonian, Lettish,
Lithuanian, Ukrainian, Croatian, Slovenian,
Latvian
Wide Mode (AUTO/4:3/FULL SCREEN/16:9/CINEMA/14:9) Yes
HD Zoom No
Picture Scroll (Vertical Position) Yes
PFC(Power Factor circuit) Yes
Freeze frame Yes (w/o720p, 1080i)
HD-Ready Yes
Plug and Play No
Reset TV Setting Yes
Scart Spec Scart1 AV in Yes
AV out Yes (Tuner)
S-Video in Yes
RGB in Yes
Scart2 AV in Yes
AV out Yes (Monitor)
S-Video in Yes
RGB in Yes
A3-3

GENERAL SPECIFICATIONS
PC Monitor Input Yes
VGA (640x480) Yes (60Hz)
VGA (720x400) Yes (70Hz)
WVGA (848x480) No
SVGA (800x600) Yes (60Hz)
XGA (1024x768) Yes (60Hz)
WXGA (1280x768) Yes (60Hz)
WXGA (1280x720) Yes (60Hz)
WXGA (1360x768) Yes (60Hz)
SXGA (1280x1024) No
HDMI Input Yes (Ver. 1.2)
VGA (640x480) Yes (60Hz)
720x480i (4:3) Yes (60Hz)
720x480i (16:9) Yes (60Hz)
720x480p (4:3) Yes (60Hz)
720x480p (16:9) Yes (60Hz)
720x576i (4:3) Yes (50Hz)
720x576i (16:9) Yes (50Hz)
720x576p (4:3) Yes (50Hz)
720x576p (16:9) Yes (50Hz)
1280x720p Yes (50/60Hz)
1920x1080i Yes (50/60Hz)
Component Input Yes
720x480i (4:3) Yes (60Hz)
720x480i (16:9) Yes (60Hz)
720x480p (4:3) Yes (60Hz)
720x480p (16:9) Yes (60Hz)
720x576i (4:3) Yes (50Hz)
720x576i (16:9) Yes (50Hz)
720x576p (4:3) Yes (50Hz)
720x576p (16:9) Yes (50Hz)
1280x720p Yes (50/60Hz)
1920x1080i Yes (50/60Hz)
G-11 Accessories Owner's Manual Language English/French/Italy/Spanish/German/
Polish/Turkish/Greek/Dutch
w/Guarantee Card No
Remote Control Unit Yes
Rod Antenna No
Poles -
Terminal -
Loop Antenna (W/ Antenna Change Plug) No
Terminal -
U/V Mixer No
DC Car Cord (Center+) No
Guarantee Card No
Warning Sheet No
Circuit Diagram No
Antenna Change Plug No
Service Facility List No
Important Safeguard No
Quick Set-up Sheet No
Battery Yes
UM size x pcs UM-3 x 2 pcs
OEM Brand No
AC Adapter No
AC Cord (for AC Adapter) No
AC Cord Yes
AV Cord (2Pin-1Pin) No
HDMI-DVI Cable No
Registration Card No
300 ohm to 75 ohm Antenna Adapter No
A3-4

GENERAL SPECIFICATIONS
G-12 Interface Switch Power (Tact) Yes
System Select No
Main Power SW No
Channel Up/Menu Up Yes
Channel Down/Menu Down Yes
Volume Up/Menu > Yes
Volume Down/Menu < Yes
Input Select/Enter Yes
Menu Yes
Indicator Power/Stand-by Yes(GREEN / RED)
On Timer No
Terminals Side Video Input 1 RCA x 1
Audio Input 1 RCA x 2(L/MONO, R)
S- Input 1 Yes
Video Input 2 No
Audio Input 2 No
S- Input 2 No
Video Output No
Audio Output RCA x 2(Variable) (L, R)
Other Terminal No
Euro Scart (21Pin) 2Scart
Component In Yes
Audio Input (Component In use) RCA x 2(L/MONO, R)
PC Monitor Input (D-Sub) Yes
Audio Input Mini Pin Jack
(
o3.5
),
STEREO
HDMI Input 1 Yes
Audio Input (HDMI/DVI In use) PC Monitor Audio Input Alternative
HDMI Input 2 Yes
Audio Input (HDMI/DVI In use) Mini Pin Jack
(
o3.5
),
STEREO
Sub Woofer Output No
Diversity No
Ext Speaker No
DC Jack 12V(Center +) No
VHF/UHF Antenna Input DIN Type
AC Inlet Yes
Other Terminal Headphone
G-13 Set Size Approx. W x D x H (mm) 822 x 332.5 x 604
w/o Stand,Handle Approx. W x D x H (mm) 822 x 129 x 556.5
G-14 Weight Net Approx. 18.5kg (40.8 lbs)
Net w/o Stand,Handle Approx. 16.0kg (35.3 lbs)
Gross Approx. 22.5kg (49.6 lbs)
G-15 Carton Master Carton 3
Content ---- Sets
Material -- /--
Dimensions W x D x H(mm) -- x -- x --
Description of Origin No
Gift Box Yes
Material Double/Brown
Dimensions W x D x H(mm) 917 x 441 x 720
Design As per Buyer's
Description of Origin Yes
Drop Test Natural Dropping At 2 Corner / 2 Edges / 1 Surfaces
Height (cm) 50
Container Stuffing 201 Sets/40' container
G-16 Material Cabinet Cabinet Front PS 94V0 NON-DECABROM
Cabinet Rear PS 94V0 NON-DECABROM
PCB Non-Halogen No
Eyelet Yes
G-17 Environment Environmental standard requirement Green procurement of TOSHIBA
Pb- Free Phase3(PHASE3A)
Measures for Whisker Yes
WEEE Yes
A3-5

B-1
Masking Tape
(Cotton Tape)
DISASSEMBLY INSTRUCTIONS
1.
REMOVAL
IC
Put Masking Tape (cotton tape) around the Flat Pack-
age IC to protect other parts from any damage.
(Refer to Fig. 1-1.)
1.
Fig. 1-1
NOTE
REMOVAL AND INSTALLATION OF
FLAT PACKAGE IC
Some ICs on the PCB are affixed with glue, so be
careful not to break or damage the foil of each IC
leads or solder lands under the IC when removing it.
NOTE
Masking is carried out on all the parts located within
10 mm distance from IC leads.
Blower type IC
desoldering machine
IC
Heat the IC leads using a blower type IC desoldering
machine. (Refer to Fig. 1-2.)
2.
Fig. 1-2
NOTE
Do not rotate or move the IC back and forth until IC
can move back and forth easily after desoldering the
leads completely.
When IC starts moving back and forth easily after
desoldering completely, pickup the corner of the IC using
a tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 1-3.)
3.
Blower type IC
desoldering
machine
IC Fig. 1-3
Tweezers
Peel off the Masking Tape.4.
Absorb the solder left on the pattern using the Braided
Shield Wire. (Refer to Fig. 1-4.)
5.
NOTE
Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.
Braided Shield Wire
Soldering Iron
Fig. 1-4
IC pattern

B-2
DISASSEMBLY INSTRUCTIONS
Supply soldering
from upper position
to lower position
IC
Supply the solder from the upper position of IC leads
sliding to the lower position of the IC leads.
(Refer to Fig. 1-6.)
2.
Fig. 1-6
Soldering IronSolder
IC
Absorb the solder left on the lead using the Braided
Shield Wire. (Refer to Fig. 1-7.)
3.
Fig. 1-7
Soldering Iron
Braided Shield Wire
NOTE
Do not absorb the solder to excess.
IC
When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thin-
tip Soldering Iron. (Refer to Fig. 1-8.)
4.
Fig. 1-8
Thin-tip Soldering Iron
NOTE
When the IC leads are bent during soldering and/or
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, be always sure to replace the IC in this
case.
Finally, confirm the soldering status on four sides of the
IC using a magnifying glass.
Confirm that no abnormality is found on the soldering
position and installation position of the parts around the
IC. If some abnormality is found, correct by resoldering.
5.
Solder temporarily
Soldering Iron
INSTALLATION
Take care of the polarity of new IC and then install the
new IC fitting on the printed circuit pattern. Then solder
each lead on the diagonal positions of IC temporarily.
(Refer to Fig. 1-5.)
1.
Fig. 1-5
Solder temporarily

C-1
SERVICE MODE LIST
This unit is provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote
control for more than the standard time in the appropriate condition. (See below chart.)
Initialization of factory TV data.
NOTE: If you set factory initialization, the memories are reset
such as the channel setting, and the POWER ON total
hours.
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".
Set Key Operations
Remocon
Key
VOL. DOWN
(Minimum) 1 2 sec.
Standard
Time
VOL. DOWN
(Minimum) 6 2 sec.
VOL. DOWN
(Minimum) 9 2 sec.
Set
Condition
ALL mode
POWER ON
Display of the Adjustment MENU on the screen.
Refer to the "ELECTRICAL ADJUSTMENT"
(On-Screen Display Adjustment).
VOL. DOWN
(Minimum) 2
ALL mode Check of the SUM DATA, POWER ON total hours and MICON
VERSION on the screen.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".
2 sec.
POWER ON

C-2
CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION.
Initial total of MEMORY IC, POWER ON total hours and MICON VERSION can be checked on the screen. Total hours are
displayed in 16 system of notation.
NOTE:
1.
2.
3.
4.
Turn on the POWER, and set to the TV mode.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (2) on the remote control for more than 2 seconds.
After the confirmation of each check sum, POWER ON total hours and MICON VERSION , turn off the power.
WHEN REPLACING EEPROM (MEMORY) IC
If you set a factory initialization, the total hours is reset to "0".
Please refer to "CONFIRMATION OF INITIAL DATA" when SUM DATA is not corresponding.
4.
5.
6.
7.
8.
9.
10.
11.
12.
The unit will now have the correct DATA for the new MEMORY IC.
ADDRESS is now selected and should "blink". Using the UP/DOWN buton on the remote, step through
the ADDRESS until required ADDRESS to be changed is reached.
Press VOL. UP/DOWN button to select DATA. When DATA is selected, it will "blink".
Again, step through the DATA using UP/DOWN button until required DATA value has been selected.
Pressing LEFT/RIGHT button will take you back to ADDRESS for further selection if necessary.
Repeat steps 4 to 6 until all data has been checked.
When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
Turn POWER on.
Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds.
After the finishing of the initializing of shipping, the unit will turn off automatically.
FIG. 2
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to INITIAL SETTING TABLE (Attached "INITIAL DATA").
1.
2.
3.
Turn on the POWER, and set to the TV mode.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.
ADDRESS and DATA should appear as FIG 2.
CONFIRMATION OF INITIAL DATA
ADDRESS DATA
INIT 0000 00
ANALOG M : DB070_70509A
NOTE:The each item value might be different according to each set.
INIT : 5BE3
VCT-P : B8AD
LCD ON : 0000
ANALOG M : DB070_70509A
FIG. 1
Initial setting data check sum.
SCALER data check sum.
Main Micon check sum.
POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
+ (ones digit value)

ELECTRICAL ADJUSTMENTS
D-1
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
CAUTION
On-Screen Display Adjustment
1.
2. Set the VOLUME to minimum. Press the VOL. DOWN button on the set and the
channel button (9) on the remote control for more than
2 seconds to display adjustment mode on the screen as
shown in Fig. 2-1.
Fig. 2-1
3.
4.
5.
6.
Use the UP/DOWN button or Channel button (0-9) on
the remote control to select the options shown in
Fig. 2-2.
Press the ANALOG MENU button on the remote control
to end the adjustments.
To display the adjustment screen for TUNER, AV,
COMPONENT, HDMI and PC mode, press the INPUT
SELECT button on the remote control to set to the
TUNER, AV, HDMI and PC mode.
Press the VOL.DOWN button on the set and the
channel (9) on the remote control for more than 2
seconds.
FUNCTION
OSD H POSI
OSD V POSI
R DRIVE (N)
R CUT OFF (N)
G DRIVE (N)
G CUT OFF (N)
B DRIVE (N)
B CUT OFF (N)
R DRIVE (C)
R CUT OFF (C)
G DRIVE (C)
G CUT OFF (C)
B DRIVE (C)
B CUT OFF (C)
R DRIVE (W)
R CUT OFF (W)
G DRIVE (W)
G CUT OFF (W)
B DRIVE (W)
B CUT OFF (W)
H POSI
H POSI MAX
NO.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
•
•
•
Use an isolation transformer when performing any
service on this chassis.
When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
When you exchange IC and Transistor with a heat sink,
apply silicon grease on the contact section of the heat
sink. Before applying new silicon grease, remove all the
old silicon grease. (Old grease may cause damage to the
IC and Transistor).
2. BASIC ADJUSTMENTS
NO.
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
FUNCTION
H POSI MIN
V POSI
V POSI MAX
V POSI MIN
BACKLIGHT CENTER
BACKLIGHT MAX
BACKLIGHT MIN
BRIGHT CENTER
BRIGHT MAX
BRIGHT MIN
TINT CENTER
CONTRAST CENTER
CONTRAST MAX
CONTRAST MIN
CONTRAST 40
COLOR CENTER
COLOR MAX
COLOR MIN
TEXT H POIS
TEXT V POIS
FLICKER ADJ
Prepare the following measurement tools for electrical
adjustments.
1. Pattern Generator
Fig. 2-2
TUNER
01 OSD H POSI
16:9
21
2-1: WHITE BALANCE
1.
2.
3.
4.
5.
6.
7.
8.
Place the set in Aging Test for more than 15 minutes.
Receive the gray scale pattern from the Pattern
Generator.
Press the INPUT SELECT button on the remote control
to set to the AV mode.
Using the remote control, set the brightness and contrast
to normal position.
Activate the adjustment mode display of Fig. 2-1 and
press the channel button (03) on the remote control to
select "R DRIVE (N)".
Press the CH. UP/DOWN button on the remote control to
select the "R CUT OFF(N)", "G DRIVE(N)", "G CUT
OFF(N)", "B DRIVE(N)", "B CUT OFF(N)", "R DRIVE(C)",
"R CUT OFF(C)", "G DRIVE(C)", "G CUT OFF(C)", "B
DRIVE(C)", "B CUT OFF(C)", "R DRIVE(W)", "R CUT
OFF(W)", "G DRIVE(W)", "G CUT OFF(W)", "B
DRIVE(W)" or "B CUT OFF(W)".
Adjust the VOL. UP/DOWN button on the remote control
to whiten the R CUT OFF(N), G DRIVE(N), G CUT
OFF(N), B DRIVE(N), B CUT OFF(N), R DRIVE(C), R
CUT OFF(C)", G DRIVE(C), G CUT OFF(C), B
DRIVE(C), B CUT OFF(C), R DRIVE(W), R CUT
OFF(W), G DRIVE(W), G CUT OFF(W), B DRIVE(W)
and B CUT OFF(W) at each step tone sections equally.
Perform the above adjustments 6 and 7 until the white
color is achieved.
PAL

ELECTRICAL ADJUSTMENTS
D-2
2-2: CONTRAST MAX
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
Receive the monoscope pattern. (RF Input)
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 2-1 and
press the channel button (35) on the remote control to
select "CONTRAST MAX".
Press the LEFT/RIGHT button on the remote control
until the contrast step No. becomes "53"
Check if the picture is normal.
Receive the monoscope pattern. (VIDEO Input)
Press the INPUT SELECT button on the remote
control to set to the AV mode.
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 2-1 and
press the channel button (35) on the remote control to
select "CONTRAST MAX".
Press the LEFT/RIGHT button on the remote control
until the contrast step No. becomes "53".
Check if the picture is normal.
Playback the DVD(480i) disc. (COMPONENT Input)
Press the INPUT SELECT button on the remote
control to set to the COMPONENT mode.
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 2-1 and
press the channel button (35) on the remote control to
select "CONTRAST MAX".
Press the LEFT/RIGHT button on the remote control
until the contrast step No. becomes "56".
Playback the DVD(480i) disc. (HDMI Input)
Press the INPUT SELECT button on the remote
control to set to the HDMI mode.
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 2-1 and
press the channel button (35) on the remote control to
select "CONTRAST MAX".
Press the LEFT/RIGHT button on the remote control
until the contrast step No. becomes "56".
Check if the picture is normal.

2-3: Confirmation of Fixed Value (Step No.)
Please check if the fixed values of each of the adjustment item is set correctly referring below. (TUNER/AV/CS/HDMI/PC)
NO. FUNCTION CVBS S(Y/C) RGB 480i 480p 720p 1080i 576i 576p 720p 1080i 480i 480p VGA 720p 1080i 576i 576p 720p 1080i 640x480 720x400 800x600 1024x768 1280x720 1280x768 1360x768
Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No.
1 OSD H POSI 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21
2 OSD V POSI 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00000 0 0
3 R DRIVE(N) 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736
4 R CUT OFF(N) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ----- - -
5 G DRIVE(N) *714 *714 *714 *714 *714 *714 *714 *714 *714 *714 *714 *714 *714 *714 *714 *714 *714 *714 *714 *714 *714 714 714 714 714 714 714 714
6 G CUT OFF(N) *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 ----- - -
7 B DRIVE(N) *635 *635 *635 *635 *635 *635 *635 *635 *635 *635 *635 *635 *635 *635 *635 *635 *635 *635 *635 *635 *635 635 635 635 635 635 635 635
8 B CUTOFF(N) *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 *-2 ----- - -
9 R DRIVE(C) 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 ----- - -
10 R CUT OFF(C) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ----- - -
11 G DRIVE(C) *712 *712 *712 *712 *712 *712 *712 *712 *712 *712 *712 *712 *712 *712 *712 *712 *712 *712 *712 *712 *712 ----- - -
12 G CUT OFF(C) *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 *-5 ----- - -
13 B DRIVE(C) *654 *654 *654 *654 *654 *654 *654 *654 *654 *654 *654 *654 *654 *654 *654 *654 *654 *654 *654 *654 *654 ----- - -
14 B CUTOFF(C) *-3 *-3 *-3 *-3 *-3 *-3 *-3 *-3 *-3 *-3 *-3 *-3 *-3 *-3 *-3 *-3 *-3 *-3 -3 -3 -3 ----- - -
15 R DRIVE(W) 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 736 ----- - -
16 R CUT OFF(W) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ----- - -
17 G DRIVE(W) *692 *692 *692 *692 *692 *692 *692 *692 *692 *692 *692 *692 *692 *692 *692 *692 *692 *692 *692 *692 *692 ----- - -
18 G CUT OFF(W) *0 *0 *0 *0 *0 *0 *0 *0 *0 *0 *0 *0 *0 *0 *0 *0 *0 *0 *0 *0 *0 ----- - -
19 B DRIVE(W) *599 *599 *599 *599 *599 *599 *599 *599 *599 *599 *599 *599 *599 *599 *599 *599 *599 *599 *599 *599 *599 ----- - -
20 B CUTOFF(W) *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 *-4 ----- - -
H POSI 50Hz 4:3 643643643637----597284-------763------- - -
H POSI 50Hz 4:3 OTHER 643 643 643 640 - - - - 597 284 307 256 - - - - - 76 3 146 94 ----- - -
H POSI 60Hz 4:3
H POSI CENTER (PC) 583 583 583 590 553 266 - - - - - - 52 2 2 - - - - - - 131 147 192 280 204 302 344
H POSI 60Hz 4:3 OTHER 584 584 584 592 553 266 306 256 - - - - 52 2 2 92 33 - - - - 130 146 192 280 - - -
22 H POSI MAX (PC) - - - - - - - - - - - - - - - - - - - - - 181 197 242 330 254 352 394
23 H POSI MIN (PC) - - - - - - - - - - - - - - - - - - - - - 81 97 142 230 154 252 294
V POSI 50Hz FULL SCREEN/
Cinema OTHER 27272726----27542218-----16421219----- - -
V POSI 50Hz FULL SCREEN -------------------------- - -
V POSI 50Hz Cinema -------------------------- - -
V POSI 60Hz FULL SCREEN/Cinema OTHER
/V POSI CENTER(PC) 21 21 21 20 21 44 20 18 - - - - 10 31 34 22 19 - - - - 28 26 26 25 32 25 17
V POSI 60Hz FULL SCREEN -------------------------- - -
V POSI 60Hz Cinema -------------------------- - -
25 V POSI MAX - - - - - - - - - - - - - - - - - - - - - 53 51 51 50 57 50 42
26 V POSI MIN - - - - - - - - - - - - - - - - - - - - - 31107 0 0
27 BACKLIGHT CENTER 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128
28 BACKLIGHT MAX 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
29 BACKLIGHT MIN 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00000 0 0
30 BRIGHT CENTER + + + + -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 88888 8 8
31 BRIGHT MAX + + + + 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40
32 BRIGHT MIN + + + + -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64
33 TINT CENTER + + + + -6 -6 -6 -6 -6 -6 -6 -6 -6 -6 -6 -6 -6 -6 -6 -6 -6 -7 -7 -7 -7 -7 -7 -7
34 CONTRAST CENTER *+ *+ *+ *+ *41 *40 *39 *39 *41 *40 *39 *39 *40 *40 *40 *40 *35 *40 *40 *40 *40 39 39 39 39 39 39 39
35 CONTRAST MAX *+ *+ *+ *+ *59 *59 *55 *55 *56 *56 *55 *55 *56 *56 *56 *56 *56 *56 *56 *56 *56 53 53 53 53 53 53 53
36 CONTRAST MIN + + + + 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18
37 CONTRAST 50 *+ *+ *+ *+ *54 *52 *51 *51 *54 *52 *51 *51 *52 *52 *52 *52 *52 *52 *52 *52 *52 50 50 50 50 50 50 50
38 COLOR CENTER + + + + 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45
39 COLOR MAX + + + + 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63
40 COLOR MIN + + + + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00000 0 0
41 TEXT H POSI 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150
42 TEXT V POSI 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 77777 7 7
43 DAC VCOM 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0000000000 0 0
NOTE: For the step no. with * mark, please adjust it according to the situation of the set.
For the step no. with + mark, please adjust it according to the 2-4.
ELECTRICAL ADJUSTMENTS
PCHDMI(PAL)
24
CS(NTSC) CS(PAL) HDMI(NTSC)TUNER AV
21
D-3 D-4

2-4: Confirmation of Fixed Value (Step No.)
Please check if the fixed values of each of the ad
j
ustment item is set correctl
y
referrin
g
below. (TUNER/AV)
NO. FUNCTION PAL50 PAL60 SECAM PAL50 PAL60 SECAM NTSC3.58 NTSC4.43 PAL50 PAL60 SECAM NTSC3.58 NTSC4.43 PAL50 PAL60 SECAM NTSC3.58 NTSC4.43 PAL50 PAL60 SECAM NTSC3.58 NTSC4.43 PAL50 PAL60 SECAM NTSC3.58 NTSC4.43
Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No. Step No.
30 BRIGHT CENTER -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
31 BRIGHT MAX 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40
32 BRIGHT MIN -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64 -64
33 TINT CENTER -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4 -4
34 CONTRAST CENTER *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39 *39
35 CONTRAST MAX *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53 *53
36 CONTRAST MIN 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18
37 CONTRAST 40 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50 *50
38 COLOR CENTER 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45
39 COLOR MAX 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63 63
40 COLOR MIN 000000 0 0 000 0 0 0 00 0 0 000 0 0 000 0 0
NOTE: For the step no. with * mark, please ad
j
ust it accordin
g
to the situation of the set.
ELECTRICAL ADJUSTMENTS
480i
AV2(SCART2) AV3(RCA) AV1(SCART1)
S(Y/C) S(Y/C)
A-TU RGB
576i 480i
AV1(SCART1),AV2(SCART2) AV3(RCA)
CVBS CVBS 480i 576i 480i 576i576i 576i 480i 576i
D-5 D-6

CP3601
CP3603
CP4302
J4301
TU6001
J4205
J4206
CP3801
CP301
J4202
CP3802
J4204
J4203
CP4305
OS2201
CP2201
CP2202
J401
CP406
CP407
ELECTRICAL ADJUSTMENTS
3. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
D-7
LCD PANEL
POWER PCB
OPERATION PCB
MAIN PCB
CP4301
REMOCON PCB
AC IN
CD3810
CP411
CP412
SPEAKER CD4301
CP7201
CD7204
CD4302
CD403
CD404

SW_Y/D_Y
SW_PB/D_PB
SW_PR/D_PR
MAIN BLOCK DIAGRAM
PC/HDMI AUDIO IN
J4301
MSJ-035-39D_B_PC_LF(087)
PC/DVI1_A_N_L
PC/DVI1_A_IN_R
DVI2 AUDIO_L
DVI2 AUDIO_R
COMPONENT AUDIO IN
J4202
AV2-57A03-01
YUV AUDIO L
YUV AUDIO R
YUV/DVI/PC Lch SW
IC4303
NJM2534V(TE2)
YUV/DVI/PC Rch SW
IC4304
NJM2534V(TE2)
PC IN
CP4302
D229FD015G107BY
SW_A1_L
SW_A1_R
VGA_R
VGA_G
VGA_B
DECORDER/PERITEL
J4206
MRC-021V-27_PC
SCART1_V_IN
SCART2_V_IN
SCART1_R/C1_IN
SCART1_G_IN
SCART1_B_IN
SCART2_R/C2_IN
SCART2_G_IN
SCART2_B_IN
SCART1/2_VIDEO_SW
IC4206
MM1501XNRE
SW_SCART_CVBS/Y
SW_SCART_R/C
SW_SCART_G
SW_SCART_B
SCART1/2_RGB_SW
IC4204
NJM2584AM(TE1)
AUDIO_SCART1/2_LCH_SW
IC4203
MM1501XNRE
AUDIO_SCART1/2_RCH_SW
IC4202
MM1501XNRE
SC1_A_IN_L
SC2_A_IN_L
SC1_A_IN_R
SC2_A_IN_R
SW_A_L
SW_A_R
TUNER_VIDEO_OUT
SC1_A_OUT_L
SC1_A_OUT_R
SC2_A_OUT_L
SC2_A_OUT_R
MONITOR
SIF
TUNER
TU6001
TAFV-W623D
AV/AUDIO OUT/S-TERMINAL
J4204
RCA/DIN-501A-00B-03
YC IN
AUDIO_OUT_LR
VIDEO_AUDIO LR IN
S_JACK_Y
S_JACK_C
AUDIO JACK OUT L
AUDIO JACK OUT R
CVBS IN
VIDEO A L
VIDEO A R
MICON/SCALER
IC803
VCT6973G‑FA‑B3‑000
HDMI CONNECTOR
CP3601
HDMI CONNECTOR
CP3603
HDMI1 IN
HDMI2 IN
HDMI I/F
IC3605
SII9025CTU
DVI DATA8〜23
Y,Cb,Cr 16Bit
CP7201
20389-Y30E PANEL V2301
LC320W01-SL22
RGB RGB
SPEAKER
AUDIO OUT L
SPEAKER
AUDIO OUT R
AUDIO AMP
IC301
TDA8932T
HEADPHON AMP
IC300
NJM2151AV
(TE1)
HEADPHON JACK
J4205
MSJ-035-
08D_PC(087)
AMP L/R
HEADPHON
L/R
SPEAKER
SP301,SP302
FB136N4-A1
COMPONENT V IN
J4203
RCA-349-00D-01
E-1 E-2

POWER BLOCK DIAGRAM
10
18
8
POWER SW CTL
IC401 MP2A5060
Vcc
Q1
P-GND
AC IN
1
3
2
4
1
3
2
4
4
1
3
2
D431
F401 L401 L402
L403
AT+5V
RELAY
RY401
D408
RELAY_H
D427
D430D425
J401
TRANSFORMER
T402
3
1
4
5
8
9
2
4
5
1
+
C424
4
3
1
2
FEED BACK
IC410
PS2561AL1-1-V(W)
SW REG CTL
IC402 MIP2F4
2
7
3
TRANSFORMER
T401
18
17
14
13
10
1
3
REGULATOR
IC404 KIA431A-AT
Q416
CP412_7.AT+34
CP411_14,15.AT+5V
CP411_16.PWOER FAIL
CP411_1,2.SOUND+B
CP411_8,9.SW+12V
CP406_1,2,3,4,5.INV_SW+24V
Q413,Q419 CP412_8,9.LCD+B
E-3 E-4

1 53
105157
109
1
37 73
CMF111A
C806
NR802NR801
R827 R828
C857
C801
C803
C804
C892
C821 C837
R853 R845
R7206 R846
B7201
C7201
R839
R841
B817
R834 R833 R823
R824 R825 R826
C867
R818 R820
C849
C851
C853 C852
C854
C856
R807 R810
R885
C835
C826
C825
C834
C839
C824
C828
C820
C827
C838
C819
C830 C822 C840
C3232 C3228
D3205
R3213R3216
W815 W811
R3215 R3210
D3204
C3227 C3231
IC801
IC802
D804
C893
R866
R861
R865
R860
R864
R863
R859
R862
R857
R868
R855
R814
R819
IC803
R815 C831 C818
C842
R816 R867 R850
R813
R842
IC3203 IC3204
R811
C885 C884
X801
R3610 R3601
R3621
R3715
C3722
R3716
C3693 C3694R3698
R3697
X3602
D3601 D3603 D3627 D3626
CP3601
L3603
L3601
L3602 L3604
IC3605
NR3605NR3606
NR3604
NR3603
CP3603
L3608 L3607 L3606 L3605
C3633 D3602
C3705 C3707
C3654
NR3602
NR3601
B4305
R4321 R4315
CP4302
B4303
R4314
R4309B4304
R4320
R4312
C6014 C6006B6003
R3670
C3607
C3606
C3605
IC4303 IC4304
C3604
C3612
TU6001
C3702
C3703
IC3601
R3701 R3704 C3627
R3688
B4301 B4314
B4315
B4302
R4343
R4318
C4336
C4347
C4350 C4348R4347
R4317
C4339C4337
Q4306Q4303
R4334 R4329 C4356 C4328
L4305
C4353
R3613
C112
R4319
C4355 R4337
C3639
C3640
C3641
R3695 R3711
R6002R6003 C6011C6015
C3637
J4301
C3635 B3609 C3638
C3615
C3611
C3659
J4205
J4202
C4218 C4217
Q4209
R4232
R4229
B4200 C4229
J4206
Q4204 Q4208
Q4205 Q4210
R4268 R4264 R4261 R4267
C4238 C4241
C4242
Q4217
W888
R4284
Q4218
D4213 D4215 D4214
B4309 B4318 B4307
D4305
B4306
R4338
L4212 L4207
L4203 L4202 L4206
L4205 L4204 L4211
L4208 L4227
B4209 B4210
B4211 B4213 B4212
CP4301_1
IC300
C330
IC301
CP3801
C319
C363
C366R330C368
Q300
CP301
R311
Q302 Q301
R325
C320
R316
C318 C314 C310 C307
C379
C317 C316 C315 R309 R303 R301 R307
Q3205
IC3201
C3213
D3202
R3205C3212
C3211 R3211
R3212 R3238
C3815
R331 Q321
B3801
R3223
R3224
C3218
C3219
IC3802
C3837
R3827 R3828
Q3809
R3801 R3805
R3825
IC3801
W835
C384
C376
W806
W841
W883
R4218 C4220 R4227 C4230 R4242 C4233
Q4207
C365
C372 C380C370R332
C373 R334C381
C378
R317
R315
C326
C308
R4225
R4228
C322
R335
R333
B306
C300
B302
B303
B301
B304
R4254
D4212
C4277
IC3202
IC4202 IC4203
C4358
Q4309 Q4305
R4327
C334 C333
R4234 R4300
C4250
R4201
L3201
L3203
R302
R306
C4283_1
C3216
IC3205
C3238 C3240
C4239 L4230
C4294
Q4221
R4304 R4299
R4298
C4300
L4231
R4313 R4306
D3804
C337
C3201
C4295
C4299
C4363
B307
R3202 R3203
R6019 R6017 R6016 R6012
Q3206
C324C323
L3812
L4221 L4225
L4217
L4223
L4213
SH4307
SH4301 SH4302 SH4303 SH4304
L4224L4232
C4285 C4374 R4276 R4287
SH4306
SH4305
CP3802
IC4204
IC4206
R4272
L4219
C4379
R4349
D4220
C4265
D4216
R4290
C4381
R4346
D4218
C4281 C4377
C4380
C4384
C4383
L4233
C4385
J4204
R4230
B4205 B4214 R4353
R4352
W873
C3242
W843
CP802
Q3602
R3635
C3643
R3632
C3642
Q3601
R3633
R3636
R883
C3618
W829
R878
C3804
R830
D3209
D3210
Q3202
Q101 Q102
C3241
R4351
W876
W889
CP7201
W803
R129 R128
C858 C859 C861 C862 C863 C864
R887
R888
R890R889
J4203
R4355
L3202_1
L302_1
L300_1
C4359
R4358
C4297
C4287
C4288
R7207
R7205
W912 W826
W864 W849 W850 W851
W925
W886
W813
W818
W809
W814
W819
CP4305_1
D4247
D4255 D4258
D4256
D4241
D4259
D4223
D4222
S803X
S803Y
PRINTED CIRCUIT BOARDS
MAIN (TOP SIDE)
F-1 F-2