Toshiba 15SZ2E User manual

SERVICE MANUAL
Color Television
15SZ2E/15SZ2H
15CSZ2R
S3E Chassis
FILE NO. 060-200317
Jan., 2004

– 2 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
TABLE OF CONTENTS
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS ........................................................................................................................................ 3
SET-UP ADJUSTMENT ............................................................................................................................................ 4
SERVICE MODE ...................................................................................................................................................... 6
DESIGN MODE ........................................................................................................................................................ 9
ELECTRICAL ADJUSTMENTS .............................................................................................................................. 10
CIRCUIT CHECK .................................................................................................................................................... 12
CHAPTER 2 SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA .............................................................................................................................. 13
LOCATION OF CONTROLS ................................................................................................................................... 14
PROGRAMMING CHANNEL MEMORY................................................................................................................. 15
CHASSIS AND CABINET REPLACEMENT PARTS LIST ......................................................................................17
PC BOARDS BOTTOM VIEW ................................................................................................................................. 23
TERMINAL VIEW OF TRANSISTORS ................................................................................................................... 25
CIRCUIT BLOCK DIAGRAM .................................................................................................................................. 28
SPECIFICATIONS .............................................................................................................................................. END
APPENDIX:
CIRCUIT DIAGRAM

–3 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION”AND “PRODUCT SAFETY NOTICE”INSTRUCTIONS BELOW.
X-RAY RADIATION PRECAUTION
1. Excessive high voltage can produce potentially hazard-
ous X-RAY RADIATION. To avoid such hazards, the high
voltage must not be above the specified limit. The nominal
value of the high voltage of this receiver is (A) kV at zero
beam current (minimum brightness) under a (C) V AC power
source. The high voltage must not, under any circum-
stances, exceed (B) kV.
Refer to table-1 for high voltage (A), (B) & AC voltage (C).
(See SETTING & ADJUSTING DATA on page 13)
Each time a receiver requires servicing, the high voltage
should be checked following the HIGH VOLTAGE CHECK
procedure in this manual. It is recommended that the read-
ing of the high voltage be recorded as a part of the service
record. It is important to use an accurate and reliable high
voltage meter.
2. The only source of X-RAY RADIATION in this TV receiver
is the picture tube. For continued X-RAY RADIATION pro-
tection, the replacement tube must be exactly the same
type tube as specified in the parts list.
3. Some part in this receiver have special safety-related char-
acteristics for X-RAY RADIATION protection. For contin-
ued safety, parts replacement should be undertaken only
after referring to the PRODUCT SAFETY NOTICE below.
SAFETY PRECAUTION
WARNING : Service should not be attempted by anyone unfamiliar with the necessary precautions on this receiver. The following
are the necessary precautions to be observed before servicing this chassis.
1. An isolation transformer should be connected in the power line between the receiver and the AC line before any service is
performed on the receiver.
2. Always discharge the picture tube anode to the CRT conductive coating before handling the picture tube. The picture tube
is highly evacuated and if broken, glass fragments will be violently expelled. Use shatter proof goggles and keep picture tube
away from the unprotected body while handling.
3. When replacing a chassis in the cabinet, always be certain that all the protective devices are put back in place, such as; non-
metallic control knobs, insulating covers, shields, isolation resistor-capacitor network etc.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are
often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using
replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety char-
acteristics are identified in this manual and its supplements; electrical components having such features are identified by
the international hazard symbols on the schematic diagram and the parts list.
Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement
parts which do not have the same safety characteristics as specified in the parts list may create shock, fire, X-ray
radiation or other hazards.

–4 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION”AND “PRODUCT SAFETY NOTICE”ON PAGE 3 OF THIS MANUAL.
SET-UP ADJUSTMENT
■The following adjustments should be made when a complete realignment is required or a new picture tube is installed.
Perform the adjustments in order as follows :
1. Color Purity
2. Convergence
3. White Balance
Note: The PURITY/CONVERGENCE MAGNET assembly and rubber wedges need mechanical positioning.
Refer to figure 1.
Mounting position of the purity magnet assembly should fit to same position as old one because slightly difference to
the position depend on a kind of tube.
*There are no adjustment of purity and convergence in some picture tube (Unified with purity magnet)
GLASS CLOTH
TAPES
DEFLECTION
YOKE
TEMPORARY
MOUNTING
RUBBER WEDGE
ADHESIVE
DEFLECTION
YOKE
PURITY/
CONVERGENCE
MAGNET ASS'Y
29.1mm(28", 29")
25mm(25")
19mm(19", 20", 21")
14mm(13", 14")
Figure 1.
COLOR PURITY ADJUSTMENT
NOTE : Before attempting any purity adjustments, the receiver
should be operated for at least fifteen minutes.
1. Demagnetize the picture tube and cabinet using a degauss-
ing coil.
2. Set the brightness and contrast to maximum.
3. Use a green raster from among the built-in test signals.
4. Loosen the clamp screw holding the yoke and slide the
yoke backward or forward to provide vertical green belt
(zone) in the picture screen.
5. Remove the Rubber Wedges.
6. Rotate and spread the tabs of the purity magnet (See fig-
ure 2.) around the neck of the picture tube until the green
belt is in the center of the screen. At the same time, enter
the raster vertically.
7. Slowly move the yoke forward or backward until a uniform
green screen is obtained. Tighten the clamp screw of the
yoke temporarily.
8. Check the purity of the red and blue raster.

–5 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
CONVERGENCE ADJUSTMENTS
NOTE: Before attempting any convergence adjustments, the
receiver should be operated for at least fifteen min-
utes.
■CENTER CONVERGENCE ADJUSTMENT
1. Use the cross-dot pattern from among the built-in test sig-
nals.
2. Set the brightness and contrast for well defined pattern.
3. Adjust two tabs of the 4-Pole Magnets to change the an-
gle between them (See figure 2.) and superimpose red
and blue vertical lines in the center area of the picture
screen.
4. Turn the both tabs at the same time keeping the angle
constant to superimpose red and blue horizontal lines at
the center of the screen.
5. Adjust two tabs of 6-Pole Magnets to superimpose red/
blue line and green one. Adjusting the angle affects the
vertical lines and rotating both magnets affects the hori-
zontal lines.
6. Repeat adjustments 3, 4, 5 keeping in mind red, green
and blue movement, because 4-Pole Magnets and 6-Pole
Magnets have mutual interaction and make dot movement
complex.
■CIRCUMFERENCE CONVERGENCE ADJUSTMENT
1. Loosen the clamping screw of deflection yoke slightly to
allow the yoke to tilt.
2. Temporarily put a wedge as shown in figure 1. (Do not
remove cover paper on adhesive part of the wedge.)
3. Tilt front of the deflection yoke up or down to obtain better
convergence in circumference. (See figure 3.) Push the
mounted wedge into the space between picture tube and
the yoke to fix the yoke temporarily.
4. Put other wedge into bottom space and remove the cover
paper to stick.
5. Tilt front of the yoke right or left to obtain better conver-
gence in circumference. (See figure 3.)
6. Keep the yoke position and put another wedge in either
upper space. Remove cover paper and stick the wedge
on picture tube to fix the yoke.
7. Detach the temporarily mounted wedge and put it in an-
other upper space. Stick it on picture tube to fix the yoke.
8. After fixing three wedges, recheck overall convergence.
Tighten the screw firmly to fix the yoke and check the yoke
is firm.
9. Stick three adhesive tapes on wedges as shown in figure
1.
Figure 2.
BLU RED
BLU
RED
RED/BLU GRN
RED/BLU
GRN
B
G
R
R
G
B
BGR
RGB
BGR
RGB
R
G
B
B
G
R
4-POLE MAGNETS MOVEMENT
INCLINE THE YOKE UP (OR DOWN)
6-POLE MAGNETS MOVEMENT
Center Convergence by Convergence Magnets
Circumference Convergence by DEF Yoke
INCLINE THE YOKE RIGHT (OR LEFT)
Figure 3. Dot Movement Pattern
4-POLE
MAGNETS
PURITY
MAGNETS
6-POLE
MAGNETS
ADJUST THE ANGLE
(VERTICAL LINES) FIXED
ROTATE TWO TABS
AT THE SAME TIME
(HORIZONTAL LINES)
CONVERGENCE MAGNET ASSEMBLY ADJUSTMENT OF MAGNETS

–6 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
SERVICE MODE
1. ENTERING TO SERVICE MODE
S
(Service mode display)
Item
Data
3) While pressing the obutton,
press MENU button on TV set.
2) Press obutton again to
keep pressing.
2. DISPLAYING THE ADJUSTMENT MENU
1) Press MENU button on TV.
3. KEY FUNCTION IN THE SERVICE MODE
The following key entry during display of adjustment menu provides special functions.
A single horizontal line ON/OFF: - / - - button (on Remote) or abutton (on TV)
Test signal selection : abutton (on Remote)
Selection of the adjustment items : Channel s/t(on TV or Remote)
Change of the data value : Volume ;+/–(on TV or Remote)
Adjustment menu mode ON/OFF : MENU button (on TV)
Initialization of the memory (QA02) : CALL + Channel button on TV (s)
Reset the count of operating protect
circuit to “00”: CALL + Channel button on TV (t)
“RCUT”selection : 1 button
“GCUT”selection : 2 button
“BCUT”selection : 3 button
“CNTX”(or “SCNT”) selection : 4 button
“COLC”selection : 5 button
“TNTC”selection : 6 button
Test audio signal ON/OFF (1kHz) : 8 button
Self diagnostic display ON/OFF : 9 button
1) Press obutton once on
Remote Control.
Adjustment mode
Press
Press
Service mode
Item
Data
S
Color thickness correction
note: Displayed differently as shown below, de-
pending on the setting of the receiving color
system.
COLP (PAL)
COLC (NTSC)
COLS (SECAM)
CAUTION : Never try to perform initialization unless you have changed the memory IC.

–7 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
4. SELECTING THE ADJUSTING ITEMS
1) Every pressing of CHANNEL sbutton in the service mode changes the adjustment items in the order of table-2.
(tbutton for reverse order)
Refer to table-2 for preset data of adjustment mode.
(See SETTING & ADJUSTING DATA on page 13)
5. ADJUSTING THE DATA
1) Pressing of VOLUME ;+/–button will change the value of data in the range from 00H to FFH. The variable
range depends on the adjusting item.
6. EXIT FROM SERVICE MODE
1) Pressing POWER button to turn off the TV once.
■INITIALIZATION OF MEMORY DATA OF QA02
After replacing QA02, the following initialization is required.
1. Enter the service mode, then select any register item.
2. Press and hold the CALL button on the Remote, then press the CHANNEL sbutton on the TV. The initialization of QA02 has
been complated.
3. Check the picture carefully. If necessary, adjust any adjustment item above.
Perform “Auto search Memory”on the owner’s manual.
CAUTION: Never attempt to initialize the data unless QA02 has been replaced.
7. TEST SIGNAL SELECTION
1) Every pressing of abutton on the Remote Control changes the built-in test patterns on screen as described below
in SERVICE MODE.
Signals Picture
•Red raster
•Green raster
•Blue raster
•All Black
•All White
•Black & White
•Black cross-hatch
•White cross-hatch
•Black cross-dot
•White cross-dot
•Black cross-bar
•White cross-bar
•Black cross-bar
on green raster
•H signal (white)
•H signal (black)
* The signals marked with are not usable to display in the Test signal for some model.
Signal off NTSC signals (14 patterns)
PAL signals (14 patterns)

–8 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
8. SELF DIAGNOSTIC FUNCTION
1) Press “9”button on Remote Control during display of adjustment menu in the service mode.
The diagnosis will begin to check if interface among IC’s are executed properly.
2) During diagnosis, the following displays are shown.
23******
POWER : 00
BUS LINE : OK
BUS CONT : OK
BLOCK : UV V1
QT01
<SELF CHECK>
Part number of microprocessor(QA01)
Operation number of protecting circuit ----“00”is nor-
mal.
When indication is other than “00”, overcurrent apts to
flow, and circuit parts may possibly be damaged.
BUS LINE CHECK ----“OK”is normal.
“SDA1-GND”------------- SDA-GND short circuit.
“SCL1-GND”-------------- SCL-GND short circuit.
“SCL1-SDA1”------------- SCL-SDA short circuit.
BUS CONT ----“OK”is normal.
When indication shows “Q uuu NG”, the device with
the number may possibly be damaged.
BLOCK
UV : TV reception mode
V1 : VIDEO input mode (a1)
Indicated color of mode now selected : Green and Red
Indicated color of other modes : White
Green : Normal
Red : The microprocessor operates to provide judgement
of no video signal. The red color is still indicated
though the signal is input, failure may exist in input
signal line including QT01.
QT01 : In case of indication green ---Normal
In case of indication red with input signal----
Failure may exist in output line including QV01.
NOTE: Component which controls character display on
screen is QT01. If this display function fails to op-
erate due to damage in QT01, self diagnosis pro-
cedure is as follows.
(1) In case that power indicator is blinking with
interval of 0.5 seconds; it means protecting cir-
cuit (Current limiter) is operating, and circuit
components may possibly be damaged. Check
related components.
(2) In case that power indicator is blinking with
interval of 1 second; Protecting circuit does
not operate, but a part of Bus line does not
operate normally. Check Bus line.





* The items marked with are not usable to display in the SELF DIAGNOSTIC FUNCTION for some model.

–9 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
DESIGN MODE
1. ENTERING TO DESIGN MODE
ITEM
DATA
S D Press
(Design mode) (Adjustment mode)
Press
3) Press MENU button on TV.
2) While pressing o(or CALL) button on
Remote and press MENU button on TV.
1) Select the Service mode.
2. SELECTING THE ADJUSTING ITEMS
Every pressing of CHANNEL tbutton in the design mode changes the adjustment items in the order of table-3.
(sbutton for reverse order)
Refer to table-3 for data of design mode.
(See SETTING & ADJUSTING DATA on page 13)
3. ADJUSTING THE DATA
Pressing of VOLUME sor tbutton will change the value of data.
When QA02 is initialized, items “OPT0”and “OPT1”of DESIGN MODE are set to the data of the representative model of this
chassis family.
Therefore, because ON-SCREEN specification remains in the state of the representative of model. This model is required to
reset the data of items “OPT0”and “OPT1”.

–10 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
ELECTRICAL ADJUSTMENTS
1. Enter the service mode, then select any register item.
2. Press the TV/VIDEO button on the Remote until the black cross-bar pattern ap-
pears on the screen.
3. Adjust the FOCUS control (on T461) for well defined scanning lines on the picture
screen.
FOCUS VR ADJ
SUB-BRIGHTNESS
(BRTC)
Note: Constrict the picture height
until the vertical retrace line
appears adjusting the item
HIT (HEIGHT).
1. Set CONTRAST to minimum, and
BRIGHTNESS to center by adjusting
user controls.
2. Set the TV in service mode to get white
cross-bar of inside pattern.
3. Select BRTC (brightness correction),
and adjust the ;–/+ button to reduce
the value so that white portion of inside
pattern slightly light.
4. Adjust ;–/+ button to increase the
data value of BRTC, and set it just
before the difference between the belt of
vertical retrace and the border of black
portion of inside pattern is visible.
After that, return vertical height and
contrast.
ITEM ADJUSTMENT PROCEDURE
Belt of vertical retrace
HORIZONTAL POSITION
ADJUSTMENT (HPOS)
VERTICAL POSITION
ADJUSTMENT (VPOS)
1. Set the TV in service mode, and get
black or white cross-bar signal with
VIDEO button on remote hand unit.
2. Select either HPOS (Horizontal
picture phase) or VPOS (Vertical
picture phase) with CHANNEL s, t
buttons, and adjust horizontal or
vertical picture position in the center
of screen with VOLUME ;–/+
buttons.
VERTICAL AMPLITUDE
ADJUSTMENT (HIT)
1. Set the TV in service mode, and get
black or white cross-hatch signal
with VIDEO button on remote hand
unit.
2. Select HIT (Vertical amplitude) with
CHANNEL s, tbuttons, and adjust
vertical amplitude with VOLUME
;–/+ buttons so that vertical am-
plitude lacks a little.
3. Adjust vertical amplitude with VOL-
UME ;–/+ buttons so that the first
bar on cross-hatch signal touches
edge of screen.
The first

–11 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
ITEM ADJUSTMENT PROCEDURE
WHITE BALANCE
ADJUSTMENT
•CUTOFF ADJUSTMENT
(RCUT)
(GCUT)
(BCUT)
•DRIVE ADJUSTMENT
(GDRV)
(BDRV)
1. Set Contrast to 40, and brightness to +20 by picture control.
2. Set the TV in service mode, and get the inside W/B adjusting signal with VIDEO
button.
3. Select RCUT, GCUT and BCUT with CHANNEL s, tbuttons, to set individual
values to Initial reference data, and to set GDRV and BDRV to Initial reference
data with VOLUME ;–/+ buttons.
4. Press -/- - button on the remote control and rotate Screen VR to get one slight
horizontal line on screen.
Note: Every pressing of -/- - button provides Horizontal line picture and Normal
picture alternately.
5. Press -/- - button to release horizontal line picture, and select the two other colors
which did not light in the above step with CHANNEL s, tbuttons. Then tap VOL-
UME ;–/+ buttons so that three colors slightly light in the same level.
XTo correct white balance in light area,
select GDRV and BDRV with CHANNEL
s, tbuttons to adjust.
XTo correct white balance in dark area,
perform fine adjustment of RCUT, GCUT
and BCUT.
Light area check
(to show white)
Dark area check
(to show black)
NOTE: It is released built-in test pattern by changing the adjustment item for some model.
In this case, select the adjustment item with channel stbuttons first and then select the built-in test pattern with
-/- - button.

–12 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
CIRCUIT CHECK
HIGH VOLTAGE CHECK
CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps
below.
1. Connect an accurate high voltage meter to the second anode of the picture tube.
2. Turn on the receiver. Set the BRIGHTNESS and CONTRAST controls to minimum (zero beam current).
3. High voltage must be measured below (B) kV.
Refer to table-1 for high voltage (B).
(See SETTING & ADJUSTING DATA on page 13)
4. Vary the BRIGHTNESS control to both extremes to be sure the high voltage does not exceed the limit under any conditions.

–13 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA
15"
HIGH VOLTAGE AT ZERO BEAM: (A) 23.6 kV
MAX HIGH VOLTAGE: (B) 25.5 kV
AC VOLTAGE (C) 110~240 V
CHAPTER 2 SPECIFIC INFORMATIONS
SAFETY INSTRUCTIONS
Table-1
SERVICE MODE
ADJUSTING ITEMS AND DATAS IN THE SERVICE MODE:
Table-2
DESIGN MODE
ADJUSTING ITEMS AND DATAS IN THE DESIGN MODE:
Data
Item Name of adjustment Preset Data 15" Remarks
Table-3
Item Adjustment Reference data
RCUT
GCUT
BCUT
GDRV
BDRV
BRTC
COLC
TNTC
COLP
COLS
SCNT
HPOS
VPOS
HIT
VLIN
SRY
SBY
RAGC
R CUTOFF (B/W)
G CUTOFF (B/W)
B CUTOFF (B/W)
G DRIVE
B DRIVE
SUB BRIGHT CEN
SUB COLOR CEN NTSC
SUB TINT CEN
SUB COLOR CEN PAL
SUB COLOR CEN SECAM
SUB CONTRAST
50Hz H-POSITION
V-POSITION
HEIGHT
V-LINEARITY
SECAM R-Y
SECAM-B-Y
RF AGC
20H
20H
20H
40H
40H
40H
30H
45H
09H
30H
08H
0DH
04H
1EH
0AH
08H
08H
2AH
Data
←
←
←
←
←
←
←
←
←
←
←
0BH
02H
←
←
←
←
←
* There are no adjusting items in the design mode.

–14 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
LOCATION OF CONTROLS (Representative: 15SZ2E)
Front
Remote
ba
c
de f g
h
ij
Names of Parts
fPower on/standby
0~9 Direct select
CHs/tChannel up/down,
Item select
; -/+ Volume up/down,
Menu select, Level adjust
-/-- Digit select
MENU Menu open
oSound mute
Picture control
aTV/VIDEO select
CALL On-screen on/off
RGYB
Game select
Red/Green/Yellow/Blue
Remote Controller
Main power
on/off
Infrared
sensor
Power
indicator
t c sChannel
select
t;s Volume
down/up
aTV/VIDEO
select
MENU Menu open
Headphone
jack
AUDIO Audio input
terminal
VIDEO Video input
terminal
TV Set
Note: The shaded buttons are not available
for this TV. If you press the button,
”MODE NOT AVAILABLE” will appear on
the screen.
0
3
7
5
6
4
!¡
1
2
9
8
1
2
3
4
5
6
7
8
9
!º
!¡
a
b
c
d
e
f
g
h
i
j

–15 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
PROGRAMMING CHANNEL MEMORY
•For easy Channel selection, the chosen Position should have the same number as Channel stored there. For this
operation, you may use the “SEARCH”and “SKIP”functions.
Example : Presetting Channel 12 to Position 12
Channel Preset
Auto search memory (ASM)
All the channels that can be received are preset
automatically.
Select the starting position for ASM. Press (0~9) or CH
s/t.
Set the correct broadcast system for your region. Press
MENU and ;–/+ to call up the “SET UP”menu D7 .
Set “COLOR”to “AUTO”and set “SOUND”according
to the table above using CHs/tand ;–/+.
Press MENU and ;–/+ to call up the “TUNING”menu
D8 . Select “ASM”, then press ;+ to start the search.
When the TV screen returns to the start position, the
procedure is complete.
1
2
3
Manual Search and Changing the assigned
position
1
2
3
1
2
3
Manual Search
Select Position 12.
Press CH s/trepeatedly until 12 is displayed. Or, press
-/-- twice to display “--”on the screen then press the “1”
and “2”buttons in this order.
Press MENU and ;–/+ to call up the “TUNING”menu
D8 . Press CH s/tand select “SEARCH”.
Press ;–/+ to search. Pressing “-”searches for chan-
nels at lower frequencies while pressing “+”searches
for channels at higher frequencies.
When Channel 12 is found, press CH s/tto select
“MEMORY”. Press “+”to complete the presetting.
Store Position
Select Channel 12.
Press (0~9) or CH s/tto find the position preset for
Channel 12.
When Channel 12 is selected, press MENU and
;–/+ to call up the “TUNING”menu D8 . Press CH
s/tand select “POSITION”. Press ;–/+ and set “PO-
SITION”to P012. Pressing “-”and “+”respectively de-
creases and increases the position number.
When Position 12 is found, press CH s/tto select
“MEMORY”. Press “+”to complete the presetting.

–16 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
•Under some reception conditions, fine tuning may be necessary to improve the picture quality. In such cases, adjust the
manual fine tuning (MFT).
•If the signal frequency is unstable due to environmental conditions, use auto fine tuning.
Skip Function
If you set “SKIP ON”for unnecessary position numbers, these
will be skipped when selecting channels using CH s/t.
Example : Skipping Channel 13
Select Position 13 using the same method for select-
ing Position 12 (above).
Press MENU and ;–/+ to call up the “SET UP”menu
D7 . Press CH s/tand select “SKIP”.
Press ;–/+ to switch the “SKIP”setting from “OFF”
to “ON”. This completes the setting for skipping Posi-
tion 13.
Note:
•When “SKIP”is ON, the Position number is prefixed by
“*”.
Example: *13. To confirm this, select Position 13 using
the -/-- and 0~9 buttons.
•If you want to restore a skipped position number,
select it using the -/-- and 0~9 buttons then switch the
“SKIP”setting to “OFF”as in step 2 above.
Manual fine tuning (MFT)
Press MENU and ;–/+ to call up the “TUNING”menu
D8 .
Press CH s/tand select “MFT”. Press ;–/+ to start
fine tuning. Pressing “-”fine tunes to a lower frequency
while pressing “+”fine tunes to a higher frequency.
1
2
1
2
Auto fine tuning (AFT)
Press MENU and ;–/+ to call up the “TUNING”menu
D8 .
Press CH s/tand select “AFT”. Press ;–/+ to switch
it to “ON”. This completes the setting.
Notes:
•When you operate MFT, AFT is switched OFF
automatically. If you switch on AFT after fine tuning
with MFT, MFT may be cancelled.
•AFT may be set independently for each Position.
1
2

Location Parts No. Description
No.
Location Parts No. Description
No.
– 17 –
SPECIFIC INFORMATIONS
CAPACITORS
C101 24794101 ELECTROLYTIC, 16V 100UF M (15CSZ2R)
C102 24794221 ELECTROIYTIC, 16V 220UF M
C103 24109103 CERAMIC CHIP, 50V B 0.01UF K
(15SZ2E/15CSZ2R)
C104 24105470 CERAMIC CHIP, 50V CH 47PF J
(15SZ2E/15CSZ2R)
C105 24105220 CERAMIC CHIP, 50V CH 22PF J (15CSZ2R)
C106 24796479 ELECTROLYTIC, 35V 4.7UF M
C107 24105220 CERAMIC CHIP, 50V CH 22PF J (15CSZ2R)
C108 24539474 PLASTIC FILM, 50V 0.47UF J
C109 24794100 ELECTROLYTIC, 16V 10UF M (15CSZ2R)
C110 24109103 CERAMIC CHIP, 50V B 0.01UF K (15CSZ2R)
C113 24109102 CERAMIC CHIP, 50V B 1000PF K (15CSZ2R)
C116 24109103 CERAMIC CHIP, 50V B 0.01UF K (15CSZ2R)
C118 24109102 CERAMIC CHIP, 50V B 1000PF K
C120 24794100 ELECTROLYTIC, 16V 10UF M
C121 24109103 CERAMIC CHIP, 50V B 0.01UF K
C123 24797010 ELECTROLYTIC, 50V 1UF M
C129 24109102 CERAMIC CHIP, 50V B 1000PF K
C130 24797479 ELECTROLYTIC, 50V 4.7UF M
C131 24814103 CERAMIC CHIP, 50V F 0.01UF Z
C132 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C133 24105101 CERAMIC CHIP, 50V CH 100PF J
C135 24109222 CERAMIC CHIP, 50V B 2200PF K
C136 24206228 ELECTROLYTIC, 50V 0.22UF M 7L 3A
C137 24100103 CERAMIC CHIP, 50V F 0.01UF Z
C141 24105101 CERAMIC CHIP, 50V CH 100PF J
C150 24814103 CERAMIC CHIP, 50V F 0.01UF Z
C170 24109103 CERAMIC CHIP, 50V B 0.01UF K
C171 24794100 ELECTROLYTIC, 16V 10UF M
C172 24794100 ELECTROLYTIC, 16V 10UF M
C173 24794100 ELECTROLYTIC, 16V 10UF M
C174 24105330 CERAMIC CHIP, 50V CH 33PF J
C175 24105330 CERAMIC CHIP, 50V CH 33PF J
C176 24105330 CERAMIC CHIP, 50V CH 33PF J
C189 24797478 ELECTROLYTIC, 50V 0.47UF M
C192 24797478 ELECTROLYTIC, 50V 0.47UF M
C216 24797010 ELECTROLYTIC, 50V 1UF M
C224 24794100 ELECTROLYTIC, 16V 10UF M
C226 24539104 PLASTIC FILM, 50V 0.1UF J
C227 24539104 PLASTIC FILM, 50V 0.1UF J
C231 24232103 CERAMIC DISC, 50V F 0.01UF Z
C232 24232103 CERAMIC DISC, 50V F 0.01UF Z
C305 24617915 ELECTROLYTIC, 50V 1UF K 3A LI
C306 24794102 ELECTROLYTIC, 16V 1000UF M
C307 24693473 PLASTIC FILM, 100V 0.047UF J
C308 24796101 ELECTROLYTIC, 35V 100UF M
C312 24796102 ELECTROLYTIC, 35V 1000UF M
C313 24082280 PLASTIC FILM, 100V 0.22UF J
C314 24212152 CERAMIC DISC, 50V B 1500PF K
C315 24539474 PLASTIC FILM, 50V 0.47UF J
C317 24214471 CERAMIC DISC, 500V B 470PF K
C320 24796101 ELECTROLYTIC, 35V 100UF M
C410 24693472 PLASTIC FILM, 100V 4700PF J
C417 24214102 CERAMIC DISC, 500V B 1000PF K
C420 24794220 ELECTROLYTIC, 16V 22UF M
C421 24666470 ELECTORLYTIC, 16V 47UF M 3A
C431 24797479 ELECTROLYTIC, 50V 4.7UF M
C432 24203100 ELECTORLYTIC, 16V 10UF M 7L 3A
C433 24100103 CERAMIC CHIP, 50V F 0.01UF Z
C434 24100103 CERAMIC CHIP, 50V F 0.01UF Z
C435 24763102 ELECTROLYTIC, 16V 1000UF M
C436 24797478 ELECTROLYTIC, 50V 0.47UF M
C437 24109822 CERAMIC CHIP, 50V B 8200PF K
C440 24503193 PLASTIC FILM, 1500VH 1000PF H
C442 24082990 PLASTIC FILM, 250V 0.33UF J
C444 24503273 PLASTIC FILM, 1500VH 7500PF H
C445 24693104 PLASTIC FILM, 100V 0.1UF J
C446 24679100 ELECTROLYTIC, 250V 10UF M 3A
C448 24640908 ELECTROLYTIC, 160V 33UF M 3A LI
C449 24794471 ELECTROLYTIC, 16V 470UF M
C463 24109152 CERAMIC CHIP, 50V B 1500PF K
C467 24829243 PLASTIC FILM, 400V 0.024UF J
C484 24591104 PLASTIC FILM, 50V 0.1UF J
C485 24591104 PLASTIC FILM, 50V 0.1UF J
C502 24591103 PLASTIC FILM, 50V 0.01UF J
C517 24794100 ELECTROLYTIC, 16V 10UF M
C523 24794100 ELECTROLYTIC, 16V 10UF M
C526 24109102 CERAMIC CHIP, 50V B 1000PF K
C528 24797478 ELECTROLYTIC, 50V 0.47UF M
C565 24109103 CERAMIC CHIP, 50V B 0.01UF K (15CSZ2R)
C566 24794471 ELECTROLYTIC, 16V 470UF M (15CSZ2R)
C610 24795100 ELECTROLYTIC, 25V 10UF M
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY
PRECAUTION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF THIS MANUAL.
CAUTION: The international hazard symbols “ ” in the schematic diagram and the parts list designate com-
ponents which have special characteristics important for safety and should be replaced only with types identical to
those in the original circuit or specified in the parts list. The mounting position of replacements is to be identical with
originals. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE. Do not
degrade the safety of the receiver through improper servicing.
NOTICE:
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model
number and Description.
• The PC board assembly with
*
mark is no longer available after the end of the production.
Model : 15SZ2E, 15SZ2H, 15CSZ2R
Capacitors ............. CD : Ceramic Disk PF : Plastic Film EL : Electrolytic
Resistors ............... CF : Carbon Film CC : Carbon Composition MF : Metal Film
OMF : Oxide Metal Film VR : Variable Resistor FR : Fusible Resistor
(All CD and PF capacitors are ±5%, 50V and all resistors, ±5%, 1/6W unless otherwise noted.)
CHASSIS AND CABINET REPLACEMENT PARTS LIST

SPECIFIC INFORMATIONS
Location Parts No. Description
No.
Location Parts No. Description
No.
–18 –
SPECIFIC INFORMATIONS
C613 24539104 PLASTIC FILM, 50V 0.1UF J
C631 24797478 ELECTROLYTIC, 50V 0.47UF M
C632 24591682 PLASTIC FILM, 50V 6800PF J
C633 24591393 PLASTIC FILM, 50V 0.039MF J
C634 24591103 PLASTIC FILM, 50V 0.01UF J
C660 24797478 ELECTROLYTIC, 50V 0.47UF M
C661 24591104 PLASTIC FILM, 50V 0.1UF J
C665 24073060 ELECTROLYTIC, 25V 4700UF M 3A
C667 24591104 PLASTIC FILM, 50V 0.1UF J
C668 24795471 ELECTROLYTIC, 25V 470UF M
C669 24797100 ELECTROLYTIC, 50V 10UF M
C673 24109103 CERAMIC CHIP, 50V B 0.01UF K (15CSZ2R)
*C801 24503507 PLASTIC FILM, AC275V 0.22UF K
C805 24092281 CERAMIC DISC, AC250V E 4700PF
C806 24092281 CERAMIC DISC, AC250V E 4700PF
C810 24086059 ELECTROLYTIC, 400V 270UF M 3D
*C813 24092555 CERAMIC DISC, AC250V E 1000PF M
*C814 24092555 CERAMIC DISC, AC250V E 1000PF M
C861 24214471 CERAMIC DISC, 500V B 470PF K
C864 24797101 ELECTROLYTIC, 50V 100UF M
C873 24092341 CERAMIC DISC, 2KV R 470PF K
C874 24591104 PLASTIC FILM, 50V 0.1UF J
C875 24109681 CERAMIC CHIP, 50V B 680PF K
C876 24109102 CERAMIC CHIP, 50V B 1000PF K
C877 24100103 CERAMIC CHIP, 50V F 0.01UF Z
C878 24092341 CERAMIC DISC, 2KV R 470PF K
C879 24797479 ELECTROLYTIC, 50V 4.7UF M
C880 24100103 CERAMIC CHIP, 50V F 0.01UF Z
C884 24640018 ELECTROLYTIC, 160V 220UF
C885 24214471 CERAMIC DISC, 500V B 470PF K
C886 24214471 CERAMIC DISC, 500V B 470PF K
C887 24795221 ELECTROLYTIC, 25V 220UF M
C889 24667102 ELECTROLYTIC, 25V 1000UF M 3A
C893 24092341 CERAMIC DISC, 2KV R 470PF K
*C896 24092553 CERAMIC DISC, AC250V B 470PF K
C897 24092557 CERAMIC DISC, AC250V E 2200PF M
C899 24539224 PLASTIC FILM, 50V 0.22UF J
C902 24092345 CERAMIC DISC, 2KV 1000PF K
C904 24109391 CERAMIC CHIP CK73B 50V 390PF K
C905 24109331 CERAMIC CHIP, 50V B 330PF K
C907 24109391 CERAMIC CHIP CK73B 50V 390PF K
C910 24669478 ELECTROLYTIC, 50V 0.47UF M 3A
C912 24763221 ELECTROLYTIC, 16V 220UF M
C913 24794100 ELECTROLYTIC, 16V 10UF M
C971 24794470 ELECTROLYTIC, 16V 47UF M
CA02 24105101 CERAMIC CHIP, 50V CH 100PF J
CA03 24105220 CERAMIC CHIP, 50V CH 22PF J
CA04 24105220 CERAMIC CHIP, 50V CH 22PF J
CA30 24105270 CERAMIC CHIP, 50V CH 27PF J
CA42 24794100 ELECTROLYTIC, 16V 10UF M
CA45 24109103 CERAMIC CHIP, 50V B 0.01UF K
CA51 24109272 CERAMIC CHIP, 50V B 2700PF K
CA52 24109152 CERAMIC CHIP, 50V B 1500PF K
CA53 24105181 CERAMIC CHIP, 50V CH 180PF J
CA54 24797330 ELECTROLYTIC, 50V 33UF M
CA55 24797010 ELECTROLYTIC, 50V 1UF M
CA58 24105101 CERAMIC CHIP, 50V CH 100PF J
CA60 24797479 ELECTROLYTIC, 50V 4.7UF M
CC01 24109103 CERAMIC CHIP, 50V B 0.01UF K
CC02 24109103 CERAMIC CHIP, 50V B 0.01UF K (15CSZ2R)
CC08 24105330 CERAMIC CHIP, 50V CH 33PF J (15CSZ2R)
CS01 24794220 ELECTROLYTIC, 16V 22UF M
CS02 24794100 ELECTROLYTIC, 16V 10UF M
CS04 24109102 CERAMIC CHIP, 50V B 1000PF K (15CSZ2R)
CS05 24109102 CERAMIC CHIP, 50V B 1000PF K (15CSZ2R)
CS07 24109102 CERAMIC CHIP, 50V B 1000PF K (15CSZ2R)
CS15 24109102 CERAMIC CHIP, 50V B 1000PF K (15CSZ2R)
CV10 24793471 ELECTROLYTIC, 10V 470UF M
CV11 24794220 ELECTROLYTIC, 16V 22UF M
RESISTORS
R101 24011563 CHIP, METAL FILM, 1/20W 56K OHM J
R102 24011123 CHIP, METAL FILM, 1/20W 12K OHM J
R105 24011331 CHIP, METAL FILM, 1/20W 330 OHM J
(15SZ2E/15SZ2H)
R105 24011121 CHIP, METAL FILM, 1/20W 120 OHM J
(15SZ2H)
R106 24011332 CHIP, METAL FILM, 1/20W 3.3K OHM J
R107 24011330 CHIP, METAL FILM, 1/20W 33 OHM J
(15SZ2E/15CSZ2R)
R108 24011272 CHIP, METAL FILM, 1/20W 2.7K OHM J
(15SZ2E/15SZ2H)
R108 24011122 CHIP, METAL FILM, 1/20W 1.2K OHM J
(15SZ2H)
R109 24011682 CHIP, METAL FILM, 1/20W 6.8K OHM J
R110 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
(15SZ2E/15SZ2H)
R110 24011681 CHIP, METAL FILM, 1/20W 680 OHM J
(15SZ2H)
R111 24011360 METAL FILM CHIP, 1/20W 36 J
(15SZ2E/15SZ2H)
R111 24011330 CHIP, METAL FILM, 1/20W 33 OHM J
(15SZ2H)
R112 24000445 CHIP JUMPER, 1608TYPE (15SZ2E/15SZ2H)
R112 24011221 CHIP, METAL FILM, 1/20W 220 OHM J
(15SZ2H)
R113 24011222 CHIP, METAL FILM, 1/20W 2.2K OHM J
R114 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J
R116 24011682 CHIP, METAL FILM, 1/20W 6.8K OHM J
R117 24011222 CHIP, METAL FILM, 1/20W 2.2K OHM J
R118 24011821 CHIP, METAL FILM, 1/20W 820 OHM J
(15SZ2H)
R120 24011684 CHIP, METAL FILM, 1/20W 680K OHM J
(15SZ2E/15SZ2H)
R121 24011221 CHIP, METAL FILM, 1/20W 220 OHM J
R122 24000445 CHIP JUMPER, 1608TYPE
R124 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
(15SZ2E/15CSZ2R)
R130 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R131 24011221 CHIP, METAL FILM, 1/20W 220 OHM J
R132 24011271 CHIP, METAL FILM, 1/20W 270 OHM J
R133 24011271 CHIP, METAL FILM, 1/20W 270 OHM J
R134 24011561 CHIP, METAL FILM, 1/20W 560 OHM J
R135 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R136 24011513 CHIP, METAL FILM, 1/20W 51K OHM J
R139 24011332 CHIP, METAL FILM, 1/20W 3.3K OHM J
R140 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R141 24011331 CHIP, METAL FILM, 1/20W 330 OHM J
R142 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R143 24011333 CHIP, METAL FILM, 1/20W 33K OHM J
R144 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R145 24011303 CHIP, METAL FILM, 1/20W 30K OHM J
R146 24011224 CHIP, METAL FILM, 1/20W 220K OHM J
R147 24011152 CHIP, METAL FILM, 1/20W 1.5K OHM J
R148 24011222 CHIP, METAL FILM, 1/20W 2.2K OHM J
R149 24011684 CHIP, METAL FILM, 1/20W 680K OHM J
(15CSZ2R)
R150 24000445 CHIP JUMPER, 1608TYPE
R156 24553153 OXIDE METAL FILM, 1W 15K OHM J
R158 24011152 CHIP, METAL FILM, 1/20W 1.5K OHM J
R166 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R167 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R168 24011473 CHIP, METAL FILM, 1/20W 47K OHM J
R169 24011102 CHIP, METAL FILM, 1/20W 1K OHM J

–19 –
Location Parts No. Description
No.
Location Parts No. Description
No.
SPECIFIC INFORMATIONS
R171 24011473 CHIP, METAL FILM, 1/20W 47K OHM J
R172 24011162 CHIP, METAL FILM, 1/20W 1.6K OHM J
R173 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R174 24011473 CHIP, METAL FILM, 1/20W 47K OHM J
R175 24011223 CHIP, METAL FILM, 1/20W 22K OHM J
R176 24011473 CHIP, METAL FILM, 1/20W 47K OHM J
R177 24011223 CHIP, METAL FILM, 1/20W 22K OHM J
R178 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R179 24011222 CHIP, METAL FILM, 1/20W 2.2K OHM J
R180 24011473 CHIP, METAL FILM, 1/20W 47K OHM J
R181 24011223 CHIP, METAL FILM, 1/20W 22K OHM J
R182 24011162 CHIP, METAL FILM, 1/20W 1.6K OHM J
R190 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R191 24011330 CHIP, METAL FILM, 1/20W 33 OHM J
R192 24011330 CHIP, METAL FILM, 1/20W 33 OHM J
R194 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R196 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R217 24011104 CHIP, METAL FILM, 1/20W 100K OHM J
R227 24366223 CARBON FILM, 1/6W 22K OHM J
R228 24000445 CHIP JUMPER, 1608TYPE
R229 24000445 CHIP JUMPER, 1608TYPE
R230 24000445 CHIP JUMPER, 1608TYPE
R301 24366163 CARBON FILM, 1/6W 16K OHM J
R305 24323109 OXIDE METAL FILM, 2W 1 OHM J
R306 24366623 CARBON FILM, 1/6W 62K OHM J
R307 24366103 CARBON FILM, 1/6W 10K OHM J
R312 24552122 OXIDE METAL FILM, 1/2W 1.2K OHM J
R313 24366473 CARBON FILM, 1/6W 47K OHM J
R316 24011392 CHIP, METAL FILM, 1/20W 3.9K OHM J
R317 24011392 CHIP, METAL FILM, 1/20W 3.9K OHM J
R333 24547829 FUSIBLE, 1W 8.2 OHM J
R336 24383331 OXIDE METAL FILM, 2W 330 OHM J
R410 24011181 CHIP, METAL FILM, 1/20W 180 OHM J
R411 24011561 CHIP, METAL FILM, 1/20W 560 OHM J
R412 24366560 CARBON FILM, 1/6W 56 OHM J
R416 24019323 OXIDE METAL FILM, 5W 1.8K OHM J
R421 24011391 CHIP, METAL FILM, 1/20W 390 OHM J
R430 24366103 CARBON FILM, 1/6W 10K OHM J
R431 24531120 FUSIBLE, 1/2W 12 OHM J
R432 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J
R433 24011182 CHIP, METAL FILM, 1/20W 1.8K OHM J
R434 24552271 OXIDE METAL FILM, 1/2W 270 OHM J
R435 24011822 CHIP, METAL FILM, 1/20W 8.2K OHM J
R437 24366103 CARBON FILM, 1/6W 10K OHM J
R441 24532102 FUSIBLE, 1W 1K OHM J
R447 24553472 OXIDE METAL FILM, 1W 4.7K OHM J
R448 24321228 OXIDE METAL FILM, 1/2W 0.22 OHM J
R479 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R491 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R607 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R622 24000445 CHIP JUMPER, 1608TYPE
R630 24011123 CHIP, METAL FILM, 1/20W 12K OHM J
R631 24011822 CHIP, METAL FILM, 1/20W 8.2K OHM J
R632 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J
R662 24552221 OXIDE METAL FILM, 1/2W 220 OHM J
R663 24552221 OXIDE METAL FILM, 1/2W 220 OHM J
R664 24366339 CARBON FILM, 1/6W 3.3 OHM J
R665 24011224 CHIP, METAL FILM, 1/20W 220K OHM J
*R801 24009954 METAL FILN, 1/2W 2.2M OHM J
*R808 24019476 THERMISTOR, POSITIVE, AC290V 18 OHM M
R810 24568229 CERAMIC COVERED, 7W 2.2 OHM J
R816 24366471 CARBON FILM, 1/6W 470 OHM J
R817 24366331 CARBON FILM, 1/6W 330 OHM J
R840 24366362 CARBON FILM, 1/6W 3.6K OHM J
R860 24383104 OXIDE METAL FILM, 2W 100K OHM J
R861 24011683 CHIP, METAL FILM, 1/20W 68K OHM J
R864 24310479 OXIDE METAL FILM, 1/2W 4.7 OHM J
R873 24011562 CHIP, METAL FILM, 1/20W 5.6K OHM J
R874 24322398 OXIDE METAL FILM, 1W 0.39 OHM J
R875 24322398 OXIDE METAL FILM, 1W 0.39 OHM J
R876 24011221 CHIP, METAL FILM, 1/20W 220 OHM J
R877 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R880 24366562 CARBON FILM, 1/6W 5.6K OHM J
R881 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R885 24546228 FUSIBLE, 1/2W 0.22 OHM J
*R899 24004718 METAL GLAZE, 1/2W 8R2M J
R901 24552122 OXIDE METAL FILM, 1/2W 1.2K OHM J
R902 24552122 OXIDE METAL FILM, 1/2W 1.2K OHM J
R903 24552122 OXIDE METAL FILM, 1/2W 1.2K OHM J
R904 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J
R905 24011150 CHIP, METAL FILM, 1/2OW 15 OHM J
R914 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R915 24011681 CHIP, METAL FILM, 1/20W 680 OHM J
R917 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R920 24000874 FUSE 1W 439J
R921 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R922 24011681 CHIP, METAL FILM, 1/20W 680 OHM J
R925 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R928 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R929 24011681 CHIP, METAL FILM, 1/20W 680 OHM J
R931 24366229 CARBON FILM, 1/6W 2.2 OHM J
R936 24011272 CHIP, METAL FILM, 1/20W 2.7K OHM J
R937 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R938 24552560 OXIDE METAL FILM, 1/2W 56 OHM J
R960 24383183 OXIDE METAL FILM, 2W 18K OHM J
R961 24383183 OXIDE METAL FILM, 2W 18K OHM J
R963 24383183 OXIDE METAL FILM, 2W 18K OHM J
R972 24011331 CHIP, METAL FILM, 1/20W 330 OHM J
R974 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R977 24011681 CHIP, METAL FILM, 1/20W 680 OHM J
RA01 24011331 CHIP, METAL FILM, 1/20W 330 OHM J
RA02 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
RA03 24000445 CHIP JUMPER, 1608TYPE
RA06 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
RA07 24000445 CHIP JUMPER, 1608TYPE
RA35 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
RA36 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
RA37 24011223 CHIP, METAL FILM, 1/20W 22K OHM J
RA41 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
RA42 24011222 CHIP, METAL FILM, 1/20W 2.2K OHM J
RA43 24011332 CHIP, METAL FILM, 1/20W 3.3K OHM J
RA51 24011392 CHIP, METAL FILM, 1/20W 3.9K OHM J
RA52 24011392 CHIP, METAL FILM, 1/20W 3.9K OHM J
RA53 24011123 CHIP, METAL FILM, 1/20W 12K OHM J
RA54 24011471 CHIP, METAL FILM, 1/20W 470 OHM J
RA55 24011683 CHIP, METAL FILM, 1/20W 68K OHM J
RA56 24011564 CHIP, METAL FILM, 1/20W 560K OHM J
RA57 24011681 CHIP, METAL FILM, 1/20W 680 OHM J
RA60 24011362 CHIP, METAL FILM, 1/20W 3.6K OHM J
RA61 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
RA62 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
RA63 24011332 CHIP, METAL FILM, 1/20W 3.3K OHM J
RA71 24367163 CARBON FILM, 1/6W 16K OHM G
RA72 24367113 CARBON FILM, 1/2W 11K OHM J
RA73 24367562 CARBON FILM, 1/6W 5.6K OHM G
RA74 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
RA75 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
RA76 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J
RA77 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J
RA78 24367114 CARBON FILM, 1/6W 110K OHM G
RA79 24367303 CARBON FILM, 1/6W 30K OHM G
RA89 24000445 CHIP JUMPER, 1608TYPE
RB01 24011271 CHIP, METAL FILM, 1/20W 270 OHM J
RB09 24000445 CHIP JUMPER, 1608TYPE

–20 –
Location Parts No. Description
No.
Location Parts No. Description
No.
SPECIFIC INFORMATIONS
RB30 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
RC02 24000445 CHIP JUMPER, 1608TYPE (15SZ2E/15SZ2H)
RC02 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
(15CSZ2R)
RS02 24011471 CHIP, METAL FILM, 1/20W 470 OHM J
RS04 24011223 CHIP, METAL FILM, 1/20W 22K OHM J
RS06 24000445 CHIP JUMPER, 1608TYPE
RV02 24011750 CHIP, METAL FILM, 1/20W 75 OHM J
RV11 24011750 CHIP, METAL FILM, 1/20W 75 OHM J
RV12 24011181 CHIP, METAL FILM, 1/20W 180 OHM J
RV13 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
COILS & TRANSFORMERS
L101 23289929 COIL, PEAKING COIL 82MMH, TRF4820AU
(15CSZ2R)
L102 23238562 COIL, PEAKING, TRF4109AJ
(15SZ2E/15CSZ2R)
L103 23238503 COIL, PEAKING, TRF4129AJ
(15SZ2E/15SZ2H)
L103 23238558 COIL, PEAKING, TRF4R47AJ (15SZ2H)
L104 23238506 COIL, PEAKING, TRF4229AJ (15CSZ2R)
L105 23238506 COIL, PEAKING, TRF4229AJ (15CSZ2R)
L106 23238713 COIL, PEAKING, TRF4120AJ
L107 23238713 COIL, PEAKING, TRF4120AJ
L108 23238709 COIL, PEAKING, TRF4270AJ
L301 23103249 CORE, FERRITE BEAD 3.5X4.5, TEM2011AO
L441 23233987 COIL, LINEARITY, TLN2112AC
L462 23231352 COIL, DEFLECTION YOKE, TDY-6159A
L462A 23993696 BOARD, CORRECTION
L462C 23199314 COMPENSATOR, DEFLECTION YOKE
L462D 23006010 FERRITE SHEET, SPOILER POSI,
TCRFQP02J
L462E 23006011 FERRITE SHEET, SPOILER NEGA,
TCRFQN03J
L661 23221129 CHOKE COIL, TRF9240AC (15CSZ2R)
L840 23289918 COIL, PEAKING COIL 10MMH, TRF4100AU
L864 23103249 CORE, FERRITE BEAD 3.5X4.5, TEM2011AO
L883 23103248 FERRITR CHOKE, TEM2014AA
L884 23248230 COIL, CHOKE, TLN3142AC (15SZ2E/15SZ2H)
L884 23103279 FILTER, FERRITR CHOKE 3.5X5X2,
TEM2014AO (15CSZ2R)
*L901 23200574 COIL, DG-0.45, TSB-2424AL
LA03 23103248 FERRITR CHOKE, TEM2014AA
LA04 23103279 FILTER, FERRITR CHOKE 3.5X5X2,
TEM2014AO (15CSZ2R)
LA05 23289918 COIL, PEAKING COIL 10MMH, TRF4100AU
LC01 23238513 COIL, PEAKING, TRF4R22AJ
(15SZ2E/15CSZ2R)
LC04 23289918 COIL, PEAKING COIL 10MMH, TRF4100AU
(15CSZ2R)
LZ02 23221129 CHOKE COIL, TRF9240AC (15CSZ2R)
T401 23224983 TRANSFORMER, HORIZONTAL DRIVE,
TLN1039
*T461 23236806 TRANSFORMER, FLY-BACK, TFB4125HY
T801 23211761 COIL, LINE FILTER, TRF3148BF
*T862 23217635 TRANSFORMER, TPW3532AM
SEMICONDUCTORS
Q100 23009669 IC, P/N 2IN1 VCD MICRO, A8801CPCN4UD7
(15SZ2E/15SZ2H)
Q100 23009668 IC, P/N 2IN1 VCD MICRO, A8801CPCN4V63
(15CSZ2R)
Q101 23114611 TRANSISTOR, 2SC3357
Q103 23205006 TRANSISTOR, KTA2014Y-RTK
Q104 23205006 TRANSISTOR, KTA2014Y-RTK
Q108 70200984 IC, A/V SW 3IN1X1 SOP-8C, MM1113XF
Q109 23314962 TRANSISTOR, KTA1266 Y
Q112 23205006 TRANSISTOR, KTA2014Y-RTK
Q115 23205006 TRANSISTOR, KTA2014Y-RTK
Q116 23205005 TRANSISTOR, KTA2014Y-RTK
Q130 70114396 TRANSISTOR, 2SC3326B
Q196 23314965 TRANSISTOR, KTC3198 Y
Q301 23009352 IC, AN5522
Q301B 72471081 SCREW, 3X8MM
Q402 23114755 TRANSISTOR, 2SC2482FA-1
Q404 23314969 TRANSISTOR, 2SD2499(FA)
Q404B 72471082 SCREW, 3X10MM
Q421 23314141 TRANSISTOR, 2SC3852
Q422 23009188 IC, KIA7805API
Q422B 70391355 SCREW, BIND HEAD TAP-TITE B,
BITTB 3X8 SZN
Q430 23314980 TRANSISTOR, 2SD2549 P
Q431 23205148 TRANSISTOR, DTC123JKAT146
Q610 23904650 IC, TDA1013B
Q610B 70391355 SCREW, BIND HEAD TAP-TITE B,
BITTB 3X8 SZN
Q801 23009243 IC, POW SW.REG.IC VDS=650V,
PO= STR-W5753A
Q801B 70391355 SCREW, BIND HEAD TAP-TITE B,
BITTB 3X8 SZN
Q819 23205006 TRANSISTOR, KTA2014Y-RTK
Q840 23114733 TRANSISTOR, 2SC2655-Y
*Q862 23906937 IC, PHOTO COUPLER, ON3171-R
Q880 23205148 TRANSISTOR, DTC123JKAT146
Q901 23114756 TRANSISTOR, 2SC2482
Q903 23114756 TRANSISTOR, 2SC2482
Q905 23114756 TRANSISTOR, 2SC2482
Q907 23205005 TRANSISTOR, KTA2014Y-RTK
Q908 23114429 TRANSISTOR, 2SC2120-Y(TE
QA02 23906923 IC, CAT24WC08P
QA51 23205006 TRANSISTOR, KTA2014Y-RTK
QA52 23205005 TRANSISTOR, KTA2014Y-RTK
QA53 23205005 TRANSISTOR, KTA2014Y-RTK
QA60 23205006 TRANSISTOR, KTA2014Y-RTK
QB30 23205006 TRANSISTOR, KTA2014Y-RTK
QB43 23205148 TRANSISTOR, DTC123JKAT146
QB60 23205006 TRANSISTOR, KTA2014Y-RTK
QB61 23205006 TRANSISTOR, KTA2014Y-RTK
QV10 23314962 TRANSISTOR, KTA1266 Y
QV13 23000359 IC, MM1111XF
D101 23316411 DIODE, ZENER, HZT33-12
D150 23316231 DIODE, 1SS355
D224 23316231 DIODE, 1SS355
D301 23357372 DIODE, AXIAL, EU2JGF-41U2
D302 23357372 DIODE, AXIAL, EU2JGF-41U2
D303 23316794 DIODE, SC570A
D406 23357372 DIODE, AXIAL, EU2JGF-41U2
D408 23357372 DIODE, AXIAL, EU2JGF-41U2
D421 23118622 DIODE, ZENER, RD10ES B2
D431 23118622 DIODE, ZENER, RD10ES B2
D432 23316231 DIODE, 1SS355
D440 23316254 DIODE, ERC06-15
D441 23118516 DIODE, ZENER, RD9.1ES B3
D444 23118338 DIODE, RU4AM LF-K2
D472 23316231 DIODE, 1SS355
D801 23316796 DIODE, VRRM=600V IF=1A DO-41,
ERB12-06E
D802 23316796 DIODE, VRRM=600V IF=1A DO-41,
ERB12-06E
D803 23316796 DIODE, VRRM=600V IF=1A DO-41,
ERB12-06E
D804 23316796 DIODE, VRRM=600V IF=1A DO-41,
ERB12-06E
D818 23118507 DIODE, ZENER, RD13ESA B3