Toshiba 29CZ8URB User manual

SERVICE MANUAL
Color Television
FILE NO. 060-200563GR
Published in Singapore, October 2005 GREEN© TOSHIBA SINGAPORE PTE LTD
Color Television
S5SS series
29CZ8URB
29CZ8URS
The above models are classified as green products (*1), as indicated by the underlined serial numbers. This Service
Manual describes replacement parts for the green products. When repairing these green product (s), use the part (s)
described in this manual and lead-free solder (*2).
For (*1) and (*2), see the next page.

– 2 –
TABLE OF CONTENTS
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS ............................................................................................................................................. 3
SET-UP ADJUSTMENT ................................................................................................................................................. 4
SERVICE MODE ........................................................................................................................................................... 6
DESIGN MODE ............................................................................................................................................................. 8
ELECTRICAL ADJUSTMENTS ..................................................................................................................................... 9
CIRCUIT CHECK ......................................................................................................................................................... 14
CHAPTER 2 SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA ................................................................................................................................... 15
LOCATION OF CONTROLS ........................................................................................................................................ 16
PROGRAMMING CHANNEL MEMORY ...................................................................................................................... 17
CHASSIS AND CABINET REPLACEMENT PARTS LIST ........................................................................................... 19
PC BOARDS TOP & BOTTOM VIEW .......................................................................................................................... 30
TERMINAL VIEW OF TRANSISTORS ........................................................................................................................ 38
CIRCUIT BLOCK DIAGRAM ....................................................................................................................................... 40
SPECIFICATIONS .................................................................................................................................................... END
APPENDIX:
CIRCUIT DIAGRAM
(*2)
LEAD-FREE SOLDER
This product is manufactured using lead-free solder as a part of a movement within the consumer products industry at large
to be environmentally responsible. Lead-free solder must be used in the servicing and repair of this product.
WARNING
This product is manufactured using lead free solder.
DO NOT USE LEAD BASED SOLDER TO REPAIR THIS PRODUCT!
The melting temperature of lead-free solder is higher than that of leaded solder by 86˚F to 104˚F (30˚C to 40˚C). Use of a
soldering iron designed for lead-based solders to repair product made with lead-free solder may result in damage to the
component and or PCB being soldered. Great care should be made to ensure high-quality soldering when servicing this
product -especially when soldering large components, through-hole pins, and on PCBs - as the level of heat required to
melt lead-free solder is high.
(*1)
GREEN PRODUCT PROCUREMENT
The EC is actively promoting the WEEE & RoHS Directives that define standards for recycling and reuse of Waste Electri-
cal and Electronic Equipment and for the Restriction of the use of certain Hazardous Substances. From July 1, 2006, the
RoHS Directive will prohibit any marketing of new products containing the restricted substances.
Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental
protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its
environmental activities. In line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase and
use products, parts and materials that have low environmental impacts.
Green procurement of parts is not only confined to manufacture. The same green parts used in manufacture must also be
used as replacement parts.

GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
–3 –
2. The only source of X-RAY RADIATION in this TV receiver
is the picture tube. For continued X-RAY RADIATION
protection, the replacement tube must be exactly the same
type tube as specified in the parts list.
3. Some part in this receiver have special safety-related
characteristics for X-RAY RADIATION protection. For
continued safety, parts replacement should be undertaken
only after referring to the PRODUCT SAFETY NOTICE
below.
SAFETY PRECAUTION
WARNING : Service should not be attempted by anyone unfamiliar with the necessary precautions on this receiver.The following
are the necessary precautions to be observed before servicing this chassis.
1. An isolation transformer should be connected in the power line between the receiver and the AC line before any service is
performed on the receiver.
2. Always discharge the picture tube anode to the CRT conductive coating before handling the picture tube. The picture tube
is highly evacuated and if broken, glass fragments will be violently expelled. Use shatter proof goggles and keep picture
tube away from the unprotected body while handling.
3. When replacing a chassis in the cabinet, always be certain that all the protective devices are put back in place, such as;
nonmetallic control knobs, insulating covers, shields, isolation resistor-capacitor network etc.
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION”AND “PRODUCT SAFETY NOTICE”INSTRUCTIONS BELOW.
X-RAY RADIATION PRECAUTION
1. Excessive high voltage can produce potentially hazardous
X-RAY RADIATION. To avoid such hazards, the high
voltage must not be above the specified limit.The nominal
value of the high voltage of this receiver is (A) kV at zero
beam current (minimum brightness) under a (C) V AC
power source. The high voltage must not, under any
circumstances, exceed (B) kV.
Refer to table-1 for high voltage (A), (B) & AC voltage (C).
(See SETTING & ADJUSTING DATA on page 15)
Each time a receiver requires servicing, the high voltage
should be checked following the HIGH VOLTAGE CHECK
procedure in this manual. It is recommended that the
reading of the high voltage be recorded as a part of the
service record. It is important to use an accurate and
reliable high voltage meter.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are
often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using
replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety char-
acteristics are identified in this manual and its supplements; electrical components having such features are identified by the
international hazard symbols on the schematic diagram and the parts list.
Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement
parts which do not have the same safety characteristics as specified in the parts list may create shock, fire, X-ray radiation
or other hazards.

GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
–4 –
SET-UP ADJUSTMENT
RThe following adjustments should be made when a complete realignment is required or a new picture tube is installed.
Perform the adjustments in order as follows :
1. Color Purity
2. Convergence
3. White Balance
Note: The PURITY/CONVERGENCE MAGNET assembly and rubber wedges need mechanical positioning.
Refer to figure 1.
Mounting position of the purity magnet assembly should fit to same position as old one because slightly difference to
the position depend on a kind of tube.
COLOR PURITY ADJUSTMENT
(1) Let the screen face in the installing direction or toward the east (when it is to be moved), bring up the service mode screen
after demagnetizing (front, left, right, and top) with the degaussing coil, receive white signals by pressing the abutton, and
then the receiver should be operated for more than 40 munutes.
(2) Perform rough adjustment of the central convergence with the P/C magnet according to the adjustment item.
(3) Receive built-in green signals, loosen set screws on the deflection yoke, remove rubber wedges, and shift the deflection
yoke to toward front.
(4) Move alternately the two 2-pole magnets of the P/C magnets so that the green raster can come to the center of the screen.
(5) Receive built-in red and blue signals, check that there is no inclination of the single color raster toward one side, and if each
color tilts to a great extent, make adjustment with the 2-pole magnet so that the 3 colors will come to the center evenly.
(6) Receive the green raster, shift the deflection yoke from
a foremost position (hitting against the picture tube) to
a backward position horizontally, stop the deflection
yoke at a position where it begins to become a green
raster, and perform accurate marking on the picture
tube.
(7) Shift the deflection yoke further backward, and perform
accurate marking at a position where the green raster
begins to being luck.
(8) Fix the deflection yoke at a position 60% forward within
the range marked in items (6) and (7) above.
CONVERGENCE ADJUSTMENTS
*Adjust the convergence magnet to get vest convergence in the order to (1) ~ (5).
R CENTER CONVERGENCE:
(1) Receive the white crosshatch or dot pattern from the service signal generator.
(2) Use the 2 pieces of main 4-pole magnets of P/C magnets, change the open angle, and align the red and blue vertical lines
on the screen center.
(3) Freeze the open angle of the main 4-pole magnets, turn them simultaneously, and align the horizontal lines.
(4) Take the same steps for items (2) and (3) above and align red/blue with green on the screen center using two 6-pole
magnets.
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION”AND “PRODUCT SAFETY NOTICE”ON PAGE 3 OF THIS MANUAL.
Figure 1.
A
P/C magnet installing position A
MAG-1108 : 37 mm
MAG-1113 : 39 mm
Green Belt
2-pole purity magnet
(27": Magnet is fixed with deflection yoke.)
6-pole convergence magnet
Sub-4-pole convergence magnet
Main 4-pole convergence magnet
Fix the deflection yoke at a position 60% forward from a
point between (6) and (7)
Picture tube
Shift deflection yoke
(6)
(8)
(7) Perform marking of each point
on the tape of picture tube
CRT-D board
P/C Mag
100 60 0%

GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
–5 –
(5) Adjust the sub-4-pole magnets only in case there is any deviation of Xv bow-shaped convergence. (To be usually set at the
initial position)
Align both sides with the sub-4-pole magnets and minimize the deviation of blue and red with the main 4-pole magnets.
R CIRCUMFERENCE CONVERGENCE ADJUSTMENT
*Perform correction in the following manner.
blue
blue
red
red
Main 4-pole magnet
red/blue
red/blue
green
green
6-pole magnet
Xv bow-shaped deviation of convergence
blue
red
Sub-4-pole magnet
A
D
E
F
A
B
C
B
C
S
N
D
E
F
A
B
C
D
E
F
N
S
YV YHC
GH
GH
blue
green
red
•Adjust coils and minimize deviation
(The 27”unit has coils underneath it)
blue
green
red
(Parts code:23 948 274) TC-S
Blue color or blue mark
*Insert the correction piece between the
picture tube and the deflection yoke.
Bonded surface
blue
green
red
(Parts code:23 948 464)
Transparent
Bonded surface
Red green blue Red
green
blue
Adjust (YHC) and minimize the deviation of YH.
Red
green
blue Red green blue
Adjust (YV) and minimize the deviation of YV.
Red
blue
green
Red
blue
green
Red
blue
green
Red
blue
green
Red
blue
green
blue
red
green
Red
blue
green
blue
red
green
(Insertion position of correction
piece)
Perform correction by
inserting the correction
piece into the clearance of
terminal board coils of the
deflection yoke.
Note:
Perform insertion by
turning the metal side to
the terminal board side of
the deflection yoke.

–6 –
SERVICE MODE
1. ENTERING TO SERVICE MODE
1) Press obutton once on
Remote Control.
2. DISPLAYING THE ADJUSTMENT MENU
1) Press MENU button on TV.
3. KEY FUNCTION IN THE SERVICE MODE
The following key entry during display of adjustment menu provides special functions.
Screen adjustment mode ON/OFF: - / - - button (on Remote)
Test signal selection : a button (on Remote)
Selection of the adjustment items : CH s/t(on TV or Remote)
Change of the data value : ;+/–(on TV or Remote)
Adjustment menu mode ON/OFF : MENU button (on TV)
Initialization of the memory (QA02) : CALL + cs(on TV)
Reset the count of operating protect
circuit to “00”: CALL + ct(on TV)
“RCUT”selection : 1 button
“GCUT”selection : 2 button
“BCUT”selection : 3 button
“SCNT”selection : 4 button
“CLPI”selection : 5 button
“TNTC”selection : 6 button
“OPT0”selection : YELLOW button
Self diagnostic display ON/OFF : 9 button
CAUTION : Never try to perform initialization unless you have changed the memory IC.
2) Press obutton again to
keep pressing.
3) While pressing the obutton,
press MENU button on TV set.
Color thickness correction
note: Displayed differently as shown below, depending
on the setting of the receiving color system.
COLP (PAL)
COLC (NTSC)
COLS (SECAM)
S
(Service mode display)
Item
Data
or Sound Mute
Adjustment mode
Press
Press
Service mode
Item
Data
S

– 7 –
4. SELECTING THE ADJUSTING ITEMS
1) Every pressing of CH sbutton in the service mode changes the adjustment items in the order of table-2.
(tbutton for reverse order)
Refer to table-2 for preset data of adjustment mode.
(See SETTING & ADJUSTING DATA on page 15)
5. ADJUSTING THE DATA
1) Pressing of ;+/– button will change the value of data in the range from 00H to FFH. The variable range depends on
the adjusting item.
6. EXIT FROM SERVICE MODE
1) Press POWER button to turn off the TV once.
RINITIALIZATION OF MEMORY DATA OF QA02
After replacing QA02, the following initialization is required.
1. Enter the service mode, then select any register item.
2. Press and hold the CALL button on the Remote, then press the CH sbutton on the TV. The initialization of QA02 has
been completed.
3. Check the picture carefully. If necessary, adjust any adjustment item above.
Perform “Auto tune” on the owner’s manual.
CAUTION: Never attempt to initialize the data unless QA02 has been replaced.
7. TEST SIGNAL SELECTION
1) Every pressing of abutton on the Remote Control changes the built-in test patterns on screen as described below in
SERVICE MODE.
• All White
Signals Picture
Signal off ALL White
8. SELF CHECK FUNCTION
1) Press “9”button on Remote Control during display of adjustment menu in the service mode.
The diagnosis will begin to check if interface among IC’s are executed properly.
2) During diagnosis, the following displays are shown.
1Part number of microprocessor (QA01)
2Operation number of protecting circuit ----“000”is normal.
3RF signal center frequency is locked.
4Version information of microprocessor
23 * * * * * *
POWER : 000
SYNC : OK
MAIN : V057
<SELF CHECK>
1
2
3
4

– 8 –
DESIGN MODE
2) While pressing CALL button on Remote
and press MENU button on TV.
3) Press MENU button on TV.
RCUT
20
S D Press
(Design mode)
Press
D
1. ENTERING TO DESIGN MODE
1) Select the Service mode.
(See page 6)
2. SELECTING THE ADJUSTING ITEMS
Every pressing of CH tbutton in the design mode changes the adjustment items in the order of table-3.
(sbutton for reverse order)
Refer to table-3 for data of design mode.
(See SETTING & ADJUSTING DATA on page 15)
3. ADJUSTING THE DATA
Pressing of ;-/+ button will change the value of data.

–9 –
ELECTRICAL ADJUSTMENTS
FOCUS VR ADJ
SUB-BRIGHTNESS
(BRTC)
Note: Constrict the picture height
until the vertical retrace line
appears adjusting the item
HIT (HEIGHT).
HORIZONTAL POSITION
ADJUSTMENT (HPOS)
VERTICAL POSITION
ADJUSTMENT (VPOS)
VERTICAL AMPLITUDE
ADJUSTMENT (HIT)
1. Enter the service mode, then select any register item.
2. Press the abutton on the Remote until the black cross-bar pattern appears on the
screen.
3. Adjust the FOCUS control (on T461) for well defined scanning lines on the picture
screen.
1. Set CONTRAST to minimum, and
BRIGHTNESS to center by adjusting user
controls.
2. Set the TV in service mode to get Black
cross-bar of inside pattern.
3. Select BRTC (brightness correction), and
adjust the ;–/+ button to reduce the value
so that white portion of inside pattern slightly
light.
4. Adjust ;–/+ button to increase the data
value of BRTC, and set it just before the
difference between the belt of vertical retrace
and the border of black portion of inside
pattern is visible.
After that, return vertical height and contrast.
1. Set the TV in service mode, and get
black cross-bar signal with abutton
on remote hand unit.
2. Select either HPOS (Horizontal picture
phase) or VPOS (Vertical picture
phase) with CH s, tbuttons, and
adjust horizontal or vertical picture
position in the center of screen with
;–/+ buttons.
1. Set the TV in service mode, and get
black cross-hatch signal with abutton
on remote hand unit.
2. Select HIT (Vertical amplitude) with
CH s, tbuttons, and adjust vertical
amplitude with ;–/+ buttons so that
vertical amplitude lacks a little.
3. Adjust vertical amplitude with ;–/+
buttons so that the first bar on cross-
hatch signal touches edge of screen.
Belt of vertical retrace
The first
ITEM ADJUSTMENT PROCEDURE

–10 –
WIDTH
(WID)
E-W PARABOLA
(PARA)
WHITE BALANCE
ADJUSTMENT
•CUTOFF ADJUSTMENT
(RCUT)
(GCUT)
(BCUT)
•DRIVE ADJUSTMENT
(GDRV)
(BDRV)
1. Call up the adjustment mode display, then select the item WID.
2. Press the ;–/+ button to get the picture so the left and rightedges of raster begins
to lack.
3. Press the ;–/+ button to advance the data by 7 steps.
Note: Check the horizontal picture position is correct.
1. Call up the adjustment mode display, then select the item PARA.
2. Press the abutton on Remote until the cross-hatch pattern appears on the screen.
3. Press the ;–/+ button to make vertical lines straight as shown below.
1. Set Contrast to 40, and brightness to +20 by picture control.
2. Receive the Black and White pattern.
3. Select RCUT, GCUT, BCUT, GDRV and BDRV with CH s, tbuttons. Press volume
;–/+ buttons to set individual values to initial reference data.
4. Press button on the remote control and rotate Screen VR to get one slight
horizontal line on screen.
Note: Every pressing of button provides Horizontal line picture and Normal
picture alternately.
5. Press button to release horizontal line picture, and select the two other colors
which did not light in the above step with CH s, tbuttons. Then tap ;–/+ buttons
so that three colors slightly light in the same level.
XTo correct white balance in light area,
select GDRV and BDRV with CH s, t
buttons to adjust.
XTo correct white balance in dark area,
perform fine adjustment of RCUT, GCUT
and BCUT.
ITEM ADJUSTMENT PROCEDURE
Light area check
(to show white)
Dark area check
(to show black)

–11 –
Cutoff adjustment and
white balance adjust-
ment
RCUT
GCUT
BCUT
GDRV
BDRV
Screen VR
Sub brightness adjus-
tment
(BRTC)
1) Setting to horizontal alignment, turn the screen VR to
stop where the brightness lines are slightly luminous.
(Adjustment shall be made so that they look almost
white.)
2) Cancel horizontal alignment.
3) Varying R, G and B CUTOFF, make white balance
adjustment in the dark area.
4) Adjusting G and B DRIVE, make white balance
adjustment in the bright area.
5) Repeat procedures 3) and 4) if necessary.
Adjustable value:
Bright area: 11500K+0.0075uV
(103cd/m2)
Dark area: 10500K+0.0105uV
(17cd/m2)
1) Select BRTC in the sub data adjustment mode.
Adjust the number of black solid lines to 4±1.5.
No. ADJUSTMENT PROCEDURE
V/C syatem adjustment
ADJUSTING ITEMS
AND POINTS REMARKS
1
2
No outside lighting shall
be allowed.
Measurement shall be
performed at the center of
CRT.
Receiver shall be in the
standard state.
Total white signal Varying
the level of input signal,
adjust the brightness.
J-2ch sub brightness
signal DYNAMIC
Focus Adjustment
Main Focus: T461
Conditions : PAL RETMA ch
Screen Size : Wide
Presentation Mode : Dynamic
Only for 29-inch model
1) Adjust the Main Focus VR knob of T461 model to optimize center focus.
Refer to the diagram below for the location of the Main Focus VR knob.
No. ADJUSTMENT PROCEDURE
Circuit adjustment (Procedure Manual for Deflection Adjustment)
ADJUSTING ITEMS
AND POINTS
1
Main Focus VR knob
SCREEN knob

–12 –
For PAL/100 Hz/WIDE
Horizontal amplitude
(WID)
Side pin distortion
(PARA)
Trapezoidal distortion
(TRAP)
Corner distortion
(CNR)
Upper corner distortion
(TCNR)
Lower corner distortion
(BCNR)
CENT distortion
(CPAR)
Parallelogrammatic
distortion (CSAW)
Horizontal phase
(HPOS)
Note 1:
POW/DEF board: P451/
M450
Horizontal screen
positional switch
Screen position shall be
switched by inserting a
plug into the above pin.
(CENT should take the
first stage)
<Adjustment condition>
Horizontal adjustment shall be made using E-12CH Philips pattern and DYNAMIC
image mode.
<Adjustment procedure>
1) Using WID data, reduce the horizontal amplitude until a part of it is dropped out.
2) Using WID data, adjust the horizontal amplitude so that horizontal raster inevitably
contacts with CPT mask.
3) Using the following (Note 1) horizontal screen positional switch, adjust the horizontal
raster position to the center position.
4) Using the horizontal amplitude
(WID) and horizontal phase
(HPOS), adjust the horizontal
amplitude so that the right and left
flags are just blinded.
The adjustment shall be made so that the right and left flags are just blinded.
5) Using PARA, TRAP, CNR and CPAR (or TCNR, BCNR or CSAW if necessary),
adjust the screen distortion.
6) If necessary, make the horizontal amplitude adjustment again.
ADJUSTMENT PROCEDURE
Horizontal adjustment
ADJUSTING ITEMS
AND POINTS
Hori-
zontal
* Deflection adjustment shall be made from PAL/100 Hz/WIDE mode.
Right side Left side
CENT
30
30
2
0
35
25
30
30
2
0
35
25
30
30
2
0
35
25
30
30
2
0
35
25
30
30
20
35
45
325
525 LINE
50
1
3
5
1
3
5
575 300
5
31
5
31
For NTSC WIDE
Horizontal phase
(NHPO)
Horizontal amplitude
(NWID)
Side pin distortion
(NPAR)
Trapezoidal distortion
(NTRA)
Corner distortion
(NCNR)
CENT distortion
(NCPAR)
Parallelogrammatic
distortion (NCSAW)
Upper corner distortion
* NTSC adjustment shall be made after PAL adjustment.
1) With domestic 13ch, WIDE
mode and DYNAMIC, adjust
the right and left bars to the
fifth center for horizontal phase
(NHPO) and horizontal
amplitude (NWID).
Right and left bars shall be adjusted
to the fifth center.
2) With domestic 11ch, NPAR, NTRA, NCNR and NCPAR (or NTCNR, NBCNR or
NCSAW if necessary), adjust the screen distortion.
3) If necessary, make horizontal amplitude adjustment again.
ADJUSTMENT PROCEDURE
Horizontal adjustment
ADJUSTING ITEMS
AND POINTS
Hori-
zontal

–13 –
For PAL WIDE
Vertical amplitude
(HIT)
Vertical screen position
(TCNR)
Vertical linearity
(VLIN)
For NTSC WIDE
Vertical amplitude
(NHIT)
Vertical screen position
(NVPO)
1) With E-12ch, WIDE mode, DYNAMIC and 100 Hz, adjust the vertical screen
position (VPOS) and amplitude (HIT) as shown in the following figure:
2) With vertical linearity (VLIN), control the upper and lower balances to be optimal.
* NTSC adjustment shall be made after the PAL adjustment.
With domestic 13ch, WIDE mode and DYNAMIC, adjust the vertical screen position
(NVPO) and amplitude (NHIT) as shown in the following figure:
ADJUSTMENT PROCEDURE
Vertical adjustment
ADJUSTING ITEMS
AND POINTS
Verti-
cal
Flags shall just be blinded.
Flags shall just be blinded.
30
30
2
0
35
25
30
30
2
0
35
25
30
30
2
0
35
25
30
30
2
0
35
25
30
30
20
35
45
325
525 LINE
50
1
3
5
1
3
5
575 300
5
31
5
31
The circle of lion shall contact
with mask.
The twelve center shall be adjusted to the mask.
Conditions: User control for geomagnetic compensation: 0
Geomagnetic compensation coil: Unconnected
Perform voltage measurement at both ends of RJ06 and adjust the volt-
age to the following adjustable value with GMF of data adjustment mode:
0 ± 1V
ADJUSTMENT PROCEDURE
Geomagnetic compensation (chassis adjustment)
ADJUSTING ITEMS
AND POINTS
1 Output voltage control
(GMF)

–14 –
CIRCUIT CHECK
HIGH VOLTAGE CHECK
CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps below.
1. Connect an accurate high voltage meter to the second anode of the picture tube.
2. Turn on the receiver. Set the BRIGHTNESS and CONTRAST controls to minimum (zero beam current).
3. High voltage must be measured below (B) kV.
Refer to table-1 for high voltage (B).
(See SETTING & ADJUSTING DATA on page 15)
4. Vary the BRIGHTNESS control to both extremes to be sure the high voltage does not exceed the limit under any conditions.

– 15 –
CHAPTER 2 SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA
SAFETY INSTRUCTIONS
SERVICE MODE
ADJUSTING ITEMS AND DATAS IN THE SERVICE MODE:
Table-1
Table-2
DESIGN MODE
ADJUSTING ITEMS AND DATAS IN THE DESIGN MODE:
29"
HIGH VOLTAGE AT ZERO BEAM: (A) 30.5 kV
MAX HIGH VOLTAGE: (B) 34.0 kV
AC VOLTAGE (C) 220~240 V
RCUT R CUTOFF 20H ←
GCUT G CUTOFF 20H ←
BCUT B CUTOFF 20H ←
GDRV G DRIVE 40H ←
BDRV B DRIVE 40H ←
BRTC BRIGHTNESS CENTER C0H ←
BRTR BRIGHTNESS RGB 3FH ←
BRTO BRIGHTNESS OSD 00H ←
CNTC CONTRAST CENTER 3FH ←
SCNT SUB CONTRAST (TV) 08H ←
SCNV SUB CONTRAST (VIDEO) 0AH ←
CNTR CONTRAST RGB 63H ←
CNTO CONTRAST OSD 03H ←
COLC COLOR CEN NTSC 57H ←
COLP COLOR CEN PAL 57H ←
COLS COLOR CEN SECAM 49H ←
TNTCN TINT CENTER NTSC 47H ←
TNTCP TINT CENTER PAL 3FH ←
HPOS 576i 100Hz 3AH 41H
VPOS V-POSITION 83H 94H
HIT HEIGHT 6BH 41H
VLIN V-LINEARITY 0FH 0CH
VPS V-SHIFT 3EH ←
Item Name of adjustment Data Preset
WID PICTURE WIDTH 50H 5CH
PARA E-W PARABOLA 1BH 31H
CNR E-W CORNER 11H ←
TRAP TRAPEZIUM 2FH 4CH
CPAR CENT PARABOLA 07H ←
TCNR EW TOP CORNER 0AH 17H
BCNR EW BOTTOM CORNER 11H 15H
CSAW CENTER SAW 09H 07H
NHPO NTSC H-POSITION 03H ←
SCNT NTSC V-POSITION 04H 98H
NHIT NTSC HIGHT 00H 37H
NVLI NTSC V-LINEARITY 00H 0DH
NVPS NTSC V-SHIFT 3EH ←
NWID NTSC PICTURE WIDTH 03H 52H
NPAR NTSC E-W PARABOLA 01H 29H
NCNR NTSC E-W CORNER 00H ←
NTRA NTSC TRAPEZIUM 00H 4CH
NCPAR NTSC CENT PARABOLA 00H 08H
NTCNR NTSC TOP CORNER 00H 15H
NBCNR NTSC BOTTOM CORNER 00H 13H
NCSAW NTSC CENTER SAW FFH 07H
GMF Geomagnetic 00H 04H
Item Name of adjustment Data Preset
Item Name of adjustment Reset
OPT0 OPTION 0 07H
OPT1 OPTION 1 10H
OPT2 OPTION 2 03H
Table-3

– 16 –
NAMES AND FUNCTIONS OF CONTROLS
TV Front and Remote control
Note: The shaded button is not available for 29CZ8URS. If you press the button, “MODE NOT AVAILABLE” will appear on the
screen.

– 17 –
To use the SEARCH function
1Press MENU and then < / > to highlight the “
SET UP
CH
????
SET
UP” icon.
ASM OK
SKIP OFF
SEARCH [
< ] [ > ]
POSITION P01
MEMORY OK
MFT [
< ] [ > ]
AFT ON
SET UP
FUNC.
AUDIO
PICTURE
TIMER
F
CH
????
SELECT ADJUST
2Press / to select “SEARCH”. Press < / > to start
searching. Pressing “<” searches for channels at lower
frequencies while pressing “>” searches for channels
at higher frequencies. While searching, pressing the
opposite direction button, > and < respectively, will
cancel SEARCH function.
( )
SEARCH VHF L P01
STOP
ASM OK
SKIP OFF
SEARCH [
< ] [ > ]
POSITION P01
MEMORY OK
MFT [
< ] [ > ]
AFT ON
SET UP
FUNC.
AUDIO
PICTURE
TIMER
F
CH
????
SELECT ADJUST
Repeat this process until you can get the desired
channel.
3When the desired channel is shown, press to select
“POSITION”. Press < / > repeatedly until the position
number to be preset is shown.
ASM OK
SKIP OFF
SEARCH [
< ] [ > ]
POSITION P02
MEMORY OK
MFT [
< ] [ > ]
AFT ON
SET UP
FUNC.
AUDIO
PICTURE
TIMER
F
CH
????
SELECT ADJUST
4Press to select “MEMORY”, then press OK to
memorize the channel at the current position.
ASM OK
SKIP OFF
SEARCH [
< ] [ > ]
POSITION P02
MEMORY OK
MFT [
< ] [ > ]
AFT ON
SET UP
FUNC.
AUDIO
PICTURE
TIMER
F
CH
????
SELECT ADJUST
5When you program other channels, repeat steps 2 to
4.
Preset the channels automatically
(ASM function)
Use remote control for this operation. The buttons on the TV
with similar name may also be use.
1Select the starting position for channel to be preset.
Press the Number buttons (-/--, 0~9) or CH s/t.
1
2Set the correct broadcast system for your region.
Press MENU and then < / > to highlight the “
SET UP
CH
????
SET
UP” icon.
OK
MENU
SET UP
FUNC.
AUDIO
PICTURE
TIMER
F
CH
????
SELECT ADJUST
SOUND SYSTEM B/G
COLOR SYSTEM AUTO
MTS AUTO
Press to scroll down the menu (second page) to
confirm “COLOR SYSTEM” is set to “AUTO” and
“SOUND SYSTEM” is set to proper system. If not,
press / to select “COLOR SYSTEM” or “SOUND
SYSTEM” and press < / > to set each proper system.
3Press / to select “ASM”, then press OK to start
the search. When the TV screen returns to the start
position, the procedure is complete.
OK
ASM OK
SKIP OFF
SEARCH [
< ] [ > ]
POSITION P01
MEMORY OK
MFT [
< ] [ > ]
AFT ON
SET UP
FUNC.
AUDIO
PICTURE
TIMER
F
CH
????
SELECT ADJUST
PROGRAMMING CHANNEL MEMORY

–18 –
Auto fine tuning (AFT)
If the signal frequency is unstable due to environmental
conditions, use auto fine tuning.
1Select the position number where the channel you
want to fine-tune with CH s/tor the digit selection
and number buttons (-/--, 0~9).
Note
When the position is set to “AFT OFF”status, the “R”
mark appears to the left of the position number.
25
When the channel is set to “AFT ON”status,the
position number is displayed without the “R”mark.
2Press MENU then < / > to highlight the “
SET UP
CH
????
SET UP”
icon.
3Press / to select “AFT”. Press < / > to select the
“ON”indication.
ASM OK
SKIP OFF
SEARCH [
< ] [ > ]
POSITION P25
MEMORY OK
MFT [
< ] [ > ]
AFT ON
SET UP
FUNC.
AUDIO
PICTURE
TIMER
F
CH
????
SELECT ADJUST
Notes
•When you operate MFT, AFT is switched “OFF”
automatically. If you switch on AFT after fine tuning with
MFT, MFT may be canceled.
•AFT may be set independently for each position.
To skip a position number
After presetting the channels, you may skip unnecessary
position numbers so that only the channels you want to watch
are selected using CH s/t.
1First, select the position number to be skipped with
CH s/tor digit selection and number buttons (-/--,
0~9).
2Highlight the “
SET UP
CH
????
SET UP”icon and press / to
select “SKIP”.
ASM OK
SKIP OFF
SEARCH [
< ] [ > ]
POSITION P12
MEMORY OK
MFT [
< ] [ > ]
AFT ON
SET UP
FUNC.
AUDIO
PICTURE
TIMER
F
CH
????
SELECT ADJUST
3Press < / > to set “SKIP”to “ON”. This completes the
setting for skipping the selected position number.
Notes
•When “SKIP”is set to “ON”for the selected position
number, a “* ”mark appears to the left of the position
number.
The position number will then be skipped when you select
the position with the CH s/tbuttons.
•If you want to restore a skipped position number, select it
using the -/-- and 0~9 buttons then switch the “SKIP”setting
to “OFF”.
Manual fine tuning (MFT)
The adjustments below are not necessary under normal
conditions. However, under some reception conditions, fine
tuning may be necessary to improve the picture quality. In
such cases, adjust the manual fine tuning (MFT).
1Select the position number where the channel you
want to fine-tune with CH s/tor digit selection and
number buttons (-/--,0~9).
2Press MENU and then < / > to highlight the “
SET UP
CH
????
SET
UP”icon.
3Press / to select “MFT”. Press < / > to start fine
tuning. Press < / > repeatedly until the best possible
picture and sound are obtained.
ASM OK
SKIP OFF
SEARCH [
< ] [ > ]
POSITION P04
MEMORY OK
MFT [
< ] [ > ]
AFT ON
SET UP
FUNC.
AUDIO
PICTURE
TIMER
F
CH
????
SELECT ADJUST
12

– 19 –
CHASSIS AND CABINET REPLACEMENT PARTS LIST
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRE-
CAUTION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF THIS MANUAL.
CAUTION: The international hazard symbols “ ” in the schematic diagram and the parts list designate components
which have special characteristics important for safety and should be replaced only with types identical to those in the
original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals.
Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE. Do not degrade the safety
of the receiver through improper servicing.
NOTICE:
•The part number must be used when ordering parts, in order to assist in processing, be sure to include the
Model number and Description.
•The PC board assembly with *mark is no longer available after the end of the production.
Model: 29CZ8URB/29CZ8URS
Capacitors .......... CD : Ceramic Disk PF : Plastic Film EL : Electrolytic
Resistors ............ CF : Carbon Film CC : Carbon Composition MF : Metal Film
OMF : Oxide Metal Film VR : Variable Resistor FR : Fusible Resistor
(All CD and PF capacitors are ±5%, 50V and all resistors, ±5%, 1/6W unless otherwise noted.)
Location Parts No. Description
No.
#1: [29CZ8URB]
#2: [29CZ8URS]
CAPACITORS
C101 76206479 ELECTROLYTIC 50V 4.7UF M 7L 3A
C102 76109102 CERAMIC CHIP 50V B 1000PF K
C103 76203101 ELECTROLYTIC 16V 100UF M 7L 3A
C104 76109103 CERAMIC CHIP 50V B 0.01UF K
C302 76764221 ELECTROLYTIC 25V 220UF M
C304 76214471 CERAMIC DISC 500V B 470PF K
C305 76214471 CERAMIC DISC 500V B 470PF K
C306 76667102 ELECTROLYTIC 25V 1000UF M
C308 76503053 PLASTIC FILM 63V 1UF J
C310 76667102 ELECTROLYTIC 25V 1000UF M
C311 76109471 CERAMIC CHIP 50V B 470PF K
C312 76073036 ELECTROLYTIC 16V 33UF M 3A
C313 76669101 ELECTROLYTIC 50V 100UF M
C314 76764221 ELECTROLYTIC 25V 220UF M
C315 76082256 PLASTIC FILM 100V 2200PF J
C333 76082272 PLASTIC FILM 100V 0.047UF J
C366 76082057 PLASTIC FILM 100V 0.22UF J
C401 76591473 PLASTIC FILM 50V 0.047UF J
C403 76679220 ELECTROLYTIC 250V 22UF M 3A
C413 76214392 CERAMIC DISC 500V B 3900PF K
C416 76678330 ELECTROLYTIC 200V 33UF M 3A
C417 76214391 CERAMIC DISC 500V B 390PF K
C418 76764221 ELECTROLYTIC 25V 220UF M
C434 76591104 PLASTIC FILM 50V 0.1UF J
C438 76764102 ELECTROLYTIC 25V 1000UF M
C441 76693472 PLASTIC FILM 100V 4700PF J
C442 76168057 PLASTIC FILM 540)400V 204J 4-20
C443 76503196 PLASTIC FILM 1800VH 5600PF H
C444 76503198 MT PLA T 1800VH 682H CF92T3Q682HA
C445 76829473 PLASTIC FILM 400V 0.047UF J
C446 76503124 PLASTIC FILM 400V 0.068UF J
C447 76679220 ELECTROLYTIC 250V 22UF M 3A
C448 76640908 ELECTROLYTIC 160V 33UF M 3A LI
C449 76214331 CERAMIC DISC 500V B 330PF K
C461 76168056 PLASTIC FILM 540)400V 184J 4-20
C462 76820123 PLASTIC FILM 630V 0.012UF J
C464 76503149 PLASTIC FILM 250V 3.3UF
C465 76214471 CERAMIC DISC 500V B 470PF K
C466 76214471 CERAMIC DISC 500V B 470PF K
C467 76820153 PLASTIC FILM 630V 0.015UF J
C470 76766220 ELECTROLYTIC 50V 22UF M
C472 76503049 PLASTIC FILM 63V 0.47UF J
C473 76206010 ELECTROLYTIC 50V 1.0UF M 7L 3A
C501 76092730 CERAMIC CHIP 16V B 0.1UF K
C502 76092730 CERAMIC CHIP 16V B 0.1UF K
C503 76092730 CERAMIC CHIP 16V B 0.1UF K
C504 76792101 ELECTROLYTIC 6.3V 100UF M
C505 76092730 CERAMIC CHIP 16V B 0.1UF K
C506 76206010 ELECTROLYTIC 50V 1.0UF M 7L 3A
C507 76100103 CERAMIC CHIP 50V F 0.01UF Z
C515 76092730 CERAMIC CHIP 16V B 0.1UF K
C520 76092730 CERAMIC CHIP 16V B 0.1UF K
C521 76092730 CERAMIC CHIP 16V B 0.1UF K
C522 76092730 CERAMIC CHIP 16V B 0.1UF K
C523 76092730 CERAMIC CHIP 16V B 0.1UF K
C524 76203101 ELECTROLYTIC 16V 100UF M 7L 3A
C525 76100103 CERAMIC CHIP 50V F 0.01UF Z
C526 76100103 CERAMIC CHIP 50V F 0.01UF Z
C527 76100103 CERAMIC CHIP 50V F 0.01UF Z
C530 76203220 ELECTROLYTIC 16V 22UF M
C531 76092730 CERAMIC CHIP 16V B 0.1UF K
C536 76203101 ELECTROLYTIC 16V 100UF M 7L 3A
C537 76092730 CERAMIC CHIP 16V B 0.1UF K
C560 76203101 ELECTROLYTIC 16V 100UF M 7L 3A
C562 76092730 CERAMIC CHIP 16V B 0.1UF K
C563 76092730 CERAMIC CHIP 16V B 0.1UF K
C564 76092730 CERAMIC CHIP 16V B 0.1UF K
C566 76100103 CERAMIC CHIP 50V F 0.01UF Z
C567 76100103 CERAMIC CHIP 50V F 0.01UF Z
C570 76092730 CERAMIC CHIP 16V B 0.1UF K
C571 76092730 CERAMIC CHIP 16V B 0.1UF K
C572 76092730 CERAMIC CHIP 16V B 0.1UF K
C573 76100103 CERAMIC CHIP 50V F 0.01UF Z
C574 76206478 ELECTROLYTIC 50V 0.47UF M 7L 3A
C575 76206010 ELECTROLYTIC 50V 1.0UF M 7L 3A
C576 76092730 CERAMIC CHIP 16V B 0.1UF K
C579 76206229 ELECTROLYTIC 50V 2.2UF M 7L 3A
C580 76206010 ELECTROLYTIC 50V 1.0UF M 7L 3A
C581 76206229 ELECTROLYTIC 50V 2.2UF M 7L 3A
C583 76100103 CERAMIC CHIP 50V F 0.01UF Z
C586 76092730 CERAMIC CHIP 16V B 0.1UF K
C588 76105471 CERAMIC CHIP 50V CH 470PF J
C624 76206478 ELECTROLYTIC 50V 0.47UF M 7L 3A
C660 76206010 ELECTROLYTIC 50V 1.0UF M 7L 3A
C662 76109102 CERAMIC CHIP 50V B 1000PF K
C663 76206229 ELECTROLYTIC 50V 2.2UF M 7L 3A
C664 76206010 ELECTROLYTIC 50V 1.0UF M 7L 3A
C666 76109102 CERAMIC CHIP 50V B 1000PF K
C667 76206229 ELECTROLYTIC 50V 2.2UF M 7L 3A
C669 76203470 ELECTROLYTIC 16V 47UF M 7L 3A
C671 76763471 ELECTROLYTIC 16V 470UF M
C672 76203470 ELECTROLYTIC 16V 47UF M 7L 3A
Location Parts No. Description
No.

–20 –
Location Parts No. Description
No.
Location Parts No. Description
No.
C681 76765471 ELECTROLYTIC 35V 470UF M
C682 76765102 ELECTROLYTIC 35V 1000UF M
C683 76765471 ELECTROLYTIC 35V 470UF M
C686 76092883 CERAMIC CHIP 50V B 0.1UF K
C687 76092883 CERAMIC CHIP 50V B 0.1UF K
C690 76766470 ELECTROLYTIC 50V 47UF M
C704 76591822 PLASTIC FILM 50V 8200PF J
C705 76232103 CERAMIC DISC 50V F 0.01UF Z
C707 76203470 ELECTROLYTIC 16V 47UF M 7L 3A
C712 76203470 ELECTROLYTIC 16V 47UF M 7L 3A
C713 76709100 ELECTROLYTIC 200V 10UF M
C714 76436101 CERAMIC DISC 50V SL 100PF J
C715 76214472 CERAMIC DISC 500V B 4700PF K
C716 76436101 CERAMIC DISC 50V SL 100PF J
C717 76214472 CERAMIC DISC 500V B 4700PF K
C718 76797470 ELECTROLYTIC 50V 47UF M
C719 76435560 CERAMIC DISC 500V SL 56PF J
C720 76709100 ELECTROLYTIC 200V 10UF M
C721 76797470 ELECTROLYTIC 50V 47UF M
C726 76212102 CERAMIC DISC 50V B 1000PF K
zC801 76503507 PLASTIC FILM AC275V 0.22UF K
zC802 76503507 PLASTIC FILM AC275V 0.22UF K
C805 76092281 CERAMIC DISC AC250V E 4700PF
C806 76092281 CERAMIC DISC AC250V E 4700PF
C807 76503049 PLASTIC FILM 63V 0.47UF J
C808 76765101 ELECTROLYTIC 35V 100UF M
C809 76503049 PLASTIC FILM 63V 0.47UF J
C810 76073107 ELECTROLYTIC 400V 820UF
zC811 76166021
CERA CAP E 250V 102 DE1E3KX102MB4BL01
zC812 76591104 PLASTIC FILM 50V 0.1UF J
zC813 76591104 PLASTIC FILM 50V 0.1UF J
zC814 76203101 ELECTROLYTIC 16V 100UF M 7L 3A
zC815 76166021
CERA CAP E 250V 102 DE1E3KX102MB4BL01
C816 76203470 ELECTROLYTIC 16V 47UF M 7L 3A
C817 76092339 CERAMIC DISC 2KV 330PF K
C818 76095931 PLASTIC FILM 1250VH 2200PF J
C819 76676220 ELECTROLYTIC 100V 22UF M 3A
C821 76214471 CERAMIC DISC 500V B 470PF K
C822 76763471 ELECTROLYTIC 16V 470UF M
C823 76214471 CERAMIC DISC 500V B 470PF K
C824 76591104 PLASTIC FILM 50V 0.1UF J
C825 76591104 PLASTIC FILM 50V 0.1UF J
C826 76591104 PLASTIC FILM 50V 0.1UF J
C827 76591104 PLASTIC FILM 50V 0.1UF J
C828 76591104 PLASTIC FILM 50V 0.1UF J
C829 76212271 CERAMIC DISC 50V B 270PF K
C830 76591104 PLASTIC FILM 50V 0.1UF J
C832 76591104 PLASTIC FILM 50V 0.1UF J
C833 76206229 ELECTROLYTIC 50V 2.2UF M 7L 3A
C834 76591104 PLASTIC FILM 50V 0.1UF J
C834A 23960136 ADHESIVE SILICONE TSE3843-W
C835 76591104 PLASTIC FILM 50V 0.1UF J
C836 76591104 PLASTIC FILM 50V 0.1UF J
C837 76591104 PLASTIC FILM 50V 0.1UF J
C838 76203101 ELECTROLYTIC 16V 100UF M 7L 3A
C839 76203101 ELECTROLYTIC 16V 100UF M 7L 3A
C841 76766101 ELECTROLYTIC 50V 100UF M
C842 76203100 ELECTORLYTIC 16V 10UF M 7L 3A
C843 76591104 PLASTIC FILM 50V 0.1UF J
C845 76763471 ELECTROLYTIC 16V 470UF M
C884 76086916 ELECTROLYTIC 160V 330UF M 3D
C885 76214471 CERAMIC DISC 500V B 470PF K
C887 76214471 CERAMIC DISC 500V B 470PF K
C889 76766222 ELECTROLYTIC 50V 2200UF M
C891 76764102 ELECTROLYTIC 25V 1000UF M
C893 76092337 CERAMIC DISC 2KV 220PF K
C894 76764102 ELECTROLYTIC 25V 1000UF M
C895 76797471 ELECTROLYTIC 50V 470UF M
C896 76214471 CERAMIC DISC 500V B 470PF K
C898 76591272 PLASTIC FILM 50V 2700PF J
C899 76214471 CERAMIC DISC 500V B 470PF K
C902 76092349 CERAMIC DISC 2KV R 2200PF K
C904 76436471 CERAMIC DISC 50V SL 470PF J
C905 76436391 CERAMIC DISC 50V SL 390PF J
C907 76436681 CERAMIC DISC 50V SL 680PF J
C909 76073120 ELECTROLYTIC 250V 33UF
C910 76206478 ELECTROLYTIC 50V 0.47UF M 7L 3A
C911 76203100 ELECTORLYTIC 16V 10UF M 7L 3A
C912 76073044 ELECTROLYTIC 16V 3300UF M 3A
C913 76794102 ELECTROLYTIC 16V 1000UF M
C914 76232103 CERAMIC DISC 50V F 0.01UF Z
C918 76591104 PLASTIC FILM 50V 0.1UF J
C919 76591104 PLASTIC FILM 50V 0.1UF J
C931 76214101 CERAMIC DISC 500V B 100PF K
CA01 76109103 CERAMIC CHIP 50V B 0.01UF K
CA02 76203100 ELECTORLYTIC 16V 10UF M 7L 3A
CA03 76109103 CERAMIC CHIP 50V B 0.01UF K
CA04 76203100 ELECTORLYTIC 16V 10UF M 7L 3A
CA05 76109103 CERAMIC CHIP 50V B 0.01UF K
CA06 76105101 CERAMIC CHIP 50V CH 100PF J
CA07 76105101 CERAMIC CHIP 50V CH 100PF J
CA13 76105270 CERAMIC CHIP 50V CH 27PF J
CA22 76105100 CERAMIC CHIP 50V CH 10PF D
CA23 76105100 CERAMIC CHIP 50V CH 10PF D
CA24 76105100 CERAMIC CHIP 50V CH 10PF D
CA25 76105100 CERAMIC CHIP 50V CH 10PF D
CA28 76105050 CERAMIC CHIP 50V CH 5PF C
CA29 76105050 CERAMIC CHIP 50V CH 5PF C
CA30 76105101 CERAMIC CHIP 50V CH 100PF J
CA31 76109103 CERAMIC CHIP 50V B 0.01UF K
CA32 76203100 ELECTORLYTIC 16V 10UF M 7L 3A
CA33 76109103 CERAMIC CHIP 50V B 0.01UF K
CA34 76105101 CERAMIC CHIP 50V CH 100PF J
CA37 76105101 CERAMIC CHIP 50V CH 100PF J
CA38 76105101 CERAMIC CHIP 50V CH 100PF J
CA52 76763331 ELECTROLYTIC 16V 330UF M
CA53 76105181 CERAMIC CHIP 50V CH 180PF J
CA54 76206010 ELECTROLYTIC 50V 1.0UF M 7L 3A
CA55 76105102 CERAMIC CHIP 25V CH 1000PF J
CA56 76109332 CERAMIC CHIP 50V B 3300PF K
CA57 76092730 CERAMIC CHIP 16V B 0.1UF K
CA59 76092730 CERAMIC CHIP 16V B 0.1UF K
CB01 76203470 ELECTROLYTIC 16V 47UF M 7L 3A
CB20 76212101 CERAMIC DISC 50V B 100PF K
CB21 76212221 CERAMIC DISC 50V B 220PF K
CB22 76591472 PLASTIC FILM 50V 4700PF J
CB23 76591103 PLASTIC FILM 50V 0.01UF J
CB23A 23965241 TAPE CC #12 10MM L30M
CC07 76109102 CERAMIC CHIP 50V B 1000PF K
CC08 76109102 CERAMIC CHIP 50V B 1000PF K
CC09 76109102 CERAMIC CHIP 50V B 1000PF K
CC10 76109102 CERAMIC CHIP 50V B 1000PF K
CC14 76109103 CERAMIC CHIP 50V B 0.01UF K
CC20 76011224 CHIP 1/20W 220K OHM J
CC25 76109102 CERAMIC CHIP 50V B 1000PF K
CC26 76109102 CERAMIC CHIP 50V B 1000PF K
CC32 76109103 CERAMIC CHIP 50V B 0.01UF K
CC33 76109103 CERAMIC CHIP 50V B 0.01UF K
CD01 76203100 ELECTORLYTIC 16V 10UF M 7L 3A
CD02 76203100 ELECTORLYTIC 16V 10UF M 7L 3A
CD03 76109152 CERAMIC CHIP 50V B 1500PF K
CD04 76105471 CERAMIC CHIP 50V CH 470PF J
CD05 76203100 ELECTORLYTIC 16V 10UF M 7L 3A
CD06 76092730 CERAMIC CHIP 16V B 0.1UF K
CD07 76206339 ELECTROLYTIC 50V 3.3UF M 7L 3A
CD08 76203100 ELECTORLYTIC 16V 10UF M 7L 3A
CD09 76085944 ELECTROLYTIC NP 50V 2.2UF M 11L
CD10 76085944 ELECTROLYTIC NP 50V 2.2UF M 11L
CD12 76105560 CERAMIC CHIP 50V CH 56PF J
CD13 76109152 CERAMIC CHIP 50V B 1500PF K
CD14 76105471 CERAMIC CHIP 50V CH 470PF J
CD15 76203100 ELECTORLYTIC 16V 10UF M 7L 3A
CD17 76109152 CERAMIC CHIP 50V B 1500PF K
CD18 76105471 CERAMIC CHIP 50V CH 470PF J
CD19 76105221 CERAMIC CHIP 50V CH 220PF J
CD21 76105220 CERAMIC CHIP 50V CH 22PF J
CD22 76105220 CERAMIC CHIP 50V CH 22PF J
CD23 76092730 CERAMIC CHIP 16V B 0.1UF K
CD24 76206100 ELECTROLYTIC 50V 10UF M
CD26 76105560 CERAMIC CHIP 50V CH 56PF J
CD27 76105560 CERAMIC CHIP 50V CH 56PF J
CD28 76109102 CERAMIC CHIP 50V B 1000PF K
CD29 76109102 CERAMIC CHIP 50V B 1000PF K
CD30 76109102 CERAMIC CHIP 50V B 1000PF K
CD31 76109102 CERAMIC CHIP 50V B 1000PF K
CD32 76109222 CERAMIC CHIP 50V B 2200PF K