Toshiba 29SH9UH User manual

SERVICE MANUAL
Color Television
29SH9UH
34SH9UH
F2DS Chassis
FILE NO. 010-200317
Jan., 2004

– 2 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
TABLE OF CONTENTS
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS ........................................................................................................................................ 3
SET-UP ADJUSTMENT ............................................................................................................................................ 4
SERVICE MODE ...................................................................................................................................................... 6
DESIGN MODE ........................................................................................................................................................ 9
ELECTRICAL ADJUSTMENTS .............................................................................................................................. 10
CIRCUIT CHECK .................................................................................................................................................... 12
CHAPTER 2 SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA .............................................................................................................................. 13
LOCATION OF CONTROLS ................................................................................................................................... 14
PROGRAMMING CHANNEL MEMORY................................................................................................................. 16
CHASSIS AND CABINET REPLACEMENT PARTS LIST ......................................................................................18
PC BOARDS BOTTOM VIEW ................................................................................................................................. 33
TERMINAL VIEW OF TRANSISTORS ................................................................................................................... 45
CIRCUIT BLOCK DIAGRAM .................................................................................................................................. 47
SPECIFICATIONS .............................................................................................................................................. END
APPENDIX:
CIRCUIT DIAGRAM

–3 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION”AND “PRODUCT SAFETY NOTICE”INSTRUCTIONS BELOW.
X-RAY RADIATION PRECAUTION
1. Excessive high voltage can produce potentially hazardous
X-RAY RADIATION. To avoid such hazards, the high volt-
age must not be above the specified limit. The nominal value
of the high voltage of this receiver is (A) kV at zero beam
current (minimum brightness) under a (C) V AC power source.
The high voltage must not, under any circumstances, ex-
ceed (B) kV.
Refer to table-1 for high voltage (A), (B) & AC voltage (C).
(See SETTING & ADJUSTING DATA on page 13)
Each time a receiver requires servicing, the high voltage
should be checked following the HIGH VOLTAGE CHECK
procedure in this manual. It is recommended that the read-
ing of the high voltage be recorded as a part of the service
record. It is important to use an accurate and reliable high
voltage meter.
2. The only source of X-RAY RADIATION in this TV receiver
is the picture tube. For continued X-RAY RADIATION pro-
tection, the replacement tube must be exactly the same
type tube as specified in the parts list.
3. Some part in this receiver have special safety-related char-
acteristics for X-RAY RADIATION protection. For contin-
ued safety, parts replacement should be undertaken only
after referring to the PRODUCT SAFETY NOTICE below.
SAFETY PRECAUTION
WARNING : Service should not be attempted by anyone unfamiliar with the necessary precautions on this receiver. The following
are the necessary precautions to be observed before servicing this chassis.
1. An isolation transformer should be connected in the power line between the receiver and the AC line before any service is
performed on the receiver.
2. Always discharge the picture tube anode to the CRT conductive coating before handling the picture tube. The picture tube
is highly evacuated and if broken, glass fragments will be violently expelled. Use shatter proof goggles and keep picture tube
away from the unprotected body while handling.
3. When replacing a chassis in the cabinet, always be certain that all the protective devices are put back in place, such as; non-
metallic control knobs, insulating covers, shields, isolation resistor-capacitor network etc.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are
often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using
replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety char-
acteristics are identified in this manual and its supplements; electrical components having such features are identified by
the international hazard symbols on the schematic diagram and the parts list.
Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement
parts which do not have the same safety characteristics as specified in the parts list may create shock, fire, X-ray
radiation or other hazards.

–4 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION”AND “PRODUCT SAFETY NOTICE”ON PAGE 3 OF SERVICE MANUAL.
SET-UP ADJUSTMENT (FOR FLAT TUBE)
■The following adjustments should be made when a complete realignment is required or a new picture tube is installed.
Perform the adjustments in order as follows :
1. Color Purity
2. Convergence
3. White Balance
Note: The PURITY/CONVERGENCE MAGNET assembly and rubber wedges need mechanical positioning.
Refer to figure 1.
COLOR PURITY ADUSTMENT
(1) Let the screen face in the installing direction or toward the east (when it is to be moved), bring up the service mode
screen after demagnetizing (front, left, right, and top) with the degaussing coil, receive white signals by pressing the [TV/
VIDEO] button, and then the receiver should be operated for more than 40 minutes.
(2) Perform rough adjustment of the central convergence with the P/C magnet according to the adjustment item.
(3) Receive built-in green signals, loosen set screws on the deflection yoke, remove rubber wedges, and shift the deflection
yoke to toward front.
(4) Move alternately the two 2-pole magnets of the P/C magnets so that the green raster can come to the center of the
screen.
Figure 1.
(5) Receive built-in red and blue signals, check that there is no inclination of the single color raster toward one side, and if
each color tilts to a great extent, make adjustment with the 2-pole magnet so that the 3 colors will come to the center
evenly.
(6) Receive the green raster, shift the deflection yoke
from a foremost position (hitting against the picture
tube) to a backward position horizontally, stop the
deflection yoke at a position where it begins to
become a green raster, and perform accurate marking
on the picture tube.
(7) Shift the deflection yoke further backward, and
perform accurate marking at a position where the
green raster begins to being luck.
(8) Fix the deflection yoke at a position 60% forward
within the range marked in items (6) and (7) above.
CONVERGENCE ADJUSTMENTS
* Adjust the convergence magnet to get vest convergence in the the order to (1) ~ (5).
■ CENTER CONVERGENCE:
(1) Receive the white crosshatch or dot pattern from the service signal generator.
(2) Use the 2 pieces of main 4-pole magnets of P/C magnets, change the open angle, and align the red and blue vertical
lines on the screen center.
(3) Freeze the open angle of the main 4-pole magnets, turn them simultaneously, and align the horizontal lines.
(4) Take the same steps for items (2) and (3) above and align red/blue with green on the screen center using two 6-pole
magnets.
A
P/C magnet installing position A
• 30"=26.5 mm
• 32"=30.5 mm or 32.5 mm
• 34"=37 mm
• 34"=39 mm
Green Belt
2-pole purity magnet
(27": Magnet is fixed with deflection yoke.)
Main 4-pole convergence magnet (30" : 32")
6-pole convergence magnet (34")
Sub-4-pole convergence magnet (32" : 34")
Sub-4-pole convergence magnet (to be installed on deflection yoke for 30", 32”)
6-pole convergence magnet (30" : 32")
Main 4-pole convergence magnet (34")
Fix the deflection yoke at a position 60% forward from a
point between (6) and (7)
Picture tube
Shift deflection yoke
(6)
(8)
(7) Perform marking of each point
on the tape of picture tube
CRT-D board
P/C Mag
100 60 0%

–5 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
(5)Adjust the sub-4-pole magnets only in case there is any deviation of Xv bow-shaped convergence. (To be usually set at
the initial position)
Align both sides with the sub-4-pole magnets and minimize the deviation of blue and red with the main 4-pole magnets.
blue
blue
red
red
Main 4-pole magnet
red/blue
red/blue
green
green
6-pole magnet
Xv bow-shaped deviation of convergence
blue
red
Sub-4-pole magnet
■CIRCUMFERENCE CONVERGENCE:
*Perform correction in the following manner.
A
D
E
F
A
B
C
B
C
S
N
D
E
F
A
B
C
D
E
F
N
S
VR3
YV YHC
GH
GH
VR2 VR1
blue
green
red
•Adjust coils and minimize deviation
(The 27”unit has coils underneath it)
blue
green
red
(Parts code:23 948 274) TC-S
Blue color or blue mark
*Insert the correction piece between the
picture tube and the deflection yoke.
(Insertion position of correction
piece)
Bonded surface
blue
green
red
(Parts code:23 948 464)
Transparent
Bonded surface
Adjust VR 1 and minimize the deviation of YH. *Only 27", 30" and 32".
Red
green
blue
Red
green
blue
Red
green
blue
Red
green
blue
Adjust VR 2 (YHC) and minimize the deviation of YH.
Red
green
blue
Red
green
blue
Red
green
blue
Red
green
blue
Adjust VR 3 (YV) and minimize the deviation of YV.
Red
blue
green
Red
blue
green
Red
blue
green
Red
blue
green
Red
blue
green
blue
red
green
Red
blue
green
blue
red
green
■ 30", 27", 32"
■ 34"
27" (Part No. 23 947 371)
32", 30" (Part No. 23 947 121)
34" (Part No. 23 993 080)
Perform correction by inserting the
correction piece into the clear-
ance of terminal board coils of
the deflection yoke.
Note:
Perform insertion by turning the
metal side to the terminal board
side of the deflection yoke.

–6 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
SERVICE MODE
1. ENTERING TO SERVICE MODE
S
(Service mode display)
Item
Data
(or SOUND MUTE)
3) While pressing the obutton,
press MENU button on TV set.
2) Press obutton again to
keep pressing.
2. DISPLAYING THE ADJUSTMENT MENU
1) Press MENU button on TV.
3. KEY FUNCTION IN THE SERVICE MODE
The following key entry during display of adjustment menu provides special functions.
A single horizontal line ON/OFF: - / - - button (on Remote) or abutton (on TV)
Test signal selection : abutton (on Remote)
Selection of the adjustment items : Channel s/t(on TV or Remote)
Change of the data value : Volume ;+/–(on TV or Remote)
Adjustment menu mode ON/OFF : MENU button (on TV)
Initialization of the memory (QA02) : CALL + Channel button on TV (s)
Reset the count of operating protect
circuit to “00”: CALL + Channel button on TV (t)
“RCUT”selection : 1 button
“GCUT”selection : 2 button
“BCUT”selection : 3 button
“CNTX”(or “SCNT”) selection : 4 button
“COLC”selection : 5 button
“TNTC”selection : 6 button
Test audio signal ON/OFF (1kHz) : 8 button
Self diagnostic display ON/OFF : 9 button
1) Press obutton once on
Remote Control.
Adjustment mode
Press
Press
Service mode
Item
Data
S
Color thickness correction
note: Displayed differently as shown below, de-
pending on the setting of the receiving color
system.
COLP (PAL)
COLC (NTSC)
COLS (SECAM)
CAUTION : Never try to perform initialization unless you have changed the memory IC.

–7 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
4. SELECTING THE ADJUSTING ITEMS
1)Every pressing of CHANNEL sbutton in the service mode changes the adjustment items in the order of table-2.
(tbutton for reverse order)
Refer to table-2 for preset data of adjustment mode.
(See SETTING & ADJUSTING DATA on page 13)
5. ADJUSTING THE DATA
1) Pressing of VOLUME ;+/–button will change the value of data in the range from 00H to FFH. The variable range
depends on the adjusting item.
6. EXIT FROM SERVICE MODE
1) Pressing POWER button to turn off the TV once.
■INITIALIZATION OF MEMORY DATA OF QA02
After replacing QA02, the following initialization is required.
1. Enter the service mode, then select any register item.
2. Press and hold the CALL button on the Remote, then press the CHANNEL sbutton on the TV.The initialization of QA02 has
been complated.
3. Check the picture carefully. If necessary, adjust any adjustment item above.
Perform “Auto search Memory”on the owner’s manual.
CAUTION: Never attempt to initialize the data unless QA02 has been replaced.
7. TEST SIGNAL SELECTION
1) Every pressing of abutton on the Remote Control changes the built-in test patterns on screen as described below
in SERVICE MODE.
Signals Picture
•Red raster
•Green raster
•Blue raster
•All White
•Black cross-hatch
* The signals marked with are not usable to display in the Test signal for some model.
Signal off NTSC signals (5 patterns)
PAL signals (5 patterns)

–8 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
8. SELF DIAGNOSTIC FUNCTION
1) Press “9”button on Remote Control during display of adjustment menu in the service mode.
The diagnosis will begin to check if interface among IC’s are executed properly.
2) During diagnosis, the following displays are shown.
23xxxxxx
POWER
BUS CONT
BLOCK
: 000
: OK
: UV V1 V2 V3
V4
SELF CHECK S
Part number of microprocessor (QA01)
Operation number of protecting circuit ----“00”is nor-
mal.
When indication is other than “00”, overcurrent apts to
flow, and circuit parts may possibly be damaged.
BUS CONT ----“OK”is normal.
When indication shows “Q uuu NG”, the device with
the number may possibly be damaged.
BLOCK
UV : TV reception mode
V1 : VIDEO 1 input mode (a1)
V2 : VIDEO 2 input mode (a2)
V3 : VIDEO 3 input mode (a3)
V4 : VIDEO 4 input mode (a4)
Indicated color of mode now selected : Green and Red
Indicated color of other modes : White
Green : Normal
Red : The microprocessor operates to provide judgement
of no video signal. The red color is still indicated
though the signal is input, failure may exist in input
signal line including QV01.





–9 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
DESIGN MODE
1. ENTERING TO DESIGN MODE
ITEM
DATA
S D Press
(Design mode) (Adjustment mode)
Press
3) Press MENU button on TV.
2) While pressing o(or CALL) button on
Remote and press MENU button on TV.
1) Select the Service mode.
2. SELECTING THE ADJUSTING ITEMS
Every pressing of CHANNEL tbutton in the design mode changes the adjustment items in the order of table-3.
(sbutton for reverse order)
Refer to table-3 for data of design mode.
(See SETTING & ADJUSTING DATA on page 13)
3. ADJUSTING THE DATA
Pressing of VOLUME sor tbutton will change the value of data.
When QA02 is initialized, items “OPT0”, “OPT1”, “OPT2”and “OPT3”of DESIGN MODE are set to the data of the representative
model of this chassis family.
Therefore, because ON-SCREEN specification remains in the state of the representative of model. This model is required to
reset the data of items “OPT0”, “OPT1”, “OPT2”and “OPT3”.

–10 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
ELECTRICAL ADJUSTMENTS
1. Enter the service mode, then select any register item.
2. Press the TV/VIDEO button on the Remote until the black cross-bar pattern ap-
pears on the screen.
3. Adjust the FOCUS control (on T461) for well defined scanning lines on the picture
screen.
FOCUS VR ADJ
SUB-BRIGHTNESS
(BRTC)
Note: Constrict the picture height
until the vertical retrace line
appears adjusting the item
HIT (HEIGHT).
1. Set CONTRAST to minimum, and
BRIGHTNESS to center by adjusting user
controls.
2. Set the TV in service mode to get Black
cross-bar of inside pattern.
3. Select BRTC (brightness correction), and
adjust the ;–/+ button to reduce the
value so that white portion of inside pat-
tern slightly light.
4. Adjust ;–/+ button to increase the data
value of BRTC, and set it just before the
difference between the belt of vertical re-
trace and the border of black portion of
inside pattern is visible.
After that, return vertical height and con-
trast.
ITEM ADJUSTMENT PROCEDURE
Belt of vertical retrace
HORIZONTAL POSITION
ADJUSTMENT (HPOS)
VERTICAL POSITION
ADJUSTMENT (VPOS)
1. Set the TV in service mode, and get
black cross-bar signal with VIDEO
button on remote hand unit.
2. Select either HPOS (Horizontal pic-
ture phase) or VPOS (Vertical picture
phase) with CHANNEL s, tbuttons,
and adjust horizontal or vertical pic-
ture position in the center of screen
with VOLUME ;–/+ buttons.
VERTICAL AMPLITUDE
ADJUSTMENT (HIT)
1. Set the TV in service mode, and get
black cross-hatch signal with VIDEO
button on remote hand unit.
2. Select HIT (Vertical amplitude) with
CHANNEL s, tbuttons, and adjust
vertical amplitude with VOLUME
;–/+ buttons so that vertical am-
plitude lacks a little.
3. Adjust vertical amplitude with VOL-
UME ;–/+ buttons so that the first
bar on cross-hatch signal touches
edge of screen.
The first

–11 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
ITEM ADJUSTMENT PROCEDURE
1. Call up the adjustment mode display, then select the item WID.
2. Press the ;–/+ button to get the picture so the left and rightedges of raster
begins to lack.
3. Press the ;–/+ button to advance the data by 7 steps.
Note : Check the horizontal picture position is correct.
1. Call up the adjustment mode display, then select the item PARA.
2. Press the abutton on Remote until the cross-hatch pattern appears on the screen.
3. Press the ;–/+ button to make vertical lines straight as shown below.
WIDTH
(WID)
E-W PARABOLA
(PARA)
WHITE BALANCE
ADJUSTMENT
•CUTOFF ADJUSTMENT
(RCUT)
(GCUT)
(BCUT)
•DRIVE ADJUSTMENT
(GDRV)
(BDRV)
1. Set Contrast to 40, and brightness to +20 by picture control.
2. Receive the Black and White pattern.
3. Select RCUT, GCUT and BCUT with CHANNEL s, tbuttons, to set individual
values to Initial reference data, and to set GDRV and BDRV to Initial reference
data with VOLUME ;–/+ buttons.
4. Press -/- - button on the remote control and rotate Screen VR to get one slight
horizontal line on screen.
Note: Every pressing of -/- - button provides Horizontal line picture and Normal
picture alternately.
5. Press -/- - button to release horizontal line picture, and select the two other colors
which did not light in the above step with CHANNEL s, tbuttons. Then tap VOL-
UME ;–/+ buttons so that three colors slightly light in the same level.
XTo correct white balance in light area,
select GDRV and BDRV with CHANNEL
s, tbuttons to adjust.
XTo correct white balance in dark area,
perform fine adjustment of RCUT, GCUT
and BCUT.
Light area check
(to show white)
Dark area check
(to show black)

–12 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
CIRCUIT CHECK
HIGH VOLTAGE CHECK
CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps below.
1. Connect an accurate high voltage meter to the second anode of the picture tube.
2. Turn on the receiver. Set the BRIGHTNESS and CONTRAST controls to minimum (zero beam current).
3. High voltage must be measured below (B) kV.
Refer to table-1 for high voltage (B).
(See SETTING & ADJUSTING DATA on page 13)
4. Vary the BRIGHTNESS control to both extremes to be sure the high voltage does not exceed the limit under any conditions.

–13 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA
29" 34"
HIGH VOLTAGE AT ZERO BEAM: (A) 32.8 kV 33.2 kV
MAX HIGH VOLTAGE: (B) 33.0 kV 35.0 kV
AC VOLTAGE (C) 110~240 V 110~240 V
CHAPTER 2 SPECIFIC INFORMATIONS
SAFETY INSTRUCTIONS
Table-1
SERVICE MODE
ADJUSTING ITEMS AND DATAS IN THE SERVICE MODE:
Item Name of adjustment Preset
RCUT
GCUT
BCUT
GDRV
BDRV
CNTX
BRTC
COLC
TNTC
COLP
COLS
SCNT
VOLS
FVOL
NVOL
NICL
NICH
IDL
R CUTOFF (B/W)
G CUTOFF (B/W)
B CUTOFF (B/W)
G DRIVE
B DRIVE
CONTRAST MAX
SUB BRIGHTNESS CEN
COLOR CEN NTSC
SUB TINT CEN
COLOR CEN PAL
COLOR CEN SECAM
SUB CONTRAST FOR TV
VOL SCART
FM VOL PRE SCALE
NICAM VOL PRE SCALE
NICAM THRESHOLD LEVEL
NICAM THRESHOLD LEVEL
IGR THRESHOLD LEVEL
40H
40H
40H
35H
35H
7FH
80H
1AH
1FH
FBH
1AH
19H
75H
15H
3CH
03H
0AH
90H
Table-2
29"
←
←
←
←
←
←
←
←
1CH
←
←
←
←
←
←
←
←
←
Item Name of adjustment Preset 29"
IDH
EVOL
HPOS
VPOS
HIT
VLIN
VSC
VPS
VCP
WID
PARA
CNR
TRAP
HCP
VFC
SRY
SBY
IGR THRESHOLD LEVEL
Volume out data on Woofer
operation
H-POSITION DFS/100
V-POSITION DFS/100
PICTURE HEIGHT DFS/100
V-LINEARITY DFS/100
V-S CORRECTION DFS/100
V-BALANCE DFS/100
V-COMPENSATION DFS/100
H-WIDTH DFS/100
E-W PARABOLA DFS/100
E-W CORNER DFS/100
TRAPEZIUM DFS/100
H-COMPENSATION DFS/100
V-ƒCORRECTION DFS/100
SECAM R-Y BLACK LEVEL
SECAM-B-Y BLACK LEVEL
A0H
03H
32H
80H
40H
12H
33H
40H
02H
59H
1CH
19H
44H
03H
08H
07H
04H
←
←
34H
88H
48H
0AH
←
←
←
55H
17H
17H
46H
←
←
←
←
DESIGN MODE
ADJUSTING ITEMS AND DATAS IN THE DESIGN MODE:
Item Name of adjustment Preset Data Data
Data 29" 34"
OPT0
OPT1
OPT2
OPT3
OPT4
OPT5
Table-3
OPTION 0
OPTION 1
OPTION 2
OPTION 3
OPTION 4
OPTION 5
02H
42H
04H
FDH
62H
C8H
←
←
←
DFH
←
C0H
←
←
←
←
←
←
←
←
1CH
←
←
←
←
←
←
←
←
←
34" 34"
←
←
32H
80H
40H
12H
←
←
←
59H
1CH
19H
44H
←
←
←
←
←
←
←
DFH
←
C0H

–14 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
LOCATION OF CONTROLS
Back
Front
L/MONO R
AUDIOVIDEO
(3) MENU
CH
S-VIDEO
Remote sensor
POWER indicator
ON-TIMER indicator
a(3) Video 3 input
terminals
Headphones jacks
L : For private listening, connect headphones. The sound from the speakers will be cut off automatically.
To adjust the volume, press the –;+ buttons.
l : Use this jack when listening to the sound of the sub-picture (Picture-in-Picture).
Behind the door
(MONITOR)
(FIXED)
(1)(
2)( 4)
COMPONENT
VIDEO INPUT
COMPONENT
VIDEO INPUT
(HD)
L/MONO
S-VIDEO
VIDEO
AUDIO
R
Y
P B/
C B/
P R/
C R/
Y AUDIO
L
R
P
B/
C B/
P R/
C R/
FIXED AUDIO output
terminals
a(1) Video 1 input terminals
a(2) Video 2 input/COMPONENT VIDEO INPUT terminals
q POWER switch
Input source selection
MENU
a(4) Video 4 input/COMPONENT VIDEO INPUT (HD) terminals
Antenna input
MONITOR output
terminals
Headphones jacks
(ø3.5 mm)
LMain sound
lPIP sound
Channel position ts
Menu
–;+Volume –+
Menu < >

–15 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
Remote Control
Number buttons (0-9)
DVD
MENU
CH
CH
STILL
PIC SIZE
PIP PIP CHSEARCH STROBE
21 3
54 6
87 9
VCR
TV
DVD
0
ENTER
F CALL
MENU EXIT
Sound mute
Input source selection
(A1 –A4)
EXIT
Selectable sound
Power on/Standby
(For Toshiba TV/VCR/DVD only)
Device switch
TV: To control TV
VCR: To control VCR
DVD: To control DVD
•Volume –+
•Menu <>
Super woofer on/off
When in TV mode:
mI/II Stereo/Bilingual selection
PIP PIP on/off
STILL PIP STILL
PIPCH 89 PIPchannel selection
STROBE Multi-Window strobe
SEARCH Multi-Window search
F
+ rPIP locate
F
+ sPIP swap
F
+ aPIP source selection
ENTER
Picture STILL
When in VCR or DVD mode:
(For Toshiba VCR/DVD only)
Jto PAUSE
cto EJECT
to SKIP-REWIND
to SKIP-FORWARD
Sto PLAY
Rto STOP
to REWIND
to FAST FORWARD
Picture size selection
•CH (Channel position) st
•Menu
MENU
Selectable picture
1 or 2 digit channel selection
F
CALL

–16 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
To preset channels (ASM, SEARCH)
1
2
3
4
5
ASM (Automatic Search Memo r y)
Select the first position number you want to start the
ASM with the CH st or the Number buttons.
Press the MENU button, then press the <or >button
to display the SET UP menu.
Confirm that “COLOR”is set to “AUTO”and “SOUND”
is set to proper system.
If not, press the button, then press the <or >but-
ton to select proper system.
Press the button to select ASM.
Press the >(+) button to start the ASM. All active chan-
nels will be preset automatically.
When presetting is complete, the initial position number
will reappear.
After presetting
Check the preset channels by pressing the CH sor tbutton.
•If the color of a certain channel is abnormal, the automatic
color system selection (AUTO) may have malfunctioned, or
sound system selection is wrong. In such a case, select
another color and/or sound system.
1
SEARCH
Press the MENU button, then press the <or > button
to display the SET UP menu.
Press the (or ) button to select SEARCH.
Press the <or >button to start searching. The <
button searches for lower-numbered channels; the >
button for higher-numbered channels.
Repeat this process until you can get the desired chan-
nel.
When the desired channel is shown, press the
button to select POSITION.
Press the <or >button repeatedly until the position
number to be preset.
Press the button to select MEMORY, then press
the >(+) button to store the channel at the current
position.
When you program other channels, repeat steps 2 to
6.
2
3
4
•First, use the ASM (Automatic Search Memory) function to preset all the active channels in your area automatically.
Then, arrange the preset channels with the SEARCH, SKIP functions, MFT (Manual Fine Tuning) so that you can tune
into only desired channels.
•Use the SEARCH function if desired channels cannot be preset with the ASM or if you would like to preset channels to
specific position numbers one by one.
PROGRAMMING CHANNEL MEMORY
5
6
7

–17 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
AFT (Automatic Fine Tuning)
The AFT function automatically corrects slight fluctuations
when receiving signals.
Select the channel you want to fine-tune with the CH s
tbuttons or Number buttons.
While in the AFT OFF mode, “R”mark appears to the
left of the position number.
Press the MENU button, then press the <or >button
to display the SET UP menu.
Press the (or ) button to select AFT (on 2nd
page), then press <or >button to select ON.
To use the Antenna attenuator
When visual interference occures, set the Antenna attenuator
(ANT ATT) to ON.
Press the MENU button, then press the <or >
button to display the SET UP menu.
Press the (or ) to selectANT ATT (on 2nd page),
then press <or >button to select ON.
Note
This setting is effective for the programme position you are
now watching.
•After presetting the channels, you may skip unnecessary position numbers so that only the channels you want to watch
are selected.
To preset channels (SKIP, MFT)
To skip unnecessary position number
Select the position number to be skipped with the CH
stbuttons or Number buttons.
Press the MENU button, then press the <or >button
to display the SET UP menu.
Press the (or ) button to select SKIP.
Press the <or >button to select ON.
Press the EXIT button to erase the menu display,
then select the position number to be skipped with
the Number buttons. "*"mark appears to the left of
the position number. The position number will then be
skipped when you select channels with the CH st
buttons.
To restore a skipped position number
Select the position number you want to restore with
the Number buttons.
Select OFF in step 4 above.
MFT (Manual Fine Tuning)
The adjustments below are not necessary under normal re-
ceiving conditions. However, in areas of inferior broadcast con-
ditions where adjustment is necessary for a better picture,
perform the MFT.
Select the channel you want to fine-tune with the CH
stbuttons or Number buttons.
Press the MENU button, then press the <or >button
to display the SET UP menu.
Press the (or ) button to select MFT (on 2nd
page).
Press the <or >button until the best possible picture
and sound are obtained.
Note
When operating the MFT function, the AFT status is automati-
cally set to OFF.
1
1
2
3
4
5
2
3
4
To preset channels
(AFT, ANT ATT)
1
2
1
2
3
1
2

SPECIFIC INFORMATIONS
Location Parts No. Description
No.
Location Parts No. Description
No.
– 18 –
SPECIFIC INFORMATIONS
CAPACITORS
C101 24796479 ELECTROLYTIC, 35V 4.7UF M
C102 24793221 ELECTROLYTIC, 10V 220UF M
C105 24109102 CERAMIC CHIP, 50V B 1000PF K
C106 24797100 ELECTROLYTIC, 50V 10UF M
C107 24794221 ELECTROIYTIC, 16V 220UF M
C109 24109103 CERAMIC CHIP, 50V B 0.01UF K
C115 24109103 CERAMIC CHIP, 50V B 0.01UF K
C190 24109103 CERAMIC CHIP, 50V B 0.01UF K
C201 24793471 ELECTROLYTIC, 10V 470UF M
C202 24109103 CERAMIC CHIP, 50V B 0.01UF K
C205 24797229 ELECTROLYTIC, 50V 2.2UF M
C206 24794220 ELECTROLYTIC, 16V 22UF M
C219 24105100 CERAMIC CHIP, 50V CH 10PF D
C220 24105100 CERAMIC CHIP, 50V CH 10PF D
C221 24105100 CERAMIC CHIP, 50V CH 10PF D
C302 24214471 CERAMIC DISC, 500V B 470PF K
C303 24214471 CERAMIC DISC, 500V B 470PF K
C305 24669222 ELECTROLYTIC, 50V 2200UF M 3A
C308 24797221 ELECTROLYTIC, 50V 220UF M
C309 24591102 PLASTIC FILM, 50V 1000PF J (34SH9UH)
C310 24669222 ELECTROLYTIC, 50V 2200UF M 3A
C313 24082057 PLASTIC FILM, 100V 0.22UF J
C315 24212102 CERAMIC DISC, 50V B 1000PF K (29SH9UH)
C316 24795471 ELECTROLYTIC, 25V 470UF M
C317 24214102 CERAMIC DISC, 500V B 1000PF K (34SH9UH)
C318 24794471 ELECTROLYTIC, 16V 470UF M
C320 24795471 ELECTROLYTIC, 25V 470UF M
C321 24503051 PLASTIC FILM, 63V 0.68UF J
C322 24617915 ELECTROLYTIC, 50V 1UF K 3A LI
C323 24503049 PLASTIC FILM, 63V 0.47UF J
C325 24590223 PLASTIC FILM, 50V 0.022UF J
C326 24797010 ELECTROLYTIC, 50V 1UF M (29SH9UH)
C327 24794471 ELECTROLYTIC, 16V 470UF M
C331 24503038 PLASTIC FILM, 63V 0.056UF J
C332 24212102 CERAMIC DISC, 50V B 1000PF K
C366 24082049 PLASTIC FILM, 100V 47000PF J
C370 24794100 ELECTROLYTIC, 16V 10UF M
C390 24591102 PLASTIC FILM, 50V 1000PF J
C391 24666100 ELECTROLYTIC, 10V 10UF M 3A (34SH9UH)
C392 24085981 ELEC. NONPOLAR CE04J 16V 10UF M
11L NP (34SH9UH)
C393 24666100 ELECTROLYTIC, 10V 10UF M 3A (34SH9UH)
C396 24503065 PLASTIC FILM, 1800VH 1800PF H (34SH9UH)
C410 24794471 ELECTROLYTIC, 16V 470UF M
C410 24829563 PLASTIC FILM, 400V 0.056UF J
C413 24214392 CERAMIC DISC, 500V B 3900PF K
C416 24676330 ELECTROLYTIC, 100V 33UF M 3A
C416 24591102 PLASTIC FILM, 50V 1000PF J
C417 24214391 CERAMIC DISC, 500V B 390PF K
C419 24212102 CERAMIC DISC, 50V B 1000PF K
C420 24666101 ELECTROLYTIC, 16V 100UF M 3A
C421 24539104 PLASTIC FILM, 50V 0.1UF J
C423 24503251 PLASTIC FILM, 400V 0.18UF J (29SH9UH)
C423 24503191 PLASTIC FILM, 400V 0.13UF J (34SH9UH)
C432 24073059 ELECTROLYTIC, 25V 3300UF M 3A
C432 24503041 PLASTIC FILM , 63V 0.1UF J
C433 24232103 CERAMIC DISC, 50V F 0.01UF Z
C433 24503195 PLASTIC FILM, 1800VH 5100PF H (29SH9UH)
C433 24503099 PLASTIC FILM, 1800VH 4700PF H (34SH9UH)
C434 24820103 PLASTIC FILM, 630V 0.01UF J
C436 24503041 PLASTIC FILM , 63V 0.1UF J
C437 24503346 PLASTIC FILM, 1800VH 3300PF H
C439 24829473 PLASTIC FILM, 400V 0.047UF J (29SH9UH)
C439 24503126 PLASTIC FILM, 400V 0.082UF (34SH9UH)
C442 24503251 PLASTIC FILM, 400V 0.18UF J (29SH9UH)
C442 24503192 PLASTIC FILM, 400V 0.15UF J (34SH9UH)
C443 24503346 PLASTIC FILM, 1800VH 3300PF H (29SH9UH)
C443 24503067 PLASTIC FILM, 1800VH 2200PF (34SH9UH)
C444 24503346 PLASTIC FILM, 1800VH 3300PF H (29SH9UH)
C444 24503347 PLASTIC FILM, 1800VH 3600PF H (34SH9UH)
C445 24829473 PLASTIC FILM, 400V 0.047UF J
C446 24073120 ELECTRPLYTIC, 250V 33UF, 250YXF33M
C448 24640962 ELECTROLYTIC, 200V 33UF M
C449 24667471 ELECTROLYTIC, 25V 470UF M 3A
C450 24092341 CERAMIC DISC, 2KV R 470PF K
C451 24092341 CERAMIC DISC, 2KV R 470PF K
C453 24503346 PLASTIC FILM, 1800VH 3300PF H
C454 24503195 PLASTIC FILM, 1800VH 5100PF H
C460 24591683 PLASTIC FILM, 50V 0.068UF J
C464 24503149 PLASTIC FILM, 250V 3.3UF
C465 24503253 PLASTIC FILM, 1250VH 0.01UF H
C467 24503253 PLASTIC FILM, 1250VH 0.01UF H
C470 24794101 ELECTROLYTIC, 16V 100UF M
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRE-
CAUTION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF THIS MANUAL.
CAUTION: The international hazard symbols “ ” in the schematic diagram and the parts list designate components
which have special characteristics important for safety and should be replaced only with types identical to those in the
original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals.
Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE. Do not degrade the
safety of the receiver through improper servicing.
NOTICE:
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model
number and Description.
• The PC board assembly with *mark is no longer available after the end of the production.
Model : 29SH9UH, 34SH9UH
Capacitors ............. CD : Ceramic Disk PF : Plastic Film EL : Electrolytic
Resistors ............... CF : Carbon Film CC : Carbon Composition MF : Metal Film
OMF : Oxide Metal Film VR : Variable Resistor FR : Fusible Resistor
(All CD and PF capacitors are ±5%, 50V and all resistors, ±5%, 1/6W unless otherwise noted.)
CHASSIS AND CABINET REPLACEMENT PARTS LIST

Location Parts No. Description
No.
Location Parts No. Description
No.
–19 –
SPECIFIC INFORMATIONS
C471 24539104 PLASTIC FILM, 50V 0.1UF J
C472 24539474 PLASTIC FILM, 50V 0.47UF J
C473 24073081 ELECTROLYTIC, 50V 1.OUF M 3A
C475 24214102 CERAMIC DISC, 500V B 1000PF K
C476 24082637 PLASTIC FILM, 400V 0.1UF J (29SH9UH)
C476 24829273 PLASTIC FILM, 400V 0.027UF J (34SH9UH)
C476 24794220 ELECTROLYTIC, 16V 22UF M
C477 24591182 PLASTIC FILM, 50V 1800PF J
C479 24214471 CERAMIC DISC, 500V B 470PF K
C481 24214121 CERAMIC DISC, 500V B 120PF K
C482 24591103 PLASTIC FILM, 50V 0.01UF J (29SH9UH)
C483 24591223 PLASTIC FILM, 50V 0.022UF J (29SH9UH)
C483 24591682 PLASTIC FILM, 50V 6800PF J (34SH9UH)
C486 24539104 PLASTIC FILM, 50V 0.1UF J
C487 24539104 PLASTIC FILM, 50V 0.1UF J
C489 24539103 PLASTIC FILM, 50V 0.01UF J (34SH9UH)
C491 24591223 PLASTIC FILM, 50V 0.022UF J
C492 24539474 PLASTIC FILM, 50V 0.47UF J
C493 24539104 PLASTIC FILM, 50V 0.1UF J (29SH9UH)
C493 24591683 PLASTIC FILM, 50V 0.068UF J (34SH9UH)
C493 24829243 PLASTIC FILM, 400V 0.024UF J
C494 24539104 PLASTIC FILM, 50V 0.1UF J
C496 24591103 PLASTIC FILM, 50V 0.01UF J
C497 24829333 PLASTIC FILM, 400V 0.033UF J (29SH9UH)
C497 24829273 PLASTIC FILM, 400V 0.027UF J (34SH9UH)
C498 24539104 PLASTIC FILM, 50V 0.1UF J (29SH9UH)
C498 24591473 PLASTIC FILM, 50V 0.047UF J (34SH9UH)
C510 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C513 24109103 CERAMIC CHIP, 50V B 0.01UF K
C514 24794101 ELECTROLYTIC, 16V 100UF M
C515 24085958 ELEC. NONPOLAR, 50V 1UF M
C516 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C517 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C518 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C520 24591334 PLASTIC FILM, 50V 0.33MF J
C530 24797010 ELECTROLYTIC, 50V 1UF M
C531 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C532 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C533 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C534 24797478 ELECTROLYTIC, 50V 0.47UF M
C535 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C536 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C537 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C538 24797010 ELECTROLYTIC, 50V 1UF M
C539 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C540 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C541 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C542 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C547 24109103 CERAMIC CHIP, 50V B 0.01UF K
C548 24794101 ELECTROLYTIC, 16V 100UF M
C563 24797478 ELECTROLYTIC, 50V 0.47UF M
C564 24797479 ELECTROLYTIC, 50V 4.7UF M
C586 24206100 ELECTROLYTIC, 50V 10UF M 7L 3A
C587 24109222 CERAMIC CHIP, 50V B 2200PF K
C588 24105561 CERAMIC CHIP, 50V CH 560PF J
C589 24109332 CERAMIC CHIP, 50V B 3300PF K
C601 24591102 PLASTIC FILM, 50V 1000PF J
C602 24591102 PLASTIC FILM, 50V 1000PF J
C603 24073084 ELECTROLYTIC, 50V 4.7UF M 3A
C604 24073084 ELECTROLYTIC, 50V 4.7UF M 3A
C605 24073052 ELECTROLYTIC, 25V 47UF M 3A
C606 24073052 ELECTROLYTIC, 25V 47UF M 3A
C607 24503042 PLASTIC FILM, 63V 0.12UF J
C608 24503042 PLASTIC FILM, 63V 0.12UF J
C609 24073094 ELECTROLYTIC, 50V 1000UF M 3A
C610 24073094 ELECTROLYTIC, 50V 1000UF M 3A
C611 24073053 ELECTROLYTIC, 25V 100UF M 3A
C612 24073084 ELECTROLYTIC, 50V 4.7UF M 3A
C613 24794471 ELECTROLYTIC, 16V 470UF M
C614 24797010 ELECTROLYTIC, 50V 1UF M
C615 24073094 ELECTROLYTIC, 50V 1000UF M 3A
C616 24503042 PLASTIC FILM, 63V 0.12UF J
C620 24073084 ELECTROLYTIC, 50V 4.7UF M 3A
C621 24567104 PLASTIC FILM, 50V 0.1UF J
C623 24797220 ELECTROLYTIC, 50V 22UF M
C626 24073094 ELECTROLYTIC, 50V 1000UF M 3A
C627 24797010 ELECTROLYTIC, 50V 1UF M
C628 24794470 ELECTROLYTIC, 16V 47UF M
C630 24073052 ELECTROLYTIC, 25V 47UF M 3A
C631 24073086 ELECTROLYTIC, 50V 10UF M 3A
C632 24073053 ELECTROLYTIC, 25V 100UF M 3A
C655 24794101 ELECTROLYTIC, 16V 100UF M
C656 24591273 PLASTIC FILM, 50V 0.027UF J
C657 24797330 ELECTROLYTIC, 50V 33UF M
C661 24797330 ELECTROLYTIC, 50V 33UF M
C662 24797330 ELECTROLYTIC, 50V 33UF M
C680 24073094 ELECTROLYTIC, 50V 1000UF M 3A
C681 24797010 ELECTROLYTIC, 50V 1UF M
C704 24591822 PLASTIC FILM, 50V 8200PF J
C705 24232103 CERAMIC DISC, 50V F 0.01UF Z
C707 24794470 ELECTROLYTIC, 16V 47UF M
C712 24666470 ELECTORLYTIC, 16V 47UF M 3A
C713 24709100 ELECTROLYTIC, 200V 10UF M
C714 24436101 CERAMIC DISC, 50V SL 100PF J
C715 24214472 CERAMIC DISC, 500V B 4700PF K
C716 24436101 CERAMIC DISC, 50V SL 100PF J
C717 24214472 CERAMIC DISC, 500V B 4700PF K
C718 24766470 ELECTROLYTIC, 50V 47UF M
C719 24435560 CERAMIC DISC, 500V SL 56PF J
C720 24709100 ELECTROLYTIC, 200V 10UF M
C721 24797470 ELECTROLYTIC, 50V 47UF M
C726 24212102 CERAMIC DISC, 50V B 1000PF K
*C801 24503002 PLASTIC FILM, AC275V 0.22UF M
*C802 24503057 PLASTIC FILM, AC275V 0.22UF M
C805 24092281 CERAMIC DISC, AC250V E 4700PF
C806 24092281 CERAMIC DISC, AC250V E 4700PF
C807 24539474 PLASTIC FILM, 50V 0.47UF J
C808 24796101 ELECTROLYTIC, 35V 100UF M
C809 24539474 PLASTIC FILM, 50V 0.47UF J
C810 24073106 400V680UF LLQ2G681MHSET
*C811 24092567 CERAMIC DISC, AC250V E 1000PF M
*C813 24092563 CERAMIC DISC, AC250V B 220PF K
*C814 24092563 CERAMIC DISC, AC250V B 220PF K
*C815 24092567 CERAMIC DISC, AC250V E 1000PF M
C816 24794470 ELECTROLYTIC, 16V 47UF M
C817 24092339 CERAMIC DISC, 2KV 330PF K
C818 24095931 PLASTIC FILM, 1250VH 2200PF J
C819 24676220 ELECTROLYTIC, 100V 22UF M 3A
C821 24214471 CERAMIC DISC, 500V B 470PF K
C823 24214471 CERAMIC DISC, 500V B 470PF K
C825 24539104 PLASTIC FILM, 50V 0.1UF J
C828 24797470 ELECTROLYTIC, 50V 47UF M
C829 24212271 CERAMIC DISC, 50V B 270PF K
C831 24665470 ELECTROLYTIC, 10V 47UF M 3A
C832 24665470 ELECTROLYTIC, 10V 47UF M 3A
C833 24669229 ELECTROLYTIC, 50V 2.2UF M 3A
C834 24669100 ELECTROLYTIC, 50V 10UF M 3A
C835 24666470 ELECTORLYTIC, 16V 47UF M 3A
C840 24762102 ELECTROLYTIC, 10V 1000UF M
C841 24669100 ELECTROLYTIC, 50V 10UF M 3A
C842 24669100 ELECTROLYTIC, 50V 10UF M 3A
C843 24539104 PLASTIC FILM, 50V 0.1UF J
C850 24214471 CERAMIC DISC, 500V B 470PF K
C851 24669471 ELECTROLYTIC, 50V 470UF M 3A

–20 –
Location Parts No. Description
No.
Location Parts No. Description
No.
SPECIFIC INFORMATIONS
C853 24591563 PLASTIC FILM, 50V 0.056UF J
C855 24214222 CERAMIC DISC, 500V B 2200PF K
C856 24212102 CERAMIC DISC, 50V B 1000PF K
C858 24666470 ELECTORLYTIC, 16V 47UF M 3A
C859 24591103 PLASTIC FILM, 50V 0.01UF J
C861 24591104 PLASTIC FILM, 50V 0.1UF J
C863 24669222 ELECTROLYTIC, 50V 2200UF M 3A
C865 24669222 ELECTROLYTIC, 50V 2200UF M 3A
C866 24214331 CERAMIC DISC, 500V B 330PF K
C867 24214331 CERAMIC DISC, 500V B 330PF K
C868 24092281 CERAMIC DISC, AC250V E 4700PF
C869 24086937 ELECTROLYTIC, 450V 120UF M 22D
C870 24092281 CERAMIC DISC, AC250V E 4700PF
C871 24668470 ELECTROLYTIC, 35V 47UF M 3A
C872 24095939 PLASTIC FILM, 1250VH 1000PF J
C873 24212122 CERAMIC DISC, 50V B 1200PF K
C874 24503056 PLASTIC FILM, AC275V 0.1UF M
C875 24092563 CERAMIC DISC, AC250V B 220PF K
C876 24092563 CERAMIC DISC, AC250V B 220PF K
C877 24212221 CERAMIC DISC, 50V B 220PF K
C878 24092339 CERAMIC DISC, 2KV 330PF K
C880 24212101 CERAMIC DISC, 50V B 100PF K
C884 24086916 ELECTROLYTIC, 160V 330UF M 3D
C887 24214471 CERAMIC DISC, 500V B 470PF K
C891 24667472 ELECTROLYTIC, 25V 4700UF M 3A
C893 24092337 CERAMIC DISC, 2KV 220PF K
C895 24668221 ELECTROLYTIC, 35V 220UF M 3A
C896 24214471 CERAMIC DISC, 500V B 470PF K
C897 24667222 ELECTROLYTIC, 25V 2200UF M 3A
C898 24667222 ELECTROLYTIC, 25V 2200UF M 3A
C899 24214471 CERAMIC DISC, 500V B 470PF K
C902 24092345 CERAMIC DISC, 2KV 1000PF K
C903 24436221 CERAMIC DISC, 50V SL 220PF J
C905 24436221 CERAMIC DISC, 50V SL 220PF J
C907 24436221 CERAMIC DISC, 50V SL 220PF J
C909 24679470 ELECTROLYTIC, 250V 47UF M 3A
C911 24203100 ELECTORLYTIC, 16V 10UF M 7L 3A
C913 24763102 ELECTROLYTIC, 16V 1000UF M
C914 24092398 CERAMIC DISC, 25V 0.1UF Z, 24092398A
NI TOOITSU
C918 24092398 CERAMIC DISC, 25V 0.1UF Z, 24092398A
NI TOOITSU
C919 24092398 CERAMIC DISC, 25V 0.1UF Z, 24092398A
NI TOOITSU
C920 24436221 CERAMIC DISC, 50V SL 220PF J
C921 24436221 CERAMIC DISC, 50V SL 220PF J
C922 24436221 CERAMIC DISC, 50V SL 220PF J
C931 24214101 CERAMIC DISC, 500V B 100PF K
C963 24436391 CERAMIC DISC, 50V SL 390PF J
C964 24436331 CERAMIC DISC, 50V SL 330PF J
C965 24436331 CERAMIC DISC, 50V SL 330PF J
C3110 24539104 PLASTIC FILM, 50V 0.1UF J
C4000 24591102 PLASTIC FILM, 50V 1000PF J
C4030 24591103 PLASTIC FILM, 50V 0.01UF J
C4201 24794101 ELECTROLYTIC, 16V 100UF M
C4202 24794101 ELECTROLYTIC, 16V 100UF M
C4300 24109103 CERAMIC CHIP, 50V B 0.01UF K
C4311 24794221 ELECTROIYTIC, 16V 220UF M
C4401 24109103 CERAMIC CHIP, 50V B 0.01UF K
C4402 24797010 ELECTROLYTIC, 50V 1UF M
C4403 24794331 ELECTROLYTIC, 16V 330UF M
C4404 24109103 CERAMIC CHIP, 50V B 0.01UF K
C4405 24092730 CERAMIC CHIP, 16V B 0.1UF K
C4422 24085988 ELECTROLYTIC, NONPOLAR, 50V
1.0UF M 7L
C4461 24539474 PLASTIC FILM, 50V 0.47UF J
C4462 24085958 ELEC. NONPOLAR, 50V 1UF M
C4464 24797010 ELECTROLYTIC, 50V 1UF M
C5020 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C5030 24794101 ELECTROLYTIC, 16V 100UF M
CA09 24105101 CERAMIC CHIP, 50V CH 100PF J
CA10 24105101 CERAMIC CHIP, 50V CH 100PF J
CA14 24232103 CERAMIC DISC, 50V F 0.01UF Z
CA30 24105101 CERAMIC CHIP, 50V CH 100PF J
CA33 24100103 CERAMIC CHIP, 50V F 0.01UF Z
CA42 24666100 ELECTROLYTIC, 10V 10UF M 3A
CA43 24109103 CERAMIC CHIP, 50V B 0.01UF K
CA45 24105330 CERAMIC CHIP, 50V CH 33PF J
CA68 24794100 ELECTROLYTIC, 16V 10UF M
CA69 24100103 CERAMIC CHIP, 50V F 0.01UF Z
CA80 24794100 ELECTROLYTIC, 16V 10UF M
CA89 24105101 CERAMIC CHIP, 50V CH 100PF J
CA90 24100103 CERAMIC CHIP, 50V F 0.01UF Z
CA91 24100103 CERAMIC CHIP, 50V F 0.01UF Z
CA92 24666101 ELECTROLYTIC, 16V 100UF M 3A
CA93 24100103 CERAMIC CHIP, 50V F 0.01UF Z
CA95 24794220 ELECTROLYTIC, 16V 22UF M
CA96 24100103 CERAMIC CHIP, 50V F 0.01UF Z
CA99 24666100 ELECTROLYTIC, 10V 10UF M 3A
CB01 24744470 ELECTROLYTIC, 16V 47UF M
CB40 24092538 CERAMIC CHIP, 10V F 1UF Z
CB41 24109222 CERAMIC CHIP, 50V B 2200PF K
CB42 24105561 CERAMIC CHIP, 50V CH 560PF J
CB43 24109332 CERAMIC CHIP, 50V B 3300PF K
CB90 24100103 CERAMIC CHIP, 50V F 0.01UF Z
CC01 24109102 CERAMIC CHIP, 50V B 1000PF K
CC02 24109102 CERAMIC CHIP, 50V B 1000PF K
CC03 24109102 CERAMIC CHIP, 50V B 1000PF K
CC04 24109102 CERAMIC CHIP, 50V B 1000PF K
CC05 24109102 CERAMIC CHIP, 50V B 1000PF K
CC06 24109102 CERAMIC CHIP, 50V B 1000PF K
CC07 24109102 CERAMIC CHIP, 50V B 1000PF K
CC08 24109102 CERAMIC CHIP, 50V B 1000PF K
CC09 24109102 CERAMIC CHIP, 50V B 1000PF K
CC10 24109102 CERAMIC CHIP, 50V B 1000PF K
CC11 24212102 CERAMIC DISC, 50V B 1000PF K
CC12 24212102 CERAMIC DISC, 50V B 1000PF K
CC13 24232103 CERAMIC DISC, 50V F 0.01UF Z
CC14 24232103 CERAMIC DISC, 50V F 0.01UF Z
CC15 24232103 CERAMIC DISC, 50V F 0.01UF Z
CC16 24590103 PLASTIC FILM, 50V 0.01UF J
CC25 24590223 PLASTIC FILM, 50V 0.022UF J
CC31 24353101 CERAMIC DISC, 50V CH 100PF J
CC32 24353101 CERAMIC DISC, 50V CH 100PF J
CD01 24797100 ELECTROLYTIC, 50V 10UF M
CD02 24797220 ELECTROLYTIC, 50V 22UF M
CD03 24503041 PLASTIC FILM , 63V 0.1UF J
CD04 24503041 PLASTIC FILM , 63V 0.1UF J
CD05 24590102 PLASTIC FILM, 50V 1000PF J
CD06 24503045 PLASTIC FILM, 63V 0.22UF J
CD07 24797229 ELECTROLYTIC, 50V 2.2UF M
CD08 24794221 ELECTROIYTIC, 16V 220UF M
CD09 24232103 CERAMIC DISC, 50V F 0.01UF Z
CD10 24797479 ELECTROLYTIC, 50V 4.7UF M
CD11 24797479 ELECTROLYTIC, 50V 4.7UF M
CD12 24797479 ELECTROLYTIC, 50V 4.7UF M
CD13 24797479 ELECTROLYTIC, 50V 4.7UF M
CD14 24797479 ELECTROLYTIC, 50V 4.7UF M
CD15 24797479 ELECTROLYTIC, 50V 4.7UF M
CD16 24797479 ELECTROLYTIC, 50V 4.7UF M
CD17 24503045 PLASTIC FILM, 63V 0.22UF J
CD18 24590102 PLASTIC FILM, 50V 1000PF J
CD19 24590103 PLASTIC FILM, 50V 0.01UF J
CD20 24590333 PLASTIC FILM, 50V 0.033UF J