Totem GIRAFFE User manual

It is a good idea to
start every step in-
serting nuts into
beams (if the step
requires).
Use the back of the
screwdriver to push
in the nuts.
After entering the
rst slot, nuts tend
to tilt. Use your
thumb to push it
back straight, and
then again use the
screwdriver to in-
sert the nut all the
way in.
Push Nylon
Stando with your
thumb while tight-
ening it with the
wrench.
Some of the nuts
are missing threads.
This is a manufac-
turing issue and we
are working on it. In
the mean time, we
add few extra nuts.
We apologize for
the inconvenience.
Use Beam/Bolt
ruler to determine
the length of beams
and bolts.
For more tips, please visit the link below:
https://totemmaker.net/blog/totem-mechanics-for-beginners/
STARTING TIPS
Inserting nuts (1) Inserting nuts (2) Faulty threads Tightening
standos
Ruler

PART LIST
7x Beam 90 mm 4x Beam 40 mm 10x Bolt M3x6 1x Bolt M3x8 8x Bolt M3x10 6x Bolt M3x25
2x Bolt M3x35 4x Lock Nut M3 25x Nut M3 6x10 2x 2-Hole 45 Bracket 1x 2-Hole 45 Simple Bracket 2x 2-Hole Simple Bracket
2x C-Bracket 4x Strip Bracket 75 mm 6x Nylon Spacer 4 mm 2x Nylon Spacer 8 mm 4x Nylon Stando M3x8 2x DC Motor Hub
2x DC Motor Bracket 1x Battery Case with Switch 1x DC Motor 1x Totem Screwdriver 1x Totem Wrench

1
2
2x Beam 90 mm 5x Nut M3 6x10
2x Bolt M3x10 1x DC Motor Bracket
#4
#4
#1
# indicates number
of circular hole.
indicates counting
direction.

3
4
2x Bolt M3x25 2x Nut M3 6x10
1x DC Motor 2x Bolt M3x10
1x DC Motor Bracket
#4
#4
# indicates number
of circular hole.
indicates counting
direction.

5
6
2x Bolt M3x25
2x Beam 40 mm 2x Bolt M3x35
2x Nylon Spacer 4 mm 4x Nut M3 6x10
Tighten the
bolts rmly.
6

2x Bolt M3x6 1x Step 6 Assembly
1x Step 7 Assembly
7
8
2x DC Motor Hub 2x Bolt M3x25
2x Nut M3 6x10
Repeat this step twice.
2x
Tighten the
bolt rmly.
Screw bolt with strength as
the hub’s hole is tight t.

9
10
2x Beam 90 mm 2x Nylon Stando
1x C-Bracket 3x Nut M3 6x10
1x Bolt M3x6
Do not use much
force when tightening
Nylon Standos.
1x Step 8 Assembly 1x Step 9 Assembly
#6
#6
Use wrench for
Nylon Standos.
# indicates number
of circular hole.
indicates counting
direction.

11
1x Strip Bracket 1x Bolt M3x10
1x Nylon Spacer 4 mm 1x Lock Nut M3
Do not use much
force when tightening
Bolt into Stando.
Use wrench for
Lock Nut.
Do not over-tighten
Strip Bracket. Bracket
must be slightly loose.

12
Do not use much
force when tightening
Bolt into Stando.
1x Strip Bracket 1x Nylon Spacer 4 mm
1x Nylon Spacer 8 mm 1x Lock Nut M3
1x Bolt M3x10
Use wrench for
Lock Nut.
Do not over-tighten
Strip Bracket. Bracket
must be slightly loose.

Do not use much
force when tightening
Nylon Standos.
13
2x Beam 90 mm 2x Nylon Stando
1x C-Bracket 3x Nut M3 6x10
1x Bolt M3x6
Use wrench for
Nylon Standos.

14
1x Step 12 Assembly 1x Step 13 Assembly
# indicates number of circular hole.
#6
#6
indicates counting direction.

15
Do not use much
force when tightening
Bolt into Stando.
1x Strip Bracket 1x Bolt M3x10
1x Nylon Spacer 4 mm 1x Lock Nut M3
Use wrench for
Lock Nut. Do not over-tighten
Strip Bracket. Bracket
must be slightly loose.

16
1x Strip Bracket 1x Nylon Spacer 4 mm
1x Nylon Spacer 8 mm 1x Lock Nut M3
1x Bolt M3x10
Do not use much
force when tightening
Bolt into Stando.
Use wrench for
Lock Nut.
Do not over-tighten
Strip Bracket. Bracket
must be slightly loose.

1x Beam 90 mm 2x Beam 40 mm
5x Bolt M3x6 5x Nut M3 6x10
2x 2-Hole Simple
Bracket
1x 2-Hole 45 Simple
Bracket
17
# indicates number
of circular hole.
#1
#1 #2
#3
#1
#1
#1
#1
#1
#1 indicates counting
direction.

18
2x 2-Hole 45 Bracket 1x Bolt M3x8
1x Nut M3 6x10
# indicates number
of circular hole.
indicates counting
direction.
#1

19
1x Bolt M3x6
20
1x Battery Case with Switch
Connect motor
with battery switch.
#1

Loosen Lock Nuts (if needed, on both
sides) if motor cannot move legs.
Tighten Lock Nuts (if needed, on both
sides) if legs are too wobbly.
Your Girae is
now alive and
ready to play.
Woohoo!

www.totemmaker.net
Aldrea lalas Totem, UAB
Sauletekio al. 15-709, Vilnius, 10224, Lithuania
For customer support please contact: [email protected]
KEEP THIS INTRUCTION MANUAL AND THE PRODUCT BOX AS IT CONTAIN IMPORTANT INFORMATION FOR FUTURE REFERENCE.
Due to the continuous product improvement, the pictures on this manual may dier slightly from the actual product. Please adhere to actual product instead.
WARNING:
CHOKING HAZARD - Small parts.
Not for children under 3 years.
Totem Maker names and logos are registered trademarks. All rights reserved.
Note to adults: to ensure that the child’s play is both safe and fun, please review all operating instructions and safety rules with your child.
Do not give this product to children aged 3 or below. As with all electronic products, precautions should be observed during handling and use.
Adult supervision required.
SAFETY WARNINGS:
• Do not pick up toy while in motion.
• Keep ngers, hair, and loose clothing away from moving parts, to avoid the injury.
• If the toy is dirty, please clean it with dry and soft cloth.
• Do not expose the vehicle to high temperature, high humidity, or direct sunlight.
• Indoor use only. Functions best on hard, at surface.
• Do not put this product in water,
• Do not disassemble or modify the motor.
TO AVOID BATTERY LEAKAGE:
• Do Always follow the instrutions carefully. Use only batteries specied and be sure to insert them correctly by matching the + and – polarity markings.
• Do not mix old batteries and new batteries or standard (carbon-zinc) with alkaline batteries.
• Remove exhausted or dead batteries from the product.
• Remove batteries if product is not to be played with for a long time.
• Do not short-circuit the supply terminals.
• RECHARGEABLE batteries: Do not mix these with any other type of batteries. Always remove from the product before recharging. Recharge batteries under
adult supervision. DO NOT RECHARGE OTHER TYPES OF BATERIES.
• Should this product cause, or be aected by local electrical interference, move it away from other electrical equipment.
BATTERY INFORMATION:
• 2x 1.5V AA batteries required (not included).
• To insert batteries, use cross head screwdriver
(not included).