Totem HOCKEY BOT User manual

v.1.5

It is a good idea to
start every step in-
serting nuts into
beams (if the step
requires).
Use the back of the
screwdriver to push
in the nuts.
After entering the
rst slot, nuts tend
to tilt. Use your
thumb to push it
back straight, and
then again use the
screwdriver to in-
sert the nut all the
way in.
Use the Totem
Wrench Socket
(Blue) to insert Ny-
lon Standos used
to assemble the
electronics boards.
Some of the nuts
are missing threads.
This is a manufac-
turing issue and we
are working on it. In
the mean time, we
add few extra nuts.
We apologize for
the inconvenience.
Use Beam/Bolt
ruler to determine
the length of beams
and bolts.
For more tips, please visit the link below:
https://totemmaker.net/blog/totem-mechanics-for-beginners/
STARTING TIPS
Inserting nuts (1) Inserting nuts (2) Faulty threads Tightening
standos
Ruler

BEFORE YOU START BUILDING:
Bolt colours codes:
We have put some colours on bolts to
make instructions more clear.
NOTE: 2x 8mm
Notes for bolts other than 6mm:
When bolts that are not 6mm will be used, in
addition to colours, extra notes are given in
the instructions with lengths in mm.
6mm bolts and 6x10mm nuts:
When starting on a building step, the 6mm bolts
and 6x10 nuts are coloured RED. It makes it
easier to see where the new bolts and nuts are
placed.
12cm
I-beams lengths.
When a new Totem beam is needed in a step,
the length is indicated.

Positions for nuts with #-symbol.
When it is helpful, the slot-number is indicated
in the Totem beam. Starting from #1 and count-
ing slots.
Green Rotating Arrows = rotating action.
When a connection is a rotating hub, you must
not tighten the bolt and nut too much. Test it for a
smooth rotation, but not too wobbly either.
#1 #6 #8 #12
Don’t tighten
link too much.
The colour of parts.
The colours of plastic part may vary. Colours are
often changed on parts to make it easier to see
them in the instructions pictures.
Helpful little tool:
Included in the kit is a
small hex-socket used for
fastening Lock Nuts and
Nylon Towers. The pointy
end is for Lock Nuts.
Totem Wrench Socket

51x
Bolt M3x6
4x
Bolt M3x10
6x
Bolt M3x8
1x
Bolt M3x25
1x
Bolt M3x12
1x
Bolt M3x20
62x
Nut M3 6x10
8x
2-hole Simple
4x
2-hole 45 simple
4x
Single side ller
5x
Lock Nut M3
1x
Metal washer M3
9x0.8mm
2x
L-Twisted
2x
L-Twisted mirror
8x
C-Bracket
4x
Nylon Stando
M3x8mm
4x
Bolt M3x35
6x
Nylon Spacer 4mm
1x
Nylon Spacer 8mm
3x
2-hole bracket
2x
Yellow DC Motor
bracket
2x
Yellow DC motor 1:48
2x
Yellow Wheel D 67mm
1x
Li-Ion 3.7v Battery
1x
X3 Controller Board
1x
5.5mm Totem Wrench
1x
Caster Wheel Kit
5-7x
ZIP Tie
1x
Washer 1mm
DIA24mm
2x
Rubber Band
1x
USB Battery Charger
1x
Totem Screw Driver
3 cm 6x
4 cm 3x
6 cm 1x
8 cm 2x
10 cm 4x
12 cm 2x
6.5cm/13H 1x
12cm/24H 1x
PARTS NEEDED:
1x
Mini Servo Motor
1x
Arm for Mini
Servo Motor
1x
Bolt M2.5x8
For servo arm
Explanation:
13H = 13 holes
1x
Servo arm Index
Disc set
1x
Allen hex key
1x
Totem Wrench Socket

2x
PART 1
2x
12
34
16x
Bolt M3x6
4x
Bolt M3x8
4x
Bolt M3x35
20x
Nut M3 6x10
4x
C-Bracket
2x
L-Twisted
2x
L-Twisted mirror
3 cm 4x
4 cm 2x
10 cm 2x
2x
Yellow DC Motor
bracket
2x
Yellow DC motor 1:48
NOTE: 2x 8mm
3 cm
4 cm
3 cm

NOTE: This tap
to this side.
OBS: 2x 35mm
PART 1
5
6
78
10cm
2x 2x

PART 2
1
2
20x
Bolt M3x6
20x
Nut M3 6x10
2x
C-Bracket
3 cm 2x
6 cm 1x
10 cm 1x
12 cm 2x
8x
2-hole Simple
4x
2-hole 45 simple
12cm
4x
Single side ller
#1 #6 #8 #12

3
4
3cm
6cm
TIP:
How to insert the 45 de-
gree Filler part:
1: First assemble brackets
with bolts.
2: Bolts are a bit loose.
3: Insert ller as shown.
4: Tighten bolts again.

5
6
10cm
#1
#4
#7 #10

PART 2
7
8

PART 3 1
2
4x
Bolt M3x6
9x
Nut M3 6x10
PART1
1x
Caster Wheel Kit
2x
Yellow Wheel D 67mm
4x
Nylon Stando
M3x8mm
#2
#8
Use the Totem
Wrench Socket

3
4
PART2

5
6
#2
#8
Use the Totem
Wrench Socket

1x
Caster Wheel Kit
Caster Wheel Kit:
Read in the Robotics Kit Booklet in page 30 and 31 about how to
build a Caster Wheel set.
The colour green and yellow in the instructions are for clarity
only, the actual colour may be dierent.
You can skip putting a
beam to the caster wheel
set here.
Just temporary put a
6x10mm nut there to
hold it together during
building the caster set.
Skip Step4,
it is not
needed.

7
8
Use the included Allen key to easier tighten the bolt.
#3.5
#3
#1
#4 Put the
Caster
Wheel in
the middle.
#3.5 means
the hole be-
tween the #3
and #4 slot.

PART 3
9
10

PART 4 1
2
2x
Bolt M3x6
6x
Nut M3 6x10
8 cm 1x
6.5cm/13H 1x
12cm/24H 1x
4x
Bolt M3x10
1x
Bolt M3x12
3x
Lock Nut M3
2x
Bolt M3x8
NOTE: 8mm
1x
Metal washer
M3 9x0.8mm
3x
Nylon Spacer
4mm
NOTE: 10mm
NOTE: 10mm
1x
Mini Servo Motor
1x
Arm for Mini
Servo Motor
1x
Bolt M2.5x8
For servo arm
2x
2-hole bracket
#2
#4
#7
#5.5
Strip brackets:
13H = 13 holes
24H = 24 holes
View from other
side.

3
4

5
6
120mm/24H
65mm/13H
14 holes
Note: 10mm
Note: 12mm
Smooth spin
Use the Totem
Wrench Socket