Totevision LCD-1510V User manual

________________________________________ 15” LCD MONITOR
2
CHAPTER 1
INTRODUCTION
BEFORE INSTALLING YOUR MONITOR
Read this manual cover to cover.
PAY ATTENTION to all WARNING and CAUTIONS
DO NOT use computer components not recommend by the
manufacture
Do not attempt to service the monitor your self. If a problem
occurs, contact the manufacture's authorized service center
ABOUT YOUR MONITOR
This monitor is a microprocessor-controlled, color monitor that
uses a TFT LCD panel. The monitor conforms to EPA Energy
Star and VESA DPMS (Display Power Management Signaling)
power management standards.
RGB MODE
This monitor is equipped with a microprocessor that identifies
your computer 's video mode and allows user to adjust the setting.
VIDEO MODE
This monitor can accept the NTSC or PAL signal to display the
video screen automatically. It also implement the video screen on PC
function, we called PIP function. We also provide one pair of BNC
in/out connector inside.

15” LCD MONITOR _____________________________________
3
FACTORY-PRESET MODES
Table 1 shows standard video mode setting that has been
pre-adjusted at the factory for accurate video display. These setting
are stored in the monitor's memory
Table 1. Factory-Preset Modes
PC mode
Mode Resolution H-Freq.(KHz) V-Freq(Hz)
NEC 640x400 24.83 56.4
VGA 640x350
720x400
640x480
640x480
640x480
31.47
31.47
31.47
37.86
37.5
70
70
60
72
75
SVGA 800x600
800x600
800x600
800x600
35.16
37.88
48.08
46.87
56.3
60.3
72.2
75
XGA 1024x768
1024x768
1024x768
48.36
56.47
60
60
70
75
SXGA 1280x1024
1280x1024
63.98
80
60
75
Macintosh 640x480
832x624
1024x768
1024x768
35
49.7
48.78
60.241
66.7
74.55
60
74.927
Video Mode
NTSC 525 lines, 60 fields
PAL 625 lines, 50/60 fields
Note: The 15” LCD monitor didn’t support SXGA mode

________________________________________ 15” LCD MONITOR
4
SPECIFICATIONS
 LCD-1510V 15” LCD Monitor
Overall Dimension (HxWxD): 404 x 393 x 162 mm
Effective Display area (H/V): 304.1 x 228.1 mm
Display colors: 16.7M (dithering) colors
Scan Frequencies:
Horizontal 31.47K to 60KHz
Vertical 60Hz to 75Hz
Viewing Angle: 140°(Horizontal & Vertical)
Number of Pixels: 1024x768 pixels
Pixel pitch: 0.297x0.297 mm
Picture Tube: 15" TFT LCD panel
Power:
Input 110~240VAC (auto-sensing)
Frequency: 48-62Hz
Consumption 35Watts maximum (on)
1 Watts (Power saving off mode)
PC RGB Connector: 15pin Mini D-sub (Standard)
Audio connector 1 x stereo input
Speaker 2W x 2
RGB Signals:
Video Analog RGB 0.7Vp-p/75Ω
Sync Separate
Display Data Channel:
Compatibility VESA DDC 1/2B
Video connector Input
S-connector x 1 (S-video In)
AV connector x 3 ( one for video, Two for audio)
Mini D type x 1 (for YcbCr/Component In)
BNC connector x 1 ( Composite Video In)
Video Connector output

15” LCD MONITOR _____________________________________
5
BNC connector x 1 (Composite Video Out)
Operations:
User Controls On/Off Power Button
+/- and Up/down keys
On Screen Display Auto adjustment, Brightness, contrast
color temperature, Hue, Tint,
Source select, PIP setup
H-position, V-position, OSD position
Audio volume, bass, treble, mute
Load default
Control Type: Digital
Compatibility: IBM and compatible, Apple
Macintosh, NEC
Environmental Limits:
Operating Temp 32°to 103°F ( 0°to 40°C )
Storage Temp. -4°to 140°F ( -20°to 60°C )
Operating Humidity 10 to 85% without Condensation
Storage Humidity 10 to 95% without Condensation
Agency Approval
EMI FCC-B and CE
Emissions MPR-II
Energy Saving EPA energy star, VESA DPMS
Safety UL, TUV

__________________________________ 15”/17”/19” LCD MONITOR
22
Auto adjustment
Automatically adjusts the phase and position of the LCD monitor for the
best view setting
Color temperature setting
provide 9300K, user mode, and 6500K option
Brightness adjustment
Let user adjust the brightness. The range if from 0 to 99
.
Contrast setup
Provide
user to separately
adjust each R, G
and B contrast
and intensity
value. When Move to this icon, and press – or + key, then the screen will
show below
1024x768 60KHz 75Hz
VER XGA-KD841-5100
Color balance
Intensity R
Intensity G
Intensity B
Contrast R
Contrast G
Contrast B
- Execute +

15”/17”/19” LCD MONITOR
_____________________________________
23
Color balance: the monitor do the white balance automatically.
Intensity R: Adjust the R color intensity, the range is from 0 to 63
Intensity G: Adjust the G color intensity, the range is from 0 to 63
Intensity B: Adjust the B color intensity, the range is from 0 to 63
Contrast R: Adjust the R color contrast value, the range is from 0 to 63
Contrast G: Adjust the G color contrast value, the range is from 0 to 63
Contrast B: Adjust the B color contrast value, the range is from 0 to 63
Geometry setup
We provide Pixel Clock, Phase, H Position, V Position, OSD H Position,
OSD V Position and Txt/Gft option to change.
Pixel Clock: Adjust the viewing screen size. The range is from 0 to 99
Phase: Adjust phase tracking to reduce the display flicker. The range is from 0
to 31
H Position: Move the whole screen horizontally. The range is from 0 to 120.
V Position: Move the whole screen vertically. The range is from 0 to 100
OSD H Position: Move the OSD horizontally. The range is from 0 to 15
OSD V Position: Move the OSD screen vertically. The range is from 0 to 15
Txt/Gfx: Select the display mode as 640x480(graphic mode) or 720x400(text
mode)
PIP setup
We provide H Position, V Position, PIP H/V ratio, Contrast, Intensity, Tint
and Hue option for customer setup the PIP screen
H Position: Move the PIP screen Horizontally. The range is from 0 to 15
V Position: Move the PIP screen Vertically. The range is from 0 to 15
PIP H/V ratio: Provide four option from 1 to 4. When set as 4, it is 1: 1 ratio
as original size. Set as 3, it is 1/2 of original one. Set as 2, it is 1/4 of

__________________________________ 15”/17”/19” LCD MONITOR
24
original one. Set as 1, it is 1/8 of original size.
Contrast: Adjust the contrast value of PIP screen. The range is from 0 to 127.
Intensity: Adjust the intensity value of PIP screen. The range is from 0to 255
Tint: Adjust the Tine value of PIP screen. The range is from 0 to 255
Hue: Adjust the Hue value of PIP screen. The range is from 0 to 255
Source Select
We provide VGA, Composite, S-video, YCbCr, PIP composite, PIP
S-video,
PIP YCbCr and PIP off for user’s selection.
Note: The PIP function is only valid on video on VGA screen. We can’t
support video on video screen
Speaker volume control
We provide Volume, Bass, Treble, Mute and PIP audio for audio setup.
Volume: Adjust the speaker volume. The range is from 0 to 32
Bass: Adjust the speaker Bass value. The range is from 0 to 10
Treble: Adjust the speaker Treble value. The range is from 0 to 10
Mute: Enable or disable the Mute function
PIP audio: Enable or disable the PIP mute function
Load the factory default setting.
Restore the factory default setting.

15”/17”/19” LCD MONITOR
_____________________________________
25
CHAPTER 4
VIDEO ADJUSTMENT
Video OSD Screen
NTSC 15.7K 60.2
VER XGA-KDC45-5100
1. Each time, when pressing the menu key , the screen will show as
above. You can see the mark, that means the selected item Then you
can change the setting through + or -.key.
2. Pressing Sel key to move the arrow down or up. If the selected item has
many option to choose, press – or + to enter into the sub-menu.
3. Then move Sel key to item you want to change , the item will be
highlighted with red characters, then press – or + to change the value.
4. If you finish the setting, press the MENU to key to the main OSD, then
repeat the item 2 and 3.

Brightness
- Adjustment +
49

__________________________________ 15”/17”/19” LCD MONITOR
26
Brightness adjustment
Adjust the screen brightness value. The range if from 0 to 99.
Contrast adjustment
Adjust the screen contrast value. The range is from 0 to 127
Intensity adjustment
Adjust the screen intensity value. The range is from 0 to 255
Tint adjustment
Adjust the screen Tint value. The range is from 0 to 127
Hue adjustment
Adjust the screen Hue value. The range is from 0 to 255
Geometry setup
We provide Sharpness, H Position, V Position, OSD H Position, and
OSD V position.
Sharpness: Adjust the screen sharpness level. The range is from 0 to 15
H position: Move the screen horizontally. The Range is from 0 to 20
V Position: Move the screen vertically. The range is from 0 to 20
OSD H Position: Move the OSD horizontally. The range is from 0 to 15
OSD V Position: Move the OSD screen vertically. The range is from 0 to 15
Source Select
we provide VGA, Composite, S-video, YCbCr source for user’s selection
Speaker volume control
We provide Volume, Bass, Treble, Mute and PIP audio for audio setup.
Volume: Adjust the speaker volume. The range is from 0 to 32
Bass: Adjust the speaker Bass value. The range is from 0 to 10
Treble: Adjust the speaker Treble value. The range is from 0 to 10
Mute: Enable or disable the Mute function
PIP audio: Enable or disable the PIP mute function
Load the factory default setting.
Load the factory default setting