Totevision LCD-1900VRQ User manual

-
---

.........19" Quad display LCD monitor .........
CHAPTER 1
INTRODUCTION
BEFORE INSTALLING YOUR MONITOR
READ THIS MANUAL COVER TO COVER.
PAY ATTENTION to all WARNING and CAUTIONS
DO NOT use computer components not recommend by the
manufacture
Do not attempt to service the monitor your self. If a problem
occurs, contact the manufacture's authorized service center
ABOUT YOUR MONITOR
This monitor is a microprocessor-controlled, color monitor
which uses a TFT LCD panel. The monitor conforms to EPA
Energy Star and VESA DPMS ( Display Power Management .
Signaling) power management standards. Our monitor also
provide one option to accept the video input (like NTSC or PAL
signal), you can switch these input signal through OSD and the
video OSD setting please refer to the Chapter 4.
I
I
I
I
,I
RGB MODE
This monitor is equipped with a microprocessor that
identifies your computer's video mode and allows user to
adjust the setting.
1
I1
---
... ... 19"QuaddisplayLCDmonitor .........
FACTORY-PRESET MODES
Table 1 shows standard video mode setting that have been
pre-adjusted at the factory for accurate video display. These
setting are stored in the monitor's memory
Table 1. Factory-Preset Modes
..
2
Mode Resolution H-FreQ.(KHz) V-FreQ(Hz)
NEC 640x400 24.83 56.4
VGA 640x350 31.47 70
720x400 31.47 70
640x480 31.47 60
640x480 37.86 72
640x480 37.5 75
SVGA 800x600 35.16 56.3
800x600 37.88 60.3
800x600 48.08 72.2
800x600 46.87 75
XGA 1024x768 48.36 60
1024x768 56.47 70
1024x768 60 75
SXGA 1280x1024 63.98 60
1280x1024 80 75
Macintosh 640x480 35 66.7 .
832x624 49.7 74.55
1024x768 48.78 60
1024x768 60.241 74.927

19"Quaddisplay LCDmonitor........................
SPECIFICATIONS
.19"LCDMonitor
OverallDimension (HxWxD): 483 x 354 x 50.3 mm
ShippingWeight (GIW): 9 Kg
EffectiveDisplayarea (HN):376.3 x 301.056r:nm
Displaycolors: 16.7Mcolors
ScanFrequencies:
Horizontal
Vertical
Numberof Pixels:
Pixelpitch:
PictureTube:
Power:
Input
31.47K to 80KHz
60Hz to 75Hz
1280x1024 pixels
0.294xO.294 mm
19" TFT LCD panel
Consumption
RGB Connector:
BNC connector
110-240VAC(auto-sensing)
Frequency: 48-62Hz
45Watts maximum (on)
15pin Mini D-sub (Standard)
6 x BNC connector
4 x camera input
1 x playback
1 x recorder
RGB Signals:
Video
Sync
Display Data Channel:
Compatibility
Analog RGB 0.7Vp-pI75Q
Separate
VESA DDC 1/2B
3
I
... 19" Quad display LCD monitor ............
Compatibility:
Environmental Limits:
Operating Temp
Storage Temp.
Operating Humidity
Storage Humidity
Agency Approval
EMI
Safety
..
~
I
i
I
~
IBM and compatible, Apple
Macintosh, NEC
32° to 104°F (0° to 40°C)
-40to 140°F ( -20° to 60°C)
10 to 85% without condensation
10 to 95% without Condensation
FCC-A
UL
4
--

... ... ......19" Quaddisplay LCD monitor .........
Chapter 2
PRODUCT PACKAGE
Openthe shippingcartonandcheckthe contents. Ifany
items are missing or damaged,contactyour dealer
immediately.
The package should include the following items
. au 19" Color TFT LCD Monitor
. Accessory Box:
1. VGA cablex 1
2. AC to DCadapter x 1
3. PowerCord x 1
4. User's manualx 1
INSTAlliNG THE MONITOR
The monitor is equippedwith an auto sensingpowersupply
for voltage rangesfrom 110-240V AC, 60/50Hz. Confirm
the linevoltagedesignationonthe rearpanelof the
monitor.
5
I~
19"Quaddisplay LCDmonitor........................
.
FOllOW THESE STEPS TO INSTALL THE
MONITOR
1. Before you connect the cables, make sure that the
monitorandthe system unit powerswitchesare OFF
2. Plug one end of the 15pin signal cable to the monitor
and the other end to the video signal connector at the
rearof the system.Tightenthe two screwson the cable
connector on both ends, otherwise the screen will be
abnormal and LED light is yellow color, not the normal
greencolor.
3. Connect4 camerasthroughBNCcable
4. Connectout BNCto recorderto recordthe screen
5. Connectthe powerto the monitorthroughtheAC/DC
adapter
~
-1,
6

...... ......19"QuaddisplayLCDmonitor ...
Assembling R-191S is as follows:
(1)
'i
1
1
ij
I
!
,.
1. Prepareone metal-frame
with "M5" diameter.
(3)
'
Ii
i.
:!
:'
,.
I
,
. '
,
:
.
~'
.
'
~
'Ji'-
3. Lock 4 pieces of M5*1OLscrews
by using screwdriver.
I
(2)
2. Place R-191S on a fixed
position.
(4)
4. Completion of assembly
as show on diagram (4)
7
T
19"Quad display LCD monitor ...
CONTROL FUNCTIONS
Il'
The OSD control functions of 19" Quad display LCD monitor
are located on the lower side. They are shown in the figure
below and described in the following paragraphs.
Menu V t1 +I
AV/PCMenu!lCH1 j/CH2 -/CH3+/CH4 j/AUTO EB <.:J
The first line is used for RGB OSD adjustment
The second line is used for security OSD adjustment
AV/PC: Switch the Screen between RGB and security
screen.
The RGB control key description:
1. ~: Power Switch
2. - /+ : Decrement/Increment or Volume control
3. 'V//)" : Cursor Up/Down or Brightness control
4. MENU:Activatetheon screendisplayfunction .
As the security control key definition, please see the chapter 4.
1
1,.
8

... .19" Quad display LCDmonitor ......
II
II
Chapter 3
ADJUSTING THE PC MONITOR
The LCO monitor is designed to work with a range of
compatible video adapters on the market. Oue to the
possible deviations between these video adapters, you may
make some adjustment to fit the monitor for adapter used.
AOJUSTMENTPRaCEOURE
I. First, you must activate the aso screen through
pressing the MENU key, the screen will show in the
center of screen as below:
Note: In the last paragraph, we will assume that you
had already done this procedure and only explain how
to change the setting.
2. Use the \1 & 11key to select the required adjustment
item up or down.
3. Usethe -&+keyto changethe controlvaluefor
optimum viewing.
4. Each changethat you had madewill be automatically
saved into memory, If the screen displaygarbageand
you don'tknowhowto restoreto correctsetting,please
movearrowto "LoadValue" itemthen pressing"-" key
to loadfactorydefault.
9
I
,
J
19"Quaddisplay LCD monitor........................
We had two pages aso screens; the screens are shown in
aso screen 1 and 2, if you choose the source to video not
RGB, please see the next chapter.
aso SCREEN1
F
A
H
V
P
P
B
C
o
o
N
10
1024x768 48KHz 60Hz
JTOADJUSTMENT ffi
.pOSITION @
POSITION--
XEl CLOCK BH-position
-lASE E3
Ick light Bl
OlOR Temperature
SDH-position- [!!
SDV-position-
extpage
RMWARE VERSIOfo, SXGA5F211-5140

"
II
r
19"Quaddisplay LCDmonitor........................ 19"Quaddisplay LCD monitor .........
OSD SCREEN2 Adjustment Icon :
P
B
rn Auto-adjustment
Automaticallyadjustthe pixelclock, HN position
andfine tune the screento get bettervisual
quality.
rn H-position
Adjuststhe screen'swidth.The rangeis from
0-255.
I::J V-Position
Adjusts the screen's height. The Range is from
0-255.
EI Pixel Clock
Macro-adjust the screen size. The range is from
0-255
E3 Phase
Fine tune the screen size to get stable image
after you finish the EIsetting. The range is 0-31
BL Back light control
Adjust lamp current
~ ColorTemperature
Adjust the color temperature
() Contrast
Adjust RGB contrast values simultaneously, or
you can separately change each RGB value
~ 720/640 Selection
Select the Text or Graphic mode display
![] ase H-position
Move the OSD Horizontal Display location in the
Screen '
c
7
a
a
L
F
11 12
I
1024x768 48KHz 60Hz
EVIOUSPAGE-
'ightness
RED R
GREEN---- -G
BLUE B
Dntrast---- ()
RED -R 0 255
GREEN-- GVilliIIII I
BLUE-- B 128
W/640selection-
SD transparence -
SDtimeout- X
)ad Default-
REWARE VERSIC N SXGA 5F211-5140

'1
,
I..19" Quaddisplay LCDmonitor........................
[!!:!I OSD V-position
Changethe OSD Vertical Displaylocationin the
screen
Move to the next OSD screen
Moveto the previousOSD scr~en
OSDtransparency setting
To setthe OSDdisplay transparencymode.
Load default
OSDtime out timer setting
II ~~
~
(;J
~..
X
VERTICAL & HORIZONTAL POSITION ADJUSTMENT
1. Use the 'V& t!.key to move the ~ to the @ ICON, then
press - & +to move the wholescreen left or rightto
the center position.
2. Usethe 'V& t!.keyto movethe ~to the ~ ICON, then
press - & +to movethe wholescreendownor upto
the center position.
ADJUST THE VIEWING SCREEN SIZE
1. Usethe 'V& t!.key to movethe ~to the EI icon , then
press - & + to get the largerviewingsize.
2. Usethe 'V& t!.keyto move the ~to the EJicon ,then
pressthe - & + keyto get the stablesetting.
13
- I
... ...19" Quaddisplay LCD monitor ...
BRIGHTNESS ADJUSTMENT
1. Usethe 'V& t!.keyto movethe ~to the ~icon,then
press - &+ to getthe bestbrightnessoptimization.
Note: We provideanothereasilymethodto dothe
brightnessadjustment.You don't needto activatethe OSD
screen,just pressingthe - or +to changethe brightness
value.
CONTRAST ADJUSTMENT
Adjustthe displaycontrast
1. Usethe 'V& t!.keyto movethe ~to the () icon,then
press - & +to getthebestbrightnessoptimization.This
settingwill influenceali of RGBsetting,if you want to
individuallyset each RGBsetting,just movethe ~to the
next Color-R,Color-Gand Color-Biconto change.
OSD DISPLAY LOCATION ADJUSTMENT
Adjustthe OSD display location
1. Usethe 'V& t!.keyto movethe ~to the lIDand [!!:!Iicon,
then press - & + to changethe OSD locationas you
want horizontallyorvertically.
HOWTO RESTORETHE PRE-DEFINEVALUE
Restoreyour previousdefinesetting
14

......... 19"QuaddisplayLCDmonitor...... ............ 19"Quad display LCD monitor .........
1. Use the Y'& L1 key to move the ~ to the ~ icon,
then press "_"will automatically load the pre-define
value for each item.
2. Use this function only if you want to discard your new
setting.
CHAPTER 4
ADJUSTING THE SECURITY SCREEN
SETTING
UNDERSTANDTHE DISPLAYRESOLUTIONSETTING
To understand your display mode setting.
1. In the OSD screen, you will see the Horizontal
frequency (HF), Vertical frequency (VF), resolution and
the monitor Firmware version (ROM LEVEL). It is
automatically detected by the monitor user can not
change this setting.
Note: we recommend to use auto adjustment item to fine
tune the monitor setting to get the better visual quality.
The LCD monitor is designed to work with a range of
compatible video display on the market. Due to the possible
deviations between these video source, you may make some
adjustment to fit the monitor for video usage.
ADJUSTMENT PROCEDURE
1. First,you must activate.the OSDscreenthrough pressing.
the MENU key,the screenwill show inthe centerof screen
as below:
Note: Inthe last paragraph,we will assumethat you had already
donethis procedureand onlyexplain howto changethe setting.
3.
Use the V & l:1key to select the required adjustment item up
or down.
Use the - & +key to change the control value for optimum
viewing.
Any change that you make will be automatically saved into
memory, If the screen display is not optimal and you don't
know how to restore the correct setting, please move the
arrow to "Load Value" item then press "-" key to load factory
default settings.
2.
4.
15 16
I

...... ... .19"QuaddisplayLCDmonitor ... .19"QuaddisplayLCDmonitor... ...... ....
CAMERA SETUP
CAMERA
BRIGHTENSS
CONTRAST
SHARPNESS
SATU
SAT V
HUE
LOAD DEFAULT
You can set up each camera brightness, contrast, sharpness, sat U,
Sat V and hue setting to the better visual quality.
Security OSD menu setting
When your screen is in AV mode, pressing MENU key to enter into
OSD set up menu, you will see the following screen
SETUPMENU
SYSTEM
CAMERA
ALARM
PLAYBACK
VERSION
CAM1
10
22
55
99
82
01
You can use tor j key to move the highlight bar to the desired item,
then press J to enter into the sub-menu to change setting.
The sub-menu of alarm is below
IALARM SETUP
AUDIBLE
The sub-menu of system is below. OFF/ON
It lets users to set up the audible on of off when camera signal is
missing.
SYSTEMSETUP
FORMAT
DATE
TIME
DWELL
YY-MM-DD
03-03-31
14:18:13
1
The sub-menu of Playback is
CH1 CH2 CH3 CH4 PB OUT PWR PW
You can change the date format, current timing and dwell timing. We also offer the hot key to let users easily operate the R-191S
machine.
Pressing !lCH1 to let screen to display the channel 1 in full screen
Pressing j/CH2 to let screen to display the channel 2 in full screen
Pressing -ICH3 to let screen to display the channel 3 in full screen
Pressing +/CH4 to let screen to display the channel 4 in full screen
Pressing J/AUTO to let screen to display the screen as Channel, 1
Channel 2, Channel 3 , Channel 4, then Channel sequentially, the
duration is controlled by the DWELL setting in the system sub-menu.
Pressing B3 to let screen to display 4 channel quad display.
The sub-menu of camera is below
17
I
18

.19" Quaddisplay LCD monitor........................
Recording the screen will always set as quad display, When you
playback the screen, we offered one hot key to let user to see the full
channel # display. For example, if you want to see the playback
channel 1 in full screen, just pressing !/CH1, the screen will show
the full screen of channel 1.
19
I
... .,....19" Quaddisplay LCD monitor ..................
APPENDIX
SIGNAL CONNECTOR PIN-OUT
RGB SIGNAL CONNECTOR
20
Power Connector Ground
Pin 1
Pin2 +12Voutput
Pin 1 Analog Red Input
Pin2 Analog GreenInput
Pin3 Analog Blue Input
Pin4 Ground
Pin5 DigitalGround
Pin6 Analog Red Ground
Pin7 Analog GreenGround
Pin8 Analog BlueGround
Pin9 NC
Pin 10 SyncGround
Pin 11 Ground
Pin 12 SDA( DDCData)
Pin 13 H. Sync
Pin 14 V. Sync
Pin 15 SCl ( DDCClK )