Totnz TZCT1B User manual

TZCT1B / TZCT1V / TZCT1M
INSTRUCTION
MANUAL
Lift Top Coffee Table
Rev01(A)
[email protected]

Contents
M6 x 12mm
G x 4
M3.5 x 14mm
H x 22F x 8
M3.5 x 25mm
I x 16
M3.5 x 35mm
J x 14
B x 1 C x 24A x 1 D x 24 E x 6
⑨
⑧
⑩
⑪
⑫
⑥
⑤
③
①
⑦②
②
④
⑦
⑧
⑨
⑨
⑩
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

1. Screw the cam bolt [C] into the threaded insert on the panel.
2. Connect both panels together. Make sure cam bolt [C] goes into the small
pre-drilled hole on the end of the panel.
3. Insert the cam lock [D] into the pre-drilled cam lock large hole on the
panel. Make sure the open slot faces the head of the cam bolt [C].
4. Rotate the cam lock [D] clockwise with a self-supplied Phillips screwdriver
to lock the cam bolt [C] in place.
C
D
C C C
Tools Needed (NOT lncluded)
Cam Lock System Operation
Phillips Screwdriver Rubber Mallet
C
C
D
D
12 34
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

J
③
④
STEP 1
②*1 ③*1 ④*1 C*2 J*4
②
②
J
Phillips
Screwdriver
(NOT lncluded)
NOTE: Keep the grooves on
the panels ② ③ ④ are at the
same level.
J
J
C
C
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

STEP 2
⑤*1 ⑪*1 J*3
⑪
⑤
J
J
J
NOTE: Make sure the four big holes
point to the bottom in this step.
Phillips
Screwdriver
(NOT lncluded)
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

D
STEP 3
⑪
⑤
D
D
D
D*2
Phillips
Screwdriver
(NOT lncluded)
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

STEP 4
⑥*1
⑥
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

STEP 5
②*1 C*2 D*2 J*4
②
J
J
J
J
D
D
D
D
②
CC
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

STEP 6
⑫*1 J*3
J
J
J
⑫
J
NOTE: Keep these big holes
point to outwards in this step.
⑪
Phillips
Screwdriver
(NOT lncluded)
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

⑦*2 ⑧*2 C*10 D*6 F*4
D
D
D
⑦⑧
⑦
⑧
C
C
C
CC
X2 X2
Make sure these holes
face down in this step.
X2
X2
STEP 7
Phillips
Screwdriver
(NOT lncluded)
Rubber Mallet
(NOT lncluded)
Please NOTE that there is
NO pilot hole for furniture
sliders. Please use a rubber
mallet and gently tap them
right into place.
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

⑨*2 ⑩*2 C*10 D*6 F*4
⑨
⑩
F
D
D
Make sure these holes
face down in this step.
⑩
CC
C
C
C
⑨
X2 X2
X2 X2
STEP 8
Phillips
Screwdriver
(NOT lncluded)
Rubber Mallet
(NOT lncluded)
Please NOTE that there is
NO pilot hole for furniture
sliders. Please use a rubber
mallet and gently tap them
right into place.
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

⑧
⑨
⑦
D
D
⑦
⑧
⑨
⑩⑩
STEP 9
D*8
⑫
Phillips
Screwdriver
(NOT lncluded)
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

I*16
STEP 10
I
I
I
I
I
I
I
I
II
I
I
Phillips
Screwdriver
(NOT lncluded)
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

①*1 E*6 H*6
H
H
H
H
H
H
E
E
E
E
E
E
①
STEP 11
I
Phillips
Screwdriver
(NOT lncluded)
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

A*1 B*1 G*4 H*4
G
G
H
H
G
H
H
H
H
G
G
G①
NOTE: Ensure the spring points to inwards and the two
vertical frames are close to the front side of the top panel
① in this step.
STEP 12
Vertical
Frame
Front
①
Phillips
Screwdriver
(NOT lncluded)
B
A
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

H*12
STEP 13
H
HH
HH
H
Please refer to the correct
installation method, pay attention
to the gap between the upper
panel and the table legs.
You may need
assistance with
this step.
860-00427-00 Rev01
Phillips
Screwdriver
(NOT lncluded)
02 03 04 05 06 07 08 09 10 11 12 13 14 15 16