Argos Campbell Oak Effect Dining Table 280/7823 User manual

Campbell Oak Effect Dining Table
Assembly Instructions - Please keep for future reference 280/7823
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
Issue 1 - 29/07/14
Dimensions
Width - 117cm
Depth - 76.5cm
Height - 74cm

• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Unit weight: 22.12 kgs.
1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.

2
Components - Parts
Components - Fittings
Please check you have all the parts listed below
Please check you have all the fittings listed below
Top panel
(117 x 76.5 x 1.8cm)
M6 x 25mm Bolt x 16
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
1Long side panel x 2
(112.5 x 8 x 1.8cm)
2
Narrow leg x 2
(72 x 8 x 1.8cm)
4L Wide leg x 2
(72 x 10 x 1.8cm)
5L
A
30mm Screw x 24
B
Dowel x 26
C
Cam bolt x 26
D
Cam lock x 26
E
Adhesive pad x 12
F
If you have damaged or missing components, call the
Customer Helpline: Argos = 0345 640 0800
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Wide leg x 2
(72 x 10 x 1.8cm)
5RNarrow leg x 2
(72 x 8 x 1.8cm)
4R
Short side panel x 2
(68 x 8 x 1.8cm)
3
Tools required
Crosshead screwdriver
Bracket x 8
G H
15mm Screw x 16

Place the panels on a flat
protected surface.
a: Attaching dowels
Insert dowels into
holes on top panel
and legs , , &
as shown.
b: Attaching cam bolts
Insert cam bolts into
holes on top panel &
wide legs & as
shown and fix using a
crosshead screwdriver.
3
Assembly Instructions
Step 1
C
C
D
D
a: b:
1
5L
5L
5R
5R
4L
4L
4R
4R
D
D
x14 C
C
C
DD
C
DC
C
DD
C
DC
C
DD
C
DC
C
C
C
C
C
D
D
C
x10
1
1
5L 5R
4L 4R 5L 5R
Step 2
1
3
3
2
2
C
D
11 1
a: b: c:
2
222
E
E
E
x14
Attaching side panels
to top panel
a: Align and insert the
dowels and cam bolt
. on top panel into
holes on the side panels
, & as shown.
b: Put the cam locks
into the holes on the
table side panels
and as shown.
c: Turn and fix the cam
locks using a
crosshead screwdriver to
lock.
C
1
2
2
3
3
D
E
E

4
Assembly Instructions
Step 2
Step 3
Securing side panels
Fix the side panels &
using screws and
tighten using a
crosshead screwdriver.
B
B
B
B
B
B
B
B
B
2
3
3
3
2
2
3 2
B
B
C
D
5L 5L 5L
a: b: c:
2
4L 4L 4L
E
E
Assembling legs
a: Align and insert the
dowels and cam bolt
. on wide legs &
into holes on the narrow
legs & as shown.
b: Put the cam locks
on narrow legs &
as shown.
c: Turn and fix the cam
locks using a
crosshead screwdriver to
lock.
C
4L 4R
5L 5R
E
E
D
4L 4R 5L
4L
EEE
5L
4L
EEE
5R
4R
EEE
5R
4R
EEE

5
Assembly Instructions
Step 4
Step 5
Attaching legs to top
panel
Position the assembled
legs , , & as
shown and align / insert
the dowels into holes
on the top panel .
C
1
4R
4L 4R 5R 5L 5R
1
5L
5L
5R
4L
4L
4R
5L
1
C
Securing legs
Fix the legs to side
panels & as shown
using bolts and tighten
using a crosshead
screwdriver.
2 3
A
4R
5R
5L
5L
5R
4L
4L
4R
3
3
2
5L 4L
A
A
AA
3
2
2

6
Assembly Instructions
Step 6
Step 7
Securing legs with
screws
Fix the legs to side
panels & as shown
using screws and
tighten using a
crosshead screwdriver.
Securing side panels
Position brackets to
side panels & as
shown and fix with
screws . Then tighten
screws using a
crosshead screwdriver.
2 3
B
4R
5R
5L
5L
5R
4L
4L
4R
3
3
2
2
4R
5R
5L
5L
5R
4L
4L
4R
3
3
2
2
Bx4
Gx2
Gx2
Gx2
Gx2 Hx4
Hx4
Hx4
Hx4
Bx4
Bx4
Bx4
5L 4L
3
2
B
BB
B
5L 4L
3
3
2
2
G
H
H
HH
H
G
G

Attaching adhesive
pads
Remove backing from
adhesive pads then
paste it on the legs &
to cover the cam
locks .
Carefully turn over the
unit.
Note: At least two
persons are required to
lift the unit.
Assembly is complete.
Assembly Instructions
Step 8
4L
4R
F
E
4R
4L
4L
4R
F
F
F
F
F
F
F
F
F
F
F
F
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
7
4
F
F