Better Homes and Gardens BH16-084-499-03 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2016-05-18 Rev. 0001-A Factory: CHEGRE
Mercer 5pc Counter Height Dining
Stock # BH16-084-499-03
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Mercer 5pc Counter Height Dining (BH16-084-499-03)
MADE IN CHINA
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware part out of reach of children.
4. Please wait until all steps are completed before tightening bolts.
5. Make sure all bolts are tightly fastened before the unit is used.
MAXIMUM LOAD 400 lb. (181.4 kg)
MAXIMUM RECOMMENDED WEIGHT LOADS
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE
MAXIMUM WEIGHTS INDICATED. USE WITH HEAVIER THAN THE MAXIMUM
WEIGHTS INDICATED MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.
GENERAL INFORMATION, TIPS & TRICKS
MAXIMUM LOAD 300 lb. (136 kg)

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Table Top (1) B- Table Apron (4)
C- Table Leg (4) D- Backrest Left Post (4)
E- Backrest Right Post (4) F- Seat Frame (4)
G- Footrest (4) H- Chair Front Leg (8)
I- Backrest Slat (8) J- Seat Panel (4)

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Ø1/4" x 5/8" Bolt (2) Ø1/4" x 1-3/4" Bolt
(92+2 extra) (32+1 extra)
(3) Lock Washer (4) Flat Washer
(92+2 extra) (92+2 extra)
(5) M6 x 15 mm Wood Screw Allen Wrench Touch-up Pen
(24+1 extra) (2) (1)
Tools required: Allen wrench (provided) and Phillips screwdriver (not provided).

5
Assembly Instructions for Table
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Position the Table Top (A) upside down on a level and protective surface.
3. Attach four Table Aprons (B) to the Table Top (A) by inserting twelve 5/8" Bolts (1) with Lock Washers
(3) and Flat Washers (4) through the metal tabs and screw into place. DO NOT fully tighten the bolts.
1
3
4
B
B
B
B
A
BB
1
3
4
DO NOT fully tighten the bolts initially until all the bolts are ready to assemble.
To avoid causing damages to the thread, DO NOT over-tighten the bolts.
Lock Washer
(12 used in this step)
③
Ø1/4" x 5/8" Bolt
(12 used in this step)
①
Flat
Washer
(12 used in this step)
④

6
Assembly Instructions for Table
4. Attach four Legs (C) to the Aprons (B) with sixteen 5/8" Bolts (1) and sixteen Washers (3 and 4).
5. Stand the unit upright and place it at the desired location.
Lock Washer
(16 used in this step)
③
Ø1/4" x 5/8" Bolt
(16 used in this step)
①
Flat
Wash
er
(16 used in this step)
④
1341
3
4
A
B
B
B
B
C
C
C
C
A
B
BC

7
Assembly Instructions for Chair
6. Combine two Backrest Slats (I) between the Backrest Left and Right Posts (D and E) with eight 1-3/4"
Bolts (2).
2
I
E
D
I
2
Ø1/4" x 1-3/4" Bolt
(8 used in this step)
②

8
Assembly Instructions for Chair
7. Attach the Seat Frame (F) and Footrest (G) to the assembled backrest with eight 5/8" Bolts (1) and eight
Washers (3 and 4).
134
1
3
4
DE
G
F
F/G
D/E
Lock Was
her
(8 used in this step)
③
Ø1/4" x 5/8" Bolt
(8 used in this step)
①
Flat
Washer
(8 used in this step)
④

9
Assembly Instructions for Chair
8. Proceed to attach the two Chair Front Legs (H) to the Seat Frame (F) and Footrest (G) with eight 5/8"
Bolts (1) and eight Washers (3 and 4).
G
F
H
H
H
D/E
1
3
4
134
Lock Washer
(8 used in this step)
③
Ø1/4" x 5/8" Bolt
(8 used in this step)
①
Flat
Washer
(8 used in this step)
④

10
Assembly Instructions for Chair
NOTE: Place a protective cover (like the bubble wrap packing material) over the carton or other support
surface to prevent from scratching.
9. Place one Seat Frame (F) upside down on the carton or other support surface, as shown.
10. Fit the notches of the Seat Panel (J) to the Backrest Posts (D and E) and fasten to the Seat Frame (F)
with six 15 mm Wood Screws (5).
11. Repeat the same process to assemble the other chairs.
15 mm Wood Screw
(6 used in this step)
⑤
F
J
J
F5

11
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
Using solvents of any kind on your furniture may damage your furniture’s finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
Check bolts/screws periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during assembly or
shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or
replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet
your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to
State.
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com

ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y MANTENGA PARA USO FUTURO.
Fecha 2016-05-18 Rev. 0001-A Fábrica: CHEGRE
Comedor Mercer de 5piezas altura de barra
Serie # BH16-084-499-03
ENSAMBLE REQUERIDO POR ADULTO
Si tiene alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne este producto a
la tienda donde lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su
instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica:
866-942-5362
Hora Estandar del Pacífico: 8:30 a.m. - 4:30 p.m. de Lunes a Viernes
O visite nuestra página de Internet 24 horas al dia, 7 días a la semana para asistencia
www.whalenstyle.com
O mande un correo electrónico a [e-mail]
LOTE NÚMERO:
FECHA DE COMPRA: / /

2
FABRICANTE: Whalen Furniture Manufacturing
CATALOGO: Comedor Mercer de 5pzas. altura de barra (BH16-084-499-03)
HECHO EN CHINA
1. Por favor, lea las instrucciones de montaje antes de ensamblar la unidad.
2. Para evitar daños, ensamble la unidad en una area limpia, nivelada y no abrasiva.
3. Mantener todas las piezas del herraje fuera del alcance de los niños.
4. Por favor, espere hasta que todos los pasos se han completado antes de apretar los tornillos.
5. Asegúrese de que todos los tornillos estén bien apretados antes de usar la unidad.
MÁXIMA CARGA 400 lb. (181.4 kg)
PESOS MÁXIMOS RECOMENDADOS
INFORMACIÓN GENERAL CONSEJOS YTRUCOS
MÁXIMA CARGA 300 lb. (136 kg)
ESTA UNIDAD DEBE UTILIZARSE CON LOS PRODUCTOS
ADECUADOS Y PESOS MÁXIMOS INDICADOS. SI SE UTILIZAN OTROS
PRODUCTOS O SE EXEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA
INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES.

3
Lista de partes y material de ferretería
Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el
ensamblado.
A- Superficie de tapa (1) B- Delantal de tapa (4)
C- Pata de mesa (4) D- Poste izquierdo (4)
E- Poste derecho (4) F- Marco de asiento (4)
G- Descanso (4) H- Pata frontal de silla (8)
I- Soporte de silla (8) J- Panel de silla (4)

4
Lista de partes y material de ferretería
Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el
ensamblado.
(1) Tornillo Ø1/4" x 5/8" (2) Tornillo Ø1/4" x 1-3/4"
(92+2 extra) (32+1 extra)
(3) Arandela de presión (4) Arandela plana
(92+2 extra) (92+2 extra)
(5) Tornillo M6 x 15 mm p/madera Llave Allen Plumón de retoque
(24+1 extra) (2) (1)
Herramienta requerida: Llave Allen (proveida) y destornillador estrella (no proveido).

5
Instrucciones de ensamble para mesa
1. Desempacar la unidad y confirmar que se tiene todo el herraje y partes requeridas.
2. Posicionar la superficie de mesa (A) boca abajo en una área limpia y nivelada.
3. Coloque cuatro delantales de tapa (B) a la superficie de la mesa (A) mediante la inserción de doce
tornillos de 5/8" (1) con arandelas de presión (3) y arandelas planas (4) a través de las lengüetas de metal
y fije en su lugar. NO apriete los tornillos completamente.
1
3
4
B
B
B
B
A
BB
1
3
4
Arandela
de
presión
(12 usados en este paso)
③
Tornillo Ø1/4" x 5/8"
(12 usados en este paso)
①
NO APRETAR completamente los tornillos al comenzar, hasta que todos los
tornillos esten listos para el ensamble. Para evitar daños a las roscas, NO APRETAR demasiado.
Arandela plana
(12 usados en este paso)
④

6
Instrucciones de ensamble para mesa
4. Adjuntar las cuatro patas de mesa (C) a los delantales de mesa (B) con dieciséis tornillos de 5/8" (1) y
dieciséis arandelas (3 y 4).
5. Poner la unidad en posición vertical y colocar en su lugar deseado.
Arandela de presión
(16 usados en este paso)
③
Tornillo Ø1/4" x 5/8"
(16 usados en este paso)
①
Arandela plana
(16 usados en este paso)
④
1341
3
4
A
B
B
B
B
C
C
C
C
A
B
BC

7
Instrucciones de ensamble para silla
6. Combinar dos soportes de silla (I) entre los postes izquierdo y derecho (D y E) con ocho tornillos
de 1 3/4" (2).
2
I
E
D
I
2
Tornillo Ø1/4" x 1-3/4"
(8 usados en este paso)
②

8
Instrucciones de ensamble para silla
7. Fije el marco del asiento (F) y el descanso (G) al respaldo ensamblado con ocho tornillos de 5/8" (1) y
ocho arandelas (3 y 4).
134
1
3
4
DE
G
F
F/G
D/E
Arandela de presión
(8 usados en este paso)
③
Tornillo Ø1/4" x 5/8"
(8 usados en este paso)
①
Arandela plana
(8 usados en este paso)
④