Touchboards ConSet 501-11 Manual

1
ELECTRIC HEIGHT ADJUSTABLE TABLE
ConSet® - TYPE 501-11 1X138H (CORNER)
DIRECTIONS FOR USE / ASSEMBLING
IMPORTANT NOTES!
Prior to installment, use and maintenance of the table frame, any installer and any user of the table must study
this assembly and operation manual carefully, so as to gain a complete understanding of its contents.
Nr. 315640.0
EN
WARNING WARNING: FAILURE TO COMPLY WITH OR OBSERVE ALL
ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS
AND WARNINGS REGARDING THE USE OF THIS
PRODUCT MAY RESULT IN SERIOUS BODILY INJURY.

2
TABLE OF CONTENT
1. SAFETY AND WARNINGS
2. USAGE
3. SET UP AND INSTALLATION
4. OPERATION
5. MAINTENANCE AND DEFECTS
6. TECHNICAL DATA
7. PARTS
8. ASSEMBLY DIRECTIONS
9. DECLARATION OF CONFORMITY
1. SAFETY AND WARNINGS
2. USAGE
The electromotive, height-adjustable tables are designed for workstations in dry work environments only.
The table height is infinitely adjustable, so that it can be set to the most ergonomically suitable working
level.
They have not been designed for other purposes than those included in this manual, e.g. they are not to
be used in areas of high humidity or dampness, nor for lifting people.
Any other use is at one’s own risk!
Do not crawl, lie or move around under the table frame, and do not sit or stand on the table
frame.
CHILDREN should only use the table when supervised by adults.
Liability: The manufacturer accepts under no circumstances warranty claims or liability claims for
damages arising from improper use or handling of the table frame other than that described in this
operation manual.
3. SET UP AND INSTALLATION
When the table has been assembled (see assembly instructions on page 3-4) the adjustable feet are
installed so that the table is level and does not shift. Then the table is connected to the 230 VAC outlet and
the table is ready for use.
Make sure that no cables can get jammed.
Place the table in a safe distance from window frames, radiators, furniture etc. so that people do not get
stuck.
Do not place any objects above 55 cm underneath the table.
When moving the table after it has been assembled, the table top needs to be removed. The table
CANNOT be lifted by the tabletop.
4. OPERATION
Operation up/down
Main power, on/off
This table complies with the prescribed safety regulations. Inappropriate use may cause damage to
persons and table.
Please read the operation manual prior to start using the table. It provides you with important
information about safety, use, installation and maintenance of the table, and thus protecting you
and your children and avoiding damage on the table.
Please guard this operation manual and pass it on to any future owner!

3
5. MAINTENANCE AND DEFECTS
The table does not require any maintenance by usage as described in chapter 2 in the directions for use.
The table is only to be maintained with a wrung cloth.
In the event of the occurrence of jarring sounds during operation, STOP using the table and please
contact the dealer.
6. TEKNISKE DATA
Frame, material and weight: Steel, silver/black - Weight of frame ~ 40 kg
B = Width:
D = Depth: Max. 120 cm
Max. 120 cm
H = Height:
V = Speed: 65 – 122 cm
~28 mm/sek.
FMAX = Max. Load on tabletop: 80 kg
Operation: Rocker switch, standby cut off
Main power:
Consumption: 220-230 VAC / 50Hz
80 Watt (standby = 0W)
7. PARTS
1b
1a 2
FMAX
W
D
H
a) x 18 b) x 6 c) x 4
3
4
5
6
2 x

4
2
3
1a 1b
2
3
5
4
8. ASSEMBLY DIRECTIONS
1
continued….
4
b) x 6
c) x 4

5
9. DECLARATION OF CONFORMITY
We hereby declare, under our sole responsibility that the following products:
-ConSet sit and stand tables product type 501-11
which are covered by this statement, are in conformity with the following standards and other normative
documents::
-Counsel Directive 98/37/EF
-Counsel Directive 89/336/EØF with later changes
-Counsel Directive 73/23/EØF with later changes
With reference to the Machinery Directive (98/37/EF) please be aware:
-the sit and stand table is considered a machine and
-the sit and stand table may not be used until it has been assembled and installed according to the
instructions.
Manufacturer:
ConSet A/S
Staalvej 14-16
DK-6900 Skjern
Denmark
Tel: [phone], Fax: [phone]
www.conset.com
[email protected]
continued…..
5
The table is now assembled. Follow the directions for use in
CHAPTER 2.
All 18 pcs. screws a) must be tightened for maximum stability.
a) x 18