Home Styles 88 5020 3071 User manual

Part List
For assembly see instructions in carton 88 5020 3072
Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
88 5020 3071
Monarch Buffet
A.
Top
1 pc.

Part List
Hardware List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
88 5020 3072
Monarch Buffet
Also need Part in carton 88 5020 3071
Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
D.
Side Panel
1 pc.
B.
Front Post
1 pc.
E.
Side Panel
1 pc.
F.
Middle Panel
1 pc.
G.
Shelf
4 pcs.
I.
Shelf
1 pcs.
J.
Front Rail
1 pc.
O.
Back Rail
1 pcs.
M.
Back Panel
3 pcs.
C.
Front Post
1 pc.
K.
Door
1 pc.
N.
Back Post
2 pcs.
L.
Door
1 pc.
Cam Lock
19 pcs.(+1 extra)
Cam Lock Screw
19 pcs.(+1 extra)
Head Cap Bolt
(short)
8 pcs. (+1 extra)
Hex Wrench
1 pc.
Wood Screw (short)
for Steel Plate
Connector
8 pcs. (+1 extra)
Small
Hex Wrench
1 pc.
Knob
2 pcs.
Machine Screw
2 pcs.
Wood Screw (short)
for Back Panel
12 pcs. (+1 extra)
Magnet
4 pcs.
Adjustable Pin
16 pcs. (+1 extra) Steel Connector
4 pcs.
Wood Screw (short)
for Magnet
8 pcs. (+1 extra)
H.
Shelf
1 pcs.
P.
Back Rail
1 pcs.
Wood Screw
6 pcs. (+1 extra)
Flat Washer
6 pcs. (+1 extra)
Head Cap Bolt
(long)
8 pcs. (+1 extra)
Steel Plate
Connector
2 pcs.

Assembly Instructions 2/5
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
* Use a soft cloth between these parts and the floor.
Figure 1
STEP 2
Attach Front Post (B) to
Side Panel (D) and Front
Post (C) to Side Panel (E)
with Cam Locks and Head
Cap Bolts (long).
D
E
J
C
F
Cam Lock
Steel Connector
STEP 1
Insert Cam Lock Screws into the pre-drilled holes of Front Posts (B)
and (C), Side Panels (D) and (E), Front Rail (J), Middle Panel (F).
(see Figure 1)
Attach Steel Connectors to Side Panels (D)
and (E) with Head Cap Bolts (long).
B
DEC
Cam Lock Screw
Head Cap Bolt (short)
Head Cap Bolt (long)
B

Assembly Instructions 3/5
M
O
MN
F
D
P
E
M
Cam Lock
STEP 4
Attach Shelf (H) to the unit with Wood
Screw, Flat Washer and Cam Locks.
Attach Front Rail (J) to the unit using
Cam Lock.
Attach Side Panel Unit (E) to the unit
using Cam Locks.
STEP 3
Attach Shelf (I) to Side Panel Unit (D) using Cam Locks.
(see Figure 2)
Attach Back Rail (P) to the unit with Wood
Screw, Flat Washer and Cam Lock.
(see Figure 3)
Attach Middle Panel (F) to the unit with Wood
Screw, Flat Washer and Cam Locks.
Attach Back Post (N) to Back Rail (P) and
slide Back Panels (M) into place.
Attach Back Rail (O) to the unit with Wood
Screw, Flat Washer and Cam Lock.
Cam Lock
Flat Washer
Wood Screw
Figure 2 Figure 3
J
I
Flat Washer
Wood Screw
H

Assembly Instructions 4/5
STEP5
Turn the unit to its’ up right position.
Attach Top (A) to unit using Cam Locks.
Insert Adjustable Pins into side panels
and middle panel. Place Shelves (G) into
position.
Attach Doors (K) and (L) to the side
panels by sliding the door lift hinges into
the side panel lift hinges. (see Figure 4)
Assemble Pull Handles to Door (J) and (K)
with Machine Screws. (see Figure 6)
Attach Magnets in position with
Wood Screws. (see Figure 5)
Insert 12x Wood Screws from the back
of the unit. (see Figure 7)
STEP 6
Figure 7
Figure 6
Figure 4 Figure 5
Wood Screw (short)
for Back Panel
K
L
G
G
G
G
A
Flat Washer
Adjustable Pin
Magnet
Wood Screw (short)
for Magnet
Head Cap
Bolt
Wood Screw
Note: Please make sure unit is level before
tightening these screws.

Assembly Instructions 5/5
STEP 7
Place the Hutch unit onto the Buffet unit.
Attach Steel Plate Connectors with Wood Screws.
(see Figure 8)
Figure 8
Steel Plate Connector
Wood Screw (short)
for Steel Plate Connector