Toyota TNS 300 User manual

TOYOTA MOTOR CORPORATIONPdf for ADPA N3LJ12/J-0-1.pdf
TOYOTA NAVIGATION SYSTEM
EINBAUANLEITUNG
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
TEILENUMMER - PART NUMBER - NUMERO DE PIECE
NAVIGATIONSSATZ
NAVIGATION KIT 08545-00805
KIT DE NAVIGATION
FÜR - FOR - POUR
**J12*L
LC 120 (LHD)

PRECAUTIONS
• Be sure to disconnect the negative (-)
lead from the battery terminals.
PLEASE READ THOROUGHLY THESE
PRECAUTIONS
FOR THIS SYSTEM INSTALLATION
• Do not pinch the rear wiring or har-
ness in the tightened part.
• When passing the wires through the
bulkhead or other panels, use a grom-
met to ensure waterproofing.
• Protect the wiring with tape when it is
passed through a hole.
waterproof - O.K.!!
Grommet
Taping
• When disconnecting the connectors,
be sure to grip the connector body.
Do not tug on the wiring.
Stop it!
• Do not forcibly pull any car wiring
harness. Rough tugging may result in
opened connections, or a broken wire
or harness.
• Confirm that lamps, horn, wiper and
other car accessories operate normal-
ly.
• Protect your car with wing covers,
seat and so on.
• Use the correct tool when tightening
bolts or nuts.
• Before drilling a hole, check that the
rear of the mounting wall is clear.
• Be sure to firmly tighten connectors
and terminals. Insert
completely
• Before connecting the power wiring to
the battery, check the wiring connec-
tions, harness, etc. to see that they
are properly secured.
• Check body and trim near area of installation to be cer-
tain no dirt or scratches resulted from the installation.
LAND CRUISER (LHD) - 2
TNS 300LAND CRUISER
INSTALLATION PRECAUTIONS
Before installing:
1. Always make sure to disconnect the (-) battery cable.
2. Place a cover on the vehicle to protect it from scratches or
damages during installation work.
Installation of parts:
1.Select a slit for installation work that does not impair opera-
tion and offers adequate comfort,
2. Always check to make sure there are no objects present on
the reverse side when drilling mounting holes.
3. When tightening parts using bolts, nuts or other fasteners on
the vehicle, never attempt to use those involved in the steer-
ing or brake systems.
4. When tightening parts, make sure not to pinch the wire har-
ness on the reverse side.
Wiring:
1. Do not pull with excessive force on the vehicle’s wire har-
ness. this can cause connectors to become disconnected or
damage to the wire harness.
2. Gather the wire harness of the vehicle together in a bundle
so that they do not hang loose, and fasten in position using
clamps.
3. Do not pass wires through locations in contact with hot parts
or parts that move in linking motion due to vibrations.
4. When passing wire through a hole, the lead wire must be
protected.
5. Make sure that connectors and terminals are securely con-
nected.
6. When handling connectors, hold onto the connector with the
connector body and do not pull on the lead wire.

TABLE OF CONTENTS
LAND CRUISER (LHD) - 3
TNS 300LAND CRUISER
REMARK :
Be sure to read the General Installation Instructions (Common Section) before installing TNS 300.
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
TNS 300 Navigation System Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
How to Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
System Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Vehicle Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
GPS Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wire Harness Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Computer Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
System Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Final Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

LAND CRUISER (LHD) - 4
TNS 300LAND CRUISER
TNS 300 NAVIGATION SYSTEM ASSY 08545-00805
4
3
2
8
9
1
5
6
7
*1
10
11
NO. Description Qty
COMPUTER 1
WIRE HARNESS 1
GPS ANTENNA 1
NAVIGATION DISC (*1) 1
COMPUTER BRACKET 2
BOLT (M5 x 8) 4
CORD CLAMP 2
FOAM TAPE 2
WIRE TIE
EARTH PLATE 1
ADHESIVE TAPE 4
5
1
2
3
4
5
6
7
8
9
10
11
*1:NAVIGATION DISC (DVD-ROM) is not included in the navigation kit.
4

LAND CRUISER (LHD) - 5
TNS 300LAND CRUISER
SYSTEM LAYOUTSYSTEM LAYOUT
Wire harness
2
Antenna cord
GPS antenna
3
Computer
1
Splicing connector (Reverse sensor wire)
Splicing connector (Speed sensor wire) Splicing connector (TX+ sensor wire)
Splicing connector (TX- sensor wire)

CONNECTION METHOD : CASSETTE TAPE PLAYER TYPE
CONNECTION METHOD : CD PLAYER TYPE
Refer to the repair manual for information on removal vehicle parts, installation methods, tightening
torque and so forth.
TNS 300LAND CRUISER
LAND CRUISER (LHD) - 6
HOW TO CONNECT
Vehicle wire harness
Splicing connector
(Speed sensor wire)
Splicing connector (TX+ sensor wire)
Splicing connector (TX- sensor wire)
Splicing connector
(Reverse sensor wire)
10P
8P
18P
1P
13P
8P
Antenna cord
GPS antenna
3
Computer
1
Cassette tape player with multi display
12P
6P
Vehicle wire harness
Splicing connector
(Speed sensor wire)
Splicing connector (TX+ sensor wire)
Splicing connector (TX- sensor wire)
Splicing connector
(Reverse sensor wire)
10P
8P
18P
1P
13P
8P
Antenna cord
GPS antenna
3
Computer
1
CD player with multi display
12P
6P

LAND CRUISER (LHD) - 7
TNS 300LAND CRUISER
Figure 1
Figure 2
Figure 3
VEHICLE DISASSEMBLY
3. Remove the ashtray.
2. Remove the integration panel (L) and
(R).
1. Remove the console finish panel (L)
and (R).
Clips x 3
Console finish panel (R)
Clips x 6
Clips x 6
Integration panel (R)Integration panel (L)
Clips x 5
Ashtray
Clips x 4
Console finish panel (L)

LAND CRUISER (LHD) - 8
TNS 300LAND CRUISER
Figure X
Figure X
Figure X
Figure 4
Figure 5
Figure 6
6. Remove the cowl side panel (R).
5. Remove the front door scuff plate (R).
4. Remove the heater control panel.
Clips x 4
Heater control panel
Bolts x 5
Hooks x 11
Front door scuff plate (R)
Hooks x 2
Nut
Cowl side panel (R)
Bolt

LAND CRUISER (LHD) - 9
TNS 300LAND CRUISER
Figure X
Figure X
Figure X
Figure 7
Figure 8
Figure 9 Screws x 5
9. Remove the glove compartment door
and instrument panel cluster moulding (R).
8. Remove the instrument panel under
cover (R).
7. Remove the passenger’s seat.
Bolts x 4
Passenger’s seat
Clips x 3
Screw
Instrument panel under cover (R)
Clips x 4
Glove compartment door
Clips x 3
Instrument panel cluster moulding (R)
Covers x 4

LAND CRUISER (LHD) - 10
TNS 300LAND CRUISER
Figure X
Figure X
Figure X
10. Remove the foot rest.
11. Remove the front door scuff plate (L).
12. Remove the cowl side panel (L).
Figure 10
Figure 11
Figure 12
Foot rest
Clips x 2
Hooks x 11
Front door scuff plate (L)
Hooks x 2
Nut
Cowl side panel (L)

LAND CRUISER (LHD) - 11
TNS 300LAND CRUISER
Figure X
Figure X
Figure X
Figure 13
Figure 14
Figure 15
13. Remove the instrument panel under
cover (L).
14. Remove the instrument panel cluster
moulding (L).
15. Remove the ignition switch bezel and
instrument panel finish lower panel.
Clips x 2
Instrument panel cluster moulding (L)
Clips x 4
Bolts x 3
Instrument panel finish lower panel
Ignition switch bezel
Clips x 2
Screw
Instrument panel under cover (L)

LAND CRUISER (LHD) - 12
TNS 300LAND CRUISER
Figure X
Figure X
Figure 16
Figure 17
16. Remove the front console panel side
cover (R).
17. Remove the meter cluster panel.
Clips x 2
Clips x 2
Meter cluster panel
Front console panel side cover (R)
Hooks x 2 Hook

LAND CRUISER (LHD) - 13
TNS 300LAND CRUISER
GPS ANTENNA INSTALLATION
Figure 18
FOAM TAPE CUT PROCEDURES
a) Cut the foam tape into 3 large
pieces, 9 middle pieces and 12 small
pieces as shown in the illustration.
8
Foam tape
8
<Large piece>
•For computer
•For computer corner cover
<Middle piece>
•For wire harness & antenna cord routing
•For extra length of reverse & speed
sensor wire
<Small piece>
•For antenna cord routing
•For reverse sensor wire routing
•For speed sensor wire routing
Figure 19
ADHESIVE TAPE CUT
PROCEDURES
a) Cut the adhesive tape into 1 large
pieces and 2 small pieces as shown in
the illustration.
11
<Large piece>
•For bracket (Adhesive tape )
<Small piece>
•For earth plate (Adhesive tape )
B
A
1. Using a knife, to cut off the weather
strip of the antenna cord .
CAUTION : Be careful not to damage
the antenna cord .
3
3
GPS antenna
3
Weather strip
Knife
Figure 20
10mm
Adhesive tape
11
x 1
x 2
x 3
x 9
x 12

LAND CRUISER (LHD) - 14
TNS 300LAND CRUISER
Figure 22
5. Route the antenna cord as shown in
the illustration.
6. Return the meter cluster to its original
position, without rubbing GPS antenna
against the instrument panel.
CAUTION : Be careful not to slip
away GPS antenna from the earth
plate .
10
3
3
3
2. Remove the release paper of the earth
plate and apply the adhesive
tape .
3. Attach the earth plate to the meter
cluster panel as shown and mount the
GPS antenna to the earth plate .
CAUTION : Make sure to clean the
installation position surface before
attaching the earth plate .
4. Fix the antenna cord using the
foam tapes .
8
3
10
10
3
10
11
10
Figure 21
Adhesive tapes x 2
11
GPS antenna
3
Earth plate
10
Antenna cord
3
Foam tapes x 3
8
GPS antenna
3
Earth plate
10
Center
Meter cluster panel
B
Meter cluster panel

LAND CRUISER (LHD) - 15
TNS 300LAND CRUISER
Figure 23
Figure 25
WIRE HARNESS INSTALLATION
2. Route the wire harness and anten-
na cord as shown in the illustration.
3
2
1. Remove the driver side J/B.
SPLICING CONNECTOR CON-
NECTION PROCEDURES
a) Remove appropriate amount of vinyl
tube or tape wrapping the vehicle side
harness to be connected.
b) Insert the vehicle harness to be con-
nected securely into the guide slit.
c) After inserting the vehicle side harness
into the guide slit, fix the splicing con-
nector, and lock it securely using a pair
of pliers or alike until the connector
clicks.
Pliers
Splicing connector
Vehicle wire harness
Figure 24
Antenna cord
3
Wire harness
2
Bolt
Nut x 2
Driver side J/B
Vehicle side tie

LAND CRUISER (LHD) - 16
TNS 300LAND CRUISER
Figure 26
Figure 27
11
Figure 28
3. Route the speed sensor wire as
shown in the illustration, and secure the
speed sensor wire using the foam
tapes .
8
2
4. Disconnect the 16P connector (White)
5. Connect the speed sensor wire (Violet /
White) of the wire harness to the
16P connector (White) terminal 11 har-
ness.
6. Reconnect the 16P connector (white) to
driver side J/B.
2
Driver side J/B
16P (White)
Foam tape x 3
8
Wire harness speed sensor wire
2
Vehicle wire harness
16P (White)
Tab
Wire harness side 16P
Wire harness speed sensor wire (Violet / White)
2
Splicing connector

LAND CRUISER (LHD) - 17
TNS 300LAND CRUISER
Figure 29
1
Figure 30
Figure 31
9. Connect the reverse sensor wire (Red /
Blue) of the wire harness to the 13P
connector (White) terminal 1 harness.
10. Reconnect the 13P connector (white) to
the connector block.
2
7. Route the reverse sensor wire as
shown in the illustration, and secure the
reverse sensor wire using the foam
tapes .
8. Disconnect the 13P connector (White).
8
2
11. Disconnect the 12P connector (White).
Wire harness reverse sensor wire (Red / Blue)
2
Vehicle wire harness
Splicing connector
13P (White)
Tab
Wire harness side 13P
12P (White)
Wire harness reverse sensor wire
2
Foam tape x 6
8
13P (White)
Connector block
Heater control panel

LAND CRUISER (LHD) - 18
TNS 300LAND CRUISER
10 9
Figure 32
Figure 33
Figure 34
15. Secure the wire harness to the vehi-
cle wire harness using the wire tie .
16. Secure the extra length of the wire har-
ness (speed sensor wire and
reverse sensor wire) as shown in the
illustration using the foam tapes .
17. Connect the wire harness 10P con-
nector (White) to the vehicle side 10P
connector (White).
2
8
2
9
2
12. Connect the TX- sensor wire (Yellow /
Black) of the wire harness to the
12P connector (White) terminal 9 har-
ness.
13. Connect the TX+ sensor wire (Yellow)
of the wire harness to the 12P con-
nector (White) terminal 10 harness.
14. Reconnect the 12P connector (white) to
the heater control panel.
2
2
18. Refit the heater control panel.
Clips x 4
Heater control panel
Bolts x 5
Wire harness TX- sensor wire (Yellow / Black)
2
Wire harness TX+ sensor wire (Yellow)
2
12P (White) Tab
Vehicle wire harness
Wire harness side 12P
10P (White)
Wire harness (speed sensor wire and reverse sensor wire)
2
Foam tapes x 2
8
Wire ties x 2
9
Bolt

LAND CRUISER (LHD) - 19
TNS 300LAND CRUISER
;;
;;
;;
;;
;
;;;;
;;;;
;;;;
;;;;
;;;;
;;
;;
Figure 35
19. Route the wire harness and anten-
na cord to the computer installa-
tion area and attach them with foam
tapes .
20. Secure the extra length of the wire har-
ness and antenna cord as
shown in the illustration using the foam
tapes .
8
3
2
8
1
3
2
Foam tapes x 7
8
Wire harness
2
Antenna cord
3

LAND CRUISER (LHD) - 20
TNS 300LAND CRUISER
Figure 37
Figure 36
COMPUTER INSTALLATION
1. Fit the computer brackets to the
computer using the bolts .
2. Attach the rest of the adhesive tapes
used to fix install the plate, to the
bottom of the computer bracket as
shown.
3. Attach the foam tape to the comput-
er as shown in the illustration.
CAUTION : Do not remove the
release paper on the under side of
the adhesive tapes yet.
11
1
8
5
11
6
1
5
Bracket installing position
Bolts x 4
6
Computer brackets x 2
5
Computer
1
Front
115mm
50mm
4. Cut the floor carpet in the computer
installation area as shown in the illus-
tration.
1
Computer
1
260mm
Computer installation area
Foam tapes x 3
8
Vehicle Slit
Adhesive tape
11 A
Adhesive tapes x 3
11
Center