Nav TV NTV-KIT553 User manual

3950 NW 120th Ave, Coral Springs, FL 33065 TEL: [phone] FAX:
561-955-9760
NNG Toyota 3/3s
Navigation System for select Toyota
NTV-KIT553/598
NTV-DOC217

NNG-Toyota 3/3s Kit Content
1. Toyota 3 or 3s GPS/Interface
2. Toyota 3 or 3s internal Modification PCB with Y-adapter
3. Audio Switching module
4. Toyota 3Plug & Play T-Harness
5. Toyota 3secondary Plug & Play T-Harness
6. Rear-LCD Harness
7.TP and LCD Harnesses
8.Optional NAV/OEM switch
9.Audio In/Out Y-Adapter
10.GPS Antenna
Year Vehicle Radio
2014-2015 Corolla, Rav4 Non-Apps, Fujitsu Ten, 6.1”
2014 Camry Non-Apps, Fujitsu Ten, 6.1”
Compatibility for NNG-Toyota 5
1
2
3
4
5
6
7
8
9
10

Toyota 3 and Toyota 3S Navigation System Installation
1 | P a g e
Toyota 3 navigation system application guide
2014 –2015 Tundra (7” Entune Plus Apps Radio)
2014 –2015 Tacoma (6.1” Entune Plus Apps Radio)
2014 –2015 Sequoia (6.1” Entune Plus Apps Radio)
2015 Avalon (6.1” Entune Plus Apps Radio)
Toyota 3S navigation system application guide
2014 –2015 Tundra (6.1” Entune non-apps Radio)
2014 –2015 Tacoma (6.1” Entune non-apps Radio)
** Toyota 3/3S navigation system only applicable to the above radios only. Please verify
the correct radio application when ordering and proceeding to installation. **
Toyota 3 7” Tundra / 6.1” Tacoma / Sequoia / Avalon (Entune Plus Apps Radio)
Toyota 3S 6.1” Tundra / 6.1” Tacoma (Entune non-Apps Radio)
DO NOT PROCEED IF YOU RECEIVE A WRONG SYSTEM. Contact your distributor for
exchange immediately. All open box / used system will void the warranty.
NTV-DOC217

Toyota 3 and Toyota 3S Navigation System Installation
2 | P a g e
WARRANTY DISCLAIMER NOTICE! Radio removal, disassembly, installation of
Navigation Electronics, and Radio re-assembly / re-installation is the responsibility of
the installer. It is recommended that you contact a professional installer that is
experienced with proper work methods involving electronics and knowledgeable of
specific procedures for radio disassembly, Navigation Electronics installation, and re-
assembly / re-installation of the Radio Head Unit in the vehicle. INSTALLATION
DAMAGE TO THE VEHICLE RADIO HEAD UNIT IS EXPRESSLY NOT COVERED UNDER
THE PRODUCT WARRANTY.
To avoid dangerous distractions that may lead to an accident, the driver should
never operate the system while the vehicle is in motion. Before installing the
product, the seller should inform the end-user of proper use and compliance with
the proper instructions and all states and federal laws.
Before beginning your installation, familiarize yourself with the installation
instructions and the Navigation system components.
CAUTION: It is advisable to disconnect the negative battery cable for 3 minutes
before beginning installation, to avoid unintended air bag deployment. Note and
record any anti-theft radio codes prior to disconnecting.
Installation
This is a general installation guide for navigation system. There will not be any
instruction on dash / radio removal. Please refer to Toyota service manual for
removing radio from dash.
*The following steps are for ALL radios types, please follow these steps
accordingly. You will be notified for specific steps later regarding Toyota 3 and
Toyota 3S system. *
NTV-DOC217

Toyota 3 and Toyota 3S Navigation System Installation
3 | P a g e
Remove screws as indicated from back and top of radio
Disconnect the (2) ribbon cables carefully Remove (4) screws from panel
before separating the radio front plate
Disconnect the (2) ribbon cables carefully Install (4) spacers provided
NTV-DOC217

Toyota 3 and Toyota 3S Navigation System Installation
4 | P a g e
Toyota 3 Installation
Connect the small touch ribbon cable to the PCB as shown. Notice the metal contacts should
be facing downward
NTV-DOC217

Toyota 3 and Toyota 3S Navigation System Installation
5 | P a g e
Connect the wide LCD ribbon cable to the PCB as shown. Notice the metal contacts should be
facing downward
Connect the factory ribbon cables to the PCB board as indicated
NTV-DOC217

6 | P a g e
Toyota 3 and Toyota 3S Navigation System Installation
Install (4) screws provided. Check all connections carefully
Connect the LCD/TP harness to the PCB board as shown. Notice the metal pins are facing up
Toyota 3 dip switch setting
Dip switch 1 6 8 ON
2 3 4 5 7 OFF with factory equipped camera
Turn dip switch 1 OFF if installing after-market camera
End of Toyota 3 installation
NTV-DOC217

Toyota 3 and Toyota 3S Navigation System Installation
7 | P a g e
Toyota 3S Installation
Toyota 3S (non-apps) Radio should have the wide ribbon cable on the left side of PCB board
Disconnect the ribbon cables as shown Connect the small touch ribbon cable
NTV-DOC217

Toyota 3 and Toyota 3S Navigation System Installation
8 | P a g e
Connect the wide ribbon cable to the PCB board
NTV-DOC217

Toyota 3 and Toyota 3S Navigation System Installation
9 | P a g e
Connect the factory ribbon cables to the PCB board as shown
Install (4) screws to secure the board as shown
Toyota 3S dip switch setting
Dip switch 1 ON
2 3 4 5 6 7 8 OFF with factory equipped camera
Turn dip switch 1 OFF if installing after-market camera
End of Toyota 3S Installation
NTV-DOC217

Toyota 3 and Toyota 3S Navigation System Installation
10 | P a g e
Run the LCD/TP harness as shown through the radio chassis
Trim the radio cover as shown
Harness exit as shown
NTV-DOC217

Toyota 3 and Toyota 3S Navigation System Installation
11 | P a g e
Refer to previous page for system wiring connections
Connect GPS Antenna to GPS Module (best GPS Antenna location is under passenger side A-
pillar cover, on top of dash)
Test system thoroughly before re-assemble of the radio and dash
Test reverse camera function
Test driver side speaker integration function (mute and voice from navigation software)
NTV-DOC217

Toyota 3 and Toyota 3S Navigation System Installation
12 | P a g e
FAQ
Please follow all the steps in this installation manual, failure to do so might
void the product warranty and damage the factory radio
Power
GPS Module has (2) led lights as indicators when system is power on.
Both led lights should lit with good power. If any of the light is
dimmed, you should check for B+ and ACC power sources.
Display
No Display
1. There are two led lights at the GPS module to indicate data
and power. If led lights are OFF and radio is ON, check the
power fuse inside the black box from the main harness
2. Check all wiring connectors for any loose connection
3. Check all wiring shielding for any damage during the
installation process
4. Check all wiring for any type of damage
5. Check PCB ribbon cables for loose, misalignment, or
damage
No Touch Response
1. Check both Radio mode and NAV mode for touch responses
2. Check led lights for power and data indications
3. Check 2in1 TP/LCD IN cable for any loose connection, or
damage
4. Check PCB ribbon cables for loose, misalignment, or
damage
No GPS software loaded, touch screen alignment screen occurred
Check map SD card at GPS module, see any sign of missing,
loose, pop-out, misalignment, or damage
Sound
1. Check all cable for connections to Audio Box for loose, or damage
2. Check software volume settings, ensure volume is not muted
3. Check connections at radio for loose, damaged wires
NTV-DOC217