TP-Link Archer AX11000 User manual

Connect the Hardware
Congure the Router
Method ONE: Via TP-Link Tether App
1. Download the Tether app.
Scan for Tether Tether
or
Method TWO: Via a Web Browser
1. Connect your device to the router wirelessly
or with an Ethernet cable.
2. Launch a web browser, and enter
http://tplinkwifi.net or http://192.168.0.1 in
the address bar. Create a password to log in.
3. Follow the step-by-step instructions to
set up the internet connection and
register for the TP-Link Cloud service.
Note: If the login window does not appear, please refer to
Q1 of Need Help? in this guide.
Internet
Connect the powered-off modem
to the router’s 2.5 Giga WAN port
with an Ethernet cable.
Power on the modem, and then wait about
2 minutes for it to restart.
Connect the power adapter to the
router and turn on the router.
Verify the LED on the top is solid on (red or white) before moving on.
Choose your device type
Archer AX11000
Archer C5400X
Range Extender
Router
3. Tap the button in the Tether app and
select Archer AX11000. Follow the steps
to complete the setup and connect to
the internet.
If your internet connection is through an Ethernet cable directly from the wall instead of through a DSL /
Cable / Satellite modem, connect the Ethernet cable to the router’s 2.5 Giga WAN port, and then follow
steps 3 and 4 to complete the hardware connection.
*Image may dier from actual product.
SSID:TP-Link_XXXX
SSID:TP-Link_XXXX_5G
SSID:TP-Link_XXXX_5G_Gaming
Wireless Password/PIN: XXXXX XXX
1
1
2
4
3
2
The default wireless network names (SSIDs) and password
are printed on the label at the bottom of the router.
2. Open the Tether app and log in with your
TP-Link ID.
Note: If you don’t have an account, create one first.
Unplug the power to turn o your modem, if any,
and remove the backup battery if it has one.
Modem
Unplug the power
Hold the antennas from the base and
push them fully into the slots.
http://tplinkwi.net
Password:
Conrm Password:
Let’s Get Started
Set up with videos:
Scan QR code or visit
https://www.tp-link.com/support/setup-video/#wi--routers

©2020 TP-Link 7106508704 REV 1.0.3
Need Help?
Q1. What should I do if I can’t access the web
management page?
Reboot your router and try again.
If the computer is set to a static IP, change its settings to
obtain an IP address automatically.
Verify that http://tplinkwifi.net is correctly entered in the web
browser. Alternatively, enter http://192.168.0.1 or
http://192.168.1.1 in the web browser.
Use another web browser and try again.
Disable and enable the network adapter in use.
Q2. What should I do if I can’t access the internet?
Reboot your modem and router, then try again.
Check if the internet is working normally by connecting a
computer directly to the modem via an Ethernet cable. If it is
not, contact your internet service provider.
Log in to the web management page of the router, and go to
Advanced > Network > Status to check whether the internet
IP address is valid or not. If it is, please run the Quick Setup
again; otherwise, check the hardware connection.
For cable modem users, log in to the web management page
of the router and go to Advanced > Network > Internet > MAC
Clone. Select Clone Current Device MAC and click SAVE.
Then reboot both the modem and the router.
Q3. What should I do if the router can’t be found via
Bluetooth in Tether (how to reset the router)?
The router's Bluetooth will be enabled for 30 minutes following a
reset to factory defaults. There are two ways to reset the router:
With the router powered on, use a pin to press and hold the
Reset button on the back of the router until the LED blinks.
Log in to the web management page of the router. Go to
Advanced > System > Backup & Restore, and click FACTORY
RESTORE. The router will reset and restart automatically.
LED & Button Explanation
Pulsing Orange
The system is starting up.
Solid Orange
The router is connected to the
internet, but the Wi-Fi is o.
Solid White
The router is working normally.
Solid Red
No internet connection.
Pulsing White
The rmware is being upgraded,
WPS connection is being established
or the router is being reset.
Wi-Fi Button
Press the Wi-Fi button to turn on or o
the wireless function of your router.
WPS Button
Press the WPS button, and
immediately press the WPS button on
your client to start the WPS process.
LED Button
Press the LED button to turn on or o
the LED of your router.
For technical support, replacement services, the user guide and
more information, please visit https://www.tp-link.com/support
If you have any suggestions or needs for our product guides, you
are welcome to email [e-mail].
To communicate with TP-Link users or engineers, visit
https://community.tp-link.com to join the TP-Link Community.
· Keep the device away from water, re, humidity or hot environments.
· Do not attempt to disassemble, repair, or modify the device.
· Do not use any other chargers than those recommended.
· Do not use damaged charger or USB cable to charge the device.
· Do not use the device where wireless devices are not allowed.
· Adapter shall be installed near the equipment and shall be easily accessible.
Quick Installation Guide
Next-Gen Tri-Band Gaming Router
AX11000