TP-Link M5350 User manual

M5350
3G Mobile Wi-Fi
REV 1.1.0
1910100018

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark
of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com

FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user‟s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user‟s authority
to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.”

CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
This device has been designed to operate with the antennas listed below, and having a maximum
gain of 5 dBi. Antennas not included in this list or having a gain greater than 5 dBi are strictly
prohibited for use with this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for
successful communication.”
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux norms CNR exemptes de licence d‟Industrie Canada. Le
fonctionnement est soumis aux deux conditions suivantes:
(1)cet appareil ne doit pas provoquer d‟interférences et
(2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
fonctionnement non souhaité de l‟appareil.
Industry Canada Statement
Complies with the Canadian ICES-003 Class B specifications.
Cet appareil numérique de la classe B est conforme àla norme NMB-003 du Canada.
This device complies with RSS 210 of Industry Canada. This Class B device meets all the
requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Korea Warning Statements:
당해 무선설비는 운용중 전파혼신 가능성이 있음.
NCC Notice & BSMI Notice
注意！
依據 低功率電波輻射性電機管理辦法

第十二條 經型式認證合格之低功率射頻電機，費經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立
即停用，并改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率
射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。
安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
●注意防潮，請勿將水或其他液體潑灑到本產品上。
●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
When there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don‟t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
This product can be used in the following countries:
AT
BG
BY
CA
CZ
DE
DK
EE
ES
FI
FR
GB
GR
HU
IE
IT
LT
LV
MT
NL
NO
PL
PT
RO
RU
SE
SK
TR
UA

TP-LINK TECHNOLOGIES CO., LTD
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: 3G Mobile Wi-Fi
Model No.: M5350
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents
ETSI EN 300 328 V1.7.1: 2006
ETSI EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.1.1:2009
EN 55022:2010
EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN 60950-1:2006+A11:2009+A1:2010+A12:2011
EN 62311:2008
The product carries the CE Mark:
Person responsible for marking this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2013

I
CONTENTS
Package Contents.......................................................................................................1
Chapter 1. Introduction.........................................................................................2
1.1 Product Overview ...........................................................................................................2
1.2 Main Features.................................................................................................................2
1.3 Physical Description .......................................................................................................2
Chapter 2. Hardware Installation..........................................................................4
2.1 Environment Requirements............................................................................................4
2.2 Hardware Installation......................................................................................................4
Chapter 3. Quick Installation Guide.....................................................................7
3.1 System Requirements ....................................................................................................7
3.2 TCP/IP Configuration......................................................................................................7
3.3 Wireless Connection.......................................................................................................7
3.4 Wizard.............................................................................................................................8
Chapter 4. Device Configuration........................................................................12
4.1 Status............................................................................................................................12
4.2 Wizard...........................................................................................................................13
4.3 SMS ..............................................................................................................................13
4.3.1 New Message ...................................................................................................13
4.3.2 Inbox .................................................................................................................14
4.3.3 Outbox...............................................................................................................15
4.3.4 Drafts.................................................................................................................15
4.3.5 SMS Settings....................................................................................................17
4.4 Advanced......................................................................................................................18
4.4.1 Dial-up...............................................................................................................18
4.4.2 Wireless ............................................................................................................24
4.4.3 DHCP Server ....................................................................................................27
4.4.4 System Tools.....................................................................................................29
Appendix A: FAQ.......................................................................................................34
Appendix B: Configuring the PC .............................................................................36
Appendix C: Specifications......................................................................................39
Appendix D: Glossary .............................................................................................. 40

M5350
3G Mobile Wi-Fi User Guide
-1-
Package Contents
The following items should be found in your package:
3G Mobile Wi-Fi M5350
One power adapter
One USB cable
One battery
Quick Installation Guide
Note:
Make sure that the package contains the above items. If any of the listed items is damaged or
missing, please contact with your distributor.
Conventions
The Device or M5350 mentioned in this guide stands for 3G Mobile Wi-Fi M5350 without any
explanation.

M5350
3G Mobile Wi-Fi User Guide
-2-
Chapter 1. Introduction
1.1 Product Overview
TP-LINK‟s M5350 is at the forefront of wireless 3G sharing. Equipped with a built-in 3G modem,
you can instantly establish your own Wi-Fi hotspot simply by inserting a 3G SIM card at the
interior of the device. With up to 21.6Mbps download and 5.76Mbps upload speeds, M5350 is
able to provide 3G wireless sharing to up to 10 users simultaneously. Its pocket-sized design
and powerful 2000mAh internal battery make it an ideal travel companion, allowing users to
work or play for hours on end. Besides, with its innovative OLED display, users can have a
much more intuitive view of the device‟s working status, such as network type (3G/1x/R) and
signal strength, network status, dial-up type, Wi-Fi status, message, battery meter, data
statistics, download and upload speed, .
1.2 Main Features
Equipped with a built-in 3G modem - No other bulky devices required
HSPA+ supported with up to 21.6Mbps download and 5.76Mbps upload speeds
Supports up to 10 users simultaneously
2000mAh internal battery for extended hours of outdoor use
Portable and cobblestone design ideal for travel use
Micro USB port for versatile recharging
OLED display provides an intuitive view of the device‟s working status
Equipped with a micro SD card slot for up to 32GB of optional storage
1.3 Physical Description
Figure 1-1 the Exterior
Figure 1-2 the Interior
Power Button
OLED Screen
Micro USB Port
SIM Card Slot
Micro SD Memory
Card Slot
RESET Button (hole)

M5350
3G Mobile Wi-Fi User Guide
-3-
The details about the Exterior and Interior are explained as below.
Power Button: When the Device is successfully installed, and it‟s powered (either by
battery or electricity); press this button for about 5 seconds to turn on the Device, and if you
want to turn it off, please press this button for another 3 seconds.
Micro USB Port: It‟s for you to connect the Device with the power adapter (attached in the
package) via the USB cable.
SIM Card Slot: It‟s where to insert your SIM card.
Micro SD Memory Card Slot: It‟s where to insert your micro SD memory card.
RESET Button (hole): It‟s the button to restore the Device to its factory defaults. With the
Device powered on, use a pin to press and hold the RESET button (hole) for about 5
seconds, until the OLED screen is off and later displays “TP-LINK”; then release the button
and wait the Device to reboot and restore its factory default settings.
OLED Screen:
Figure 1-3 OLED Screen
The OLED Indication:
Item
Description
Indication
/
Network type &
Signal strength
Indicates the current network option: 2G or 3G, and signal
strength of current network.
Network status
Indicates the successful network connection.
/
Dial-up type
Means the automatic mode of Internet connection;
Means the manual mode of Internet connection.
Wi-Fi connection
Displays the Wi-Fi status and the amount of current
wireless clients.
SMS
Indicates that there is un-read short message(s) and the
amount of un-read messages.
Battery
Displays the remaining battery power.
Download speed
Indicates the download speed of current data transmission.
Upload speed
Indicates the upload speed of current data transmission.
Data statistics
Indicates the data used in total. The data statistics will be
cleared after resetting the Device.
Table 1-1 The OLED Screen details
Note:
Pressing the power button will light up or turn off the OLED screen. When you leave alone the
buttons on the device, the OLED screen will light on for about 55 seconds and then turn off.

M5350
3G Mobile Wi-Fi User Guide
-4-
Chapter 2. Hardware Installation
2.1 Environment Requirements
Place the Device in a well-ventilated place far from any heater or heating vent
Avoid direct irradiation of any strong light (such as sunlight)
Keep at least 2 inches (5 cm) of clear space around the Device
Operating Temperature: 15℃~40℃(59℉~104℉)
Operating Humidity: 0%~75%RH, Non-condensing
2.2 Hardware Installation
STEP 1: Install SIM card and memory card.
1) Open the cover upwards (as the arrow shows).
2) Make sure to have the SIM card‟s metal chip downwards and the triangle notch outwards,
and then slide the card into its slot (in the direction as the arrow shows).
Note:
If you have a Micro-SIM or Nano-SIM, please use an adapter to convert it to a standard SIM
card.
3) First, push and then lift the locker to open it. Second, have the memory card‟s metal chip
downwards and inwards, and then fit it in its slot. Finally, put down and then pull the locker
to lock it.

M5350
3G Mobile Wi-Fi User Guide
-5-
Note:
The micro SD memory card is optional. You can purchase it appropriate to your own need.
STEP 2: Install the battery.
1) Touch the metal contacts of the battery to the metal points of the Device, and then press to
fit the battery body into the slot.
2) Before closing the cover, please note down the SSID and the wireless password on the
label for later use.
SSID: The wireless network name of M5350
Wireless Password: The pre-encryption of M5350
3) Close the cover by pressing it.

M5350
3G Mobile Wi-Fi User Guide
-6-
Note:
It‟s advised that you do not use M5350 until the battery has been installed.
When finishing the above two-step installation, you can press the power button for about
5 seconds to turn on M5350.
Tips:
You are supported to charge the battery in two ways:
Method 1:
1) Connect one end of the USB cable to the micro USB port.
2) Connect the other end of the USB cable to the USB port of the power adapter.
3) Plug the power adapter to a standard wall socket.
Method 2:
1) Connect one end of the USB cable to the micro USB port.
2) Connect the other end of the USB cable to the USB port of your PC.

M5350
3G Mobile Wi-Fi User Guide
-7-
Chapter 3. Quick Installation Guide
This chapter will guide you to quickly set up the basic functions for your M5350 3G Mobile
Wi-Fi.
3.1 System Requirements
SIM card with Internet access enabled.
Computer with wireless network card.
Web browser, such as Mozilla Firefox, Internet Explorer, Google Chrome, Apple Safari, etc.
3.2 TCP/IP Configuration
The default IP address of the M5350 3G Mobile Wi-Fi is 192.168.0.1, and the default Subnet
Mask is 255.255.255.0, which values can be changed as you desire. In this guide, we use all
the default values for description, and take the configuration in Windows XP for example. While,
Pads or Wi-Fi cellphones by default obtain IP address and DNS server address automatically,
so you can just skip this step and continue with the 3.3 Wireless Connection.
Note:
Before configuration, please make sure your computer has been equipped with a wireless
network adapter.
Obtain an IP address automatically
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.
Please refer to Appendix B: Configuring the PC for the detailed instructions.
2) Then the built-in DHCP server will assign an IP address for the PC.
Configure the IP address manually
Set up the TCP/IP Protocol manually for your PC. Please refer to Appendix B: Configuring
the PC for the detailed instructions.
3.3 Wireless Connection
Note:
To log in the Device‟s web-based management page, you need to first connect to the wireless
network of the Device.
1. Click the icon at the bottom of your desktop.
2. Click the refresh button , and then select the SSID of M5350 and then click Connect.

M5350
3G Mobile Wi-Fi User Guide
-8-
Note:
The default SSID (also called Wireless Network Name) of the device is TP-LINK_M5_XXXXXX
(XXXXXX is the last 6 characters of the device‟s MAC address).
3. Enter the wireless password you‟ve noted down in the Security Key field, and then click
OK.
Note:
You can refer to the label on the rear cover for the default SSID and wireless password of
M5350.
4. When Connected appears behind the SSID of M5350, you‟ve successfully connected to
its wireless network.
Note:
You can enjoy the 3G mobile connection instantaneously, after the device has successfully
connected to M5350 (with a SIM card inserted) and M5350‟s OLED screen displays the network
status icon . Otherwise, please continue with 3.4 Wizard to further configure your device.
3.4 Wizard
1. Open a web-browser, enter the default address 192.168.0.1 in the address field and then
press Enter. When the login window appears, enter admin (in lower case letters) for the
Password, and then click the Log in button or press the Enter.

M5350
3G Mobile Wi-Fi User Guide
-9-
Figure 3-1 Login Window
Note:
If the above screen does not pop-up, it means that your Web-browser has been set to a proxy.
Go to menu Tools > Internet Options > Connections > LAN Settings, in the screen that
appears, cancel the Using Proxy checkbox, and click OK to finish it.
2. After successful login, there will appear the Status page. Click Wizard to configure the
basic network settings for accessing network. Click Next to continue.
Figure 3-2 Wizard –Start
3. On the Dial-up Settings page shows the ISP information of the SIM card inserted. Click
Next to continue, if you are sure the information is correct. You can also click Create to
create a new profile.

M5350
3G Mobile Wi-Fi User Guide
-10-
Figure 3-3 Wizard –Dial-up Settings
4. On the Wireless Settings page, you can create a unique and easy-to-remember wireless
network name (SSID) as well as Wireless Password, or you can keep it default. Then click
Next to continue.
Figure 3-4 Wizard –Wireless Settings
5. On the Finish page, please double-check your settings. If all the parameters are verified,
click Finish to complete the Wizard; if there is anything wrong, you can click Back to
re-configure it.

M5350
3G Mobile Wi-Fi User Guide
-11-
Figure 3-5 Wizard –Finish

M5350
3G Mobile Wi-Fi User Guide
-12-
Chapter 4. Device Configuration
After the successful login to the web-based management page of M5350, you will see the main
menu listing Status, Wizard, SMS and Advanced on the top. In the following parts, these items
will be explained in details, about their respective functions and configurations.
Figure 4-1 Main Menu
4.1 Status
The Status page displays the current status information about the device. All information is
read-only.
Figure 4-2 Status
Connection Status: Displays the device‟s current connection status, including the
connection and SIM card status, Dial-up and network type, IP address, primary and
secondary DNS server.
Statistic: Displays the device‟s statistics, including current received and sent data, online
time and total data used.
WiFi Status: Displays the device‟s current wireless settings, including SSID, channel,
encryption type and current Wireless clients.
Click Data Correction to correct the accumulate data used. If the data statistics is different from
that your ISP provided, please click Data Correction button, and input the data statistics your
ISP provided to correct the accumulate data used.
Click Wireless Settings to head for the Wireless Basic Settings page and configure it.

M5350
3G Mobile Wi-Fi User Guide
-13-
Click Refresh to get the status information updated.
4.2 Wizard
Please refer to 3.4 Wizard.
4.3 SMS
Figure 4-3 SMS Menu
There are five submenus under the SMS tab (as shown in Figure 4-3): New Message, Inbox,
Outbox, Drafts and SMS Settings.Click any of them, and you will be able to configure the
corresponding functions.
4.3.1 New Message
Figure 4-4 New Message