trans BPD-502 series User manual

OVERVIEW
Low Voltage SmartDIM Daylight Sensor
BPD-502 series
INSTALLATION INSTRUCTIONS
INSTALLATION NOTES
Care must be taken when selecting the mounting location
of sensor. The ambient light level may vary greatly at
different measure points in the room, depending on the
location of the windows, lighting fixtures, wall colors, floor
material, desk top, etc.
Note the path of shadows which may affect the sensor
operation. Daylighting control may be problematic if part
of controlled area is in shadows while other part has
plentiful daylight.
The sensor is designed to measure ambient light level by
looking down from ceiling height. Sensing performance
will vary if sensor is mounted to look out from wall. Avoid
installing the sensor to directly look into the skylight, the
daylight level could easily exceed the maximum threshold
of sensor.
The ambient light level on the ceiling can be much lower
than that at the windows, corners of the room, or
especially the workplace level. Therefore, it is important to
set the optimum SmartDIM range based on the lighting
level measured over the workplace.
Avoid placing the sensor at position that will receive strong
light directly, such as within the lighting range of a
pendent light with upward lamp.
1.
2.
3.
4.
5.
The BPD-502 series member of the TRANS family is a low
voltage daylight sensor designed for automatic daylighting
control. This sensor is capable of maintaining the ambient light
level within a preset range via continuous dimming the
connected lights based on the daylight available in the space.
For the spaces with minor daylight, the sensor can also be used
to provide energy efficient automatic dimming control, thus
prevents energy waste from over lighting.
This daylight sensor employs a cutting edge digital ambient light
sensor (ALS) with an advanced SmartDIM control algorithm
developed by IR-TEC to provide a closed loop, continuous
dimming lighting control for achieving the energy efficiency
required by today’s sustainable buildings. When daylighting
level increases/decreases, the sensor will fade down/ramp up
the connected lights in a smooth way to maintain the combined
ambient light level within the preset range. The sensor will open
its isolated dry contact to shut off the lights if ambient light level
exceeds the shut-off threshold to maximize energy saving.
Like all sensors in the TRANS family, the BPD-502 series is also
available in various mounting options. This feature offers a
second-to-none design and installation flexibility for daylight
harvesting and control applications in sustainable buildings.
The BPD-502 series daylight sensor can be applied to
control the lights of areas that receive sufficient daylight,
thus the electric lights can be reduced or switched OFF
based on the daylight available in the space. Ensure that
the sensor will not receive strong light directly.
If the primary daylight source is a window, the daylight
sensor is typically mounted between the window and the
first row of fixtures.
Side-lighting area
If the primary daylight source is a skylight, the daylight
sensor should be mounted on the ceiling between the
skylight and fixtures, looking down at the floor.
Top-lighting area
SELECTING A LOCATION
AVERTISSEMENT & PRUDENCE
BPD-502 Ceiling
Light Fixture
Window
80°
Peak
Sensitivity
Typical Daylit Zone, about 12’ (3.6m)
Coupez l'alimentation au disjoncteur avant d'installer Power
Pack ou capteurs.
Ne pas installer ou couvrir une boîte de jonction ayant les classes 1
et 3 ou circuits de puissance et d'éclairage.
Classe 2 Câblage de périphériques Seulement - Ne PAS reclasser et
installer Classe 1, 3 ou alimentation et circuits d'éclairage.
Turn power OFF at circuit breaker before installing Power Pack
or Sensors.
Do Not Install To and/or Cover a Junction Box Having Class 1, 3 or
Power and Lighting Circuits
Class 2 Device Wiring Only – Do Not Reclassify and Install as Class
1, 3 or Power and Lighting Wiring
WARNING & CAUTION
P/N: 058-50200-004 Printed in Taiwanwww.irtec.com
This product may be covered by one or more U.S. patents or patent applications.
Please visit www.irtec.com for more information.
INDOOR USE ONLY
Utilisation a L'interieur Uniquement
BPD-502
Light Fixture
Skylight
80°
Ceiling

IR-TEC International Ltd. warranties this product to be free of
defects in materials or workmanship for a period of five years
from date of shipment. There are no obligations or liabilities
on the part of IR-TEC International Ltd. for consequential
damages arising out or in connection with the use or
performance of this product or other indirect damages with
respect to loss of property, revenue, profit, or cost of removal,
installation or reinstallation.
WARRANTY
SPECIFICATIONS
www.irtec.com
The BPD-502 series sensor has 5 color-coded low voltage
wires for power supply and control output connections.
Following wiring diagrams are provided for typical control
reference. Consult with a professional BMS engineer or an
IR-TEC team member if a more complex wiring diagram is
required.
WIRING DIAGRAM
The BPD-502 series can be mounted on the ceiling surface,
mounted with a 4” octagonal junction box, recess mounted
into the ceiling, or externally attached with a fixture via
various mounting brackets. For more details of available
mounting options, please refer to the mounting instructions
attached.
INSTALLATION
After the sensor is installed and correct wiring connected,
power can be applied to the sensor for operation. When
power is first applied, the sensor will measure the ambient
light level and regulate the lighting output based on the
initial SmartDIM range.
If the factory set SmartDIM range does not meet the light
level requirement, you may adjust the DIM potentiometer
(after sensor cap removed) in clockwise/countclockwise to
increase/decrease the lighting output to achieve the
desired light level. Replace the sensor cap after
adjustment, and the sensor will measure and memorize the
adjusted light level as the new range for SmartDIM control.
The connected lighting will flash 2 times in about 1 minute
after DIM adjustment to indicate the operation of new
SmartDIM setting.
OPERATION & SETTING
Power supply
Photo sensor
Current drain
Digital output
SmartDIM output
SmartDIM level
Field of view
Maximum control
Mounting height
Op. humidity
Op. temperature
Dimensions
12~24 VDC ± 5%
Digital data control ambient light sensor
15 mA typical
Isolated dry contact, max. 1A
0-10V
Manual set
Approx. 80°
50 drivers/ballasts, sink current <0.5mA ea.
2.4~3.6m (8~12 ft.)
Max. 95% RH
-40°C~55°C (-40°F~131°F)
Ø65 x H45mm (Ø2.56”x H1.77”)
DIM
DIM
(Max)
Do NOT set the SmartDIM level at nighttime or while
the space is having abundant daylight that is much
higher than optimum light level.
NOTE:
Sensor cap removed
DC power can be supplied from the driver with
auxiliary DC power output or other source.
Power Pack Control
Standalone Fixture Control
BPD-502
AO+DC+ DOGND
Black
White
Red
Red
Red Black Blue
Hot
Neut
Relay
Relay
DC24V
GND
Control
Manual
Hold ON
Hold OFF
PPU-300/301
Power Pack
DIM+
120~277 VAC
Hot
Neutral
Switch
ON: Sensor control
OFF: Manual off
DIM
N
L
BALLAST
LED DRIVER
1
DIM+
DIM
N
L
BALLAST
LED DRIVER
2
Violet White Green
BPD-502
AO+DC+ DOGND
DIM+
DIM
N
L
BALLAST
LED DRIVER
Hot
120~277VAC
Neutral
1
DIM+
DIM
N
L
BALLAST
LED DRIVER
2
Violet
Black
Red
12~24VDC
+*
*