Transition Networks SISTF1011-110-LR User manual

User’s Guide
SISTF10xx-110-LR(T)
Stand-alone industrial media converter
•Copper to fiber
• Ethernet/fast ethernet
• 10Base-T/100Base-TX to 100Base-FX
• Extended temperature
• Hazardous environment
* Typical maximum cable distance. Actual
distance is dependent upon the physical
characteristics of the network
installation.
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .7
Cable Specifications . . . . . . . . . . .9
Technical Specifications . . . . . . .11
Troubleshooting . . . . . . . . . . . . .13
Compliance Information . . . . . . .15
Part Number Port One - Copper
10Base-T/100Base-TX
Port Two - Duplex Fiber-Optic
100Base-FX
SISTF1011-110-LR RJ-45
100 m (328 ft)*
ST, 1300 nm multimode
2 km (1.2 miles)*
SISTF1012-110-LR RJ-45
100 m (328 ft)*
ST, 1310 nm single mode
15 km (9.3 miles)*
SISTF1013-110-LR RJ-45
100 m (328 ft)*
SC, 1300 nm multimode
2 km (1.2 miles)*
SISTF1014-110-LR RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
15 km (9.3 miles)*
SISTF1011-110-LRT RJ-45
100 m (328 ft)*
ST, 1300 nm multimode
2 km (1.2 miles)*
SISTF1012-110-LRT RJ-45
100 m (328 ft)*
ST, 1310 nm single mode
15 km (9.3 miles)*
SISTF1013-110-LRT RJ-45
100 m (328 ft)*
SC, 1300 nm multimode
2 km (1.2 miles)*
SISTF1014-110-LRT RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
15 km (9.3 miles)*
Extended Temperature Models: -40°C to 70°C (-40°F to 158°F)
Standard Temperature Models: 0°C to 60°C (32°F to 140°F)
Transition Networks SISTF10xx-110-LR(T) industrial
media converter connects 10Base-T/100Base-TX
twisted-pair copper cable to 100Base-FX fiber-optic
cable. The SISTF10xx-110-LR(T) is designed for
harsh industrial environments such as hazardous
locations (Class 1 Division 2/Zone 2). It includes a relay output warning alarm, and
is designed to withstand a high degree of vibration and shock. It is also available in
models that operate in either standard or extended temperature ranges.

DIN-Rail
spring
mounting
plate
Step 1: Step 2:
2
SISTF10xx-110-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Installation
DIN-rail mount
The SISTF10xx-110-LR(T) media converter includes an aluminum DIN-rail
mounting plate attached to the back panel of the converter. To mount the
converter onto a DIN-rail:
1. Insert the top of the DIN-Rail into the upper slot of the mounting plate.
The stiff metal spring should be positioned behind the DIN-rail.
2. Push down and rotate the converter to snap it into place on the DIN-rail
as shown.
Note: This device must be grounded to a well-grounded mounting
surface such as a metal plate. Install the grounding wire prior to
connecting any other device.
Ground the media converter
Grounding the device helps limit the effects of noise due to electromagnetic
interference (EMI). The grounding screw is located on the top panel next to
the terminal block.
To ground the media converter:
1. Connect one end of the grounding wire (not provided) to the grounding
screw by looping one end of the grounding wire under the star washer.
2. Tighten the grounding screw with a phillips-head screwdriver.
3. Connect the other end of the grounding wire to earth ground.
g
rounding screw
terminal block
[email protected] -- Click the “Transition Now” link for a live Web chat. 3
Installation -- Continued
CAUTION: Disconnect the media converter from the DC power source
BEFORE installing and/or wiring the device.
Install the fiber cable
1. Locate or build 100Base-FX fiber cable with male, two-stranded TX to RX
connectors installed at both ends.
2. Connect the fiber cables to the media converter as described:
• Connect the male TX cable connector to the female TX port.
• Connect the male RX cable connector to the female RX port.
3. Connect the fiber cables to the other device (another media converter,
hub, etc.) as described:
• Connect the male TX cable connector to the female RX port.
• Connect the male RX cable connector to the female TX port.
Install the copper cable
The AutoCross feature allows either straight-through (MDI) or crossover (MDI-
X) copper cable to be used when connecting devices via the RJ-45 port.
1. Locate or build 10Base-T or 100Base-TX copper cables with male, RJ-45
connectors installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on
the media converter.
3. Connect the RJ-45 connector at the other end of the cable to the RJ-45
port on the other device (switch, workstation, etc.).
Connect the fiber cable
to the media converter
as shown.
Connect the fiber cable
to the other device
(media converter,
hub, etc.) as shown
RX
TX
RX
TX
RJ-45 port
on the other device
(switch, work station, etc.)
RJ-45 port
on the media
converter

4
SISTF10xx-110-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Installation
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting the dip switches. Failure to observe this caution
could result in damage to, and failure of, the media converter.
Set the DIP switches
• The DIP switches are located on the top
panel of the media converter.
• Use a small flat blade screwdriver or a
similar device to set the switches.
NOTE: To activate the updated switch
setting, cycle the power to the media
converter.
Switch “1” set the port alarm:
ON = Enable the port alarm feature.
OFF = Disable the port alarm feature.
The port alarm feature is used to alert the user whenever a port fault
occurs. The internal relay that activates the alarm feature is connected to
the two middle contacts on the 6-contact terminal block, which is
located on the top panel of the media converter.
These two fault contacts form an open circuit when either the copper port
or the fiber port is not properly connected. Otherwise, the circuit will be
closed.
A user-supplied fault alarm device can be connected to the fault contacts.
An example would be to connect the fault contacts to a warning light
located in the control room. The light can be set up to turn on when a
fault is detected.
See page 5 for instructions on installing a port alarm device.
Switch “2” set the full/Half duplex mode ON = Full-duplex on the
100Base-FX (fiber) port:
OFF = Half-duplex on the 100Base-FX (fiber) port.
Set the fiber link to full-duplex ON when connecting the media converter
to another device that operates at full-duplex mode over fiber.
Set the fiber link to half-duplex OFF when connecting the media
converter to another device that operates at half-duplex mode over fiber.
Switch “3” currently not used.
Port
Alarm
ONOFF
not used
FDX
O
N
132
[email protected] -- Click the “Transition Now” link for a live Web chat. 5
Installation -- Continued
Install the port alarm device
A user-supplied port alarm device can be connected to the media converter to
alert the user whenever a port fault occurs. The alarm switch (#1) must be
“ON” to enable the port alarm feature (see page 4) .
The contacts for the fault alarm are on the 6-contact terminal block, located
on the top panel of the media converter. To install a port alarm device:
1. Insert the two wires from the user-supplied port alarm device into the two
terminals marked “FAULT” on the 6-contact terminal block.
2. Secure the wire by tightening the corresponding screw on the side of the
terminal block.
V2-
V1-
V1+
V2+
PWR2
FAULT
PWR1
V1, V2 INPUTS
12-48 VDC
The screws to secure
the wires are locate
d
on the side of the
terminal block.
fault contacts
6-contact terminal block
NOTE: Calculate the maximum possible current in each power wire and
signal wire. Observe all electrical codes for maximum current allowed. If
the current goes above the maximum ratings, the wiring would overheat,
causing serious damage to the network equipment.
Note the following when wiring the network:
• Signal lines must not be directly connected to outdoor wiring.
• Use separate paths to route the power wiring and the signal wiring. If
power wiring and signal wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
• Do not run signal wiring and power wiring in the same wire conduit. To
avoid interference, wires with different signal characteristics should also
be routed separately.
• Use the type of signal transmitted through a wire to determine which
wires should be kept separate. The rule of thumb is that wiring with
similar electrical characteristics can be bundled together.
• Keep input wiring and output wiring separate.
• Where necessary, label the wiring to all devices in the network.

6
SISTF10xx-110-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Installation -- Continued
Power the media converter
This device is suitable for use in Class I, Division 2, Groups A, B, C and D or
non-hazardous locations only.
WARNING: EXPLOSION HAZARD - Do not disconnect equipment
unless power has been removed or the area is known to be non-
hazardous.
WARNING: EXPLOSION HAZARD - Substitution of components may
impair suitability for Class I, Division 2.
The media converter is designed for both a primary and a backup power
supply via the 6-contact terminal block, located on the top panel of the
device. Both power inputs can be connected simultaneously to live DC power
sources. If one power source fails, the other live source acts as a backup, and
automatically supplies the converter with power.
CAUTION: Before connecting the media converter to the 12-48 VDC
power source, ensure the power source voltage is stable.
To provide PRIMARY (PWR1) power to the media converter:
1. Insert the positive (+) DC wire from the 12-48VDC power source into the
terminal marked “V1+”.
2. Insert the negative (-) DC wire into the terminal marked “V1-”.
3. Secure the wires by tightening the corresponding screws on the side of
the terminal block.
To provide BACKUP (PWR2) power to the media converter:
1. Insert the positive (+) DC wire from the 12-48VDC power source into the
terminal marked “V2+”.
2. Insert the negative (-) DC wire into the terminal marked “V2-”.
3. Secure the wires by tightening the corresponding screws on the side of
the terminal block.
V2-
V1-
V1+
V2+
PWR2
FAULT
PWR1
V1, V2 INPUTS
12-48 VDC
The screws to secure
the wire are located
on the side of the
terminal block.
backup power
contacts
p
rimary power
contacts
6-contact terminal block
Operation
LED status
Use the status LEDs to monitor the SISTF10xx-110-LR(T) media converter
operation in the network.
The three LEDs near the top indicate the power and fault status:
PWR1 (amber) ON = Primary power is connected to the media
converter.
PWR2 (amber) ON = Backup power is connected to the media
converter.
FAULT (red) ON = (If the port alarm switch
(#1) is on) the media
converter lost either the fiber
link or the copper link.
If the port alarm switch (#1) is
off the FAULT LED will remain
off, even in the event of a loss
of a link.
The two lights near the fiber port indicate the fiber
(100Base-FX) link status:
100M (green) ON = Fiber link is active.
flashing = Data is being
transmitted over the fiber link.
FDX/COL (green) ON = Fiber link is in full-
duplex mode.
flashing = Collisions are
occurring.
OFF = Fiber link is in half-
duplex mode.
The two lights embedded in the RJ-45 port indicate
the copper link status:
10M (green) ON = Copper link is active at
10 Mb/s.
flashing = data is being
transmitted over the copper
link at 10 Mb/s.
100M (green) ON= Copper link is active at
100 Mb/s.
flashing = data is being
transmitted over the copper
link at 100 Mb/s.
[email protected] -- Click the “Transition Now” link for a live Web chat. 7
100BASE-FX
Industrial Media Converter
10/100BASE-TX
100M
FDX/COL
100M
RX
TX
10M
PWR 1
PWR 2
FAULT

8
SISTF10xx-110-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Operation -- Continued
Features
Link Pass-Through
The Link Pass-Through feature allows the media converter to monitor both the
fiber and copper RX (receive) ports for loss of signal. In the event of a loss of
an RX signal (1), the media converter will automatically disable the TX
(transmit) signal (2), thus, “passing through” the link loss (3). The far-end
device is automatically notified of the link loss (4), which prevents the loss of
valuable data unknowingly transmitted over an invalid link.
4
1
Media
Converter A
Media
Converter B
Near-End
Device
Far-End
Device
original fault
on the copper link media converter B disables the copper lin
k
media converter A
disables the fiber TX link
3
2
media converter B
loses the fiber RX link
AutoCross™
The AutoCross feature allows either straight-through (MDI) or crossover
(MDI-X) cables to be used when connecting to devices such as hubs,
transceivers, or network interface cards (NICs). AutoCross determines the
characteristics of the cable connection and automatically configures the unit
to link up, regardless of the cable configuration. (Requires no operator
intervention.)
Auto-Negotiation
With the Auto-Negotiation feature, the media converter automatically
configures itself to achieve the best possible mode of operation over the
copper link. The media converter broadcasts its speed (10 Mb/s or 100 Mb/s)
and duplex capabilities (either full- or half-duplex) and negotiates the best
mode of operation between the two linked devices.
If the media converter is connected to a non-negotiating device over the
copper link, it will default to 10 Mb/s speed, half-duplex mode.
[email protected] -- Click the “Transition Now” link for a live Web chat. 9
Cable Specifications
The physical characteristics must meet or exceed IEEE 802.3™ specifications.
Fiber cable
Bit Error Rate: <10-9
Single mode fiber (recommended): 9 µm
Multimode fiber (recommended): 62.5/125 µm
Multimode fiber (optional): 100/140, 85/140, 50/125 µm
Standard models
SISTF1011-110-LR 1300 nm multimode
Fiber Optic Transmitter Power: min: -20.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -36.0 dBm max: -32.0 dBm
Link Budget: 16.0 dB
SISTF1012-110-LR 1310 nm single mode
Fiber Optic Transmitter Power: min: -15.0 dBm max: -6.0 dBm
Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -32.0 dBm
Link Budget: 19.0 dB
SISTF1013-110-LR 1300 nm multimode
Fiber Optic Transmitter Power: min: -20.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -36.0 dBm max: -32.0 dBm
Link Budget: 16.0 dB
SISTF1014-110-LR 1310 nm single mode
Fiber Optic Transmitter Power: min: -15.0 dBm max: -6.0 dBm
Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -32.0 dBm
Link Budget: 19.0 dB
Extended Temperature Models
SISTF1011-110-LRT 1300 nm multimode
Fiber Optic Transmitter Power: min: -20.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -36.0 dBm max: -32.0 dBm
Link Budget: 16.0 dB
SISTF1012-110-LRT 1310 nm single mode
Fiber Optic Transmitter Power: min: -15.0 dBm max: -6.0 dBm
Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -32.0 dBm
Link Budget: 19.0 dB
SISTF1013-110-LRT 1300 nm multimode
Fiber Optic Transmitter Power: min: -20.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -36.0 dBm max: -32.0 dBm
Link Budget: 16.0 dB
SISTF1014-110-LRT 1310 nm single mode
Fiber Optic Transmitter Power: min: -15.0 dBm max: -6.0 dBm
Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -32.0 dBm
Link Budget: 19.0 dB
NOTE: The fiber optic transmitters on this device meet Class I Laser
safety requirements per IEC-825/CDRH standards and comply with 21
CFR1040.10 and 21CFR1040.11.

10
SISTF10xx-110-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Cable Specifications -- Continued
Copper cable
Category 5: (minimum requirement)
Gauge: 24 to 22 AWG
Attenuation: 22.0 dB /100m @ 100 MHz
Maximum cable distance: 100 meters
• Straight-through or crossover cable may be used.
• Shielded twisted-pair (STP) or unshielded twisted-pair (UTP) may be used.
• Pins 1&2 and 3&6 are the two active pairs in an Ethernet network.
• RJ-45 Pin-out: Pin 1 = TD+, Pin 2 = TD-, Pin 3 = RD+, Pin 6 = RD-
• Use only dedicated wire pairs for the active pins:
(e.g., blue/white & white/blue, orange/white & white/orange, etc.)
• Do not use flat or silver satin wire.
Crossover Cable
1
2
3
6
Straight-Through Cable
Twisted Pair #1
Twisted Pair #1
Twisted Pair #2
Twisted Pair #2
1
2
3
6
1
2
3
6
1
2
3
6
This device is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
CAUTION: Visible and invisible laser radiation when open. Do not stare
into beam or view directly with optical instruments.
CAUTION: Use of controls, adjustments or the performance of
procedures other than those specified herein may result in hazardous
radiation exposure
[email protected] -- Click the “Transition Now” link for a live Web chat. 11
Technical Specifications
For use with Transition Networks Model SISTF10xx-110-LR(T) or equivalent
Standards: IEEE 802.3™
Data Rate: 10 Mb/s, 100 Mb/s (copper); 100 Mb/s (fiber)
Dimensions: (W x H x D) 1.8" x 5.3" x 4.1" (46 x 135 x 105 mm)
Weight: 1.4 lb. (0.63 kg) approximate
Input Power: 12-48VDC, 0.2-0.7A, 24W minimum, redundant inputs
Overload Current: 1.1 Amp with reverse polarity protection
Alarm Relay: 1Amp @ 24VDC
Max. Packet Size: 1600 bytes
MTBF: 810,000 hrs (MIL-HDBK-217F)
Mechanical: Ingress Protection: IP30
Environment: Tmra* (standard temp): 0°C to 60°C (32 to 140°F)
Tmra* (extended temp): -40°C to 75°C (-40 to 167°F)
Storage Temperature: -40°C to 85°C (-40 to 185°F)
Humidity: 5% to 90%, non-condensing
Warranty: Lifetime
*Manufacturer’s rated ambient temperature.
The information contained in this user’s guide is subject to change. For the most
up-to-date information see the user’s guide on line at: www.transition.com.
This device has been evaluated as EEx nC IIC T4 equipment under DEMKO
Certificate No. 03 ATEX 0324537U. Each module is suitable for use in Zone 2
Explosive Atmospheres. The device must be installed in a minimum IP 54
enclosure as defined in IEC 60529 and EN 60529.
This device is a building-in type. The installation into a certain end equipment
shall comply with fire enclosure request of IEC 60950/EN60950 or similar
sentence.
CAUTION: This device is intended to be supplied by a listed power unit
marked LPS or Limited Power Source, provided with a connector for field
wiring terminal, and output rated 12-48VDC, 0.2-0.7 A, 24W minimum.
CAUTION: This device is designed for operation with a safety extra-low
voltage (SELV) in compliance with IEC950 / EN60950 / VDE0805 and in
compliance with the low voltage directive 73/23/EEC and 93/68/EEC.

12
SISTF10xx-110-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Test Description Test Levels
IEC 60068-2-6 Vibration 10 - 500 - 10 Hz, 0.5 oct./min, 4g, X, Y, Z (3 axes)
IEC 60068-2-27 Shock 50 g, 11 ms, +/-X, +/-Y, +/- Z (6 direction)
IEC 60068-2-32 Free fall 75 cm, 1 corner, 3 edges, 6 faces (total 10 drops)
Environmental Type Tests
Test Description Test Levels Severity
IEC61000-4-2 ESD Air discharge +/- 8 KV 3
Contact discharge +/- 6 KV 3
ESD contact discharge +/- 6 KV 3
IEC61000-4-3 Radiated RFI Housing 10V/m, 80 MHz - 1 GHz
AM 1 KHz, 80% mod
10 V/m, 0.9 - 1.8 GHz
FM 200 Hz 50% square
3
IEC61000-4-4 Burst
(Fast Transient)
Power supply lines +/- 2 KV 3
Communication lines +/- 1 KV 3
Relay +/- 1 KV 3
IEC61000-4-5 Surge Power supply lines +/- 2 KV, 12 Ω, CM
+/- 1 KV, 2 Ω, DM
3
Relay +/- 2 KV, 12 Ω, CM
+/- 1 KV, 2 Ω, DM
3
IEC61000-4-6 Induced
(Conducted RFI)
Power supply lines 10 VAC, 150-80 MHz
AM 1 KHz, 80% mod
3
Communication lines 10 VAC, 150-80 MHz
AM 1 KHz, 80% mod
3
Relay 10 VAC, 150-80 MHz
AM 1 KHz, 80% mod
3
Technical Specifications -- Continued
EMS Type Tests
Troubleshooting
If the media converter fails, isolate and correct the fault by determining the
answers to the following questions and then taking the indicated action:
1. Is the PWR1 LED illuminated?
NO
• Ensure the power source is the proper voltage (12 - 48 VDC).
• Ensure the (+) and (-) wires from the power source are inserted
properly in the terminal block contacts labeled “PWR1”.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 2.
13
[email protected] -- Click the “Transition Now” link for a live Web chat.
Troubleshooting -- continued
2. Is the PWR2 LED illuminated?
NO
• Ensure the power source is the proper voltage (12 - 48 VDC).
• Ensure the (+) and (-) wires from the power source are inserted
properly in the terminal block contacts labeled “PWR2”.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 3.
3. Is the FAULT LED illuminated?
YES
• If the port alarm switch (#1) is on, the media converter lost the fiber
link or the copper link.
• Check the fiber cables and the copper cables for proper connection.
NO
• Proceed to step 4.
4. Is the 100M LED illuminated?
NO
• Check the fiber cables for proper connection.
• Verify that the TX and RX cables on the media converter are
connected to the RX and TX ports, respectively, on the other device.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 5.
5. Is the 100M LED flashing?
NO
• If there is no activity on the fiber port, contact Tech Support.
• If there is activity on the fiber port, disconnect and reconnect the
fiber cable to restart the initialization process.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 6.
6. Is the FDX/COL LED illuminated?
YES
• The media converter has selected full-duplex mode for the fiber link.
• If the mode is not correct, disconnect and reconnect the fiber cable
to restart the initialization process.
• Proceed to step 7.
NO
• The media converter has selected half-duplex mode for the fiber link.
• If the mode is not correct, disconnect and reconnect the fiber cable
to restart the initialization process.

14
SISTF10xx-110-LR(T)
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Troubleshooting -- Continued
• Proceed to step 7.
7. Is the FDX/COL LED flashing?
YES
• Collisions are occurring on the fiber link. Disconnect and reconnect
the fiber cable to restart the initialization process.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
NO
• Proceed to step 8.
8. Is the 10M LED (on the RJ-45 port) illuminated?
YES
• The media converter has selected 10 Mb/s for the twisted-pair link.
• If the speed is not correct, disconnect and reconnect the twisted-pair
cable to restart the initialization process.
• Proceed to step 9.
NO
• Proceed to step 9.
9. Is the 100M LED (on the RJ-45 port) illuminated?
YES
• The media converter has selected 100 Mb/s for the twisted-pair link.
• If the speed is not correct, disconnect and reconnect the twisted-pair
cable to restart the initialization process.
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
NO
• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.
Contact Us
Technical support
Technical support is available 24 hours a day
US and Canada: 1-800-260-1312
International: 00-1-952-941-7600
Transition now
Chat live via the Web with Transition Networks Technical Support.
Log onto www.transition.com and click the Transition Now link.
Web-based seminars
Transition Networks provides seminars via live web-based training.
Log onto www.transition.com and click the Learning Center link.
Declaration of Conformity
Name of Mfg: Transition Networks
6475 City West Parkway, Minneapolis MN 55344, U.S.A.
Model: SISTF10xx-110-LR(T) Series Media Converters
Part Number(s): SISTF1011-110-LR, SISTF1012-110-LR, SISTF1013-110-LR,
SISTF1014-110-LR, SISTF1011-110-LRT, SISTF1012-110-LRT,
SISTF1013-110-LRT, SISTF1014-110-LRT
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the
S ISTF10xx-110-LR(T) to which this declaration refers
is in conformity with the following standards.
EN 55022:1998 Class A; FCC Part 15 Subpart B; 21CFR subpart J;
UL 60950; UL 508; CSA C22.2 no 60950; EN 60950;
UL/cUL Class 1, Div 2, Groups A, B, C, D; ATEX Class 1, Zone 2, EExnC IIC;
EN61000-4-2, -4-3, -4-4, -4-5, -4-6; IEC 60068-2-6, -2-27, -2-32
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
[email protected] -- Click the “Transition Now” link for a live Web chat. 15
Contact Us -- continued
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff.
[email protected]
Address
Transition Networks
6475 City West Parkway
Minneapolis, MN 55344, U.S.A.
Telephone: [phone]
Toll free: 800-526-9267
Fax: [phone]
NOTE: The following part numbers are UL listed: SISTF1011-110-LR, SISTF1011-110-
LRT, SISTF1013-110-LR, SISTF1013-110-LRT, SISTF1014-110-LR, SISTF1014-110-LRT.
Compliance Information
UL Listed, C-UL Listed (Canada)
CISPR22/EN55022 Class A, CE Mark
FCC regulations
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to correct the
interference at the user's own expense.
NOTE: The following part numbers are UL listed: SISTF1011-110-LR, SISTF1011-110-LRT,
SISTF1013-110-LR, SISTF1013-110-LRT, SISTF1014-110-LR, SISTF1014-110-LRT.
May 5, 2006_____
Stephen Anderson, Vice-President of Engineering Date

Compliance Information -- continued
Canadian regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus
set out on the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des Communications du Canada.
European regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb
dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für
Gegenmaßnahmen verantwortlich.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer
des interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures
spécifiques appropriées.
Trademark Notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright Restrictions
© 2004 Transition Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any
means - graphic, electronic, or mechanical - without written permission from Transition
Networks.
Printed in the U.S.A. 33309.C
In accordance with European Union Directive 2002/96/EC of the European
Parliament and of the Council of 27 January 2003, Transition Networks will
accept post usage returns of this product for proper disposal. The contact
information for this activity can be found in the 'Contact Us' portion of this
document.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-
Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der
Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über
Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer
Konformität.