TransLite TL-MC93 User manual

TL-MC93 WI-FI ROUTER WITH 1G MOCA 2.0 NETWORK ADAPTOR
www.transliteglobal.com 1 | P a g e
TRANSLITE GLOBAL, LLC
Product Overview
TL-MC93 Wi-Fi Router with 1G coax adaptor can be interlinked with any networking device at your home, by
transmitting Ethernet signal and video signal in one single coax cable.
Complied with MoCA2.0 standard, having 1400Mbps PHY layer and 1000Mbps MAC layer transmission rate, respectively.
Up to 16 adaptors can communicate with each other at the same time.
 Fast 802.11ac/n Wi-Fi wherever you need it
 Dual bandconcurrent radio for wirelessthroughputupto 1167Mbps
2x2 802.11ac 5 GHz solution
2x2 2.4 GHz radio
Specifications
Parameter
Value
Chip technology
MoCA2.0 Bonded
Support protocols
IEEE802.3, IEEE802.3x, IEEE802.3u etc.
Modulation
OFDM, TDMA/TDD
Channel Bandwidth
100 MHz
Operating Frequency Band
975-1125 MHz, 1150-1500 MHz
Max. Attenuation
75 dB
PHY Data Rate
1400 Mbps
MAC Data Rate
1000 Mbps
Encryption
128-bit AES
Number of Ethernet Ports
1-4 Ports
Gigabit Ethernet Port
10/100/1000 Mbps
Power Supply
DC 12V/2A
Power Consumption
<5 W

AC WIRELESS ROUTER WITH BONDED MOCA
TRANSLITE GLOBAL, LLC
AC Wireless Router
with Bonded
MoCA
User Guide

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 1 | P a g e
TRANSLITE GLOBAL, LLC
TableofContents
Table of Contents 1
Introduction 3
Features 4
Getting to Know the Router 5
Front Panel 5
Back Panel 6
Installing the Router 7
Connecting the Router 7
Connect to Internet with Better Wi-Fi 9
Accessing the Router’s GUI 10
Wireless Setup 10
Wireless Security 12
WPS 13
Advanced Wireless Setup 14

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 2 | P a g e
TRANSLITE GLOBAL, LLC
MoCA Setup 14
Specifications 15
Notices 17
Warranty 17
Important Safety Instructions 18
FCC Class B Equipment 19
Important Note on Wi-Fi 20
Technical Support 20

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 3 | P a g e
TRANSLITE GLOBAL, LLC
Introduction
The is a wireless network router with dual concurrent radios
supporting both 2.4GHz and 5GHz operation in 802.11 a/b/g/n,
and also 5GHz in 802.11ac. This allows the Router to connect to
everything from legacy wireless laptops, computers, and
gaming platforms, up to the most current (and future) Apple
and Android tablets, laptops, media platforms, and
smartphones.
The Router works by being placed in a central location of the
home, or in a location where the existing wireless signal is
weak, and then being physically connected directly to your
gateway/modem.
This physical connection extends the Wi-Fi signal.
For users with newer mobile devices, tablets, and laptops,
connections through the 5GHz radio can markedly increase the
performance and speed of your Wi-Fi connection, while freeing
up the 2.4GHz band for legacy or older devices.

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 4 | P a g e
TRANSLITE GLOBAL, LLC
Features
 Fast 802.11ac/n Wi-Fi wherever you need it
 Upgrade to 802.11ac speeds without replacing your router
 Dual bandconcurrent radio forwirelessthroughputupto1167Mbps
 2x2 802.11ac 5 GHz solution
 2x2 2.4 GHz radio
 Bonded MoCA 2.0
 Two gigabit Ethernet ports
 WPA2, WPA security with AES encryption
 Wi-Fi Protected Setup (WPS)

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 5 | P a g e
TRANSLITE GLOBAL, LLC
Getting to Know the Router
This chapter describes the location and uses of the Router’s LEDs,
ports, and buttons.
FrontPanel
The front panel features LEDs that illuminate green when power,
available ports, and/orwirelessbandsarefunctioningandinuse.
Power
Coaxport
(Red: Bonded Speed) (Green: 2.0/1.1 Speed)
Ethernet port 2
Ethernet port 1
5GHz radio
2.4GHz radio

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 6 | P a g e
TRANSLITE GLOBAL, LLC
BackPanel
 Power port : used to connect the power adapter (external, 12V DC, 2A)
to the Router.
 Coax port : used for connecting the Router to a coaxial network,
using Bonded MoCA 2.0.
 Dual-portGigabitEthernetswitch :usedfordirectlyconnecting
the Router to the gateway/modem.
 Labels: indicate the factory default GUI access username and
password, network SSID names, and security keys.

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 7 | P a g e
TRANSLITE GLOBAL, LLC
InstallingtheRouter
There are two parts to installing a Router: placing and connecting the
Router and connect to Internet with Better Wi-Fi.
ConnectingtheRouter
Now that the Router is synced with the gateway/modem’s wireless
network, it can be connected to the gateway/modem’s MoCA
network and placed in another area or room of the home/office. To
do this:
Place the Router in an area where the Wi-Fi signal is weak or
spotty. A coaxial outlet must be available nearby.
1. Connect the included coaxial cable into the Coax port on the
rear panel of the Router.
2. Connect the other end of the coaxial cable into the nearby
coaxial outlet.
3. Plug the Router’s power adapter into the Power port of the
Router, and the other end into an electrical wall outlet.
4. If applicable, connect an Ethernet cable between one of the Router’s
LAN ports and the Ethernet port of a non-wireless device (wireless
devices will connect via the wireless network). The configuration
should look similar to the figure, below:

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 8 | P a g e
TRANSLITE GLOBAL, LLC
5. Wait until the Coax and Wireless LEDs on the front panel of the
Router glow green (MoCA 2.0/1.1 Speed) or red (Bonded MoCA 2.0
Speed). This may take a few minutes.
If the Coax Light does not turn Green/Red, make sure that your
gateway/modem supports MoCA.
The Router is now synced, installed, and extending the gateway/
modem’s wireless network in a previously weak area.

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 9 | P a g e
TRANSLITE GLOBAL, LLC
Using a Coaxial Splitter
If another device is using the coaxial outlet needed from step 3 in the
previous procedure, perform the following steps:
1. Disconnect the coaxial cable from the coaxial outlet.
2. Connect a coaxial cable between the coaxial outlet and the single
port on a two-way coaxial splitter.
3. Connect the coaxial cable disconnected in step 1of this procedure
to oneof the dual ports onthe splitter.
4. Connect a coaxial cable between the Coax port of the Routerand
the other dual port on the splitter.
The final configuration should be similar to the inset in the figure on
the previous page.

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 10 | P a g e
TRANSLITE GLOBAL, LLC
Connect to Internet with Better Wi-Fi
1. Get a device and make sure that it is connected to the Wi-Fi Network
Extender wirelessly.
You can find the Router’s Wireless Network Name and Password by looking at
the label on the back of the Extender.
If you would like to manual change the Router’sWireless Network Name and/or
Password:
a) Use a laptop, tablet or other device to login into your Wi-Fi Router
b) Find a device with the name TL-2.4G.
c) Open a web browser, and type the IP address located at the
back of your device.
d) Once the Home Screen appears, login into the Router w i t h the
user name admin and password admin
e) Click on the Wireless Settings / Wireless2 Settings icons.
f) Click on the Basic icon to change the Wireless Network Name
g) Click on the Security icon to change the Password

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 11 | P a g e
TRANSLITE GLOBAL, LLC
Accessing the Router’s GUI
The Router features an onboard graphical user interface (GUI) that
includes user-configurable settings. Some of these settings should be
accessed by experienced network technicians only.
To configure the network settings of the Router:
1. Ensurethatthe Router is connectedto a gateway/modem’sMoCA
coaxial network, and that both devices are powered on.
2. Use a laptop, tablet or other device to login into your Wi-Fi Router
3. Find a device with the name TL-2.4G.
4. Open a web browser, and type the IP address located at the back of
your device.
5. Once the Home Screen appears, login into the Router with the user
name admin and password admin
Wireless Setup
Wireless settings can be accessed from the menu on the left side. These
settings configure various aspects of the Router’s wireless network, and
the majority of them should be adjusted by an experienced network
technician only. The exceptions are the settings contained in the Basic
Setup screen.

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 12 | P a g e
TRANSLITE GLOBAL, LLC
BasicSetup
The Basic Setup wireless network screen contains various settings
regarding the Router’s wireless network. When finished
adjusting the settings in this s creen,click Apply .
Radio On/Off
This option turns the Router’swirelessradioonand off.
Broadcast Network Name (SSID)
This option controls whether or not the name of the network is broadcast to
other wireless devices (usually, in the device’s available wireless network
list). Select Enable or Disable by clicking in the appropriate radio button.

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 13 | P a g e
TRANSLITE GLOBAL, LLC
Wireless Band
This option allows the user to select the bandwidth at which the
Router’s wireless radio will operate.
Network Name (SSID)
Enter the name of the wireless network in this text box.
Channel Bandwidth
This option allows the user to select the channel width at which the
Router’s wireless radio will operate. We recommend using the
default setting.
Wireless Security
The Wireless Security screen allows the user to apply wireless security
to the Router’s wireless network. This screen should be accessed by
experienced network technicians only.
Security Mode
This option allows the user to select the type of security applied to the
Router’swirelessnetwork.
PassPhrase
This option allows the user to enter a custom password phrase or value.

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 14 | P a g e
TRANSLITE GLOBAL, LLC
WPS
The WPS screen allows the Router to accept wireless clients via Wi-Fi
Protected Setup (WPS), an automatic wireless network connection
protocol. Only experienced network technicians should configure the
settings in this screen.

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 15 | P a g e
TRANSLITE GLOBAL, LLC
Advanced Wireless Setup
Only experienced network technicians should configure the settings
in this screen.
MoCA Setup
The adapter has software for the MoCA Management.
The settings the user to configure various options for the Extender’s
coaxial connection.
They should be adjusted by an experienced network technicians
only.
Please contact us by email: [e-mail]

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 16 | P a g e
TRANSLITE GLOBAL, LLC
Specifications
Protocol/Standards/Support
Wireless IEEE 802.11ac
EthernetIEEE802.3/802.3u/802.3ab10/100/1000Base-T MoCA
1.0/1.1/2.0
LANInterfaces
Two 10/100/1000 Ethernet
One MoCA 2.0 bonded Coaxial Jack
LED Indicators
Power, Coax, Wi-Fi 2.4 GHz, Wi-Fi 5 GHz, LAN Ethernet 1, LAN
Ethernet 2
Antennas
2x2 : internal 2.4 GHz
2x2 : internal, 5 GHz

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 17 | P a g e
TRANSLITE GLOBAL, LLC
Power Adapter
Input100-240VAC@0.8A
Output 12Vdc @ 2A
Regulatory
FCC, UL
Wi-Fi,WPS
RoHS
Environmental
Operatingtemperature -0ºCto40ºC(32ºFto104ºF)
Storagetemperature -0ºCto70ºC(32ºFto158ºF)
Operatinghumidity -10%to85%non-condensing
Storagehumidity -5%to95%non-condensing
Altitude :-197 ft. to 7000 ft.
Note : Specifications are subject to change without notice.

AC WIRELESS ROUTER WITH BONDED MOCA
www.transliteglobal.com 18 | P a g e
TRANSLITE GLOBAL, LLC
Important Safety Instructions
Basic safety precautions should always be followed to reduce the risk of fire,
electrical shock,andpersonalinjury, includingthe following:
 Do not use this product near water – for example, near a bathtub,
kitchen sink, laundry tub, or swimming pool, or in a wet
basement; only clean with dry cloth.
 Do notblockanyventilationopenings.Installinaccordancewiththe
manufacturer's instructions. Do not install near any heat sources
such as radiators, heat registers, stoves, or other apparatus
including amplifiers that produceheat.
 Do not use the telephone to report a gas leak in the vicinity of
the leak.
 Use only the power cord indicated in this manual if applicable.
Coaxial Cable
If applicable, the coaxial cable screen shield needs to be connected to the
Earth at the building entrance per ANSI/NFPA70, the National Electrical
Code (NEC), in particular Section 820.93, “Grounding of Outer Conductive
Shield of a Coaxial Cable,”or in accordance with local regulation.