Transmitter Solutions DOLKSS1KB User manual
VERSION: 170318_V1
DOLKSS1KB
Programming & Installation Manual
FOR ELECTRIC LOCK INSTALLTION
SELF-CONTAINED
DIGITAL ACCESS CONTROL KEYPAD
2480 South 3850 West, Suite B
Salt Lake City, UT 84120
(866) 975-0101 • (866) 975-0404 fax
www.transmittersolutions.com
TABLE OF CONTENTS
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
STANDARD PROGRAMMING SUMMARY CHART
SETTING & PROGRAMMING
SET KEYPAD TO SINGLE USER MODE (to whom it may require)
SPECIFICATIONS
APPLICATION EXAMPLE
AUXILIARY INFORMATION
······························································································································· 3
······················································ 3-7
················································································································· 4
························································································································· 5
··········································································· 5
·········································································· 6-8
······································································································ 9-26
············································································································· 9
····························································································· 9
············· 9
······························································································ 10
··················································································· 10
······································································································· 11
························································································ 12-13
··································································································· 14
·············································································· 15
········································································ 16-17
·················································································· 18
················································································ 19
······································································································ 20
··················································································· 20
·················································································································· 21
································································································ 21
·········································································································· 22-23
·············································· 24-25
··························································· 24-25
·········································································· 25
······························································································································ 26
················································································································· 27
············································································································· 28
2
TABLE OF CONTENTS
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
STANDARD PROGRAMMING SUMMARY CHART
SETTING & PROGRAMMING
SET KEYPAD TO SINGLE USER MODE (to whom it may require)
SPECIFICATIONS
APPLICATION EXAMPLE
AUXILIARY INFORMATION
······························································································································· 3
······················································ 3-7
················································································································· 4
························································································································· 5
··········································································· 5
·········································································· 6-8
······································································································ 9-26
············································································································· 9
····························································································· 9
············· 9
······························································································ 10
··················································································· 10
······································································································· 11
························································································ 12-13
··································································································· 14
·············································································· 15
········································································ 16-17
·················································································· 18
················································································ 19
······································································································ 20
··················································································· 20
·················································································································· 21
································································································ 21
·········································································································· 22-23
·············································· 24-25
··························································· 24-25
·········································································· 25
······························································································································ 26
················································································································· 27
············································································································· 28
2
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
DOLKSS1KB is a self-contained digital access control keypad that offers field proven reliability and
cost effec�ve solu�ons for residen�al and commercial installa�ons. It is designed for stand alone
electric lock opera�ng with 12V DC power supply. It employs a 3 Amp Solid State output contact
and is virtually compa�ble with any Fail-safe or Fail-secure electric locking device.
INTRODUCTION
DK-9521 / DK-9522 is an universal, self-contained digital access keypad offers field proven reliability and cost
effective solutions for residential and commercial installations. It is designed for stand alone electric lock and inter-
lock systems and operates from a 12 to 24V AC/DC power supply and virtually compatible with any electric locking
device. Apart from that it is also the perfect choice for controlling security systems, automatic operators and
machinery. The DK-9521 offers single relay output, and that the DK-9522 offers dual relay output.
DK-9521 / DK-9522 consists two application softwares of Single User Mode for the general Users, and Multi-User
Mode for the advanced Users. The system offers a 4 digit length user code with 10,000 combinations for each
output in single user mode; and 100 user codes for output 1 and 10 user codes for output 2 in length of 4-8 digits
with combinations of more than 100 million in multi-user mode. Operation options of Auto Code entry and Manual
Code entry are available in both two user modes. Programmed information that stored in the system are non-volatile
in power failure.
Normally Closed contact while the keypad is secured on the box. It is open while keypad is separated from the
box. Connect this N.C. terminal to the 24 hour zone of an alarm system if necessary.
Connect to 12-24V AC or DC power supply. The ( ) supply and ( ) GND are the common grounding points of
the keypad system. No selection jumper is required for the full input voltage range.
Connect DC power with the (+) and ( ) polarity indicated; and there is no polarity discrimination for AC power
input.
5 Amp relay dry contacts, recommended for door strike controls. Normally Open (N.O.) and Normally Closed
(N.C.) outputs are available. Use N.O. output for Fail-secure locking device and N.C. output for Fail-safe locking
device. The relay can be programmed in Start/Stop (toggle) mode or timer mode from 1 to 999 seconds.
N.C. TAMPER
12 24V AC/DC
OUTPUT 1
-(POWER INPUT)
- -
CONNECTION TERMINALS
2
OUTPUT
PRODUCT
DK-9521
DK-9522
OUTPUT 1
5 Amp relay
5 Amp relay
OUTPUT 2
NPN Open Collector
1 Amp relay
RELAY
1RELAY
2
ON OFF
DAP
+-
12 24V
TAMPER
N.C.
EG
IN
OUTPUT 1
N.C. C. N.O.
OUTPUT 2
N.C. C. N.O.
KEY
ACT.
DOOR
SENS
( )
GND
-DU
OUT
INT.
LOCK
O/P1
INHIB
TAMP
RELAY
ON OFF
DAP
+-
12 24V
TAMPER
N.C.
EG
IN
OUTPUT 1
N.C. C. N.O.
OUTPUT 2
N.C. C. N.O.
KEY
ACT.
DOOR
SENS
( )
GND
-DU
OUT
INT.
LOCK
O/P1
INHIB
TAMP
DK-9521 DK-9522
R
1 2 3
456
78 9
0#
RED
AMBER
GREEN
DK-9521
( ii ) Alarm System Arm-Disarm Control
Use the (N.O.) or (N.C.) output contact to make arm-disarm control of an alarm system.
Consult your alarm control panel manual for the appropriate output contact to be used in arm-disarm control.
Usually set output 2 to Momentary mode (Programming Option 501) for multi station systems and Start
/ Stop mode (Programming Option 51) for single station systems.
( i ) Shunting an N.C. Zone
Use the Normally Open (N.O.) output contact to shunt a Normally Closed (N.C.) protection zone of an
alarm system.
Set output contact to Start / Stop Mode (Programming Option 51).
19
(D) DURESS OUTPUT
(E) OUTPUT 2 (FOR DK-9522 ONLY)
ALARM CONTROL PANEL
24 HOUR N.O.
PROTECTION
ZONE
OR
1.5K
LED
+12V
LOW POWER
PIEZO BUZZER
KEY
ACT.
DOOR
SENS
( )
GND
-DU
OUT
INT.
LOCK
O/P1
INHIB
KEY
ACT.
DOOR
SENS
( )
GND
-DU
OUT
IN T.
LOCK
O/P1
INHIB
OUTPUT 2
N.C. C. N.O.
KEY
ACT.
N.C.
N.C. MAGNETIC CONTACT
TO PROTECTION ZONE
OF AN ALARM CONTROL PANEL
OR
OUTPUT 2
N.C. C. N.O.
KEY
ACT.
ALARM CONTROL PANEL
REMOTE
ARM-DISARM
CONTROL
NO. OR N.C.
INTRODUCTION
DK-9521 / DK-9522 is an universal, self-contained digital access keypad offers field proven reliability and cost
effective solutions for residential and commercial installations. It is designed for stand alone electric lock and inter-
lock systems and operates from a 12 to 24V AC/DC power supply and virtually compatible with any electric locking
device. Apart from that it is also the perfect choice for controlling security systems, automatic operators and
machinery. The DK-9521 offers single relay output, and that the DK-9522 offers dual relay output.
DK-9521 / DK-9522 consists two application softwares of Single User Mode for the general Users, and Multi-User
Mode for the advanced Users. The system offers a 4 digit length user code with 10,000 combinations for each
output in single user mode; and 100 user codes for output 1 and 10 user codes for output 2 in length of 4-8 digits
with combinations of more than 100 million in multi-user mode. Operation options of Auto Code entry and Manual
Code entry are available in both two user modes. Programmed information that stored in the system are non-volatile
in power failure.
Normally Closed contact while the keypad is secured on the box. It is open while keypad is separated from the
box. Connect this N.C. terminal to the 24 hour zone of an alarm system if necessary.
Connect to 12-24V AC or DC power supply. The ( ) supply and ( ) GND are the common grounding points of
the keypad system. No selection jumper is required for the full input voltage range.
Connect DC power with the (+) and ( ) polarity indicated; and there is no polarity discrimination for AC power
input.
5 Amp relay dry contacts, recommended for door strike controls. Normally Open (N.O.) and Normally Closed
(N.C.) outputs are available. Use N.O. output for Fail-secure locking device and N.C. output for Fail-safe locking
device. The relay can be programmed in Start/Stop (toggle) mode or timer mode from 1 to 999 seconds.
N.C. TAMPER
12 24V AC/DC
OUTPUT 1
-(POWER INPUT)
- -
CONNECTION TERMINALS
2
OUTPUT
PRODUCT
DK-9521
DK-9522
OUTPUT 1
5 Amp relay
5 Amp relay
OUTPUT 2
NPN Open Collector
1 Amp relay
RELAY
1RELAY
2
ON OFF
DAP
+-
12 24V
TAMPER
N.C.
EG
IN
OUTPUT 1
N.C. C. N.O.
OUTPUT 2
N.C. C. N.O.
KEY
ACT.
DOOR
SENS
( )
GND
-DU
OUT
INT.
LOCK
O/P1
INHIB
TAMP
RELAY
ON OFF
DAP
+-
12 24V
TAMPER
N.C.
EG
IN
OUTPUT 1
N.C. C. N.O.
OUTPUT 2
N.C. C. N.O.
KEY
ACT.
DOOR
SENS
( )
GND
-DU
OUT
INT.
LOCK
O/P1
INHIB
TAMP
DK-9521 DK-9522
1 2 3
456
78 9
0#
RED
AMBER
GREEN
( ii ) Alarm System Arm-Disarm Control
Use the (N.O.) or (N.C.) output contact to make arm-disarm control of an alarm system.
Consult your alarm control panel manual for the appropriate output contact to be used in arm-disarm control.
Usually set output 2 to Momentary mode (Programming Option 501) for multi station systems and Start
/ Stop mode (Programming Option 51) for single station systems.
( i ) Shunting an N.C. Zone
Use the Normally Open (N.O.) output contact to shunt a Normally Closed (N.C.) protection zone of an
alarm system.
Set output contact to Start / Stop Mode (Programming Option 51).
19
(D) DURESS OUTPUT
(E) OUTPUT 2 (FOR DK-9522 ONLY)
ALARM CONTROL PANEL
24 HOUR N.O.
PROTECTION
ZONE
OR
1.5K
LED
+12V
LOW POWER
PIEZO BUZZER
KEY
ACT.
DOOR
SENS
( )
GND
-DU
OUT
INT.
LOCK
O/P1
INHIB
KEY
ACT.
DOOR
SENS
( )
GND
-DU
OUT
IN T.
LOCK
O/P1
INHIB
OUTPUT 2
N.C. C. N.O.
KEY
ACT.
N.C.
N.C. MAGNETIC CONTACT
TO PROTECTION ZONE
OF AN ALARM CONTROL PANEL
OR
OUTPUT 2
N.C. C. N.O.
KEY
ACT.
ALARM CONTROL PANEL
REMOTE
ARM-DISARM
CONTROL
NO. OR N.C.
INHIBIT
(RED)
MAINS
(AMBER)
DOOR
(GREEN)
1 2 3 4 5 6 7 8
3
1 - 2 : TAMPER N.C.
3 - 4 : 12V DC --
6 - 7 : OUTPUT 1 --
Fail-Secure Electric
Lock in Default
8 - EG IN --
●
●
●
●
CONNECTION TERMINALS
4
THE LED INDICATORS
MAINS (AMBER)
DOOR (GREEN)
INHIBIT (RED)
BACK LIGHTING
THE PACIFIER TONES & THE LED INDICATING SIGNALS
NOTE:
*
**
STATUS TONES*LED SIGNALS
1. In programming mode
---
1 Beep
2 Beeps
5 Beeps
Continuous Beeps
---
1 second Long Beep **
ON
1 Flash
2 Flashes
5 Flashes
Continuous Flashes
1 Flash in 2 seconds interval
---
2. Successful key entry
3. Successful code entry
4. Unsuccessful code entry
5. DAP jumper not replaced
6. In standby mode
7. Output relay activated
DRY CONTACT
N.C.
N.O.
TRANSISTOR OPEN COLLECTOR OUTPUT
OPEN COLLECTOR
OUTPUT ----
Output switches to
ground when activated
N.O. CONTACT
OUTPUT ----
Output switches to
ground when activated
EQUIVALENT
●
●
●
●
●
●
●
AUXILIARY INFORMATION
528
A) Enter Programming Mode with Master Code (Exit-Factory Master Code: 0 0 0 0)
NOTE:
B) System Refreshing – (Default: 8 9 0 1, Mul�-user mode)
C) Code Entries –
1) Recording Master Code and User Codes – (No Default Codes)
2) Recording Super User Code – (No Default Codes)
3) Recording the Visitor Codes – (No Default Codes)
D) Configura�on of Output Modes –
(Default: Momentary, 1-second)
STANDARD PROGRAMMING SUMMARY CHART
(default=1 second)
Opera�on Time:
BASIC WIRINGS OF A STAND ALONE DOOR LOCK
NOTE:
●
●
●
●
APPLICATION EXAMPLE
TAMPER
N.C.
EG
IN
( + ) ( – )
12V DC
( + ) ( – )
DOOR LOCK
ELECTRIC LOCK
12V DC
POWER
SUPPLY
CATHODE
EGRESS BUTTON 1N4004
N.O.
(MORE EGRESS BUTTONS CAN
BE CONNECTED IN PARALLEL)
IMPORTANT NOTE:
See programming Location 66
for Fail-secure or Fail-safe
electric lock setting.
6 27
E) Configura�on of Output 1 for Electric Lock – (Default: Fail-Secure)
F) False Code Lock-up & Repor�ng – (Default: 10 tries / 30 seconds)
(default)
●Opera�on Voltage:
●Opera�on Current
●Opera�on Modes:
●User Code Combina�ons:
●Input Sensing Terminals:
●Output Contacts:
●Tamper Switch Contact:
●Auto Refreshing Time During Code Entry:
●Opera�ng Environment:
●Opera�on Temperature:
●Ambient Humidity:
●Dimensions:
●Weight:
Specifications are subject to change for modification without notice
SPECIFICATIONS
G) Output Ac�va�on (Door Open) Announcer – (Default: 1 long beep)
H) User Code Entry Modes (Auto or Manual) – (Default: Manual)
I) Pacifier Tones (Key-press beeps) – (Default: ON)
(default)
J) Main LED Flashing ON-OFF – (Default: Flashing)
(default)
(default)
(default)
726
K) Egress Delay & Warning – (Default: Instant, No warning)
(default)
L) Exit Programming Mode
2) Recording Super User Code – (No Default Codes)
3) Recording the Visitor Codes – (No Default Codes)
Opera�on Time:
Programming Examples for “Single-User Mode”
1.0 0 0 0
2.8 9 0 0
3.3 2 8 9
4.8 3 2 1output 1
5.2 5 8 0
6.2 3 0 88 hours
7.
8 25
Criteria for Programming
MUST
DO NOT
Enter and Exit Programming Mode
key.
Master Code
3. Exit the programming mode by pressing the
NOTE:
●
●
●
●
●
A) Enter Programming Mode with Master Code (Exit-Factory Master Code: 0 0 0 0)
NOTE:
B) System Refreshing to Single User Mode –
(Default: 8 9 0 0, Single-user mode)
C) Code Entries –
1) Recording Master Code and User Codes – (No Default Codes)
Programming Summary Chart for “Single-User Mode”
SET KEYPAD TO SINGLE USER MODE (to whom it may require)
Important Notes:
●
●
●
●
●
●
●“Single-User Mode”
SETTING & PROGRAMMING
DAP
ON OFF
924
Loca�on New Master Code Confirm
NOTE:
●
●
●
Programming Example :
0 0 0 0
2. Program a new Master Code 3 2 8 9 for the keypad:
NOTE:
●3 2 8 9
●
3 2 8 9
2. Enter the system refresh code and confirm with key to clear all the current stored data
except the Master Code:
NOTE:
●(default)
Programming A New Master Code (Loca�on 0 )
System Refresh (Complete Data Refresh) (Refresh Code 8901)
NOTE:
10 23
User ID Entry of Code
Output 1
NOTE:
●
●00-99
●
●
●
Programming Example :
3 2 8 9
2. Program an User Code 8 3 2 1 for output 1 ---------- One of the 100 user codes (user ID: 00-99,
taking ID = 01 as example):
Operaon (Manual Code Entry Mode)
NOTE:
●
●
Egress Modes
The Five Egress Modes:
(Default)
Programming & Operaon Examples :
3 2 8 9
Operaon
Operaon
Operaon
Egress Delay & Warning (Location 85)
1122
Loca�ons Super User Code Confirm
NOTE:
●
●
●
●Loca�on 82
Programming Example :
3 2 8 9
2. Program 2 5 8 0 as Super User Code:
Operaon :
1) Opera�ng Output 1
Programming The Super User Code (Loca�on 45)
Loca�ons Func�on Op�ons Confirm
Programming Opons:
(Default)
Pacifier Tones ON-OFF (Loca�on 83)
Loca�ons Func�on Op�ons Confirm
Programming Opons:
(Default)
Main Status LED Flashing ON-OFF (Location 84)
12 21
Loca�ons Func�on Op�ons Confirm
Programming Opons:
(Default)
2) Overriding The Door Lock Controlled by Output 1 (Keep Door Un-locked)
NOTE:
●
●
●This feature is recommended for Fail-safe locks only.
●Fail-secure lock is NOT recommended, which may be damaged by staying ac�vated for too long
due to high power consump�on.
REMARK :
is in operation to hold the door lock open, all the User Codes
including Super User Code for Output 1 are temporarily suspended.
3)
Inhibi�ng The User Codes for Output 1 (Manually Disable All User Codes for Door Lock Actua�on)
NOTE:
●
●
●
Output Ac�va�on Announcer (Loca�on 81)
Loca�ons Func�on Op�ons Confirm
Programming Opons:
User Code Entry Modes (Auto or Manual) (Location 82)
(Default)
1320
Programming Codes for Lock-Up Opons:
(Default)
Super User Code
Programming Examples:
3 2 8 9
One-Time
Time-Limit
User ID Entry of Code
NOTE:
●
●0-9
●
●
●
●
Programming Example :
3 2 8 9
2. Program a Visitor Code 1 3 7 8 at ID “0” for One-Time use:
3. Program a Visitor Code 2 3 0 8 9 at ID “1” with Time-Limit of 5 hours:
4. Program a Visitor Code 8 3 5 8 at ID “2” with Time-Limit of 10 hours:
Operaon :
14 19
Deleng Examples:
3289
a)
b)
c)
Dele�ng User Codes & Other Func�on Codes (Loca�ons 1, 45 & 47)
Loca�ons Type of Lock Confirm
Programming Codes for Type of Locks:
Important Note to Installer:
Configura�on of Output 1 for Electric Lock (Loca�on 66)
de-energized
(Default)
energized
1518
Operaon :
1. Operate Output 1 in momentary mode of 5 seconds using user code 8 3 2 1 that was programmed
previously:
----------- Output 1 operates for 5 seconds
2. Operate Output 1 in Start / Stop mode using user code 8 3 2 1 that was programmed previously:
-------- Output 1 start / stop in toggle with the same user code
3. Operate Output 1 in Start / Stop mode with the 2 digit Accelerated code using user code 8 3 2 1
that was programmed previously:
----------------- Output 1 starts with Accelerated Code
----- Output 1 stops with Full User Code
NOTE:
●The purpose of the accelerated Code -- Start / Stop mode with accelerated code can be
considered as two user codes with one for star�ng and the other for stopping the output. Owner
can give the accelerated code to the staff to start a system (for example, an alarm system). The
staff can only start the system but can not stop it. Only the owner can stop the system with the
full user code.
●The Super User Code is always valid to Start / Stop the output.
Super User Code ------- Output 1 Ac�vates or De-ac�vates
The output 1 can be programmed to trigger with the following op�ons. for a programmed length of
�me from 1 to 999 seconds; or to trigger ON and OFF in toggle with a user code; or to trigger ON
with an accelerated start code and OFF with an full digit user code.
Loca�ons Time Length Confirm
A) 1 – 999
B)
C)
D)
NOTE:
Programming Loca�ons:
●Loca�ons 40, 41, 42 and 43 for Output 1
Programming Options for Output 1 (See “Programming Summary Chart” Secon D for more informaon) :
A) Loca�on 40 : Momentary Mode with �me length from 1 to 999 seconds (Default = 1 second)
The relay outputs can be programmed to work for a �me length from to seconds to
cope with the door opening required.
B) Loca�on 41 : Start / Stop Mode (toggle)
The relay outputs can be programmed to trigger ON (start) and OFF (stop) with a user code.
C) Loca�on 42 : Start / Stop Mode (toggle) with 2-digit Accelerated Code
The relay outputs can be programmed to trigger ON with only the first 2 digits of a user code and
OFF with a full user code.
Example:
a) User Code 8 3 2 1 is a full code, then the first 2 digit 8 3 is the accelerated code.
b) User Code 5 4 3 2 1 is a full code, then the first 2 digit 5 4 is the accelerated code.
D) Loca�on 43 : Start / Stop Mode (toggle) with 3-digit Accelerated Code
The relay outputs can be programmed to trigger ON with only the first 3 digits of a user code and
OFF with a full user code.
Example:
a) User Code 5 4 3 2 1 is a full code, then the first 3 digit 5 4 3 is the accelerated code.
b) User Code 9 2 7 0 5 3 is a full code, then the first 3 digit 9 2 7 is the accelerated code.
Configura�on of Output Modes for Output 1 (Loca�ons 40–43) Programming Examples:
1. Set keypad to programming mode with master code and key. Taking the previous programmed
master code 3 2 8 9 as example here:
2. Set Output 1 in momentary mode of 5 seconds:
3. Set Output 1 in Start / Stop Mode:
4. Set Output 1 in Start / Stop Mode with 2-digit Accelerated Start Code:
5. Exit programming mode by pressing the
16 17
Operaon :
1. Operate Output 1 in momentary mode of 5 seconds using user code 8 3 2 1 that was programmed
previously:
----------- Output 1 operates for 5 seconds
2. Operate Output 1 in Start / Stop mode using user code 8 3 2 1 that was programmed previously:
-------- Output 1 start / stop in toggle with the same user code
3. Operate Output 1 in Start / Stop mode with the 2 digit Accelerated code using user code 8 3 2 1
that was programmed previously:
----------------- Output 1 starts with Accelerated Code
----- Output 1 stops with Full User Code
NOTE:
●The purpose of the accelerated Code -- Start / Stop mode with accelerated code can be
considered as two user codes with one for star�ng and the other for stopping the output. Owner
can give the accelerated code to the staff to start a system (for example, an alarm system). The
staff can only start the system but can not stop it. Only the owner can stop the system with the
full user code.
●The Super User Code is always valid to Start / Stop the output.
Super User Code ------- Output 1 Ac�vates or De-ac�vates
The output 1 can be programmed to trigger with the following op�ons. for a programmed length of
�me from 1 to 999 seconds; or to trigger ON and OFF in toggle with a user code; or to trigger ON
with an accelerated start code and OFF with an full digit user code.
Loca�ons Time Length Confirm
A) 1 – 999
B)
C)
D)
NOTE:
Programming Loca�ons:
●Loca�ons 40, 41, 42 and 43 for Output 1
Programming Options for Output 1 (See “Programming Summary Chart” Secon D for more informaon) :
A) Loca�on 40 : Momentary Mode with �me length from 1 to 999 seconds (Default = 1 second)
The relay outputs can be programmed to work for a �me length from to seconds to
cope with the door opening required.
B) Loca�on 41 : Start / Stop Mode (toggle)
The relay outputs can be programmed to trigger ON (start) and OFF (stop) with a user code.
C) Loca�on 42 : Start / Stop Mode (toggle) with 2-digit Accelerated Code
The relay outputs can be programmed to trigger ON with only the first 2 digits of a user code and
OFF with a full user code.
Example:
a) User Code 8 3 2 1 is a full code, then the first 2 digit 8 3 is the accelerated code.
b) User Code 5 4 3 2 1 is a full code, then the first 2 digit 5 4 is the accelerated code.
D) Loca�on 43 : Start / Stop Mode (toggle) with 3-digit Accelerated Code
The relay outputs can be programmed to trigger ON with only the first 3 digits of a user code and
OFF with a full user code.
Example:
a) User Code 5 4 3 2 1 is a full code, then the first 3 digit 5 4 3 is the accelerated code.
b) User Code 9 2 7 0 5 3 is a full code, then the first 3 digit 9 2 7 is the accelerated code.
Configura�on of Output Modes for Output 1 (Loca�ons 40–43) Programming Examples:
1. Set keypad to programming mode with master code and key. Taking the previous programmed
master code 3 2 8 9 as example here:
2. Set Output 1 in momentary mode of 5 seconds:
3. Set Output 1 in Start / Stop Mode:
4. Set Output 1 in Start / Stop Mode with 2-digit Accelerated Start Code:
5. Exit programming mode by pressing the
16 17
Deleng Examples:
3289
a)
b)
c)
Dele�ng User Codes & Other Func�on Codes (Loca�ons 1, 45 & 47)
Loca�ons Type of Lock Confirm
Programming Codes for Type of Locks:
Important Note to Installer:
Configura�on of Output 1 for Electric Lock (Loca�on 66)
de-energized
(Default)
energized
1518
Programming Codes for Lock-Up Opons:
(Default)
Super User Code
Programming Examples:
3 2 8 9
One-Time
Time-Limit
User ID Entry of Code
NOTE:
●
●0-9
●
●
●
●
Programming Example :
3 2 8 9
2. Program a Visitor Code 1 3 7 8 at ID “0” for One-Time use:
3. Program a Visitor Code 2 3 0 8 9 at ID “1” with Time-Limit of 5 hours:
4. Program a Visitor Code 8 3 5 8 at ID “2” with Time-Limit of 10 hours:
Operaon :
14 19
Other manuals for DOLKSS1KB
1
Table of contents
Other Transmitter Solutions IP Access Controllers manuals
Popular IP Access Controllers manuals by other brands
ZKTeco
ZKTeco Green Label ProlD104 user manual
Intelligent Building Solutions
Intelligent Building Solutions CAP 2020 DR IB installation manual
Assa Abloy
Assa Abloy HID Signo Biometric Reader 25B user guide
Maco
Maco openDoor Touch user manual
Door-Gard
Door-Gard LS2 Programming manual
Control iD
Control iD iDUHF quick guide