TRANWO Technology TTA-A5805R User manual

5.8 GHz Wireless
Audio/Video Sender

1
To prevent fire or shock hazard, do not expose this product to rain and
moisture. For example: do not use near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement, or nearby a swimming pool. To
avoid electric shock, do not take apart this product, provided as an
accessory. This product should be operated only under power supply.
Do not overload wall outlets and extension outlets as this can result in
the risk of fire or electric shock.
Contents
1.Important Safety Information
1.Important Safety Information.......................................1
2.Package Content........................................................2
3.Panel Control And Function......................................... 3
4.Setup Guide...............................................................4
5.Orient Transmitter/Receiver for optimal performance.....5
FCC Statement
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Note:
This equipment has been tested and found to comply with the limits regulated
by FCC and CE. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to
radio communications. The change or modifcations not expressly approved by
the party responsible for compliance could void the user’s authority to operate
the equipment. To comply with the FCC RF exposure compliance requirements,
no change to the antenna or the device is permitted. Any change to the antenna
or the device could result in the device exceeding the RF exposure requirements
and void user’s authority to operate the device.
Industry Canada Statement
This device complies with RSS-210 of Industry Canada. Operation is subject
to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.

2.Package Contents
Check to make sure that all units shown as below are enclosed.
If something missed, please contact your dealer.
3. IR Cable LED x 1
2. 5.8GHz Receiver x 1
UHF:433.92MHz
4.
(9V/500mA) x 2
Power Adapters
1. 5.8GHz Transmitter x 1
5. Cables x 2
2
EUROPE Type
USA Type
EUROPE Type(SCART Cable)
USA Type(RCA Cable)

2.Package Contents3.Panel Control and Function
1
3
4
2
1. UHF Antenna
2. ON/OFF Switch
3. Power Indicator/IR Windows
4. IR mouse jack (transmitter only)
Channel selection button to find optimal reception (receiver only)
5. Power Adapter Jack
6. DIP switch for ID code, the transmitter and receiver
must to be configured as the same ID code.
7. A/V Jack
5
6
7
ID Code
3
Transmitter/Receiver
Note:
To eliminate static or unclear pictures caused by improper
installation, please check the power of transmitter is already on,
then turn off receiver power, press still on the channel selection
button of receiver until you have turned on receiver power again.
1 2 3
ON
1 2 3
ON
1 2 3
ON
1 2 3
ON
1 2 3
ON
1 2 3
ON
1 2 3
ON
ID 2
1 2 3
ON
1 2 3
ON
ID 1 ID 4ID 3
ID 6ID 5 ID 8ID 7

2.Package Contents4.Setup Guide
1. Connect one end of the RCA cable
(or scart cable) to the audio and video
jacks, and connect the other end to a
source device as well.
2. Connect the DC plug of the adapter
to the DC jack, and connect the power
supply to an outlet.
3. Keep the IR window oriented toward
the source AV equipment, or
alternatively use the IR Mouse to
remotely control it.
2.Package Contents
Not e:Mak e su re the ON/OFF swi tch is in the OFF pos ition bef ore co nne ct ion「 」
Transmitter
OUT
IR cable LED
Transmitter
Remote
Controller
IN
Receiver
1. Connect one end of the RCA cable
(or scart cable) to the audio and video
jacks, and connect the other end to a
TV (or monitor, speakers) on which
you like to enjoy a program.
2. Connect the DC plug of the adapter
to the DC jack, and connect the power
supply to an outlet.
3. Keep the IR window oriented toward
your remote controller.
To enjoy a life of wireless video and audio, just connect the
transmitter to whatever A/V source you like and connect the
receiver to a TV, monitor or speaker in another location.
4
To AV Equipment
Receiver
To TV
* A complete set-up procedure consists of:
1. Press “CH” button on receiver, receiver
will make transmitter switch to the same
channel.
2. Make sure the ID on transmitter and
receiver is identical (For example, as exhibit
Transmitter: Receiver: )
whenever there is problem with installation, please implement the set-up
procedure again.
1 2 3
ON
ID 1
1 2 3
ON
ID 1

Receiver
Transmitter
5.Orient Transmitter/Receiver for optimal performance
5
For optimal performance, both the audio/video and remote
control antennas should be carefully oriented as described
below. For maximum transmitting range, try to minimize
obstacles (e.g. your TV or other electronics, large furniture)
where between the transmitter and receiver.
Orients the 5.8GHz A/V Antennas
5.8GHz Antenna
5.8GHz Antenna
Transmitter Receiver
5.8GHz Antenna 5.8GHz Antenna
Fig. 1
Fig. 2
The system delivers high-quality
audio and video by using directional
antennas, which must be oriented
to get the best results.
The antennas are designed to
be able to rotate in almost any
direction.
In most situations, the convex
of the antennas on both the
transmitter and receiver should be facing one another and
perpendicular (at a right angle) to an imaginary line drawn
between the two units. Two examples are shown as Fig.1,
Fig.2. Since all homes are different, for optimal reception,
additional alignment may be necessary.
If the transmitter and receiver are less than 10 feet apart,
suggest to lie the antennas on their casings since the distance
is so short.

6
Orients the UHF Antennas
In order to obtain optimal performance of the remote control
extender, the remote control antennas should also be oriented
at a right angle to an imaginary line drawn between the
transmitter and receiver.
If your remote control extender is not working satisfactorily,
rotate the remote control antenna on either the transmitter or
receiver 90 degrees so that it is still perpendicular to the path
between the units.(See Fig.3)
IF you notice improved performance, keep this orientation.
Rotating the antenna on both units should have no effect.
Receiver
Fig. 3
Transmitter
UHF Antenna
UHF Antenna
WEEE Directive & Product Disposal
At the end of its serviceable life, this product should
not be treated as household or general waste. It
should be handed over to the applicable collection
point for the recycling of electrical and electronic
equipment, or returned to the supplier for disposal.

408-000638-00
TTA-A5805T
TTA-A5805R
This equipment is intended to be
operated in below countries.