TRASSIR TR-D8151IR2 User manual

Outdoor IR Network Camera
TR-D8151IR2
Specification
TR-D8151IR2
1/2.8" CMOS 5Мп
5MP(2592x1944)
4MP(2592x1520)
3MP(2304x1296)
5MP@15fps
4MP@20fps
3MP@25fps
1/2 ~ 1/1 000 c
Mechanical ICR
0.003Lux (F1.8)
up to 25 m
2.8 / 3.6
2.8mm: 102˚±5˚ / 72˚±5˚
3.6mm: 83˚±5˚ / 60˚±5˚
Real WDR (120dB)
3D DNR
Н.265 / H.264
up to 8Mbps
MicroSD up to 128Gb
Built-in microphone
Yes
Human Detection
Line Crossing
Intrusion Detection
No
PoE (802.3af) / 12V DC
3
DC: 3.6W
PoE: 4.8W
Metall
Ø92.8 x 92.2
380 / 480
IP66, IK10
TVS 4000V
-40°C … +60°C
Model
Image sensor
Resolution
Frame rate
Electronic Shutter Speed
Day/Night Mode
Sensitivity
IR range
Lens (mm)
Field of view (horiz./vert.)
WDR
Digital noise reduction
Video compression
Bitrate
Local storage
Audio
Corridor mode
IVS
RTC
Power supply
Class PoE
Power consumption
Case material
Dimensions (mm)
Weight Net/Gross (g)
Ingress protection
Lighting protection
Working temperature
Note: read user manual before using
Website: www.trassir.com
For any inquiry: inf[email protected]
H.265
HEVC
Technical support
www: helpdesk.trassir.com
mail: helpd[email protected]
Data ___________________________ Stamp ___________________________
Here is the confirmation form for warranty assurance

Manual setting of network parameters.
IP-camera and PC should be in one local network to connect to each
other. In this case IP address of a camera, PC or any other devices
shouldn't match each other.
IP camera has the following default settings:
- IP address: 192.168.1.188
- Subnet mask: 255.255.0.0
- Gateway: 192.168.1.1
- HTTP-port: 80
- username: admin
- password: admin
Example of network settings for PC to connect to IP camera:
- IP address: 192.168.1.10;
- Subnet mask: 255.255.0.0.
There are 3 options to set up your camera:
1. Change IP address of a camera manually.
Start your browser, connect to IP camera and enter your
username and password. Choose appropriate menu item and change
network settings of IP camera.
2. Set IP address of a camera using fast configuration utility which could
be downloaded from www.trassir.com.
3. Change IP camera settings using TRASSIR professional software.
Find detailed instruction on camera settings in user manual which could
be downloaded from our website www.trassir.com.
Introduction
Congratulations with purchasing of IP camera TR-D8151IR2.
Please read User Manual before using a camera.
Key features
• Support codec H.265
• Wide Dynamic Range (Real WDR 120dB)
• IR range up to 25 m
• Onboard video archive (Edge Storage) – local recording
on MicroSD card* up to 128GB
• Built-in microphone
• Protocol: TCP/IP, HTTP, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP,
UPnP, SMTP, NTP
• Power supply 12V DC or PoE
• Lightning protection: TVS 4000V**
___________________________
* MicroSD Card is not included into camera package
** Device must be grounded
Camera Package
1. IP camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 pc.
2. User manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 pc.
3. Mounting kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 pc.
Attention!
Power supply should meet the requirements: output voltage, current,
polarities and working temperature. Pay attention that you have lightning
conductor while using IP camera during a storm or plug off power
connector.
Pay attention to temperature requirements of IP-camera. Avoid of using
IP camera in high or low temperatures. Don't install your IP camera near
heaters.
Don't direct camera lens to the sun or bright object. It could harm your
image sensor.
Connecting
To get started with IP camera you are required to have a PC connected to
the local network with Windows installed and Internet Explorer version 8
or higher.
1. Connect IP camera to the network.
2. When the camera is connected through a switch which doesn't support
PoE, connect adapter to power jack.
Dimensions
769-27.11.20
93
92,2
∅4,5
∅93
48,4
48,4