TRASSIR TR-D8221WDIR3 User manual

2MP Eyeball IP camera
Technical support
www: helpdesk.trassir.com
mail: helpd[email protected]
Data ___________________________ Stamp ___________________________
Here is the confirmation form for warranty assurance
Note: read user manual before using
Website: www.trassir.com
For any inquiry: inf[email protected]
Specification TR-D8221WDIR3
2MP
Camera Package
IP camera
User manual
Mounting kit
1 pc
1 pc
1 pc
TR-D8221WDIR3
1/2.8" STARVIS CMOS 2MP
FullHD (1920x1080)
FullHD@25fps
Mechanical ICR
0.003Lux (F1.8) / 0Lux (IR on)
up to 30 m
1.9 / 2.8 / 3.6
3D-DNR
Real WDR (120dB)
Н.264 / H.265
8Mbps
MicroSD up to 128GB
2-way
1 / 1
PoE (802.3af) / 12V DC
3
DC: 7.6 W
PoE: 8.8 W
Ø92.8 x 89.84
380
IP66, IK10
-40°C … +60°C
Model
Image sensor
Resolution
Frame rate
Day/Night Mode
Sensitivity
IR range
Lens (mm)
Digital noise reduction
WDR
Video compression
Bitrate
Local storage
Audio
Alarm In / Out
Power supply
PoE Class
Power consumption
Dimensions (mm)
Net weight (g)
Ingress protection
Working temperature

Connecting
To get started with IP camera you are required to have a PC connected
to the local network with Windows installed and Internet Explorer
version 8 or higher.
1. Connect IP camera to the network.
2. When the camera is connected through a switch which doesn't
support PoE, connect adapter to power jack.
Dimensions
Manual setting of network parameters.
IP-camera and PC should be in one local network to connect to each
other. In this case IP address of a camera, PC or any other devices
shouldn't match each other.
IP camera has the following default settings:
- IP address: 192.168.1.188
- Subnet mask: 255.255.0.0
- Gateway: 192.168.1.1
- HTTP-port: 80
- username: admin
- password: admin
Example of network settings for PC to connect to IP camera:
- IP address: 192.168.1.10;
- Subnet mask: 255.255.0.0.
There are 3 options to set up your camera:
1. Change IP address of a camera manually.
Start your browser, connect to IP camera and enter your
username and password. Choose appropriate menu item and change
network settings of IP camera.
2. Set IP address of a camera using fast configuration utility which could
be downloaded from www.trassir.com.
3. Change IP camera settings using TRASSIR professional software.
Find detailed instruction on camera settings in user manual which could
be downloaded from our website www.trassir.com.
Notes:
Power supply should meet the requirements: output voltage, current,
polarities and working temperature. Pay attention that you have
lightning conductor while using IP camera during a storm or plug off
power connector.
Pay attention to temperature requirements of IP-camera. Avoid of using
IP camera in high or low temperatures.
Don't install your IP camera near heaters.
Don't direct camera lens to the sun or bright object. It could harm your
image sensor.
Introduction
Congratulations with purchasing of IP camera TR-D8221WDIR3.
Please read User Manual before using a camera.
Key features
• Support codec H.265
• Wide Dynamic Range (Real WDR 120dB)
• Digital Noise Reduction (3D-DNR)
• IR range up to 30 m
• Support of 2 video streams
• Two-way audio (built-in speaker and microphone)
• Alarm: 1 in / 1 out
• Onboard video archive (Edge Storage) – local recording
on MicroSD card* up to 128GB
• Power supply 12V DC or PoE
____________
* MicroSD Card is not included into camera package
853-11.1.21
93
92,2
∅4,5
∅93
48,4
48,4