Trekkrunner TR001 User manual

1
Motorized Treadmill

2
CHART OF PRODUCT
INSTRUCTION
Control Panel

3
Emergency Stop Switch
Handrail
Motor Cover
Running Belt

4
IMPORTANT SAFETY INFORMATION
Please keep this manual in a safe place for easy reference.
1. It is important to read this entire instruction before assembling and using
the equipment. Safe and effective use can only be achieved if the equipment is
assembled,maintained and used properly. It is your responsibility to ensure
that all users of the equipment are informed of all warnings and precautions.
2. Before starting any exercise program you should consult your doctor to
determine if you have any medical conditions that could put your health and
safety at risk, or prevent you from using the equipment properly. Your doctor’s
advice is essential if you are taking medicine that affects your hear rate,blood
pressure or cholesterol level.
3. Be ware of your body’s signals incorrect or excessive exercise can damage
your health. Stop exercising if you experience any of the following
symptoms:Pain, Tightness in your chest, Irregular heartbeat, Extreme
shortness of breath, light headache, dizziness, or feeling of nausea. If you do
experience any of these conditions, you should consult your doctor before
continuing with your exercise program.

5
4. Keep children and pets away from the equipment. The equipment is
designed for adult use only.
5. Use the equipment on a solid ,flat level surface with a protective cover for
your floor,or carpet. To ensure safety,the equipment should have at least 0.5
meters of free space all around it.
6. Before using the equipment,check that the nuts and bolts are securely
tightened.
7. The safety of the equipment can only be maintained if it is regularly
examined for damage and/or wear and tear.
8.Always using the equipment as indicated. If you find any defective
components while assembling or checking the equipment. Or if you hear any
unusual noise coming from the equipment during use,stop immediately. Don’t
use the equipment until the problem has been rectified.
9.While suitable clothing while using the equipment. Avoid wearing loose
clothing that may get caught in the equipment or that may restrict or prevent
movement.
10.The equipment is only for home use only. Max user weight is 120 KGS only.
Braking ability is independent of speed.
11.The equipment is not suitable for therapeutic use.
12.Please take care when lifting or moving the equipment so as not to injure

6
your back. Always use proper lifting techniques and/or seek assistance if
necessary.
Assembling Instructions
STEP 1
Open the carton, please confirm the product
accessories is complete
Accessories details:
1. Handrail decorative covers 2pcs
2. Lock screw M6X40 2pcs
3. Multi-purpose wrench 1pc
4. Lock nut M12X50 1pc
5. Spring locking pin 1pc
6. Magnet safety switch 1pc
7. 5 # Allen key 1pc
STEP 2
Connect the signal line and Insert the pillar which
have a signal line inside
into the right side base, and insert another pillar
into the left side base,
Then use M8X60 screw locking.

7
STEP 3
Screw into the spring pin
STEP 4
Use M12X50 lock screw fix the handle frame on
the base.
STEP 5
Adjust Control panel location, screw-in M6X40
lock screw
STEP 6
Put the handrails on the 2 columns, with four
M8X50 screw fixed
respectively, and put on a handrail decorative
cover on the top of screws
on each handle, then, Insert the plug of signal
lines into the socket

8
FOLDING FOR STORAGE
Please following the PIC 1,screws out the big
Screw which fixed the base and handrail,and follow
The PIC2,pull the “Spring Screws” which was fixed on
The handrail pole gently,and then release “Spring Screws”.
Belt Adjustment
PIC 1 PIC 2
Your Treadmill belt has been adjusted at the factory
but each user has a tendency to be “Right” or “Left”
footed. If the belt moves to either side,It needs to be
adjusted.
There are two adjustment bolts at the rear of the
unit(see PIC.3).Tighten by half a turn the bolt on the
side towards which the belt has shifted and
correspondingly loosen the bolt on the other side.
STEP 7
Put the security magnetic safety switch into panel
yellow area.
STEP 8
Finish the assembly.

9
Maintenance
The belt may be cleaned by a mild soap and water. Be sure to remove any excess water after cleaning.
Clean the running board under the belt periodically with a household furniture polish. After cleaning,a
small amount of silicone spray(available from motor shops) should placed on the surface of the running
board to allow the belt to slide more easily.

10
TO LUBRICATE THE DECK
ATTENTION! To reduce the risk of electrical shock, always
remove the cable from the socket immediately after use and
before cleaning.
1 - Raise the belt from the edge of one of the sides and clean
the deck and belt by wiping a dry cloth over the deck and in
internal surface of the belt. Moving the belt backwards with the
foot clean the belt along its full length. Repeat on the other
side of the belt.
2 - Place the vial between the belt and the board and hold the
vial inclined.
3 - Apply a trickle of silicone from the front to the back of the
treadmill on each side. Try to reach the center of the deck
4 - Spread the silicone by running the treadmill at 1Km/h and
step delicately on the treadmill for some minutes to enable the
silicone to spread on the belt.

11
CONTROL PANEL
Led Display
Speed Selection Area

12
Function Instruction
1. Insert the plug, put the safety key into the control panel, open the power switch, full screen display 1
second after the beep sound to enter standby.
2. In the manual standby mode initially: SPEED display 0.0； TIME display 0:00; CAL display 1; DIST
display 0.0; CAL display 0;
3. In the manual standby mode, press the MODE key, you can respectively selected the mode: normal,
preset time or preset distance. If choose count up timer, display “：” flash display; and count down,
display the static status.
A. According to the normal, the time and distance are both count up, when the time to 60 minutes, it’s
stop.
B. According to the preset time, the original time is 30:00, and the speed can be adjusted from
5:00---99:00,
and the time count down until 0, the machine stop.
C. According to the preset distance, the original distance is 1.00, you can adjust the speed from
Program
Mode
Stop
Start
Speed
-
Speed
+
The Emergency Stop Switch

13
0.50-1.00-1.50---99.5，each additional distance is 0.5km, DIST is count down until 0.
4. In the standby mode, click the program key, its P1-P12 auto program for choice, the time will show by
count down, original time is 30：00, you can adjust the time from 5:00---99:00 by speed +/- key.
5. In the standby mode, all of shortcut key are useless, if click the stop key, all will come back to manual
standby status.
6. When running all mode, it must be have 3 seconds count down (speed display), and buzzer 3seconds. In
this mode, the mode key and program key is invalid.
7. In manual operation mode, you can adjust the speed from1.0---10.0. original is 1.0,you also can choose
speed (2KM，4KM，6KM，8KM and 10KM) by speed shortcut key.
8.In automatic mode, the speed button “+/-” and the speed shortcut key are also effective, and all
auto-mode is 20 sequence shot. The details of automatic mode are as addendum.
9. In automatic mode, the machine will buzz 3 seconds earlier to prompt the user.
10. In the running status, press the “stop” key, the motor will reduce the speed until stop, and the mode
into manual standby, every motion parameter keep remain show so that the user watch conveniently.
11.When the safety key /Device left the control panel,the window show “-”,others have not show.
12. In standby mode or protected mode,no-operation continuously 10 minutes,the machine will turn off
the display to sleep.
In sleep mode,press any key(protection switch must be closed) or to detect the heartbeat,the machine
into standby immediately shows the initial.
Exercise Computer
Function Button
Mode Press to select functions preset,or hold on can be total reset for all function values.
Functions
Scan Automatically scan through each model in sequence for every 5 seconds
Time Accumulates total working time up to 30:00.

14
Speed Accumulates current speed.
Distance Accumulates current working distance up to 99.99KM
Calorie Accumulates calories consumption during exercise,Max value is 9999 Cal.
(This data is a rough guide for comparison of different exercise sessions which cannot be used in
Medical treatment)
Note:1.Without any of signal for 4 minutes ,the LCD display will shut off automatically.
2.Turn on the monitor by pressing the button.
3.Stop exercise to press model for selecting each function.
Troubleshooting
Computer not working correctly
If your computer is not working correctly,please check whether the computer sensor wire is plugged into
the computer. If you have checked the above and the computer is still not working,then please make sure
the Magnetic Switch is still working and that they are installed correctly in the computer.
Technical Specification
Production Name:Motorized Treadmill
Rated Voltage:220V
Frequency :50 Hz
Rated Power:500W