TREMAIN Link User manual

INSTALLATION MANUAL INNOVATION IN
WORKING ENVIRONMENTS

Manual de instalación - Link
Piezas:
Hardware
Screw 10/12x1" Staggered bushing
Panel
Work surface
Cantiliver
Connector post Panel finish end
Straight line connector
Corner bracket
Jumper
Support BBF
®

1. Jumper Installation
1.1 Jumpers that pass a connector post must be inserted trough the perforations prior to making the connetion to the
Panels, once the Jumper is inserted to the raceway it must connect to the power harness
Recall that the harnesses are located at the bottom of the Panels and that is where the Receptacles hould be placed
with the wiring system. The Receptacle is fixed, you will use Screws 10/12x5/8".
Image 1.1
Conector
Post
Jumper
Panel
Panel
Receptacle
®

2. Connector Post to Panel Installation
2.1 Once the Jumpers have been conducted trough post and raceway, the connector post will connect the Panel by
using the top and botton Wedge Blocks on the post.
Detail A Detail B
Image 2.1
Detail B Panel
2 Way
Connector
Panel
Inferior
Wedge
Block
Slide the inferior part of the Hanger
frame to the Inferior wedge block.
Hanger frame
Align the Hanger frame on the Panel and
post and connect using the Superior wedge
block and screw using the allen wrench.
Panel
Connector
Post
Panel
®
Superior
wedge block
Detail A

3. Panel to Panel Connection
3.1 To make a Panel to Panel Connection you will use the straight connector. You begin by sliding the inferior part of
the line Hanger frame (Detail A) and then adjusting the Superior wedge block. (Detail B)
Detail A
Image 3.1
Panel
Panel
Panel
Panel
Panel
Inferior wedge
block whit screw
Detail B
Adjust screw on the
superior wedge
Slide the Hanger frame
to the previously fixed
inferior wedge block
Hanger frame
®
Straight line connector whit
superior wedge block

4. Raceway Cover Installation
4.1 To install the Raceway cover you must use the clips on the lower part of the panel Raceway. As show
on Image 4.1
Image 4.1.
Clip
RacewayCover
Panel
®
RacewayCover

5. Work Surface Installation
5.1 To install Work surfaces you will need to place Cantilevers and Brackets at 27 3/8" high to the upper part
of the hardware, then fix the surfaces. As shown on Image 5.1. After installing the Worksurfaces, you must
install the Union Flat Brackets, between the Worksurfaces.
To fix the Surface to the Cantilever use a)Staggered bushing, b)Central Bushing, c) Leveling set screw.
Image 5.1
a
b
Screw
10/12x1"
Screw
10/12x1"
Screw
10/12x1"
Left
Cantilever
Corner
Bracket
Cantilever
NOTE:
Number and location of
brackets and Cantilevers
will vary according to
station layout.
27
Corner
Bracket
®
3/8"
Right
Cantilever
Corner
Bracket

6. Support Pedestal Installation
6.2 After removing the drawers, you must
place the structure of the drawer
underneath the Work Surface, and use
10/12x1" screws to fix the storange unit to
the Work surface. As show on Image 6.2
Image 6.2.
Screws
10/12x1"
Work Surface
(Detail 2)
Plastic Levers
Derecho
(Detail 3)
Izquierdo
1
Detail 3
Image 6.1.
®
6.1 To install Support Pedestals to a Work Surface you must first remove the drawers by following these
steps:
To begin you must remove the top drawer () and once you can see the Plastic Levers you must lower the lever on the
right rail (Detail 2) and move the lever from the left rail up (Detail 3) once you´ve done this the drawer can be
removed from rails (repeat the same process for the next drawer)

6. Support Pedestal Installation
(Detail 4) (Detail 5)
6.3 After installing the stronge pedestal structure, the drawes must be placed once again on their corresponding
rails, by taking the drawer slide rail and inserting to the drawer rail. Make sure that the bearings on the rails are
at the front. (Detail 5)
Image 6.3.
Image 6.4.
The drawers must be aligned with the front of the Work Surface (Image 6.4)
®

7. Installing Panel Finished Ends
7.1 To install the Finished End to a Panel you must slide the Angled Bracket on the Finished End to the Hanger
frame on the Panel (Detail A), then you need to align the top of the Finished End by adjusting the Wedge Block with
the screw until fixed. (Detail B)
Detail B
Detail A
Image 7.1
Panel
Finished End
Superior
Wedge
Block
Superior
Wedge Block
®
Angled Bracket
Finished
End

Wall
Wall
Wall
Once joined, place the panel and fix it using superior and inferior wedge blocks.
Wall start installation

Additional Items

Screw
10-12X1
Join the wall start with the hanger frame using 10-12 x 1" screws.
Wall start installation

LINK SLIDE DOOR

LINK SLIDE DOOR

LINK SLIDE DOOR