Trend Sports BallField BF199 User manual

Read This Before Operating
IMPORTANT
DO NOT RETURN THE BALLFIELD TO THE RETAIL STORE WHERE PURCHASED.
CALL TOLL FREE: [phone].
CUSTOMER SERVICE
TREND SPORTS is dedicated to your customer satisfaction. If you experience any trouble with the BallField contact us at:
[phone] or go to our website at www.TrendSports.com.
BALLFIELD RECOMMENDATIONS
Trend Sports recommends using Slider Lite-Balls for younger players when using the pitching and fielding rebounder on the BallField.
WARNING: THIS PRODUCT IS TO BE USED BY ADULTS ONLY. MAKE SURE THE AREA IS CLEAR BEFORE SWINGING A BAT. ONLY ADULTS SHOULD
MAKE REBOUNDER ADJUSTMENTS. KEEP HAND AND FINGERS CLEAR OF FOLDING JOINTS TO AVOID INJURY. MAKE SURE TETHERED BALLS ARE
SECURELY FASTENED BEFORE HITTING.
WARNING!
Make sure the area is clear before
swinging a bat. Serious injury could
occur.Useunderadultsupervisiononly.
• Please be sure to read all of the instructions before using the BallField .
• Parents: Your child should be made aware of the potential dangers when using the BallField Pitching,
Hitting, and Fielding system.
• The BallField is not a toy and an adult should supervise children.
• It is very important that the batter make sure the area is clear before swinging a bat.
• DO NOT use any type of ball other than the BallField balls provided, other balls could break loose
and cause injury.
• When adjusting or folding the BallField always use two people to avoid damage or injury.
95 West 650 South • St. George, Utah 84770 • PH: 800-492-9334 • PH: 435-656-1756 • Fax: [phone] • www.TrendSports.com

K
HG J IFA B CD E
O
L M N Q R
P
(Qty - 15)
Short Bungees
S
Netting
(Qty - 4)
(Qty - 2)(Qty - 2) (Qty - 2)(Qty - 2)(Qty - 2)
(Qty - 2) (Qty - 2) (Qty - 2)(Qty - 6)
Nuts, Bolts & Washers
Tools
Softball
Baseball
Adjustable
Rope
T
(Qty - 2)
U
(Qty - 2)
V
(Qty - 12)
VV
(Qty - 2)
W
(Qty - 2) X
(Qty - 12)
Y
(Qty - 34)
YY
(Qty - 4)
XX
(Qty - 2)
Z
(Qty - 4)
ZZ
(Qty - 2)
UU
(Qty - 6)
Model# BF199
BALLFIELD PARTS LIST

STEP 1:
Locate parts A, B, C, D, both Gparts, and
two Hparts. Lay them flat on the ground and
assemble as illustrated. Connect the parts by
sliding the tapered ends into the larger ends
and lock in place with the push-pins.
BALLFIELD FRAME ASSEMBLY INSTRUCTIONS
B
A
G
F
F
H
H
E
G
H
H
DC
I I
HH
J K

B
A
G
F
F
H
H
E
G
H
H
DC
I I
HH
J K
STEP 3:
Continue to assemble the "base" of the BallField
by connecting parts Hand part Einto both F
parts as shown to the right.
BALLFIELD FRAME ASSEMBLY INSTRUCTIONS (Continued)
V-FRAME ASSEMBLY
BOTTOM VIEW
V
BRACE ASSEMBLY
SIDE VIEW
A
F
P
V
YY
X
Y
Y
Z
A
X
YY
V
H
F
STEP 2:
Locate parts Fand P.
Following illustration "V-Frame Assembly
Bottom View" to the right, insert part Finto
the pivot slot on part A, align the holes and
fasten together with the required nut, bolt,
and washers.
Attach part P(brace) to part Fand part Aas
shown in the "Brace Assembly Side View"
illustration.
Repeat Step 2 for the opposite side attaching
the second part Fto part B.

B
A
G
F
F
H
H
E
G
H
H
DC
I I
HH
J K
STEP 5:
Finish building the "top frame" of the BallField by
connecting parts H, J, and K into both Iparts as
shown to the right.
(Note: the BallField frame is still face down as
we continue to the next steps.)
BALLFIELD FRAME ASSEMBLY INSTRUCTIONS (Continued)
TOP VIEW
C G
I
SIDE VIEW
C
I
P
X
YY
V
Z
Y
V
Y
V
Y
Y
X
STEP 4:
Following illustration "Top View" to the right,
insert part Iinto the pivot slot on part C,
align the holes and fasten together with the
required nut, bolt, and washers.
Attach part P(brace) to part Iand part Cas
shown in the "Side View" illustration.
Repeat Step 4 for the opposite side attaching
the second part Ito part D.
(Note: part Ishould tilt as shown.)

STEP 6:
With the BallField frame still face down,
assemble the "rebounder" frame.
Locate parts L, M, N, and O. Position the parts
inside the BallField frame as shown to the right.
(Note: Make sure that parts Oare on the same
side as parts Cand D. While parts Nare on the
same side as parts Band A.)
O
N N
L
L
M
M
O
B
A
G
G
H
H
DC
STEP 7
Next take part Oof the rebounder frame and
align with the holes in part Cof the BallField
frame. Using the longer bolt (part T) and the
two black spacers (part UU) between the two
frames, fasten the rebounder frame to the
BallField frame. Repeat this step for the oppo-
site side using part D.
SIDE VIEW
C
O
I
P
X
UU
Y
Y
T
BALLFIELD REBOUNDER ASSEMBLY INSTRUCTIONS

STEP 8:
Now take the entire BallField and
Rebounder frames and stand it upright,
as shown to the right.
Locate part Q, and align the "bolt hole"
on the end with the hole in part Nof
the Rebounder frame, as shown in the
illustration.
Using the shorter bolt Wfasten the
"adjustable bracket" part Qto part Nof
the rebounder frame.
(Note: Make sure that washer XX goes
between part Qand part N.)
SIDE VIEW
N
Q
X
Y
Y
W
XX
ZZ YY
U
Y
VV
A
F
P
STEP 9
Next align part Qwith the hole on part
Aof the BallField frame. Insert bolt U
through the outside of the BallField frame,
slide washer Y, then thread nut VV, fol-
lowed by washer YY. Slide the "adjustable
slots" of part Qonto the bolt next, fol-
lowed by washer YY and finally the wing
nut ZZ on the inside of the frame.
Repeat steps 8 and 9 for the opposite side
of the frame using part B.
(Note: Make sure that parts Nare on the
bottom end with parts Band A.)
BALLFIELD REBOUNDER ASSEMBLY INSTRUCTIONS (Continued)

STEP 10:
With the BallField upright, begin by hanging the
corners T-1 & T-2 of the net from the two top cor-
ners of the "ball side" of the frame using supplied
bungees part R.
Wrap the bungee through the top most net square
and around the frame. Continue wrapping bungees
along the "ball side" of the frame using a total of 5.
Follow the same process for the right and left side of
the netting using 5 bungees (part R) on each side.
T-1
T-2
BALLFIELD NET ASSEMBLY INSTRUCTIONS
T-1 T-2

STEP 11:
Start attaching the "red target area" of the netting
to the rebounder frame.
Begin in each of the corners by wrapping the
attached bungees around the frame twice.
BALLFIELD REBOUNDER NET ASSEMBLY INSTRUCTIONS
After attaching the four corners, attach the middle
bungee on each side. (Make sure to wrap each bungee
twice as shown above. This tension gives the net the
rebounding ability.) Finish attaching the remaining
bungees to the rebounder frame.
REBOUNDER ANGLE ADJUSTMENT:
You can adjust the angle of the rebounder for grounders, fly balls,
or line-drives by loosening the wing nuts on both sides of the
"adjustment bracket" and choosing the desired slot.
(Make sure to tighten the wing nut after making the adjustments.)

STEP 12:
Fasten the ball and cord to part Jand Kof the frame
with the attached "Eye-Bolt" as shown here.
Adjust the ball height by moving the attached hook
to the desired hole in the frame.
BALLFIELD BALL ATTACHMENT INSTRUCTIONS
BALLFIELD BALL CHANGE INSTRUCTIONS
CHANGE BASEBALL TO SOFTBALL:
A- Push ball rope through the loop in the adjustable
hanging cord.
B- Pass the ball through the loop of rope attached
to the ball.
C- Pull the ball down until the knot tightens where
the two cords join.
ABC

WARNING:
WHEN FOLDING THE BALLFIELD FRAME FOR STORAGE BE CAREFUL NOT TO ALLOW THE TOP OR BOTTOM
FRAME TO FALL AFTER THE BOLTS HAVE BEEN REMOVED. SERIOUS INJURY MAY OCCURE.
KEEP FINGERS AND HANDS CLEAR OF JOINTS AS THE FRAME FOLDS!
BALLFIELD FRAME FOLDING INSTRUCTIONS
LAY FRAME ON REBOUNDER SIDE:
When folding the BallField for storage place the
frame on the ground with the rebounder face down.
FOLD FRAME:
Remove each of the wing nut bolts as indicated.
Fold the top and bottom into the center and store.