TREND CG608 User manual

CG608 User Guide
1
Welcome
Thank you for your selecting this mobile phone.
Connect to the world with CG608 CDMA mobile phone. Sophisticated features give you
every practical advantage in today’s world of fast paced communication.
Please read this manual detailed before use.

CG608 User Guide
2
FCC Interference Statement
The device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operations.
This device has been tested and found to comply with the limits for a Class B digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This device
generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this device does cause harmful interference to radio/television reception, which can be
determined by turning the device off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and the receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
SAR Information
• This device complies with Part 24 of the FCC Rules.
• This device meets government requirements for exposure to radio waves. This device is
a radio transmitter and receiver. It is designed and manufactured not to exceed limits for
exposure to radio frequency (RF) energy. These limits are part of comprehensive
guidelines and establish permitted levels of RF energy for the population. The guidelines
were developed and confirmed by independent scientific organizations through periodic
and thorough evaluation of scientific studies. The limits include a substantial safety margin
designed to assure the safety of all persons, regardless of age and health. The exposure
standard for device employs a unit of measurement known as the Specific Absorption
Rate, or SAR. Under the guidelines for your device, the SAR limit is 1.6 W/kg .The highest
SAR value for this device when tested for use at the ear is 0.222 W/kg and when worn on
the body is 0.205 W/kg.

CG608 User Guide
3
Contents
Welcome........................................................................................................................... 1
1. Essential information..................................................................................................... 6
1.1 Safety guidelines.................................................................................................. 6
1.1.1 Traffic regulations....................................................................................... 6
1.1.2 Switch off your phone at filling stations and sensitive areas ...................... 6
1.1.3 Switch off your phone on aircraft................................................................ 6
1.1.4 Switch off your phone in the hospital ......................................................... 6
1.1.5 Pacemakers and medical implants ............................................................ 7
1.1.6 Other medical devices ............................................................................... 7
1.1.7 Follow mandatory signs............................................................................. 7
1.1.8 Emergency calls......................................................................................... 7
1.1.9 Electronic devices......................................................................................8
1.2 Care and maintenance information...................................................................... 8
2. Handset guide............................................................................................................... 9
2.1 Keypad................................................................................................................. 9
2.1.1 Power /End key.......................................................................................... 9
2.1.2 Send key.................................................................................................... 9
2.1.3 Function keys............................................................................................. 9
2.1.4 Four ways navigation key ........................................................................ 10
2.1.6 # (hash) key............................................................................................. 10
2.1.7 * (star) key................................................................................................ 10
2.1.8 Numeric keys........................................................................................... 10
2.1.9 Volume key (up and down key in navigation key).................................... 10
2.2 Idle mode screen ................................................................................................11
2.2.1 Screen indicators and icons......................................................................11
2.2.2 Idle mode screen events..........................................................................12
2.3 Installing Battery and RUIM card ....................................................................... 12
2.3.1 Installing the battery................................................................................. 12
2.3.2 Removing the battery............................................................................... 12
2.3.3 Installing the RUIM card........................................................................... 13
2.3.4 Removing the RUIM card......................................................................... 13
2.4 Charging the Battery.......................................................................................... 13
2.5 Headset.............................................................................................................. 14
2.6 Switching a Phone On/Off.................................................................................. 14
2.6.1 Entering your RUIM card PIN Code......................................................... 14
2.6.2 Entering your Phone Lock Code.............................................................. 15
2.7 Dialing a number................................................................................................ 15
2.7.1 Using the digits keys................................................................................ 15
2.7.2 Dialing a number using the Recent Call List ............................................ 16
2.7.3 Dialing a number using the Contacts List................................................. 16
2.7.4 Dialing a number using Speed Dial..........................................................16
2.7.5 Making an International call..................................................................... 16
2.7.6 Ending a call ............................................................................................ 16

CG608 User Guide
4
2.8Receiving a call................................................................................................... 16
2.9 During a phone call............................................................................................17
2.9.1 Mute......................................................................................................... 17
2.9.2 Names ..................................................................................................... 17
2.9.3 Menu........................................................................................................ 17
3. Menu overview............................................................................................................ 17
3.1.1 Write message......................................................................................... 17
3.1.2 Inbox........................................................................................................ 18
3.1.3 Outbox ..................................................................................................... 19
3.1.4 Templates................................................................................................. 19
3.1.5 Erase Msg................................................................................................ 20
3.1.6 Voice mail ................................................................................................ 20
3.1.7 Settings.................................................................................................... 20
3.1.8 Msg settings............................................................................................. 21
3.1.9 Memory status ......................................................................................... 22
3.2 Call History......................................................................................................... 22
3.2.1 Missed ..................................................................................................... 22
3.2.2 Received.................................................................................................. 22
3.2.3 Dialed....................................................................................................... 22
3.2.4 Erase history............................................................................................ 23
3.2.5 Call duration............................................................................................. 23
3.3 Profiles............................................................................................................... 23
3.3.1 Vibrate only.............................................................................................. 24
3.3.2 Silent........................................................................................................ 24
3.3.3 General.................................................................................................... 24
3.3.4 Outdoor.................................................................................................... 24
3.3.5 Headset ................................................................................................... 24
3.4 Settings.............................................................................................................. 25
3.4.1 Display..................................................................................................... 26
3.4.2 Call........................................................................................................... 26
3.4.3 Phone ...................................................................................................... 27
3.4.4 Security.................................................................................................... 28
3.5 Organizer........................................................................................................... 29
3.5.1 Scheduler................................................................................................. 29
3.5.2 Alarm clock .............................................................................................. 29
3.5.3 Calculator................................................................................................. 29
3.5.4 Tip calculator............................................................................................ 30
3.5.5 World clock .............................................................................................. 30
3.5.6 Stop watch ............................................................................................... 30
3.5.7 Game....................................................................................................... 30
3.6 Mobile web.........................................................................................................31
3.6.1 WAP......................................................................................................... 31
3.7 Names................................................................................................................ 31
3.7.1 List ........................................................................................................... 31

CG608 User Guide
5
3.7.2 Add name................................................................................................. 33
3.7.3 Find.......................................................................................................... 33
3.7.4 Multicopy.................................................................................................. 33
3.7.5 Groups..................................................................................................... 34
3.7.6 Erase all................................................................................................... 34
3.7.7 Speed dial................................................................................................ 34
3.7.8 Memory status ......................................................................................... 35
3.7.9 User’s vCard............................................................................................ 35
4. Input method............................................................................................................... 35
4.1 Number (123)..................................................................................................... 35
4.2 Character (Abc/abc/ABC)................................................................................... 35
4.3 Entering symbols ............................................................................................... 36
5. USB windows device driver installation guide............................................................. 36
5.1 Introduction ........................................................................................................ 36
5.2 Components....................................................................................................... 37
5.3 Installation.......................................................................................................... 37
6. Frequently asked questions (FAQ).............................................................................. 43
7. Trouble shooting.......................................................................................................... 44

CG608 User Guide
6
1. Essential information
Given here is essential information that will help you in the optimum operation of your
mobile phone. By adhering to these guidelines you will be protecting yourself from
unnecessary personal or financial damages or infringements of the law. Kindly read the
User Guide in its entirety for complete information.
1.1 Safety guidelines
1.1.1 Traffic regulations
Traffic and road safety regulations prohibit your usage of the phone while driving. If,
however the need arises, please do make use of the hands-free settings or move your car
to the side of the road out of the flow of traffic. In case you use an air bag equipped vehicle,
please do not place your phone in the air bag deployment area, it could result in serious
personal injury and possible property damage.
1.1.2 Switch off your phone at filling stations and sensitive areas
Areas with a potentially explosive atmosphere are often, but not always, clearly marked.
These include fuelling areas such as fuel filling stations, below decks on boats, fuel or
chemical transfer or storage facilities, vehicles using liquefied petroleum gas (such as
propane or butane), areas where the air contains chemicals or particles, such as grain,
dust, or metal powders; or any other area where you would normally be advised to turn off
your vehicle's engine. Electric or static sparks in such areas could cause an explosion or
fire resulting in serious injury or even fatalities.
1.1.3 Switch off your phone on aircraft
Follow airline advisories on phone usage. Radio Frequency emissions from wireless
devices such as your phone can cause electronic interference or disturbance in the
delicate communication and control electronic equipment of the aircraft.
1.1.4 Switch off your phone in the hospital
Switch off your phone in healthcare facilities when any regulations posted in these areas
instruct you to do so. Hospitals or healthcare facilities may be using equipment that could

CG608 User Guide
7
be sensitive to external RF energy.
1.1.5 Pacemakers and medical implants
The Health Industry Manufacturers Association (USA) recommends that a minimum
separation of six inches (15 centimeters) be maintained between a handheld wireless
product and medical implants (electronic) such as a Pacemaker to avoid potential
interference with the implant. These recommendations are consistent with the
international recommendations governing the usage of wireless technology.
Advisory for persons with Pacemakers:
zAlways keep the phone more than six inches from your pacemaker when the phone is
turned on.
zDo not carry the phone in a breast pocket.
zPreferably use the ear opposite the pacemaker to minimize the potential for
interference.
If you have any reason to suspect interference is occurring, switch off your phone
immediately.
1.1.6 Other medical devices
If you use any other personal medical device, do consult the manufacturer of the medical
device to determine if it is adequately shielded from external RF energy. Your physician
may be able to assist you in obtaining this information.
1.1.7 Follow mandatory signs
Always follow phone etiquette in public places. Switch off your phone where the use of
mobile phones is explicitly forbidden, as it may be a safety risk or might infringe on the
law.
1.1.8 Emergency calls
Emergency calls can be dialed at anytime - even if the handset is PIN locked or has no
RUIM card.
• Emergency call procedure:
Type in the local emergency number and press the send key.
Emergency call numbers are: 112/911

CG608 User Guide
8
1.1.9 Electronic devices
Most modern electronic equipments are shielded from Radio Frequency (RF) energy
emissions. However, certain electronic equipment may not be shielded against the RF
signals emitted by your phone and care must be taken in usage of your phone next to
sensitive electronic equipment.
1.2 Care and maintenance information
Your phone is an electronic device that should be treated with due care during usage. The
guidelines given here will help you in caring for your phone and keep it under warranty
coverage.
Protect your phone from dust, temperature, humidity and other extreme
environmental conditions as it will affect the performance or damage the instrument. Do
not use or store your phone in a low temperature environment as moisture will condense
in the phone and damage the circuit board.
Avoid striking, shaking or causing physical shock to the phone.
Protect your phone from rain, spilled beverages or other forms of moisture that can
damage the electronics of your phone.
Use the batteries and fittings manufactured by Hangzhou Newsky Technology Co.,
Ltd. only. The use of other fittings may cause dangerous accidents and void all warranties.
Do not disassemble the phone or its accessories. If service or repair is required,
contact a Newsky authorized service centre.
Do not inadvertently cause short-circuit by placing metal or conductive material
across or on battery terminals.
zKeep your phone and accessories out of the reach of young children.
zDo not use chemical solvents or detergents to clean your phone.

CG608 User Guide
9
2. Handset guide
Appearance
2.1 Keypad
2.1.1 Power /End key
Pressing and holding the key can switch on/off the mobile phone. Pressing the key can
end a call during a phone call or reject an incoming call. Pressing the key in the menu can
also return to the idle mode.
2.1.2 Send key
You can dial or answer a call with the key. In idle mode, pressing the key can lead you to
the recent calls list.
2.1.3 Function keys
The Left/Right keys are used to carry out the corresponding operation of last line on

CG608 User Guide
10
display screen, in accordance with the procedure are adopted to acquire different
functions.
In idle mode, press left soft key to enter the Menu function, press right soft key to enter the
Names function.
2.1.4 Four ways navigation key
The navigation keys can control the cursor directions. Left/right key can move the cursor
in text editing mode left /right. Up/down key can scroll the cursor in a list up/down.
In idle mode:
Up key: Press this key to enter the Messages directly.
Left key: Press the key to enter the active the Contacts list.
Right key: Press the key to enter the Profiles menu directly.
Down key: Press the key to enter the active the Call history.
2.1.6 # (hash) key
In idle mode, you can press and hold key to switch the Vibrate Mode on or off.
In text editing mode, press key to change input methods.
2.1.7 * (star) key
In idle mode, press and hold key to lock the keypad. By pressing any key, the
screen displays message ‘Key guard active, press 123 to unlock keypad’. Then press
123 to unlock (no longer than 15 seconds between two clicks).
In text editing mode, press key to switch to symbol mode.
2.1.8 Numeric keys
Pressing these keys can enter the digits 0 to 9 (in idle mode or in number-inputting mode)
or some associated characters (text editing mode) and perform associated functions (in a
list).
2.1.9 Volume key (up and down key in navigation key)
You can adjust the speaker volume using side keys directly during a call.

CG608 User Guide
11
2.2 Idle mode screen
2.2.1 Screen indicators and icons
Depending on your wireless service provider, some or all of the following indicators and
icons may be displayed on your phone’s screen.
When the phone is powered on, the following icons may be displayed:
2.2.1.1Battery level indicator
The Battery Level Indicator shows the representative charge held by the phone’s battery.
Bar segments within the Battery Level Indicator show the level of charge held. All bars
visible indicate a full charge. If only one or two bars are visible, it means the battery is low.
2.2.1.2 New message
The icon is displayed on your screen when a new message arrives. The new message
icon disappears when you read all the unread messages.
2.2.1.3 Full message
When the SMS storage is full, the icon appears and the phone display shows ‘SMS
capacity full. Please erase message to proceed’
One or more messages must be erased before the new message can be stored.
2.2.1.4 Alarm clock
The icon appears when the daily alarm or the alarm for the specified date and time is set.
2.2.1.5 Scheduler
The icon appears when the scheduler is set.
2.2.1.6 Network
It shows the signal strength.
2.2.1.7 Profiles
You can easily alter the phone tone (e.g. the ringer volume, keypad tones, etc.) according
to your environment.
When a profile is available, the icon corresponding to the profile name is displayed in idle
mode:
Vibrate only: For use when vibrate only is needed.
Silent: For use when silence is needed.
General: Is the default setup.

CG608 User Guide
12
Outdoor: For use in the outdoor.
Headset: For use when insert the headset.
2.2.2 Idle mode screen events
2.2.2.1 Idle mode
The mobile phone enters idle mode without any operations after the phone is switched on.
You can view the current time and date in idle mode. You can dial a number by pressing
key if you input a telephone number.
2.2.2.2 Calling
You can make a phone call after the number is dialed.
2.2.2.3 Missed calls
The missed calls and their numbers will be shown on the screen in idle mode. Press right
soft key to view the list.
2.2.2.4 New messages
When the new message is received:
1. Your phone makes alert tones (ringer, vibration or silence).
2. If the keypad is unlocked, your phone display will show ‘You have 1 new message!’
Press left soft key to view the message’s contents and then press left soft key again
to operate options. Press right soft key or power/end key to return to the idle mode,
the new message-prompting icon is displayed on the screen.
3. If the keypad is locked, your phone display will also show ‘You have 1 new
message!’ But you can’t view the contents.
Note: If the message is urgent /emergency, your phone displays ‘You have 1 new message
(Urgent/Emergency)! ’.
2.3 Installing Battery and RUIM card
2.3.1 Installing the battery
zAim the protruding part at the bottom of the battery at the groove of the phone.
zPush the top part of the battery to the phone and press down the lock until it is locked.
2.3.2 Removing the battery
Switch off the phone, push up the lock at the top of the battery to uplift the top of the

CG608 User Guide
13
battery and separate it with the main board.
2.3.3 Installing the RUIM card
Purchase a RUIM card from network operator. Your phone number and registration
information are stored in your RUIM card. Your RUIM card can be used in any a CDMA
phone. Your number and information will not change.
zMake sure to switch off your phone before taking out the battery.
zMake the metal face of the RUIM card down and put it conferring the level of the card.
Then install the battery.
2.3.4 Removing the RUIM card
zRemove the battery after switching off your phone.
zRemove the RUIM card.
zInstall the battery.
2.4 Charging the Battery
The Z-222 can be charged either when it is switched on or off.
1. Plug the charger transformer into a standard outlet.
2. Insert the charger output plug into charging connector of the USB port of the phone.
3. The rolling of the electric quantity bar indicates that the phone begins to charge.
4. When the battery level full, charge roll will stop.
5. After charging is complete, switch off the electric supply. Pinch together the spring
clamps on both sides of the charger’s jack and pull out the charger’s jack.
Note:
zWhen the battery level is low and only a few minutes of talk time remain, a beep is heard, the battery
icon flashes and the phone display ‘Battery Low, please recharge soon!’ When battery is drained
completely, the phone displays ‘Battery too low, Power off soon!’
zWhen the battery is completely discharged, your phone will turn off.
zThe battery can be charged whenever you want. However, using your phone while charging can
increase the charging time.
zIt is recommended that you charge the battery for three hours (full charging period) before you use
it.

CG608 User Guide
14
zDo not pull out the plug of the charger during charging to avoid electrical damage to the phone and
the charger.
2.5 Headset
If you connect the headset with the phone, it will be to activate headset mode or to match
the volume of headset with that of mobile phone.
Increase or decrease the volume through up and down up/down key during call.
If you plug out the headset from the phone, the phone will return to normal mode
automatically.
2.6 Switching a Phone On/Off
Press and hold down the red key to switch your phone on or off.
If you switch the phone on and there is no RUIM card inserted, the phone displays ‘Please
insert RUIM ’. Press right soft key to only dial emergency call.
After inserted, the phone will check whether the RUIM card is valid.
Then the screen displays the following messages:
zEnter PIN --- Request to input the RUIM card PIN code (if required).
zEnter Lock code --- In idle mode, press right soft key to request to enter the phone
lock code (if required).
Note:
If the RUIM card is invalid, the phone displays ‘RUIM card rejected’, please contact your network service
provider.
In the instances above mentioned, press left soft key to only dial emergency call.
2.6.1 Entering your RUIM card PIN Code
You can set protection code (PIN CODE) in order to prevent random using of your phone
by others. Each time you restart your phone, the phone will prompt you to enter PIN code
(The default PIN is 1234). In this condition, press left soft key to dial emergency call.
zInput PIN code (supplied by network service provider. For security, an * will be
displayed on the screen to in place of the number you enter.)
zIf you make a wrong enter, you can press right soft key to re-enter the code.

CG608 User Guide
15
zPress left soft key, and after a short time, your mobile phone will confirm its
correctness and begin to register on the network. Once the network name is shown
on the screen, you can call or access any of the functions of your phone. If no
network name is shown on the screen, you may need to register again.
Note:
If you have entered the PIN code incorrectly continuously for max retries limits, the RUIM card will be
automatically locked. In this condition, the phone will prompt for PUK (PIN Unlocking key). You can get
the PUK from your mobile phone service provider.
2.6.2 Entering your Phone Lock Code
The phone lock code is used to protect your phone from unauthorized use.
It can be set to automatically lock your phone each time it is switched on or when in idle
mode. In this condition, you can only dial emergency call.
You must press right soft key to enter correct phone lock code, and then access the
phone menu (The default is 0000).
The PIN code and Phone lock code can be changed.
2.7 Dialing a number
To dial a number, your phone must be switched on and unlocked.
You can use the function only after the network-prompting icon is shown on the screen.
2.7.1 Using the digits keys
Enter district code and telephone number or mobile phone number, press key to
dial.
zPress right soft key to delete a typed number. Press and hold right soft key to
delete all numbers.
zTo indicate that you are dialing a number, the word Calling displays the screen.
zIf the call is not answered and you want to end the call, press key.
zIf the call is answered, the display will change to Call Connected，press key to
end the call.

CG608 User Guide
16
2.7.2 Dialing a number using the Recent Call List
The mobile phone can store no more than 30 latest call logs (incomings, outgoings and
missed calls).
1. In idle mode, press key or press up navigation key to enter the recent calls list.
2. Scroll the list by pressing the up/down navigation key and select an entry.
3. Press key to dial.
2.7.3 Dialing a number using the Contacts List
1. In idle mode, press left navigation key or press right soft key to enter the contacts list.
2. Scroll the list by pressing the up/down navigation key and select an entry.
3. Press left soft key to dial.
2.7.4 Dialing a number using Speed Dial
Speed dial is a fast way to call one of your special numbers. See ‘Speed dial list’ menu.
2.7.5 Making an International call
zPress and hold key until "+" appears on screen.
zEnter the country code, area code (without prefix zero) and phone number.
zPress key to dial.
2.7.6 Ending a call
You can end a call at any time by holding down the key till the call has
been terminated.
2.8Receiving a call
When you receive a call, the phone will alert and the word ‘Incoming call’ displays on the
screen. If your phone has Caller Line Identification and the calling party is in Contacts list,

CG608 User Guide
17
the caller’s number and name also appears.
Press key or any key (need setting) to answer the call. Please refer to ‘Any key
answer’ menu.
Press key to reject the incoming call.
2.9 During a phone call
After pressing left soft key, user can view following contents given below:
2.9.1 Mute
Temporarily turns the microphone off during a phone call. Reselect this option to resume
your conversation.
2.9.2 Names
This function allows you to access the Names menu.
2.9.3 Menu
By using this feature, you can directly enter the menu list.
3. Menu overview
Your RUIM card can be used in the handset for accessing the menu options detailed
below. If the RUIM card is not inserted, you can still make SOS (emergency) calls.
3.1.1 Write message
Allow user to edit text message. When composing text messages, check the number of
characters allowed in the top right corner of the message. Per message can contain up to
160 characters. If you cross the limit, the phone prompts with a ‘Sorry, No more space!’
pop-up message.
Press numeric key to input corresponding characters.
Note: Press and hold right soft key to delete entire message and start a new one.
Press left soft key to access the following Message options:
3.1.1.1 Send
After writing the message, press Send option to input the recipient’s number or retrieve a

CG608 User Guide
18
number from the Names list. Then select Send option to send the message.
3.1.1.2 Insert templates
When composing an SMS message, you can use the Insert templates option, scroll
through a list of prewritten messages and select the one you want to insert into your new
text message.
3.1.1.3 Send to group
One message can be sent to a group included one or more people (no more than 10).
You can use the Send to group option, scroll through a list of groups and select the one
you want to send.
3.1.1.4 Insert number
When composing an SMS message, you can use the Insert number option, scroll through
names list and select the number you want to insert into your new text message.
3.1.2 Inbox
When you receive a new message, the new message-prompting icon will be displayed on
the LCD right corner.
zEnter the inbox menu, the current message position and the total number of received
messages will be displayed at the first row of the screen. If there are no messages,
‘No message’ will be displayed. If there are messages, the new messages will be
displayed first, followed by the old. Once you have read a new message, it will
become old.
zYou can press up/down navigation key to highlight the message you wish to view.
The message icon is displayed. See ‘Table [1]’.
The sender’s phone number is displayed. When the sender’s phone number is stored in
the contacts list, the sender’s name is displayed instead of the phone number.
zPress left soft key to display the whole message details, the message contents, and
the phone number who sent it and when it was received. Here pressing key
allows you to call the sender.
Table [1]: The message icons in Inbox
Icon Description
This is a new normal message. It can be stored into RUIM Card Memory.
This is an old normal message. It can be stored into RUIM Card Memory.

CG608 User Guide
19
This is a new urgent/emergency message. It can be stored into RUIM Card Memory.
This is an old urgent/emergency message. It can be stored into RUIM Card Memory.
This is a new normal message. It can be stored into Phone Memory.
This is an old normal message. It can be stored into Phone Memory.
This is a new urgent/emergency message. It can be stored into Phone Memory.
This is an old urgent/emergency message. It can be stored into Phone Memory.
From the message view, you can choose to access the following options:
3.1.2.1 Reply
You can reply to the sender after opening the received message.
3.1.2.2 Forward
You can forward the received message to desired number.
3.1.2.3 Use number
If the Numbers available haven’t been stored into the contacts list, you can save it.
If the number has been stored into the contacts list, the phone displayed ‘This number
already exists’.
3.1.2.4 Erase
Allow you to erase the selected message.
3.1.3 Outbox
You may store sent messages and unsent messages to an outbox list according the MSG
Settings. You can retrieve these messages and forward them to other contacts, or resend
the message, or erase the message if it is no longer required. Erasing messages from the
outbox can free up additional memory on your phone.
You can Forward, Use number, Resend, Erase. For operation please refer to inbox menu.
3.1.4 Templates
You can set no more than 21 quick texts, in which 9 quick texts are by default other 12
quick texts can be edited by user.
Press up/down navigation key to scroll the desired message and press left soft key to
access the following options:
Edit: Allow you to modify the text and then save it.
Erase: Erase the selected quick text.
Add new: Enter the text-editing interface and then save it.
Send: You can send the selected quick text.

CG608 User Guide
20
3.1.5 Erase Msg
Access the Erase messages option to specify exactly which type of message you want to
erase.
By selecting Inbox, you can erase messages from the inbox folder.
By selecting Outbox, you can erase messages from the outbox folder.
By selecting Erase all read messages; you can erase all the read messages.
By selecting Erase all, you can quickly erase all messages stored in your phone and
RUIM card memory.
3.1.6 Voice mail
If you subscribe to voice mail, your service provider will furnish you with a voice mailbox
number. You need to save this number to your phone to use voice mail. By setting the call
forwarding function, the incoming call is forwarded to your voice mail.
When you receive a voice message, your phone starts beeping or displays a message, or
both. If you receive more than one message, your phone shows the number of messages
received.
Listening to voice messages, the user needs to press and hold the key 1 (Default speed
dial for Key 1 is Voice mail).
Note: This function needs to be supported by your network
3.1.7 Settings
You can change the message settings in this menu.
3.1.7.1 Auto save
Allow you to select ‘On’ or ‘Off’ option. If you select 'On' option, your phone will save the
sent or unsent messages in the Outbox (subject to memory available).
3.1.7.2 Auto delete
Allow you to select ‘On’ or ‘Off’ option. If you select 'On' option, the messages in the
Outbox are deleted automatically when the memory becomes full.
3.1.7.3 Priority
The function allows you to select Normal, Urgent or Emergency.
3.1.7.4 Validity period
Allow you to select 'Default', '30 minutes', '1 hour', '2 hours', '12 hours', '1 day', '2 days', '3
days' options. You can set the validity period for your messages, that is, how long they
should be available to the receiver.