TRENDnet TE100-PCI User manual

Fiber Ethernet Adapter
User’s Guide 1
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Preface
This manual describes how to install and use the Fiber Ethernet
Adapter. This Fiber Adapter allows options of different fiber
connections, such as connector types and segment distance.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
• Introduction on Fiber Adapter
• Product features
• LEDs functions
• Hardware installation
• Software installation
• Specifications

Fiber Ethernet Adapter
2 User’s Guide
Table of Contents
PREFACE ...............................................................................1
TABLE OF CONTENTS ...........................................................2
PRODUCT OVERVIEW ...........................................................3
FIBER ETHERNET ADAPTER ..........................................................3
PACKAGE CONTENTS....................................................................3
PRODUCT FEATURES ....................................................................4
Driver Support.................................................................................................5
5Software Support..........................................................................................5
LEDs...............................................................................................................6
HARDWARE INSTALLATION .................................................7
INSTALLING FIBER ADAPTER INTO PCI SLOT ..................................7
CONNECTING REMOTE WAKE-UP CABLE .......................................9
CONNECTING TO YOUR NETWORK...............................................10
Cabling Requirements ..................................................................................11
SOFTWARE INSTALLATION.................................................12
DIAGNOSTIC SOFTWARE .............................................................12
About Hardware’s Configuration...................................................................13
Run Diagnostics ...........................................................................................14
LOADING NETWORK DRIVERS......................................................15
Quick List for Supported Network Drivers ....................................................16
SPECIFICATIONS .................................................................17
ORDERING INFORMATION ..................................................18

Fiber Ethernet Adapter
User’s Guide 3
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Product Overview
Fiber Ethernet Adapter
Figure 1: Adapters with SC (left) and ST (right) connectors, featuring two LEDs
Package Contents
When you unpack the product package, you shall find the items
listed below. Please inspect the contents, and report any apparent
damage or missing items immediately to our authorized reseller.
Fiber Adapter
 User’s Guide
3-wire cable (for Wake On LAN)
Driver Diskette

Fiber Ethernet Adapter
4 User’s Guide
Product Features
• Provide a variety of fiber connections:
SC, ST, MT-RJ or VF-45 connectors for multi-mode, and
SC connector for single-mode
• Support 32-bit Bus Master operation
• PCI bus clock speed range from 16.75 to 40 MHz
• Support Wake-On-LAN (WOL) function and remote
wake-up
• Support half-duplex or full-duplex operation for up to
200Mbps data transfer rate
• Compliant with PCI plug-and-play
• Compliant with IEEE 802.3u 100BASE-FX
• Compliant with PCI Specifications Revision 2.1
• Low CPU utilization
• Status LEDs

Fiber Ethernet Adapter
User’s Guide 5
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Driver Support
The Fiber Adapter supports a wide range of drivers for commonly
used network operating systems:
• NDIS2 (DOS, OS/2, LANtastic, WFW3.1…)
• NDIS for Win95, 98, NT 3.51, 4.0, 5.0 WFW3.11
• NetWare ODI driver for DOS, OS/2, and NetWare
3.x, 4.x, 5.0 Server
• SCO Unix driver
• Linux driver
Note: Win2000 driver (RTL8139 A/B/C/8130 Series Adapter)
is bundled with Win2000.
Software Support
• Setup/Diagnostic Program for DOS
(REST8139.EXE in DIAG directory)
Note: RSET8139.EXE is a DOS only application. It may not
run properly under the DOS prompt in Windows.

Fiber Ethernet Adapter
6 User’s Guide
LEDs
cLNK Link
This LED comes on when a network connection is established
successfully.
dACT Activity
This LED flashes when the port is transmitting or receiving data.
LEDs Status Indication
Steady A valid network connection established.
LNK stands for LINK.
LNK
Off Disconnection.
Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
ACT
Off No activity.

Fiber Ethernet Adapter
User’s Guide 7
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Hardware Installation
Installing Fiber Adapter into PCI slot
Step 1: Turn off the power to the PC.
Step 2: Remove any metal decorations from your hands and wrists.
Step 3: Remove the cover from your PC.
Step 4: Locate an empty, non-shared bus mastering 32-bit PCI slot and remove
the corresponding backplate. Save the screw for use in Step 6.
<Note>
i. Do not install the Fiber Adapter in a shared PCI slot. Avoid any PCI slot next to
an ISA slot because this is often a shared slot and does not support bus
mastering.
ii. If you are going to install the Remote Wake-Up cable, choose an available
PCI slot most close to the 3-pin Remote Wake-Up connector on the PC
motherboard.
iii. If you have problems in identifying a suitable slot, check your PC
documentation or ask your system administrator for help.
Step 5: Carefully insert the Fiber Adapter into the chosen slot and press firmly
with proper push to ensure it is fully seated in the slot.
Step 6: Secure the Fiber Adapter with the screw you saved in step 4.
<Note>
If you wish to use the Remote Wake-Up function, please complete the
installation in next section “Connecting the Remote Wake-Up Cable” before
proceeding to step 7.
Step 7: Replace the PC cover.
Step 8: Proceed to “Connecting to Your Network” section.

Fiber Ethernet Adapter
8 User’s Guide
Install the FiberAdapterinto the PCIslot
and screwit onto the backplate
Figure 2: Installing Fiber Adapter into 32-bit PCI slot
<Note>
Always ensure the power is cut off before any installation to avoid electric
shock and possible damage to the equipments.

Fiber Ethernet Adapter
User’s Guide 9
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Connecting Remote Wake-Up Cable
This is an optional function. Proceed with the installation only
when your PC supports this Remote Wake-Up and you wish to
make use of this function. Please check your Motherboard User’s
Guide for more information.
Step 1: Make sure the power to the PC is off.
Follow Step 1~3 in previous section.
Step 2: Check if the Fiber Adapter is properly installed in a PCI slot.
Step 3: Prepare a Remote Wake-Up cable. Connect the cable from Fiber
Adapter to motherboard connector. Refer to Figure 3 below for details.
Step 4: Replace the PC cover then.
Step 5: Proceed to “Connecting to Your Network” Section.
Connect Remote Wake-Up cable from FiberAdapter
to motherboard connector
Pl u g i n Re m o t e Wa ke - Up c a b l e
to c onnec tor on Fiber Ada pter
Figure 3: Connecting Wake-Up cable

Fiber Ethernet Adapter
10 User’s Guide
Connecting to Your Network
This section describes how to connect the Fiber Adapter to a 100
Mbps fiber-based Ethernet network, which contributes to its
optimal performance.
<Note>
You must connect the Fiber Adapter to the network before installing the
network driver.
Step 1: Remove the protective covers from the Fiber Adapter’s connector.
Step 2: Prepare a network cable with corresponding connectors for the two end
devices, one end to the Fiber Adapter and the other to a 100Mbps fiber
port on the network hub or switch.
Step 3: Connect the network cable to the connector on the Fiber Adapter. This
network cable consists of two individual cables: one for ‘transmission
(TX)’, and the other for ‘reception (RX)’. Refer to Figure 4 for details.
Step 4: Connect the other end of the network cable to a 100BASE-FX hub or a
switch.
<Note>
i. Insert the cable that is connected to the transmit (TX) connector on the Fiber
Adapter into the receive (RX) connector on the network hub or switch.
ii. Insert the cable that is connected to the receive (RX) connector on the Fiber
Adapter into the transmit (TX) connector on the network hub or switch.
Step 5: When the cable is properly connected to two end devices, turn on the
power to the PC.
Step 6: Check the LNK (Link) LED. The LED will come on when the Fiber
Adapter is receiving a good link signal from the connected device, a hub
or switch.
Step 7: Proceed to next section for installing the network driver.

Fiber Ethernet Adapter
User’s Guide 11
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Cabling Requirements
For cabling requirements and maximum segment distance when
connecting the Fiber Adapter to your network, please refer to the
Ordering Information on page 18.
TX c o n n e c t o r
Insert the otherend of c able
into the 'rec eive' (RX)c onnector
on network hub orswitch
RX c o n n e c t o r
Insert the otherend of cable
into the 'transmit' (TX) connec tor
on network hub orswitc
h
(SC type connector fiber cable)
Figure 4: Connecting to your network

Fiber Ethernet Adapter
12 User’s Guide
Software Installation
Diagnostic Software
The program (RSET8139.exe) provided in the software diskette is 1)
to set up the Fiber Adapter’s hardware configuration, and 2) for
diagnostic purpose.
Step 1: Execute the program. This program MUST be run under pure DOS.
Press <SPACE> to continue.
Step 2: The Main Menu is as shown below:

Fiber Ethernet Adapter
User’s Guide 13
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
About Hardware’s Configuration
Step 1: Choose “View Current Configuration” from the Main Menu and press
<ENTER> to view the adapter’s current configuration.
Step 2: If you want to change the current configuration, choose “Set Up New
Configuration” from the Main Menu and press <ENTER> to proceed.
Step 3: Choose “Media Type” and press <ENTER>. For the Fiber Adapter, you
can only select [Auto Detect], [100 Full] or [100 Half] from the “Media
Type” selection. The adapter will not function when selecting [10 Full] or
[10 Half].
Step 4: Choose “Boot ROM Size” and press <ENTER>. Select [Boot Enabled]
or [Boot ROM Disabled]. Note: We do not provide Boot ROM.
Step 5: Same steps for “Flow Control”, “Wake On LAN”, “Link Change” and
“LAN Wake Signal”: Choose, select, <ENTER>, and <ESC> to exit.

Fiber Ethernet Adapter
14 User’s Guide
Run Diagnostics
Step 1: Choose “Run Diagnostics” from the Main Menu. Press <ENTER>.
Step 2: Select a test or diagnostics, and press <ENTER> to run:
--> Run EEPROM Test
--> Run Diagnostics On Board
--> Run Diagnostics On Network (requires twoTE100PCIFXplus on the
same network. Set one as “Initiator” and the other as “Responder”).
--> Run Power Management Test (also requires two TE100PCIFXplus.
Set one as Target and then power down the computer to “power down
mode. Set the other as Master, specifies the target machine’s Node ID
(MAC address), and send magic packet or wake-up frame to remotely
wake up the target machine.
Step 3: Press <ESC> to exit.
<Note>
i. This program MUST be run under pure DOS mode.
ii. This program MUST run without any network driver installed to prevent any error.
iii. Hit F1 key for additional help.

Fiber Ethernet Adapter
User’s Guide 15
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Loading Network Drivers
The Fiber Adapter is shipped with one software diskette enclosed.
The following drivers are provided in the diskette:
• NDIS2 (DOS, OS/2, LANtastic, WFW3.11…)
• NDIS for Win95, 98, NT 3.51, 4.0, 5.0, WFW3.11
• NetWare ODI driver for DOS, OS/2, and NetWare
3.x, 4.x, 5.0 Server
• SCO Unix driver
• Linux driver
Note: Win2000 driver (RTL8139 A/B/C/8130 Series Adapter) is
bundled with Win2000.
Below is a quick list showing the path for supported drivers and
text files. Please refer to the text files for installation details.
Step 1: Find the suitable network driver for the platform that you are using.
Carefully read the text file for that driver.
Step 2: Follow the step-by-step instruction in the text file to load the driver.
For Windows 95, 98 or NT, it takes only a few clicks to complete the
driver installation of the Fiber Adapter. Please make sure Windows
copies driver from the correct directory on the diskette.
<Note>
The Fiber Adapter doesn’t support 10BASE-FL standard, and therefore, if you
select through the software to force the speed at 10Mbps, the Fiber Adapter
will fail to function. That is, the Fiber Adapter can only work at 100Mbps speed.

Fiber Ethernet Adapter
16 User’s Guide
Quick List for Supported Network Drivers
Network OS Text File
Path
Driver Path
Windows NT 3.51 \Winnt\Msnt.txt \Nt351\RTL8139.SYS
Windows NT 4.0 \Winnt\Msnt.txt \Winnt\RTL8139.SYS
Windows 95 NDIS3 OSR2 \W95osr2\Netrts.inf \W95osr2\RTL8139.SYS
Windows 98 NDIS5 \Win98\Win98.txt \Win98\RTL8139.SYS
Windows for Workgroups 3.1 NDIS2 \Ndis2\Ndis.txt
\Ndis2\Wfw.txt
\Ndis2\Dos\RTSND.DOS
Microsoft Network Client 3.0 \Ndis2\Ndis.txt
\Ndis2\Msclient.txt
\Ndis2\Dos\RTSND.DOS
LAN Manager 2.0 \Ndis2\Ndis.txt
\Ndis2\Lanman.txt
\Ndis2\Dos\RTSND.DOS
Banyan VINES \Ndis2\Ndis.txt
\Ndis2\Banyan.txt
\Ndis2\Dos\RTSND.DOS
ARTISOFT LANtastic 5.0, 6.0 \Ndis2\Ndis.txt
\Ndis2\Lantasti.txt
\Ndis2\Dos\RTSND.DOS
DEC PATHWORKS \Ndis2\Ndis.txt
\Ndis2\Pathwork.txt
\Ndis2\Dos\RTSND.DOS
Sun PC-NFS \Ndis2\Ndis.txt
\Ndis2\Pcnfs.txt
\Ndis2\Dos\RTSND.DOS
IBM LAN Server (DOS) \Ndis2\Ndis.txt
\Ndis2\Lansvr.txt
\Ndis2\Dos\RTSND.DOS
IBM LAN Server (OS/2) \Ndis2\Ndis.txt
\Ndis2\Lansvr.txt
\Ndis2\Os2\RTSND.OS2
Mac OS \Macos\Install.txt \Macos\RTL8139.SIT
Microsoft LAN Manager (DOS) --- \Mslanman.dos\Drivers\Ethernet\
RTL8139\RTSND.DOS
Microsoft LAN Manager (OS/2) --- \Mslanman.os2\Drivers\Ethernet\
RTL8139\RTSND.OS2
Netware Server 3.12, 4.10, 4.11, 5.0
Netware Client (DOS)
Netware Client (OS/2)
\Netware\Readme.txt
---
---
\Netware\RTSSRV.LAN
\Netware\Dosodi\RTSODI.COM
\Netware\Os2odi\RTSOS2.SYS
Netware Client 32 for DOS &
Microsoft Windows 3.x
\Netware\Readme.txt \Netware\RTSSRV.LAN
Netware Client 32 for Microsoft
Windows 95 OSR2
\Netware\Readme.txt \Netware\RTSSRV.LAN
Linux \Linux\Linux.txt \Linux\RTL8139.c
SCO UnixWare 7.x \Unixware.7\Install.txt \Unixware.7\RTSPKG.TAR
SCO Unix 4.x \Sco\Sco4.txt \Sco\4.x\DRIVER.O
SCO Unix 5.x \Sco\Sco5.txt \Sco\5.x\8139.VOL

Fiber Ethernet Adapter
User’s Guide 17
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Specifications
Applicable Standards IEEE 802.3u 100BASE-FX
PCI Specifications Revision 2.1
Speed
100BASE-FX:
200Mbps full-duplex
100Mbps half-duplex
Performance 148,800pps for 100Mbps
Fiber Cable 62/125µm multi-mode fiber-optic
cable, up to 2 km
10/125µm single-mode fiber-optic
cable, up to 75 km
Wavelength 1300nm
LED Indicators LNK (Link) /ACT (Activity)
Dimensions 136 mm × 89 mm
Net Weight 90g approx.
Power Consumption 5VDC, 500mA max.
Operating Temperature 0°C to 40° C (32°F to 104°F)
Storage Temperature -25°C to 70°C (-13°F to 158°F)
Humidity 10%-90% non-condensing
Emissions FCC part 15 Class B,
CE Mark Class B, VCCI Class B

Fiber Ethernet Adapter
18 User’s Guide
Ordering Information
Please indicate the desired connector type and connection distance
when ordering.
Connector
Type on
Fiber Adapter
Wavelength of 1300nm
Fiber Optic required
Maximum Distance
(* full-duplex)
ST Multi-mode, 62/125 µm 2 km
SC Multi-mode, 62/125 µm 2 km
VF-45 Multi-mode, 62/125 µm 2 km
MT-RJ Multi-mode, 62/125 µm 2 km
SC Single-mode, 10/125 µm 15 km
SC Single-mode, 10/125 µm 40 km
SC Single-mode, 10/125 µm 75 km
<Note>
The maximum node-to-node network distance is in full-duplex operation.