TRENDnet TU2-ETG User manual

i
Table of Contents
1. Introduction.........................................................................................................1
Features.............................................................................................................................1
Package Contents..............................................................................................................1
System Requirements........................................................................................................1
LED Status........................................................................................................................2
2. Installation ...........................................................................................................3
Driver Installation.............................................................................................................3
Verifying the Driver Installation in Windows...................................................................7
Connecting to a Network ..................................................................................................7
Configuring Network Settings..........................................................................................8
Windows XP/2000.....................................................................................................................8
Windows ME/98SE ...................................................................................................................9
3. Specifications....................................................................................................10

1
1. Introduction
The USB 2.0 Gigabit Ethernet Adapter instantly adds advanced network adapter to
your desktop or laptop PC. The adapter supports Windows-based desktop
computers or notebook PCs with a USB 1.0, 1.1 or 2.0 ports. It auto-senses
between 10, 100 and 100Mbps network speeds. The adapter’s Auto-MDIX feature
allows you to use a straight-through or crossover Ethernet cable. Its bus-powered
design eliminates the need for an external power adapter. This device allows you to
connect at Gigabit speeds using your computer’s existing USB ports.
Features
Compliant with USB 2.0 and 1.1 specifications
Compliant with IEEE 802.3, 802.3u and 802.3ab standards
Auto Negotiation & Auto-MDIX RJ-45 Gigabit Port
Supports both full-duplex and half-duplex operations
Supports Suspend mode and Hibernate mode to remotely wake-up through
link-up or magic packet
Compliant with Windows 98SE/ME/2000/XP
Powered by USB port. No external power adapter required
Diagnostic LEDs
Plug & Play
2-Year Warranty
Package Contents
Before installation, please check the items of the package.
TU2-ETG
Driver CD-ROM
Multi-Language Quick Installation Guide
System Requirements
CPU: 300MHz or Above
Memory: 256MB RAM or above
Windows®98SE/ME/2000/XP

2
LED Status
LED Color Status Description
Off Link is not established.Link Green
On Link is established.
Off Link is not established
Link to 10/100Mbps network.
On Link to 1000Mbps network.
1000Mbps Green
Blinking There is 1000Mbps traffic flow over the network.

3
2. Installation
Driver Installation
Note: DO NOT connect the Ethernet adapter to your computer before completing
the driver installation.
1. Insert the provided CD into your CD-ROM drive. The setup program will start
automatically. If not, locate and double-click the Setup.exe file in the Driver
folder to launch the setup program.
2. Select Complete and click Next.

4
3. Click Install to start the installation.
4. Click Finish when the installation is complete.
5. Select Yes, I want to restart my computer now and click Finish to reboot
your computer.
6. After reboot, connect the Ethernet adapter’s USB end to a free USB port of your
computer. At this stage, different situations may occur according to your
operation system. Follow the instructions below to complete the installation.

5
Windows XP
1. When the Found New Hardware Wizard screen appears, select Install the
software automatically (Recommended) and click Next.
2. If compatibility message appears, just click Continue Anyway.
3. Click Finish to complete the installation.

6
Windows 2000
If Digital Signature Not Found window appears, just click Yes.
Windows ME
Just wait the system to complete the installation.
Windows 98SE
Upon your USB device connection, if the system prompts you for the Windows
98SE CD-ROM, click OK. Remove the provided CD and insert the Windows 98SE
CD-ROM. Then click OK again.

7
Verifying the Driver Installation in Windows
To verify your Ethernet adapter installation, select Control Panel > System >
(Hardware) > Device Manager. In the Network adapters group, a string similar to
USB2.0 to Gigabit Ethernet Adapter should be displayed.
If there is a question or exclamation mark next to that item, then the driver is not
properly installed. Please delete the item and repeat the installation steps.
*The example screenshot is taken from Windows XP.
Connecting to a Network
Now you can connect your network to the device’s LAN port. The LAN port
supportsAuto-MDIX feature. It eliminates the need to use crossover cables.
Upon your connection, a message pops up in the notification area indicating your
connection speed.
The adapter’s AutoSense feature can automatically detect the network's maximum
line speed. To have a 1000Mbps connection, your network device (e.g., switch,
router or DSL modem) must also support 1000Mbps.

8
Configuring Network Settings
You should configure your Ethernet adapter as required according to your network
environment. If you are unsure about the settings, consult your network
administrator for assistance. The following describes how to launch the network
settings window for your Ethernet adapter.
Windows XP/2000
After the installation, a local area connection icon is automatically created for your
Ethernet adapter in the Network Connections folder. You can access Network
Connections folder by selecting Start > Settings > Control Panel > Network and
Internet Connections.
In the Network Connections folder, double-click the connection icon for your
adapter. Then the Local Area Connection Properties window appears.