TRENDnet TEG-PCBUSR User manual

Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEG-PCBUSR
Version 07.27.05
Gigabit Ethernet PC Card Adapter
Quick Installation Guide
Gigabit Ethernet PC Card Adapter
Ghid de Instalare rapida

Table of Contents
English ................................................................................. 1
1
2
3
4
14
17
17
18
19
20
30
1. Prepare for Installation ..................................................
2. Product Detail ................................................................
3. Hardware Installation .....................................................
4. Driver Installation ...........................................................
5. Verify Installation ...........................................................
1. Pregatiti-va pentru instalare ...........................................
2. Detalii Produs ..............................................................
3. Instalarea Hardware .....................................................
4. Instalarea Driverelor ......................................................
5. Verificarea Instalarii .......................................................
Troubleshooting ....................................................................
34
Românǎ .........................................................................................

Thank you for purchasing TRENDnet's TEG-PCBUSR Gigabit Ethernet PC
Card Adapter.
This guide will help you set up your Gigabit Ethernet PC Card Adapter.
Following the installations should be quick and easy. If you run into problems,
please refer to the Troubleshooting section. If you need further technical
support, please visit www.TRENDNET.com or call technical support by phone.
Verify Package Contents
Please make sure you have everything in the box:
1
1. Prepare for Installation
English QIG
English
Minimum System Requirements
1. Pentium 266Mhz or faster processor
2. 64MB RAM or more
3. Available 32-bit CardBus Type II slot
4. Windows XP, 2000, ME, 98SE, Microsoft Network Client for DOS (NDIS 2
driver), or NetWare Client for DOS (ODI driver)
TEG-PCBUSR Quick Instllation Guide Driver CD-ROM
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEG-PCBUSR
Version 07.27.05
Gigabit Ethernet PC Card Adapter
Quick Installation Guide
Gigabit Ethernet PC Card Adapter
Ghid de Instalare rapida

2
2. Product Detail
The Gigabit Ethernet CardBus Adapter has a RJ-45 connector, and two LEDs
that indicate data rate and network activity.
English
RJ-45
connector
LED that indicates
data rate
LED that indicates
network activity

3
3. Hardware Installation
English
1. Boot up your laptop PC and make sure Windows's Desktop is properly
loaded.
2. Insert the TEG-PCBUSR into an available PC Card slot.
3. Make sure the TEG-PCBUSR is inserted all the way to the end of the slot.
4. Your laptop should emit a beeping sound that indicates newly installed
hardware.

4English
4. Driver Installation
After inserting the TEG-PCBUSR, the “Found New Hardware Wizard” will
appear. Windows will automatically detect and ask you to install the Gigabit
Ethernet Driver for the TEG-PCBUSR.
1. Insert the TEG-PCBUSR Driver CD-ROM into your computer's CD-ROM
drive.
2. Click Install from a list or specific location (Advanced). Click Next.
3. Click Search for the best driver, click location:, and type a:\winxp in the
text box. Click Next.
Windows XP

5English
4. NOTE: TRENDnet's Gigabit Ethernet PC Card has been fully tested under all
supported Windows Operating Systems and has been approved for their
functionality; click Continue Anyway.
5. Click Finish.
Your driver installation is now complete.
NOTE: If you would like to verify the TEG-PCBUSR has been installed
properly for your windows, go to the Verify Installation section.

6English
After inserting the TEG-PCBUSR, the “Found New Hardware Wizard” will
appear. Windows will automatically detect and ask you to install the Gigabit
Ethernet Driver for the TEG-PCBUSR.
1. Insert the TEG-PCBUSR Driver CD-ROM into your computer's CD-ROM
drive.
2. Click Next.
Windows 2000
3. Click Search for a suitable driver for my device (recommended). Click
Next.

7English
4. Click Specify a location. Click Next.
5. Type a:\win2k in the text box. Click OK.
6. Click Next.

8English
7. Click Yes.
8. Click Finish.
Your driver installation is now complete.
NOTE: If you would like to verify the TEG-PCBUSR has been installed
properly for your windows, go to the Verify Installation section.