TRENDnet TEW-633GR - Wireless Router User manual

1

2
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
TRENDnet declares that TEW-633GR (FCC ID: S9ZTEW633GR) is limited in CH1~CH11 for 2.4
GHz by specified firmware controlled in U.S.A.
Copyright
This publication, including all photographs, illustrations and software, is protected under interna-
tional copyright laws, with all rights reserved. Neither this manual, nor any of the material con-
tained herein, may be reproduced without written consent of the author.
Copyright 2006
Trademark recognition
All product names used in this manual are the properties of their respective owners and are
acknowledged.

3
Table of Contents
Getting Started with the TEW-633GR 4
PackageContents 5
Minimum System Requirements 5
Wireless LAN Networking 6
Introduction 9
Features 9
Hardware Overview 10
Side Panel 10
LEDs 11
Installation Considerations 12
Getting Started 12
Using the Configuration Menu 13
Basic 14
Advanced 24
Tools 55
Status 69
Glossary 80
Note: Please run the CD and follow the steps in the Quick Installation Guide to setup your
router. If you still have problems after doing so then proceed to the User’s Guide to install
the router with web-based configuration.

4
Getting Started with the TEW-633GR
Congratulations on purchasing the TEW-633GR! This manual provides information for setting up
and configuring the TEW-633GR. This manual is intended for both home users and professionals.
The following conventions are used in this manual:
THE NOTE SYMBOL INDICATES ADDITIONAL INFORMATION ON THE
TOPIC AT HAND.
THE TIP SYMBOL INDICATES HELPFULL INFORMATION AND TIPS TO
IMPROVE YOUR NETWORK EXPERIENCE.
THE CAUTION SYMBOL ALERTS YOU TO SITUATIONS THAT MAY
DEGRADE YOUR NETWORKING EXPERIENCE OR COMPROMISE
LIKE NOTES AND TIPS, THE IMPORTANT SYMBOL INDICATES
INFORMATION THAT CAN IMPROVE NETWORKING. THIS INFORMATION
SHOULD NOT BE OVERLOOKED.

5
Package Contents
zTEW-633GR 11n Wireless N Gigabit Router
zCAT-5 Ethernet Cable
zPower Adapter
zUser’s Guide CD-ROM
zMulti-Language Quick Installation Guide
Using a power supply with a different voltage than the one included with your
product will cause damage and void the warranty for this product.
Minimum System Requirements
zEthernet-Based Cable or DSL Modem
zComputers with Windows, Macintosh, or Linux-based operating systems with an installed
Ethernet adapter and CD-ROM Drive
zInternet Explorer Version 6.0 or Netscape Navigator Version 7.0 and Above

6
Wireless LAN Networking
This section provides background information on wireless LAN networking technology. Consult
the Glossary for definitions of the terminology used in this section.
THE INFORMATION IN THIS SECTION IS FOR YOUR REFERENCE. CHANGING
NETWORK SETTINGS AND PARTICULARLY SECURITY SETTTINGS SHOULD ONLY
BE DONE BY AN AUTHORIZED ADMINISTRATOR.
Transmission Rate (Transfer Rate)
The TEW-633GR provides various transmission (data) rate options for you to select. In most
networking scenarios, the factory default Best (automatic) setting proves the most efficient. This
setting allows your TEW-633GR to operate at the maximum transmission (data) rate. When the
communication quality drops below a certain level, the TEW-633GR automatically switches to a
lower transmission (data) rate. Transmission at lower data speeds is usually more reliable.
However, when the communication quality improves again, the TEW-633GR gradually increases
the transmission (data) rate again until it reaches the highest available transmission rate.
Types of Wireless Networks
Wireless LAN networking works in either of the two modes: ad-hoc and infrastructure. In infra-
structure mode, wireless devices communicate to a wired LAN via access points. Each access
point and its wireless devices are known as a Basic Service Set (BSS). An Extended Service Set
(ESS) is two or more BSSs in the same subnet. In ad hoc mode (also known as peer-to-peer
mode), wireless devices communicate with each other directly and do not use an access point.
This is an Independent BSS (IBSS).
To connect to a wired network within a coverage area using access points, set the operation mode
to Infrastructure (BSS). To set up an independent wireless workgroup without an access point, use
Ad-hoc (IBSS) mode.
AD-HOC (IBSS) NETWORK
Ad-hoc mode does not require an access point or a wired network. Two or more wireless stations
communicate directly to each other. An ad-hoc network may sometimes be referred to as an
Independent Basic Service Set (IBSS).
To set up an ad-hoc network, configure all the stations in ad-hoc mode. Use the same SSID and
channel for each station.

7
When a number of wireless stations are connected using a single access point, you have a Basic
Service Set (BSS).
In the ESS diagram below, communication is done through the access points, which relay data
packets to other wireless stations or devices connected to the wired network. Wireless stations
can then access resources, such as a printer, on the wired network.

8
In an ESS environment, users are able to move from one access point to another without losing the
connection. In the diagram below, when the user moves from BSS (1) to BSS (2) the WLAN client
devices automatically switches to the channel used in BSS (2).
Roaming in an ESS network diagram

9
Introduction
The TEW-633GR 11n Wireless Gigabit Router is a high-performance, wireless router that supports
high-speed wireless networking at home, at work or in public places.
Unlike most routers, the TEW-633GR provides data transfers at up to 300Mbps when using 11n (Draft
2.0) connection. This router is also back compatible with 802.11g or 11b devices. This means that you
do not need to change your entire network to maintain connectivity. You may sacrifice some of 11n’s
speed when you mix 11n and 11b/g devices, but you will not lose the ability to communicate when you
incorporate the 11n (Draft 2.0) standard into your 11b/g network. You may choose to slowly change
your network by gradually replacing the 11b/g devices with 11n devices.
Features
¾Wi-Fi Compliant with IEEE 802.11n (Draft 2.0) and IEEEE 802.11b/g Standards
¾2.412 to 2.484GHz frequency band operation
¾Compliant with IEEE 802.3 & 3u standards
¾Support 4 10/100/1000Mbps Gigabit LAN ports and 1 10/100/1000Mbps Gigabit WAN port
¾High-Speed up to 300Mbps Data Rate using IEEE 802.11n (Draft 2.0) connection
¾Supports Cable/DSL Modems with Dynamic IP, Static IP, PPPoE, PPTP, L2TP or BigPond
Connection Types
¾Firewall features Network Address Translation (NAT), and Stateful Packet Inspection (SPI)
protects against Dos attacks
¾Traffic Control with Virtual Server (max 24 configurable servers) and DMZ
¾UPnP (Universal Plug & Play) and ALGs Support for Internet applications such as Email, FTP,
Gaming, Remote Desktop, Net Meeting, Telnet, and more
¾Provides Additional Security of Enable/Disable SSID, Internet Access Control (Services, URL and
MAC Filtering)
¾Supports Multiple and Concurrent IPSec, L2TP and PPTP VPN Pass-Through Sessions
¾Flash Memory for Firmware Upgrade, Save/Restore Settings
¾Easy Management via Web Browser (HTTP) and Remote Management
¾Supports 64/128-bit WEP(for 11b/g), WPA/WPA2, and WPA-PSK/WPA2-PSK
¾Compliant with Windows 98/NT/2000/XP/2003 Server/Vista, Linux and Mac OS
¾Support 4 x 10/100Mbps Auto-MDIX LAN Port and 1 x 10/100Mbps WAN Port (Internet)
¾3 External Fixed Antennas to support high speed performance and great coverage
¾Easy wireless setup via WiFi Protection Setup (PIN).

10
¾Hardware Overview
Side Panel
DC-IN
The DC power input connector is a single jack socket to supply power to the TEW-633GR.
Please use the Power Adapter provided on the TEW-633GR package.
Reset Button
Pressing the reset button restores the router to its original factory default settings.
Auto MDI/MDIX Gigabit WAN Port
This is the connection for the Ethernet cable to the Cable or DSL modem
Auto MDI/MDIX Gigabit LAN Ports
These ports automatically sense the cable type when connecting to Ethernet-enabled computers.