TRENDnet TEW-692GR User manual

1

2
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
The availability of some specific channels and/or operational frequency bands are country
dependent and are firmware programmed at the factory to match the intended destination. The
firmware setting is not accessible by the end user.

3
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test
methods have been applied in order to prove presumption of conformity with the essential requirements of
the R&TTE Directive 1999/5/EC:
- EN60950-1:2006+A11: 2009
Safety of Information Technology Equipment
- EN 62311:2008
- Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for
wireless telecommunication systems with the basic restrictions or the reference levels related to human
exposure to radio frequency electromagnetic fields (110MHz - 40 GHz) - General public
- EN 300 328 V1.7.1: (2006-10)
- Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems;
Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation
techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive
- EN 301 489-1 V1.8.1: (2008-04)
- Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services; Part 1: Common technical requirements
- EN 301 489-17 V2.1.1:( 2009-05)
- Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC)
standard for radio equipment; Part 17: Specific conditions for 2,4 GHz wideband transmission systems, 5
GHz high performance RLAN equipment and 5,8 GHz Broadband Data Transmitting Systems
-
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member
states and EFTA countries, except in France and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain
authorization to use the device for setting up outdoor radio links and/or for supplying public access to
telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output
power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information
the end-user should contact the national spectrum authority in France.

4
Česky
[Czech]
TRENDnet tímto prohlašuje, že tento TEW-692GR je ve shodě se základními
požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk [Danish]
Undertegnede TRENDnet erklærer herved, at følgende udstyr TEW-692GR overholder de
væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt TRENDnet, dass sich das Gerät TEW-692GR in
Übereinstimmung mit den grundlegendenAnforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab TRENDnet seadme TEW-692GR vastavust direktiivi
1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele
asjakohastele sätetele.
English
Hereby, TRENDnet, declares that this TEW-692GR is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente TRENDnet declara que el TEW-692GR cumple con los
requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles
de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ TRENDnet ΔΗΛΩΝΕΙ ΟΤΙ TEW-692GR ΣΥΜΜΟΡΦΩΝΕΤΑΙ
ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ
ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French]
Par la présente TRENDnet déclare que l'appareil TEW-692GR est conforme aux
exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
Italiano
[Italian]
Con la presente TRENDnet dichiara che questo TEW-692GR è conforme ai
requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
Latviski
[Latvian]
Ar šo TRENDnet deklarē, ka TEW-692GR atbilst Direktīvas 1999/5/EK
būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių
[Lithuanian]
Šiuo TRENDnet deklaruoja, kad šis TEW-692GR atitinka esminius reikalavimus
ir kitas 1999/5/EB Direktyvos nuostatas.

5
Nederlands
[Dutch]
Hierbij verklaart TRENDnet dat het toestel TEW-692GR in overeenstemming is
met de essentiële eisen en de andere relevante bepalingen van richtlijn
1999/5/EG.
Malti
[Maltese]
Hawnhekk, TRENDnet, jiddikjara li dan TEW-692GR jikkonforma mal-ħtiġijiet
essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, TRENDnet nyilatkozom, hogy a TEW-692GR megfelel a vonatkozó
alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski
[Polish]
Niniejszym TRENDnet oświadcza, że TEW-692GR jest zgodny z zasadniczymi
wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy
1999/5/EC.
Português
[Portuguese
]
TRENDnet declara que este TEW-692GR está conforme com os requisitos
essenciais e outras disposições da Directiva 1999/5/CE.
Slovensko
[Slovenian]
TRENDnet izjavlja, da je ta TEW-692GR v skladu z bistvenimi zahtevami in
ostalimi relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak]
TRENDnet týmto vyhlasuje, že TEW-692GR spĺňa základné požiadavky a všetky
príslušné ustanovenia Smernice 1999/5/ES.
Suomi
[Finnish]
TRENDnet vakuuttaa täten että TEW-692GR tyyppinen laite on direktiivin
1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen
mukainen.
Svenska
[Swedish]
Härmed intygar TRENDnet att denna TEW-692GR står I överensstämmelse med
de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår
av direktiv 1999/5/EG.
European Union Notice:
Radio products with the CE marking comply with the R&TTE Directive (1999/5/EC), the EMC
Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of
the European Community.
Compliance with these directives implies conformity to the following European Norms:
EN 60950 Product Safety
EN 300 328 Technical requirement for radio equipment
EN 301 489-1/-17 General EMC requirements for radio equipment
Trademark recognition
All product names used in this manual are the properties of their respective owners and are acknowledged.

6
Contents
Getting Started..........................................................................................................8
Package Contents..................................................................................................8
Minimum System Requirements............................................................................. 8
Introduction ...............................................................................................................9
Features.................................................................................................................9
Overview................................................................................................................. 10
Network Diagram: ................................................................................................ 10
Front Panel LEDs................................................................................................. 10
Rear panel ........................................................................................................... 10
Wireless Performance Considerations ..................................................................11
Using the Configuration Menu................................................................................. 12
Setup Wizard........................................................................................................... 13
Network................................................................................................................... 14
WAN Setting......................................................................................................... 14
LAN Setting.......................................................................................................... 17
QoS...................................................................................................................... 18
DHCP Client List .................................................................................................. 19
Wireless 2.4GHz..................................................................................................... 20
Basic.................................................................................................................... 20
Advanced............................................................................................................. 23
Security................................................................................................................ 24
WPS..................................................................................................................... 26
Station List........................................................................................................... 27
Wireless 5GHz........................................................................................................ 28
Basic.................................................................................................................... 28
Advanced............................................................................................................. 31
Security................................................................................................................ 32
WPS..................................................................................................................... 35
Station List........................................................................................................... 36
Advanced................................................................................................................ 37
DMZ..................................................................................................................... 37
Virtual Server ....................................................................................................... 39
Routing................................................................................................................. 40
Access Control..................................................................................................... 41
ALG...................................................................................................................... 42
Special Applications ............................................................................................. 43
Gaming ................................................................................................................ 44
Inbound Filter....................................................................................................... 45
Schedule.............................................................................................................. 46
Advanced Network............................................................................................... 47
Administrator........................................................................................................... 48

7
Management........................................................................................................ 48
Upload Firmware.................................................................................................. 49
Setting Management............................................................................................ 50
Time..................................................................................................................... 51
Status................................................................................................................... 52
Help ........................................................................................................................ 53
Appendix................................................................................................................. 54
Wireless LAN Networking..................................................................................... 54
Glossary............................................................................................................... 56
Specification............................................................................................................ 61
Limited Warranty..................................................................................................... 62

8
Getting Started
Congratulations on purchasing theTEW-692GR This manual provides information for setting up and
configuring the TEW-692GR. This manual is intended for both home users and professionals.
The following conventions are used in this manual:
PACKAGE CONTENTS
TEW-692GR
CD-ROM (User’s Guide)
Multi-Language Quick Installation Guide
Network cable
Power Adapter (12V, 1A)
Using a power supply with a different voltage than the one included with your product will cause damage
and void the warranty for this product. If any item is found missing or damaged, please contact your local
reseller for replacement.
MINIMUM SYSTEM REQUIREMENTS
Ethernet-Based Cable or DSL Modem
Computers with Windows, Macintosh, or Linux-based operating systems with an installed Ethernet
adapter and CD-ROM Drive
Internet Explorer Version 6.0 or Netscape Navigator Version 7.0 and Above

9
Introduction
TRENDnet’s 450Mbps Concurrent Dual Band Wireless N Router, model TEW-692GR, is the first router to
support 450Mbps speeds on both the 2.4GHz and 5GHz bands at the same time. This router’s raw
horsepower redefines wireless networking as we know it, to easily stream HD video through the home.
Gigabit Wide Area Network and Local Area Network ports transfer wired data fast. Embedded GREENnet
technology reduces port-based power consumption by up to 70%.
Advanced Multiple Input Multiple Output (MIMO) antenna technology reduces wireless dead spots. Wi-Fi
Protected Setup (WPS) connects other WPS supported wireless adapters at the touch of a button. WMM®
Quality of Service (QoS) technology prioritizes gaming, Internet calls, and video streams. Assign up to four
virtual networks on each wireless band and manage access control for IP addresses, website URLs, and
data protocols.
FEATURES
•4 x 10/100/1000Mbps Auto-MDIX LAN ports
•1 x 10/100/1000Mbps WAN port (Internet)
•Wi-Fi Protected Setup (WPS) button
•On/off power switch (EU Version)
•LED status indicators
•Compliant with IEEE 802.11n/b/g/a standards
•High-speed data rates of up to 450 Mbps using both 2.4 GHz and 5 GHz bands
•Enable/disable wireless functionality with the WLAN on/off toggle switch
•Compatible with most popular cable/DSL Internet Service Providers using Dynamic/Static IP, PPPoE,
L2TP, and PPTP connection
•Advanced firewall protection with Network Address Translation (NAT) support
•Advanced wireless security of up to WPA2-RADIUS
•DMZ support
•Wi-Fi Multimedia (WMM) Quality of Service (QoS) data prioritization
•Support for up to four virtual wireless networks (SSIDs) per wireless band
•Gaming Port Controls: supports opening multiple ports or a range of ports
•Internet Access Control with MAC, URL, Service Type, and IP Range filtering
•Internet Access Control Rule Scheduling: schedule access to websites, online video games, Internet
cameras and more for specific times through the week
•One touch wireless connection to wireless clients using the WPS button
•Easy setup via Web browser using the latest versions of Internet Explorer, FireFox, Safari, and Chrome
•Virtual server and Application Level Gateway (ALG) services for special Internet applications
•Universal Plug and Play (UPnP) for auto discovery and support for device configuration of Internet
applications
•Coverage up to 100 meters (330 ft.) indoor and 300 meters (980 ft.) outdoor (depends on the
environment)
•3- year limited warranty

10
Overview
NETWORK DIAGRAM:
FRONT PANEL LEDS
•PWR
•WAN
•LAN1
•LAN2
•LAN3
•LAN4
•Wireless
•Wireless
•WPS
•Reserve
REAR PANEL
•DC-IN
•POWER SWITCH( EU)
•WAN
•LAN1
•LAN2
•LAN3
•LAN4

11
WIRELESS PERFORMANCE CONSIDERATIONS
There are a number of factors that can impact the range of wireless devices.
1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at an angle. The
more material the signal has to pass through the more signal you will lose.
2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of a wireless
device. Position the wireless devices in a manner that will minimize the amount of obstructions between
them.
3. Building materials can have a large impact on your wireless signal. In an indoor environment, try to
position the wireless devices so that the signal passes through less dense material such as dry wall.
Dense materials like metal, solid wood, glass or even furniture may block or degrade the signal.
4. Antenna orientation can also have a large impact on your wireless signal. Use the wireless adapter’s site
survey tool to determine the best antenna orientation for your wireless devices.
5. Interference from devices that produce RF (radio frequency) noise can also impact your signal. Position
your wireless devices away from anything that generates RF noise, such as microwaves, radios and baby
monitors.
6. Any device operating on the 2.4GHz frequency will cause interference. Devices such as 2.4GHz cordless
phones or other wireless remotes operating on the 2.4GHz frequency can potentially drop the wireless
signal. Although the phone may not be in use, the base can still transmit wireless signal. Move the
phone’s base station as far away as possible from your wireless devices.
If you are still experiencing low or no signal consider repositioning the wireless devices or installing additional
access points. The use of higher gain antennas may also provide the necessary coverage depending on the
environment.
limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency)
noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:
1 Keep the number of walls and ceilings between the TEW-639GR and other network devices to a
minimum - each wall or ceiling can reduce your wireless products range from 3-90 feet (1-30 meters.)
Position your devices so that the number of walls or ceilings is minimized.
2 Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a
45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14
meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at
an angle) for better reception.
3 Building Materials can impede the wireless signal - a solid metal door or aluminum studs may have a
negative effect on range. Try to position wireless devices and computers with wireless adapters so that
the signal passes through drywall or open doorways and not other materials.
4 Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that
generate extreme RF noise.

12
Using the Configuration Menu
Whenever you want to configure your TEW-692GR, you can access the Configuration Menu
through your PC by opening the Web-browser and typing in the IP Address of the TEW-692GR.
The TEW-692GR’s default IP Address is http://192.168.10.1
•Open the Web browser.
•Type in the IPAddress of the Router (http://192.168.10.1 )
If you have changed the default IP Address assigned to the TEW-692GR, make sure
to enter the correct IP Address.
•Select admin in the User Name field.
•Default password is admin.
•Click OK.

13
Setup Wizard
Setup Wizard is an easy way to set up the TEW-692GRstep by step. The Wizard will guide
user’s to set up the TEW-692GR in just few steps.
To setup the router’s internet connection settings, click ‘Launch Internet Connection Setup
Wizard’ and follow Wizard to complete your setting.
Once the internet connection setup is completed, click “Launch Wireless Security Setup Wizard”
to configure the router’s wireless settings.

14
Network
WAN SETTING
There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and Russia
PPTP. If you are unsure of your connection method, please contact your Internet Service Provider.
WAN Connection Type
There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and Russia
PPTP. If you are unsure of your connection method, please contact your Internet Service Provider.
Static: Used when your ISP provides you a set IP address that does not change. The IP information is
manually entered in your IP configuration settings. You must enter the IP address, Subnet Mask,
Gateway, Primary DNS Server, and Secondary DNS Server. Your ISP provides you with all of this
information.
DHCP:A method of connection where the ISP assigns your IP address when your router requests one
from the ISP's server. Host Name: Some ISP's may check your computer's Host Name. The Host Name
identifies your system to the ISP's server.

15
PPPoE: Select this option if your ISP requires you to use a PPPoE (Point to Point Protocol over Ethernet)
connection. DSL providers typically use this option. This method of connection requires you to enter a
Username and Password (provided by your Internet Service Provider) to gain access to the Internet.
Reconnect Mode: Typically PPPoE connections are not always on. The router allows you to set the
reconnection mode. The settings are:
Always on: A connection to the Internet is always maintained.
On demand: A connection to the Internet is made as needed.
Manual: You have to open up the Web-based management interface and click the Connect button
manually any time that you wish to connect to the Internet.
Maximum Idle Time: Time interval the machine can be idle before the PPPoE connection is
disconnected. The Maximum Idle Time value is only used for the "On demand" and "Manual" reconnect
modes.
L2TP:L2TP (Layer Two Tunneling Protocol) uses a virtual private network to connect to your ISP. This
method of connection requires you to enter a Username and Password (provided by your Internet
Service Provider) to gain access to the Internet.
L2TP Server IP Address: The ISP provides this parameter, if necessary. The value may be the same
as the Gateway IP Address.
Reconnect Mode: Typically PPPoE connections are not always on. The router allows you to set the
reconnection mode. The settings are:
Always on: A connection to the Internet is always maintained.
On demand: A connection to the Internet is made as needed.
Manual: You have to open up the Web-based management interface and click the Connect button
manually any time that you wish to connect to the Internet.
Maximum Idle Time: Time interval the machine can be idle before the PPPoE connection is
disconnected. The Maximum Idle Time value is only used for the "On demand" and "Manual"
reconnect modes.
WAN Interface IP Type
Static: If your ISP has assigned a fixed IP address, select this option. The ISP provides the values for
the following fields for WAN Interface IP Setting: IP Address, Subnet Mask , Default Gateway.
Dynamic: If the ISP's servers assign the router's IP addressing upon establishing a connection, select
this option.
PPTP: PPTP (Point to Point Tunneling Protocol) uses a virtual private network to connect to your ISP.
This method of connection is primarily used in Europe. This method of connection requires you to enter
a Username and Password (provided by your Internet Service Provider) to gain access to the Internet.
PPTP Server IP Address: The ISP provides this parameter, if necessary. The value may be the same
as the Gateway IP Address.

16
Reconnect Mode: Typically PPPoE connections are not always on. The router allows you to set the
reconnection mode. The settings are:
Always on: A connection to the Internet is always maintained.
On demand: A connection to the Internet is made as needed.
Manual: You have to open up the Web-based management interface and click the Connect button
manually any time that you wish to connect to the Internet.
Maximum Idle Time: Time interval the machine can be idle before the PPPoE connection is
disconnected. The Maximum Idle Time value is only used for the "On demand" and "Manual"
reconnect modes.
WAN Interface IP Type
Static: If your ISP has assigned a fixed IP address, select this option. The ISP provides the values for
the following fields for WAN Interface IP Setting: IP Address, Subnet Mask , Default Gateway, and
optional for DNS Server
Dynamic: If the ISP's servers assign the router's IP addressing upon establishing a connection, select
this option.
Russia PPTP:The Russia PPTP can configure IP address on the WAN interface and establish PPTP to
get IP address, subnet mask, default gateway and DNS for ANOTHER logical IP interface on WAN port.
So the physical WAN port will have 2 logical IP interfaces and can communicate with internal ISP’s
network resources and also communicate with Internet through PPTP tunnel. It is specified by Russia
Cobrina ISP, user can configure it the same as the normal PPTP and PPTP server IP Address can use
the domain name string.
WAN MTU Setting:The Maximum Transmission Unit (MTU) is a parameter that determines the largest
packet size (in bytes) that the router will send to the WAN. If LAN devices send larger packets, the router
will break them into smaller packets. Ideally, you should set this to match the MTU of the connection to
your ISP. Typical values are 1500 bytes for an Ethernet connection and 1492 bytes for a PPPoE
connection. If the router's MTU is set too high, packets will be fragmented downstream. If the router's
MTU is set too low, the router will fragment packets unnecessarily and in extreme cases may be unable
to establish some connections. In either case, network performance can suffer. t modes.
MAC Address Clone: Each networking device has it's own unique MAC address defined by the
hardware manufacturer. Some ISP's may check your computer's MAC address. Some ISP's record the
MAC address of the network adapter in the computer or router used to initially connect to their service.
The ISP will then only grant Internet access to requests from a computer or router with this particular
MAC address. This router has a different MAC address than the computer or router that initially
connected to the ISP. If you need to change the MAC address of the rounter's WAN-side Ethernet
interface, either type in an alternate MAC address (for example, the MAC address of the router initially
connected to the ISP) or copy the MAC address of a PC. To copy the MAC address of the computer that
initially connected to the ISP, connect to the router using that computer and click the Clone Your PC's

17
MAC Address button. The WAN interface will then use the MAC address of the network adapter in your
computer.
LAN SETTING
IP Address:The IP address of the this device on the local area network. Assign any unused IP address
in the range of IP addresses available for the LAN.
Subnet Mask: The subnet mask of the local area network.
DHCP Server Settings: DHCP stands for Dynamic Host Configuration Protocol. The DHCP section is
where you configure the built-in DHCP Server to assign IP addresses to the computers and other
devices on your local area network (LAN).
Enable DHCP Server: Once your router is properly configured and this option is enabled, the DHCP
Server will manage the IP addresses and other network configuration information for computers and
other devices connected to your Local Area Network. There is no need for you to do this yourself.
The computers (and other devices) connected to your LAN also need to have their TCP/IP configuration
set to "DHCP" or "Obtain an IP address automatically". When you set Enable DHCP Server, the
following options are displayed.
DHCP IP Address Range: These two IP values (Start and End) define a range of IP addresses that the
DHCP Server uses when assigning addresses to computers and devices on your Local Area Network.
Any addresses that are outside of this range are not managed by the DHCP Server; these could,
therefore, be used for manually configured devices or devices that cannot use DHCP to obtain network
address details automatically.
It is possible for a computer or device that is manually configured to have an address that does reside
within this range. In this case the address should be reserved, so that the DHCP Server knows that this
specific address can only be used by a specific computer or device.
Your router, by default, has a static IP address of 192.168.10.1. This means that addresses
192.168.10.2 to 192.168.10.254 can be made available for allocation by the DHCP Server.
Subnet Mask: The subnet mask of the local area network.
Gateway: The IP address of the router on the local area network. For example, 192.168.10.1.
DHCP Lease Time: The amount of time that a computer may have an IP address before it is required to
renew the lease. The lease functions just as a lease on an apartment would. The initial lease designates
the amount of time before the lease expires. If the tenant wishes to retain the address when the lease is
expired then a new lease is established. If the lease expires and the address is no longer needed than
another tenant may use the address.
Add/Edit DHCP Reservation: This option lets you reserve IP addresses, and assign the same IP
address to the network device with the specified MAC address any time it requests an IP address. This
is almost the same as when a device has a static IP address except that the device must still request an
IP address from the router. The router will provide the device the same IP address every time. DHCP

18
Reservations are helpful for server computers on the local network that are hosting applications such as
Web and FTP. Servers on your network should either use a static IP address or use this option.
Computer Name: You can assign a name for each computer that is given a reserved IP address. This
may help you keep track of which computers are assigned this way. Example: Game Server.
IP Address: The LAN address that you want to reserve.
MAC Address: To input the MAC address of your system, enter it in manually or connect to the router's
Web-Management interface from the system and click the Copy Your PC's MAC Address button.
A MAC address is usually located on a sticker on the bottom of a network device. The MAC address is
comprised of twelve digits. Each pair of hexadecimal digits are usually separated by dashes or colons
such as 00-0D-88-11-22-33 or 00:0D:88:11:22. If your network device is a computer and the network
card is already located inside the computer, you can connect to the router from the computer and click
the Copy Your PC's MAC Address button to enter the MAC address.
Clear: Re-initialize this area of the screen, discarding any changes you have made.
DHCP Reservations List: This shows clients that you have specified to reserve DHCP addresses. Click
the Enable checkbox at the left to directly activate or de-activate the entry. An entry can be changed by
clicking the Edit icon or can be deleted by clicking the Delete icon. When you click the Edit icon, the item
is highlighted, and the "Edit DHCP Reservation" section is activated for editing.
QOS
QoS involves prioritization of network traffic. QoS can be targeted at a network interface, toward a given
server or router's performance, or in terms of specific applications.

19
Upload Bandwidth: Limit bandwidth of upload manually with ‘User Defined’ or set the bandwidth limit
via drop-down menu (between 64Mbits ~ 230Mbits) per device on network.
DHCP CLIENT LIST
This section displays all connected LAN devices currently receiving IP address from the router.

20
Wireless 2.4GHz
BASIC
Radio On/Off: This indicates the wireless operating status. The wireless can be turned on or off by the
slide switch. When the radio is on, the following parameters are in effect.
Wireless Mode: If all of the wireless devices you want to connect with this router can connect in the
same transmission mode, you can improve performance slightly by choosing the appropriate wireless
mode. If you have some devices that use a different transmission mode, choose the appropriate
wireless mode. The TEW-692GR supports 2.4GHz wireless networks. There are many different
configuration options available to choose from. Use the drop down list to select the wireless mode.
Note: One wireless mode can be selected can select at any one time. This means that you can only
select one of the operating frequency at a time.
Wireless Mode options: 2.4GHz 802.11b/g mixed mode - This wireless mode works in the 2.4GHz
frequency range and will allow both wireless b and wireless g client to connect and access the