Trendstyle 1000mm User manual

1000mm
blind corner base cabinet
www.trendstyle.com.au
Step 1
Follow these instructions to
build and attach your cabinet.
Hardware included
Tools you will need
To put your trendstyle cabinets together you will need the following tools.
Cordless drill with:
• Number 2 screw tip
• 4mm drill bit
• Number 12
countersinking drill bit
Tape
measure
E
adjustable
legs x 6
C
shelf
support x 5
F
90° angle
bracket x 10
G
stick on end
caps x 8
Pencil Clamps Safety
gear
Adjustable
square
65mm
wood screw
Spirit level
(900mm recommended)
Wall fixing
(If necessary)
page 1
B
28mm
wood screws x 28
A
50mm
wood screws x 25
H
door
buffer x 2
D
14mm
screws x 20
Before you get started
All cabinets will need to be attached to the wall using a minimum of
8 gauge 65mm screws if you have a stud wall. If your wall is
concrete, brick or another surface ask your hardware specialist for
advice on the right fixing method.
To help identify panels, counter sunk holes always face
outwards.
All holes that aren’t already pre-drilled should be drilled prior to
screwing using a No 12 countersinking drill bit.
Make sure you always use safety gear like a mask, ear muffs and
glasses when using tools.
Make sure you leave plumbing and electrical work to qualified trades
people. Never try this yourself.
For extra strength use exterior woodworking glue when
assembling cabinets.

www.trendstyle.com.au
1000mm blind corner base cabinet
page 2
Set height of the adjustable feet to 145mm.
What you will need
joining cabinets
Step 1
1
4 5 6
2 3
7 8 9
Cabinet complete
Cabinet frame now complete
E
adjustable
legs
C
shelf
support
B
28mm
wood screws
A
50mm
wood screws
A
bottom panel
back panel
A
side panel
side panel
back panel
A
side panel
side panel
support rail
back panel
Pre-drilled
holes
E
B
145mm E
C

www.trendstyle.com.au
Installing adjustable shelf
rebated backs
Step 1
12
1000mm blind corner base cabinet
What you will need
B
28mm
wood screws x 19
1
B
When you need to add an end
panel check out the end panel
instructions for installation tips.
rebated backs
Base cabinets have been designed with the
ability to assemble your back panel to create a
16mm rebate. The rebated panels can be
trimmed down to accommodate uneven walls.
Note: The gap behind your cabinets needs
to be packed out before screwing to the wall.
fixing cabinets to wall
1stud
plaster board
Caution: Please ensure all cabinets
are screwed into your timber stud
wall using a minimum of 65mm
timber screws. If attaching to
concrete, brick, steel or any other
substrates seek advice from your
hardware specialist.
Please note: For use with
a 450mm door, but can be
adapted to use other door
sizes if necessary.
Check that all cabinets are level and screw
into wall using the correct fixings.
page 3

blind corner base panel
www.trendstyle.com.au
Step 2
Follow these instructions to fit
your doors and panels.
Before you get started
Make sure you leave plumbing and electrical work to qualified trades
people. Never try this yourself.
Gloss vinyl doors & panels are protected with a top clear wrap that
needs to be removed. Depending on application of the panel, this may
need to be removed prior to installation.
All holes that aren’t already pre-drilled should be drilled prior to
screwing using a No 12 countersinking drill bit.
Hardware needed
Tools you will need
To put your trendstyle cabinets together you will need the following tools.
Make sure you always use safety gear like a mask, ear muffs and
glasses when using tools.
page 4
A
14mm
wood screws x 16
B
90° angle
bracket x 8
Cordless drill with:
• Number 2 screw tip
• 4mm drill bit
• Number 12
countersinking drill bit
Tape
measure
Pencil Clamps Safety
gear
Adjustable
square
Spirit level
(900mm recommended)

www.trendstyle.com.au
cabinet configurations
attaching panel
Step 2
1 2
3
blind corner base panel
What you will need
page 5
A
14mm
wood screws
B
90° angle
bracket
You can change the orientation of the
cabinet for either Left or Right opening via
the placement of the blind corner panel on
to the cabinet. Consider the layout of your
kitchen before installing the panel.
Mark a line 66mm all the way down the
panel in from the side of the panel on the
opposite end to the lugs.
Attach the panel to cabinet making sure the
marked line is even with the side of the cabinet.
66mm
A
B
400 –600mm
Note: This measurement is to suit a
450mm door. It can be adapted to suit
other sized doors if necessary.
Note: To fit different sized doors simply
install the blind corner base panel on the
cabinet allowing the appropriate space to
suit. If you intend to install any pullout
wireware products, please ensure you
choose the correct door size and fit the
blind corner base panel to match.

www.trendstyle.com.au
Step 2 blind corner base panel
page 6
Step 1
Your Trendstyle cabinet
is now complete.
Step 2
Then follow the instructions to
fit your door and panels.
Your new Trendstyle cabinets are made from quality
products in order to last you for many years, as long as
the right care and maintenance is undertaken.
When cleaning your cabinets, ensure you use a
non-abrasive cleaner, do not use materials like
steel-wool or abrasive items that can scratch and
damage your cupboards. Avoid harsh chemicals or
thinner based products as these will damage the
melamine surfaces. While our Trendstyle cabinets are
water resistant, they are not water proof, so ensure
your cleaning cloths are only damp and not saturated.
If large spills of water occur, ensure these are attend-
ed to immediately.
We offer a dedicated customer service line for
advice or any questions you may have on
Trendstyle products.
Caring for your cabinets
[phone]
[email protected]
Call customer service on
important information
NOTE: Some handles in certain configurations can
collide with each other when doors are open,
potentially causing the blind corner cabinet doors to
not open wide enough to access the pantry.
Test your chosen handles before installing and if you
find that this is the case you will need to either adjust
the positions of the handles, choose different
handles, or use push to open mechanisms without
any handles.
Alternately you can move your entire blind corner
cabinet away from the wall 50mm* so that the blind
corner panel sits out from the adjoining cabinet by
90mm rather than 40, leaving room for the handles to
open. When the benchtop is installed you will not be
able to see the gap between the cabinet and wall.