Triangle Lights LED PAR 64 6CH LCD 181 LONG User manual

LED PAR 64 6CH LCD 181 LONG
USER MANUAL
1 Specifications
Number of LEDs 181X10MM LED（R:49, G:72, B:60）
Power Consumption 20W
Beam angle 25° OR 18°
Projecting distance 10-15M
LED Lumen
LED Expected Life 80,000 hours
Control system DMX 512
DMX Channel 6 Channels
Connection 3 pins XLR-sockets
Input Voltage 100V~256VAC
Operating Voltage 24VDC
LED Current 320mA ±5%
Dimension 19 (Inner Diameter is 18, Height excluding bracket is 25.5)CM
Housing Metal. Black or Chrome
Weight 3kgs±5%
Package Dimension 24X24X50CM
www.storexp.com
[email protected]

2 Control Modes
Stand Alone Mode Select effects using the LCD panel
DMX International standard DMX512 signal control
3 LCD Control Panel
1- Menu Push button to Navigate through the menu. This button does NOT keep you in the MAIN
MENU but it will browse all the menu options WITHIN the MAIN menu OPTION that was SAVED last
time it was turned on. There are two MAIN menu options, so you are either in one or the other. See
Section 4 for menu structure and you will understand it better.
2- Page Down Use this button to navigate or set value when you have navigated to the right screen.
3- Page Up Use this button to navigate or set value when you have navigated to the right screen.
4- Enter Confirm your selections or settings
Find out which mode this light is in, and switch between modes.
Push Menu button until you see either ADDR or nASt.
If you see ADDR, you are in DMX mode, Otherwise you are in Stand Alone mode.
To Change from DMX mode to Stand Alone mode:
1, Go to screen ADDR by pushing MENU button
2, push Up/Down button to get nASt.
3, push Enter to Confirm
www.storexp.com
[email protected]

www.storexp.com
[email protected]
4 LCD Control in Details
Main and Sub Level Menus are shown below:
Main
Menu Sub Menu Description
A001-A512 DMX Address. Refer to Section 5 for DMX Chart.
PR01-PR16 No Function
ADDR: SP01-SP08 No Function
A001-A512 No Function
PR01-PR16 Select 16 lighting effects with Up/Down button.
nASt SP01-SP08 Select 8 level of speed for strobe, fading or color change, which is available in
PR01-PR16.
Now you can go back to Section 3 to see what the Menu button do.
Note in the above table, in ADDR option, only Address Setting is working. The other two sub-menu options
will only work/respond in nASt option.

www.storexp.com
[email protected]
5 DMX CHART
Channel No. DMX Value Description
1 0~255 Red Dimmer
Used in combination with CH6 to get color. Add CH5 to get strobe.
2 0~255 Green Dimmer
Used in combination with CH6 to get color. Add CH5 to get strobe.
3 0~255 Blue Dimmer
Used in combination with CH6 to get color. Add CH5 to get strobe.
0~15 No Function
16~120 Color Macro.
The lights will output Red, Green, Blue; Cyan, Yellow, Magenta and
White. Each color is 15 dmx points apart.
121~225 Color Macro with Strobe.
Each color takes 15 dmx points. Strobe speed will increase
when you increase dmx value within each color macro.
226~240 Color Macro with changing color. No fading effect.
Changing speed increase as dmx value increases.
4
241~255 As above
0~127 No Function
5 128~255 Strobe.
Increase speed by increase the dmx value.
Used in combination with CH6 and CH1,2, or 3.
6 0~255 Dimmer.
Used in combination with CH1,2,3 to get color. Add CH5 to get color with
strobe.
6 Warning
This fixture is not waterproof and not to be used outdoor unless tended all time.

www.storexp.com
[email protected]
7 Trouble-Shooting
3 of the leds are not working when I received the lights.
LEDs are soldered to the led board and they work in sets of 3. If one solder point get loosen due to impacts
in transit, it will bring down the other two in the group. Fixing this is easy if you have a solder iron.
Open the case, locate the 3 leds that are not working, and go to the other side of the led board where you
see the connections.
Plug and light in, and touch/press the connection for each of the 3 leds with your finger, and see if the 3
leds light up.
The one that lights up all 3 leds is the connection that needs to be soldered. Youtube guide on how to
correctly solder can be found here: http://www.youtube.com/watch?v=MHNDa2Wvk8I
8 Errors/Mistakes and Recommendations
Please write me at [email protected] for any errors/mistakes, or improvements that
you think would make it a better manual.
We appreciate your help and will offer discounts for your next purchase depending on
how much you contribute.