Tricolor Multi-Viewer User manual

-1-
User Manual
HDMI 4x1 Quad Multi-Viewer With Seamless
Switcher

-I-
Contents
1. Introduction...............................................................................................1
2. Feature....................................................................................................... 1
3. Specification.............................................................................................. 2
4. Operation Controls and Functions......................................................... 2
4.1. Front Panel............................................................................................................. 2
4.2. Rear Panel...............................................................................................................3
5. Connection Diagram................................................................................ 4

-1-
1. Introduction
This product is a high performance 4 by 1 Quad Multi-Viewer with Seamless switcher. It
supports four High definition input source display on one screen, and have three multi-view
effect mode. As a switcher, it can also seamlessly switch the four HD input freely. The
product can be controlled by various ways, through the front panel button control, IR control,
RS232 control etc. The product provides an S/PDIF link to output the HDMI source audio at
the same time. In addition, this product have basic version and extender version. The Extender
version can extend the video and audio signals over single 50m CAT5e/6 with Bidirectional
IR control.
2. Feature
Compliant with HDMI 1.3a,HDCP 1.2；
Supports multiplexed HDMI 4-input and 1-output；
Supports up to 1080p High Definition resolution；
Support 4by1 Quad Multi-viewer and seamless switch；
Support scaler up,scaler down function；
Support multi output resolution；
Support digital audio format LPCM/AC3/DTS
Support button,IR,RS232 etc various controlled ways；
IR system allowing for control of source at display end；
Allows HDMI Audio/Video and IR signals to be transmitted over a
single Cat5e/6 cable(Extender Version)

-2-
3. Specification
Video Bandwidth
2.25Gbps
Input Ports
4 × HDMI (Female type)
Output Ports
1 × HDMI (Female type),
Audio output
PCM2, 5.1, 7.1CH, Dolby 5.1, DTS5.1
Input Resolution
480i60Hz, 480p60Hz, 576i50Hz, 576p50Hz, 720p50/60Hz,
1080i50/60Hz, 1080p24/30/50/60Hz, 800x600@60, 1024x768@60,
1280x720@60, 1920x1080@60;
Output Resolution
1080p, 720p, 1080i,1024x768,1360x768
ESD Protection
Human Body model:
±8 kV (air-gap discharge)
±4 kV (contact discharge)
Power Supply
12V/2.5A DC (US/EU standards, CE/FCC/UL certified)
Dimensions
250mm (W)×118mm (D)×32 mm (H)
Weight
750 g
Chassis Material
Metal
Operating Temperature
0 °C~40 °C/ 32 °F~104 °F
Storage Temperature
−20 °C ~ 60 °C/−4 °F ~140 °F
Relative Humidity
20~90 % RH (non-condensing)
Power Consumption (Max)
10W
4. Operation Controls and Functions
4.1. Front Panel

-3-
1) ON/OFF: Power on/off switch.
2) SERVICE: For factory use only.
3) IR : Remote control receiver window.
4) POWER LED: This red LED illuminates when the device is connected with power
supply.
5) IN1,2,3,4 LED: These red LED illuminates when the output select to the corresponding
input.
6) INPUT BUTTON: Press this button to select the input source.
7) MODE BUTTON: Press this button to select the multi-view display mode.
※see the detail description below(chapter V.7).
8) RESO BUTTON: Press this button to select the HDMI output
resolution
4.2. Rear Panel
1) Input: These slot is where you connect the HDMI source output
from DVD, PS3,Set-top Box and Note Book.
2) OUTPUT: The HDMI is where you connect the HDTV or

-4-
monitor with HDMI cable for input source display.The UTP port
connect to CAT Receiver by CAT5e/6 cable for signal
extend.The Coax is where you connect to the amplifier with
coaxial cable.
3) IR RX: Connect to the IR Receiver for IR signal reception.
Ensure that remote being used is within the direct line-of-sight
of the IR receiver.
4) IR TX: Connect the IR Blaster cable included in the package for
IR signal transmission. Pace the IR blaster in direct line-of-sight
of the equipment to be controlled.
5) RS232: Connect the RS232 port to the PC or notebook by
Rs232
Cable.
6) DC 12V: Plug the 12V DC power supply into the unit and
connect the adaptor to AC wall outlet.
5. Connection Diagram

-5-