Trim a Home 0-03431420-3 User manual

Made in / Hecho en CHINA. Distributed by Kmart Corporation
Hoffman Estates, IL 60179 SHOP kmart.com
For questions or comments about the product:
Email: [email protected] or Call toll-free: 1-855-428-6664
OWNER’S MANUAL
4.5 FT STICK TREE
Product code: 0-03431420-3 (clear), 0-03431421-1 (multi)
UPC code: 029944490890 (clear), 029944491019 (multi)
Date of purchase: _____/ _____/ _____

4.5 FT STICK TREE
ITEM NUMBER: TY-T4.5-300L
A. Tree tip
Qty：1pc
B. Branch bundle
Qty：2pcs
C. Pole section
Qty：1pc
D. Ground stake
Qty：1pc
E. Bow of stand with one tube
Qty：1pc
F. Bow of stand with two
tube
Qty：1pc
G. Plastic cap
Qty：1pc
H. String/hook
Qty：4pcs
I. Screw
Qty：4pcs
J. Stake
Qty：4pcs
K. Wing nut/bolt
Qty：2pcs
L. Bulb extractor
Qty：1pc
ASSEMBLY INSTRUCTIONS
FOR INDOOR USE
STEPS: (1)Place all the parts on a flat surface. (2) Align the inner piece and outer piece of tree stand to fit
together, insert the short pole into the center tube of tree stand. Fasten them with the screws
pre-attached. (You will not use ground stake for indoor use). (3) Place the lower half of the tree into the
upper end of short pole and tighten them together with the screw and nut provided. (4) Place the lower
end of the upper half into the pole of the lower half and tighten them together with the screw and nut
provided. (5) Place the tree tip into the top of the tree. (6) The branches are pre-bundled. Gently pull the
branches apart. Make sure the inner end of each main branch is properly secured in the hook on the pole.
(7) Gently pull the mini branches apart to form a fully extended tree shape. (8) Connect the two halves of
the tree together with their plug and end plug. (9) Plug in.
FOR OUTDOOR USE
STEPS: (1) Place the driving cap on the top of the sharp pole stake and drive the pole stake into the
ground. (You will not use stand pieces for outdoor use.) Insert the short pole into the center tube of tree
stand.(2) Place the lower half of the tree into the upper end of short pole and tighten them together with
the screw and nut provided. (3) Place the lower end of the upper half into the pole of the lower half and
tighten them together with the screw and nut provided. (4) Place the tree tip into the top of the tree. (5)
The branches are pre-bundled. Gently pull the branches apart. Make sure the inner end of each main
branch is properly secured in the hook on the pole. (6) Gently pull the mini branches apart to form a fully
extended tree shape. (7) Connect the two halves of the tree together with their plug and end plug. (8) Each
anchoring string provided has a "S" hook at one end. Tie up the free end to the ground stake. Evenly
attach each "S" hook of four strings to the root of each cluster of branches as shown.
(9) Pull the string tight and drive the ground stake at the other end into the ground. (10) Plug in.
The use of the bulb extractor
If one bulb burned out or is not lit,you can use the bulb extractor to remove the burned-out bulb from the
tree and replace it with the spare bulb provided
1) Push the base of the bulb extractor into the lamp holder (diagram.1 & 2)
2) Pull out the lamp holder from the lamp base (diagram. 2 & 3)
diagram.1 diagram.2 diagram.3